Move the existing sunxi-specific low level pinctrl routines from
arch/arm/mach-sunxi into the existing GPIO code under drivers/gpio, so
that the common code can be shared outside of arch/arm.
This also takes the opportunity to move some definitions from our
header file into the driver C file, as they are private to the driver
and are not needed elsewhere.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
The CONFIG_MACPWR Kconfig symbol is used to point to a GPIO that enables
the power for the Ethernet "MAC" (mostly PHY, really).
In the DT this is described with the phy-supply property in the MAC DT
node, pointing to a (GPIO controlled) regulator. Since we need Ethernet
only in U-Boot proper, and use a DM driver there, we should use the DT
instead of hardcoding this.
Add code to the sun8i_emac and sunxi_emac drivers to check the DT for
that regulator and enable it, at probe time. Then drop the current code
from board.c, which was doing that job before.
This allows us to remove the MACPWR Kconfig definition and the respective
values from the defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
At the moment the sun4i EMAC driver relies on hardcoded CONFIG_MACPWR
Kconfig symbols to enable potential PHY regulators. As we want to get rid
of those, we need to find the regulator by chasing up the DT.
The sun4i-emac binding puts the PHY regulator into the MDIO node, which
is the parent of the PHY device. U-Boot does not have (and does not
need) an MDIO driver, so we need to chase down the regulator through the
EMAC node: we follow the "phy-handle" property to find the PHY node,
then go up to its parent, where we find the "phy-supply" link to the
regulator. Let U-Boot find the associated regulator device, and put that
into the private device struct, so we can find and enable the regulator
at probe time, later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
The CONFIG_SATAPWR Kconfig symbol was used to point to a GPIO that
enables the power for a SATA harddisk.
In the DT this is described with the target-supply property in the AHCI
DT node, pointing to a (GPIO controlled) regulator. Since we need SATA
only in U-Boot proper, and use a DM driver for AHCI there, we should use
the DT instead of hardcoding this.
Add code to the sunxi AHCI driver to check the DT for that regulator and
enable it, at probe time. Then drop the current code from board.c, which
was doing that job before.
This allows us to remove the SATAPWR Kconfig definition and the
respective values from the defconfigs.
We also select the generic fixed regulator driver, which handles those
GPIO controlled regulators.
Please note that the OrangePi Plus is a bit special here, it's a H3
board without native SATA, but with a USB-to-SATA bridge. The DT models
the SATA power via a VBUS supply regulator, which we don't parse yet in
the USB PHY driver. Use the hardcoded CONFIG_USB3_VBUS_PIN for that
board meanwhile.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators and may be further expanded on all
regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators and may be further expanded on all
regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators and may be further expanded on all
regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Extend the existing driver to support the SCIF serial ports on the
Renesas RZ/G2L (R9A07G044) SoC. This also requires us to ensure that if
there is a reset signal defined in the device tree, it is de-asserted
before we try to talk to the SCIF module.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # R-Car H3 Salvator-XS
The current SCIF error handling is broken for the RZ/G2L. After a break
condition has been triggered, the current code is unable to clear the
error and serial port output never resumes.
The RZ/G2L datasheet says that most error conditions are cleared by
resetting the relevant error bits in the FSR & LSR registers to zero.
To clear framing errors on SCIF ports, the invalid data also needs to be
read out of the receive FIFO.
After reviewing datasheets for RZ/G2{H,M,N,E}, R-Car Gen4, R-Car Gen3
and even SH7751 SoCs, it's clear that this is the way to clear errors
for all of these SoCs.
While we're here, annotate the handle_error() function with a couple of
comments as the reads and writes themselves don't immediately make it
clear what we're doing.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Tested-by: Chris Paterson <chris.paterson2@renesas.com> # HiHope RZ/G2M board
Tested-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # R-Car H3 Salvator-XS
Fix npcm845 watchdog halt for reset function and expire function.
Reset function is restart wdt.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The ST M24C32-D behaves as a regular M24C32, except for the -D variant
which uses up another I2C address for Additional Write lockable page.
This page is 32 Bytes long and can contain additional data. Add entry
for it, so users can describe that page in DT. Note that users still
have to describe the main M24C32 area separately as that is on separate
I2C address from this page.
From Linux kernel commit:
4791146e9055 ("eeprom: at24: add ST M24C32-D Additional Write lockable page support")
Signed-off-by: Marek Vasut <marex@denx.de>
The i.MX93 11x11 EVK fails to boot with following error:
Model: NXP i.MX93 11X11 EVK board
DRAM: 2 GiB
Error binding driver 'imx93-adc': -96
Some drivers failed to bind
Error binding driver 'simple_bus': -96
Some drivers failed to bind
Error binding driver 'simple_bus': -96
Some drivers failed to bind
initcall sequence 00000000fffb8f28 failed at call 000000008021e0d4 (err=-96)
### ERROR ### Please RESET the board ###
That's because since commit e7ff54d963 ("imx93_evk: defconfig: add adc
support") CONFIG_ADC_IMX93 is enabled but CONFIG_ADC is not.
Fix this by enabling CONFIG_ADC in imx93_11x11_evk_defconfig.
Make sure this situation won't happen again in future i.MX93 defconfig by
making CONFIG_ADC_IMX93 depend on CONFIG_ADC.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Patch which add A1 SoC support create a regression on khadas vim3/vim3l
boards when we try to use fastboot command:
=> fastboot usb 0
failed to get power domain
failed to get power domain
No USB device found
USB init failed: -19
Add ENOENT check on ret in probe function.
Fixes: 5533c883ce ("phy: support Amlogic A1 family")
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231017185725.809524-1-glaroque@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
lib/acpi/acpigen.o is only compiled into SPL when SPL_ACPIGEN is enabled.
Update several files which reference these functions accordingly.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sandbox unit tests in U-Boot proper load a test device tree to have some
devices to work with. In order to do the same in SPL, we must enable
SPL_OF_REAL. However, we already have SPL_OF_PLATDATA enabled. When
generating platdata from a devicetree, it is expected that we will not need
devicetree access functions (even though SPL_OF_CONTROL is enabled). This
expectation does not hold for sandbox, so allow user control of
SPL_OF_REAL.
There are several places in the tree where conditions involving OF_PLATDATA
or OF_REAL no longer function correctly when both of these options can be
selected at the same time. Adjust these conditions accordingly.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make sure we have an IMX header before calling spl_load_imx_container,
since if we don't it will fail with -ENOENT. This allows us to fall back to
legacy/raw images if they are also enabled.
This is a functional change, one which likely should have been in place
from the start, but a functional change nonetheless. Previously, all
non-IMX8 images (except FITs without FIT_FULL) would be optimized out if
the only image load method enabled supported IMX8 images. With this change,
support for other image types now has an effect.
There are seven boards with SPL_LOAD_IMX_CONTAINER enabled: three with
SPL_BOOTROM_SUPPORT:
imx93_11x11_evk_ld imx93_11x11_evk imx8ulp_evk
and four with SPL_MMC:
deneb imx8qxp_mek giedi imx8qm_mek
All of these boards also have SPL_RAW_IMAGE_SUPPORT and
SPL_LEGACY_IMAGE_FORMAT enabled as well. However, none have FIT support
enabled. Of the six load methods affected by this patch, only SPL_MMC and
SPL_BOOTROM_SUPPORT are enabled with SPL_LOAD_IMX_CONTAINER.
spl_romapi_load_image_seekable does not support legacy or raw images, so
there is no growth. However, mmc_load_image_raw_sector does support loading
legacy/raw images. Since these images could not have been booted before, I
have disabled support for legacy/raw images on these four boards. This
reduces bloat from around 800 bytes to around 200.
There are no in-tree boards with SPL_LOAD_IMX_CONTAINER and AHAB_BOOT both
enabled, so we do not need to worry about potentially falling back to
legacy images in a secure boot scenario.
Future work could include merging imx_container.h with imx8image.h, since
they appear to define mostly the same structures.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
On the Renesas RZ/G2L SoC family, we must ensure that the required clock
signals are enabled and the reset signal is de-asserted before we try to
communicate with the SDHI module.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Move the assignment of priv->quirks earlier in the function. This allows
us to drop the quirks local variable and makes it easier to maintain
clean error handling when we add RZ/G2L support in the next patch.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tidy up the existing include list before we add more includes in the
following patch.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This driver adds support for the gpio features of the GPIO/PFC module in
the Renesas RZ/G2L (R9A07G044) SoC.
The new `rzg2l-pfc-gpio` driver is bound to the same device tree node as
the `rzg2l-pfc-pinctrl` driver as the same hardware block provides both
GPIO and pin multiplexing features.
This patch is based on the corresponding Linux v6.5 driver
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This driver adds support for the pinctrl features of the GPIO/PFC module
in the Renesas RZ/G2L (R9A07G044) SoC.
A multi-function `rzg2l-pfc` driver is defined for UCLASS_NOP, which
binds the `rzg2l-pfc-pinctrl` UCLASS_PINCTRL driver dynamically. We also
define common macros and functions for the PFC in <renesas/rzg2l-pfc.h>.
This makes it easy to add an additional UCLASS_GPIO driver for the GPIO
functionality of this module in a follow-up patch.
This patch is based on the corresponding Linux v6.5 driver
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This driver provides clock and reset control for the Renesas R9A07G044L
(RZ/G2L) and R9A07G044C (RZ/G2LC) SoC. It consists of two parts:
* driver code which is applicable to all SoCs in the RZ/G2L family.
* static data describing the clocks and resets which are specific to the
R9A07G044{L,C} SoCs. The identifier r9a07g044 (without a final letter)
is used to indicate that both SoCs are supported.
clk_set_rate() and clk_get_rate() are implemented only for the clocks
that are actually used in u-boot.
The CPG driver is marked with DM_FLAG_PRE_RELOC to ensure that its bind
function is called before the SCIF (serial port) driver is probed. This
is required so that we can de-assert the relevant reset signal during
the serial driver probe function.
This patch is based on the corresponding Linux v6.5 driver
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
If we attempt to compile serial_sh.c for a system which lacks HSCIF
support (e.g. R8A7740), we see the following compilation error:
In file included from drivers/serial/serial_sh.c:20:
drivers/serial/serial_sh.c: In function ‘sh_serial_init_generic’:
drivers/serial/serial_sh.h:429:35: warning: implicit declaration of function ‘sci_HSSRR_out’; did you mean ‘sci_SCSCR_out’? [-Wimplicit-function-declaration]
429 | #define sci_out(port, reg, value) sci_##reg##_out(port, value)
| ^~~~
drivers/serial/serial_sh.c:62:17: note: in expansion of macro ‘sci_out’
62 | sci_out(port, HSSRR, HSSRR_SRE | HSSRR_SRCYC8);
| ^~~~~~~
To fix this, only try to support access to the HSSRR register for SoCs
where it actually exists.
Support for the RZ/G2L will be introduced in following patches, which
selects CONFIG_RCAR_64 but does not have HSCIF interfaces, so check for
CONFIG_RCAR_GEN2 || CONFIG_RCAR_GEN3 || CONFIG_RCAR_GEN4 to determine if
HSCIF is present.
Fixes: bbe36e29ca ('serial: sh: Add HSCIF support for R-Car SoC')
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Cc: Hai Pham <hai.pham.ud@renesas.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Current codes only ennable the PER clock. However on iMX8 the LPUART
also needs IPG clock which is an LPCG. Should not depend on the default
LPCG setting.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Add i.MX93 CCF driver support.
Modifed from Linux Kernel v6.5-rc2 and adapted for U-Boot.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Add hook in sata_mv probe to enable bootstd bootdev.
Note: bootdev_setup_for_sibling_blk() invocation is a noop if bootsd is
not enabled for ahci sata yet.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Since commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable() may be EALREADY or
EBUSY for fixed/GPIO regulators.
Switch to using the more relaxed regulator_set_enable_if_allowed() to
continue if regulator already was enabled or disabled.
This fixes the following error when running the 'ums' command:
=> ums 0 mmc 0
UMS: LUN 0, dev mmc 0, hwpart 0, sector 0x0, count 0xece000
Error enabling VBUS supply
g_dnl_register: failed!, error: -114
g_dnl_register failed
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Use dev_ofnode() to retrieve the USB node pointer from the udevice
structure.
This fixes the following build error:
drivers/usb/host/ehci-mxs.c:143:38: error: 'struct udevice' has no member named 'node_'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
This patch adds an implementation of the Meson Secure Monitor
driver based on UCLASS_SM.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921081346.22157-7-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
At the moment, we don't have a common API for working with
SM, only the smc_call() function. This approach is not generic
and difficult to configure and maintain.
This patch adds UCLASS_SM with the generic API:
- sm_call()
- sm_call_write()
- sm_call_read()
These functions operate with struct pt_regs, which describes
Secure Monitor arguments.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921081346.22157-2-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
scan all entries in multi-device boot_targets
EFI empty-capsule support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmUpvTQRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreabCwgAimB2fGpK3FjFMrH1Ko4Qh3j0D/0XomiQ
1KYVbn3YrswLmq1tav9HSKWR3Ep/Uet6jthpH2RPxhcGWNGqxkkk2k4LUudSlIYd
0KKoovMwBK9jZcojoBAjFGaoRIaEBlbFspW/RoXPJnr7ctxf6HSYkW2TPH09zqtD
FrL5Jjf6t0h6QShxhCYXbiHGCnp2zYZRzFnrYpaXy8IIavqWNJTAhkIGveMy+Qa8
TzhmuRamLgtZZwtFcHt8sZuV4+FtBrtHAyiEasnJFPJ5Kv6tFVBiHdYuygZMu/og
+F57ufgqgHTlDjzW72CJyhrHIcVn/mWjNYrulufqHAsSFD7cizISeA==
=qOUT
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-13oct23' of https://source.denx.de/u-boot/custodians/u-boot-dm
improvements with dev_read_addr_..._ptr()
scan all entries in multi-device boot_targets
EFI empty-capsule support
The sess variable in open_channel was not entirely
cleared to zero at the start of this function.
This commit ensures that the entire struct is cleared.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Now that we have Base protocol support, we will be able to check if a given
protocol is really supported by the SCMI server (firmware).
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
SCMI base protocol is mandatory, and once SCMI node is found in a device
tree, the protocol handle (udevice) is unconditionally installed to
the agent. Then basic information will be retrieved from SCMI server via
the protocol and saved into the agent instance's local storage.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Adding SCMI base protocol makes it inconvenient to hold the agent instance
(udevice) locally since the agent device will be re-created per each test.
Just remove it and simplify the test flows.
The test scenario is not changed at all.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
This is a simple implementation of SCMI base protocol for sandbox.
The main use is in SCMI unit test.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
In SCMI base protocol version 2 (0x20000), new interfaces,
BASE_SET_DEVICE_PERMISSIONS/BASE_SET_PROTOCOL_PERMISSIONS/
BASE_RESET_AGENT_CONFIGURATION, were added. Moreover, the api of
BASE_DISCOVER_AGENT was changed to support self-agent discovery.
So the driver expects SCMI firmware support version 2 of base protocol.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
SCMI base protocol is mandatory according to the SCMI specification.
With this patch, SCMI base protocol can be accessed via SCMI transport
layers. All the commands, except SCMI_BASE_NOTIFY_ERRORS, are supported.
This is because U-Boot doesn't support interrupts and the current transport
layers are not able to handle asynchronous messages properly.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
This framework allows SCMI protocols to be installed and bound to the agent
so that the agent can manage and utilize them later.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Move the location of scmi_bind_protocols() backward for changes
in later patches.
There is no change in functionality.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
In sandbox scmi agent, channels are not used at all. But in this patch,
dummy channels are supported in order to test protocol-specific channels.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
SCMI specification allows any protocol to have its own channel for
the transport. While the current SCMI driver may assign its channel
from a device tree, the core function, devm_scmi_process_msg(), doesn't
use a protocol's channel, but always use an agent's channel.
With this commit, devm_scmi_process_msg() tries to find and use
a protocol's channel. If it doesn't exist, use an agent's.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The commit 85dc582892 ("firmware: scmi: prepare uclass to pass channel
reference") added an explicit parameter, channel, but it seems to make
the code complex.
Hiding this parameter will allow for adding a generic (protocol-agnostic)
helper function, i.e. for PROTOCOL_VERSION, in a later patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
A follow-up to commit 842fb5de42
("drivers: use devfdt_get_addr_size_index_ptr when cast to pointer")
and commit 320a1938b6
("drivers: use devfdt_get_addr_index_ptr when cast to pointer").
In addition to using the *_ptr variants of these functions where the
address is cast to a pointer, this also changes devfdt_get_addr_*() to
dev_read_addr_*() in a few places. Some variable and field types are
changed from fdt_addr_t or phys_addr_t to void* where the cast was
happening later.
This patch fixes a number of compile warnings when building a 32bit
U-Boot with CONFIG_PHYS_64BIT=y. In some places, it also fixes error
handling where the return value of dev_read_addr() etc. was checked for
NULL instead of FDT_ADDR_T_NONE.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
pinctrl-single uses fdt_addr_t and phys_addr_t inconsistently, but both
are wrong to be passed to readb() etc., which expect a pointer or
pointer-sized integer. Change the driver to use
dev_read_addr_size_index_ptr(), so we consistently deal with void*
(except for the sandbox case and single_get_pin_muxing()).
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add missing mapmem.h header:
Signed-off-by: Simon Glass <sjg@chromium.org>
Same as dev_read_addr_name[_size](), but returns a pointer, cast
through map_sysmem().
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Checking for the error cast to fdt_addr_t is rather awkward - IS_ERR()
can be used, but it's not really made to be used on fdt_addr_t, which
may not even be the same size as a native pointer.
Most places in U-Boot only check for FDT_ADDR_T_NONE; let's adjust the
error return to match the expectation.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZSjvwAAKCRDKSWXLKUoM
IR34AJ92oum3pJXKxKREEZh0dCfDvJlE/wCggyzxI2T5liJfRG5jzlUuDjiLLU0=
=u1bz
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.01-rc1-v3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2024.01-rc1 v3
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
In the existing implementation, multiple requests queued up on an
endpoint are subject to getting evicted without transmission.
For both control and bulk endpoints, their respective logic found in
usba_control_irq()/usba_ep_irq() guarantees that TX FIFO is empty before
data is sent out, and that request_complete() gets called once the
transaction has been finished. At this point however, if any additional
requests are found on the endpoint queue, they will be processed by
submit_next_request(), which makes no checks against the above
conditions, trashing data on a busy FIFO and neglecting completion
handlers.
Fix the above issues by removing the calls to submit_next_request(),
and thus forcing the pending requests to be processed on the next pass
of the respective endpoint logic. While at it, remove a DBG message, as
that branch becomes part of regular flow.
This restores mass storage mode operation on Microchip ATSAMA5D27 SoC.
Signed-off-by: Artur Rojek <artur@conclusive.pl>
For some Amlogic SOC's, mechanism to obtain random number
has been changed. For example, S4 now uses status bit waiting algo.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231012075828.22685-2-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
In the MTD DFU backend, it is needed to mark the NAND block bad when the
erase failed with the -EIO error, as it is done in UBI and JFFS2 code.
This operation is not done in the MTD framework, but the bad block
tag (in BBM or in BBT) is required to avoid to write data on this block
in the next DFU_OP_WRITE loop in mtd_block_op(): the code skip the bad
blocks, tested by mtd_block_isbad().
Without this patch, when the NAND block become bad on DFU write operation
- low probability on new NAND - the DFU write operation will always failed
because the failing block is never marked bad.
This patch also adds a test to avoid to request an erase operation on a
block already marked bad; this test is not performed in MTD framework
in mtd_erase().
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The offset variable = 'off' used in the error trace when limit is reach
on erase operation is incorect as 'erase_op.addr' is used in the loop.
This patch corrects the copy paste issue between the erase loop and
the write loop.
This patch also adds the 'remaining' information to allow to debug of
limit issues.
Fixes: 6015af28ee ("dfu: add backend for MTD device")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This adds more supported spinand devices from the Linux kernel
implementation.
This does not include the latest kernel implementation as this would
require a substantial amount of extra work due to the missing
ECC engine abstraction layer in U-Boot.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> (commit message)
Link: https://lore.kernel.org/all/20230110115843.391630-3-frieder@fris.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
This brings us closer to the current Linux kernel implementation of
the spinand core and makes backporting features and fixes easier.
This does not include the latest kernel implementation as this would
require a substantial amount of extra work due to the missing
ECC engine abstraction layer in U-Boot.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> (add commit message)
Link: https://lore.kernel.org/all/20230110115843.391630-2-frieder@fris.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Currently there are 3 different variants of read_id implementation:
1. opcode only. Found in GD5FxGQ4xF.
2. opcode + 1 addr byte. Found in GD5GxGQ4xA/E
3. opcode + 1 dummy byte. Found in other currently supported chips.
Original implementation was for variant 1 and let detect function
of chips with variant 2 and 3 to ignore the first byte. This isn't
robust:
1. For chips of variant 2, if SPI master doesn't keep MOSI low
during read, chip will get a random id offset, and the entire id
buffer will shift by that offset, causing detect failure.
2. For chips of variant 1, if it happens to get a devid that equals
to manufacture id of variant 2 or 3 chips, it'll get incorrectly
detected.
This patch reworks detect procedure to address problems above. New
logic do detection for all variants separatedly, in 1-2-3 order.
Since all current detect methods do exactly the same id matching
procedure, unify them into core.c and remove detect method from
manufacture_ops.
This is a rework of Chuanhong Guo <gch981213@gmail.com> patch
submitted to linux kernel
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/all/20230110115843.391630-1-frieder@fris.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
AVS driver needs to be notified before or after clock change,
depending upon new rate is greater or less than current clock rate.
Fixes: 1e0aa873bc7cd ("clk: clk-ti-sci: Notify AVS driver upon setting clock rate")
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
AVS is enabled at R5 SPL stage, on few platforms like J721E
and J7200 clk-k3 is used instead if clk-sci driver.
Add support in clk-k3 driver as well to notify AVS driver
on setting clock rate so that voltage is changed accordingly.
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
We use this clocks in dwc3 driver.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231005085434.74755-7-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Setting G12A and A1 is similar, so we can use G12A phy
driver with little changes.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231005085434.74755-6-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
It is better to use defines instead of write raw
hex values in regmap.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231005085434.74755-4-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
This patch adds reset support for the Amlogic A1 family.
We add the structure meson_reset_drvdata, which in the future
will allow this driver to be used for other families by declaring
only the correct parameters reg_count and level_offset.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231005085434.74755-3-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
This patch adds basic clock driver for Amlogic A1 Family which supports
enabling/disabling some gates, getting frequencies and setting rate
with limited reparenting.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230925155209.130671-3-ivprusov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add rudimentary support for displaying a cursor on a vidconsole. This
helps the user to see where text is being entered.
The implementation so far is very simple: the cursor is just a vertical
bar of fixed width and cannot be erased. To erase the cursor, the text
must be redrawn over it.
This is good enough for expo but will need enhancement to be useful for
the command-line console. For example, it could save and restore the
area behind the cursor.
For now, enable this only for expo, to reduce code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this is called only when a newline is detected, since this
indicates the start of a line of text being entered.
Export this function so it can be used by expo, which may start a new
text line itself, without first writing out a newline.
Signed-off-by: Simon Glass <sjg@chromium.org>
Text entry operates within a context which includes quite a bit of
information. For example, with Truetype fonts, each character in the
text string has a position stored, so that it is possible to
backspace to that character. This information is built up as strings
are drawn on the display.
For the command line, there is just a single context. It is created
when command-line entry starts and it is destroyed (or at least not
needed anymore) when the user presses <enter> to enter the command.
By contrast, expo needs to be able to switch in and out of a text-entry
context, since it is also displaying other objects in the scene.
Add a way to save and restore the entry context for a vidconsole. This
is only needed for the truetype vidconsole, so add a method for that,
storing the information in an abuf struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there is a method for measuring text, but if the actual text
string is not known, it cannot be used.
For text editor we want to set the size of the entry box to cover the
expected text size. Add the concept of a 'norminal' size with a method
to calculate that for the vidconsole.
If the method is not implemented, fall back to using the font size,
which is sufficient for fixed-width fonts.
Signed-off-by: Simon Glass <sjg@chromium.org>
DM_DRIVER_GET will redeclare the fs_loader driver without the correct
alignment. This causes GCC to use the default section alignment of 32
bytes. This in turn creates a gap in the linker list due to the padding
required to achieve the correct alignment, corrupting all further entries.
Use DM_DRIVER_REF instead, which doesn't redeclare anything.
Fixes: 0998a20cfc ("misc: fs_loader: Add function to get the chosen loader")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
The ARMv8.5 architecture extension defines architectural RNDR/RNDRRS
system registers, that provide 64 bits worth of randomness on every
read. Since it's an extension, and implementing it is optional, there is
a field in the ID_AA64ISAR0_EL1 ID register to query the availability
of those registers.
Add a UCLASS_RNG driver that returns entropy via repeated reads from
those system registers, if the extension is implemented.
The driver always binds, but checks the availability in the probe()
routine.
This helps systems which suffer from low boot entropy, since U-Boot can
provide entropy via the generic UEFI entropy gathering protocol to the OS,
at an early stage.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With commit 793e623011 ("spi: mtk_spim: get spi clk rate only once") a
new system to calculate the SPI clocks has been added.
Unfortunately, the do_div macro overrides the global priv->pll_clk_rate
field. This will cause to have a reduced clock rate on each subsequent
SPI call.
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Before using the result of env_get("stdin") we must check if it is NULL.
Avoid #if. This resolves the -Wunused-but-set-variable issue and we don't
need a dummy assignment in the else branch. Anyway this warning is
disabled in the Makefile.
For sake of readability use an early return after the configuration check.
Checking CONFIG_SPL_BUILD is incorrect as env_get() is only defined if
CONFIG_$(SPL_TPL)ENV_SUPPORT=y.
Fixes: 985ca3945f ("spl: input: Allow input in SPL and TPL")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
blk_{read,write}_devnum() are no longer used by anywhere in the
source tree. Drop them.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
get_desc() can be useful outside blk-uclass.c. Let's change it to
an API and make it externally visible.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present if a device to map has a block size other than 512,
the blkmap map process just fails. There is no reason why we
can't just use the block size of the mapped device.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since we are emulating a block device, its size should be multiple
of the configured block size.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allow optionally set the logical block size of the host device to
bind in the "host bind" command. If not given, defaults to 512.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
As the xlnx,phy-type device tree property is deprecated and phy-mode
is being used, so removing the code references of xlnx,phy-type.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231010030436.11854-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reset the FLSHxCR1 registers to default value. ROM may set the register
value and it affects the SPI NAND normal functions.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for declaring in device tree the reserved memory ranges
required for MC. Since the MC firmware acts as any DMA master present
in the SoC, the reserved memory ranges need also be identity mapped
in the SMMU, so create the required 'iommu-addresses' property in
the reserved memory nodes.
For now this support is used only on LX2160A SoCs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The size of the name of a udevice is not limited.
When setting the fixed sized name field of a stdio device we must ensure
that the target string is NUL terminated to avoid buffer overflows.
Fixes: 57d92753d4 ("dm: Add a uclass for serial devices")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This partially reverts commit ff33227819.
Versal NET clock node should use "xlnx,versal-net-clk", "xlnx,versal-clk"
compatible string that's why it is not necessary to define Versal NET
specific compatible string if there is no any other change needed. It can
be get back if there is a need to differentiate clock support between
Versal and Versal NET.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c09276022db5f1b150679cc7a9f9583363ace2fb.1695808971.git.michal.simek@amd.com
Read the tristate config for all the pins and display it.
ZynqMP> pinmux status MIO1
MIO1: slew:fast bias:enabled pull:up input:cmos drive:12mA
volt:1.8 tri_state:enabled
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230914100620.26346-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
MDC clock change needs to be done when the driver probe function
is called as mdio is enabled at probe and not when the ethernet starts.
Setup the MDC clock at the probe itself.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230922045010.22852-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
