Commit graph

504 commits

Author SHA1 Message Date
Fabio Estevam
a768386746 mx6: Read silicon revision from register
Instead of hardcoding the mx6 silicon revision, read it in run-time.

Also, besides the silicon version print the mx6 variant type: quad,dual/solo
or solo-lite.

Tested on a mx6qsabrelite, where it shows:

CPU:   Freescale i.MX6Q rev1.0 at 792 MHz

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <r64343@freescale.com>
2012-03-27 09:41:16 +02:00
Fabio Estevam
334bd0e225 mx6: Remove duplicate definition of ANATOP_BASE_ADDR
Remove duplicate definition of ANATOP_BASE_ADDR.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-03-27 09:41:16 +02:00
Marek Vasut
cd207cde94 IXP: Fix GPIO_INT_ACT_LOW_SET()
The GPIO_INT_ACT_LOW_SET was incorrectly handling interrupt lines higher than 7.
This is due to the fact that there are two registers for total of 16 lines.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
2012-03-26 23:09:26 +02:00
Matt Porter
24de357a30 SPL: Add YMODEM over UART load support
Adds support for loading U-Boot from UART using YMODEM protocol.
If YMODEM support is enabled in SPL and the romcode indicates
that SPL loaded via UART then SPL will wait for start of a
YMODEM transfer via the console port.

Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-03-26 23:09:25 +02:00
Robert Delien
56df16f25a Fix erroneous 32-bit access to hw_clkctrl_frac0 and hw_clkctrl_frac1 registers
This patch fixes erroneous 32-bit access to registers
hw_clkctrl_frac0 and hw_clkctrl_frac1.

Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
2012-03-26 23:09:24 +02:00
Robert Delien
531bb825fd Introducing 8-bit wide register, mx28_register_8
This patch introduces an 8-bit register, mx28_register_8, in order to
prepare for fixing erroneous 32-bit wide access of registers
hw_clkctrl_frac0 and hw_clkctrl_frac1.

Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
2012-03-26 23:09:24 +02:00
Robert Delien
b228e14e96 Renamed mx28_register to mx28_register_32 to prepare for mx28_register_8
This patch renames mx28_register to mx28_register_32 in order to
prepare for the introduction of an 8-bit register, mx28_register_8.

Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
2012-03-26 23:09:24 +02:00
Wolfgang Grandegger
3f467529ca usb/ehci: Add USB support for the MX6Q
Currently, only USB Host 1 is supported.

Cc: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
2012-03-26 23:09:23 +02:00
Robert Delien
c67d9c5e58 i.mx28: Added register definitions for DIGCTL registers
This patch adds register definitions for the registers of the DIGCTL
IP-block.

Signed-off-by: Robert Delien <robert@delien.nl>
2012-03-26 23:09:23 +02:00
Ajay Bhargav
54cb00486e USB: Armada100: EHCI Driver for Armada100 SOCs
This patch adds support for USB EHCI driver for Armada100 SOCs.

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
2012-03-19 00:08:26 +01:00
Ajay Bhargav
732c7c2446 USB: Armada100: Add UTMI PHY interface driver
This patch adds USB host controller's UTMI PHY interface driver for
Armada100 SOCs.

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
2012-03-19 00:08:26 +01:00
Helmut Raiger
d1300f7686 tt01: add video support
The video setup for the Epson display is provided. Addtionally
some extra info is displayed next to the Linux logo.
Make get_cpu_rev() publicly available (added to sys_proto.h).

Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
2012-02-27 21:19:25 +01:00
Troy Kisky
28774cbaac net: fec_mxc: add 1000 Mbps selection
Define FEC_QUIRK_ENET_MAC and add to
arch-mx6/imx-regs.h

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
2012-02-27 21:19:24 +01:00
Chase Maupin
0e35bde7b1 am33xx: ddr_defs.h: Change DDR timings
* For cold silicon the DDR timings need to be relaxed in order for
  the device to boot with DDR at 266MHz
* Fix proposed by James Doublesin

Signed-off-by: Chase Maupin <Chase.Maupin@ti.com>
2012-02-27 21:19:24 +01:00
Eric Nelson
d5c37c9cc4 mx6q: Add support for ECSPI through mxc_spi driver
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
2012-02-27 21:19:23 +01:00
Eric Nelson
08c61a589b mxc_spi: move machine specifics into CPU headers
Move (E)CSPI register declarations into the imx-regs.h files for each supported CPU

Introduce two new macros to control conditional setup
     MXC_CSPI - Used for processors with the Configurable Serial Peripheral Interface (MX3x)
     MXC_ECSPI - For processors with Enhanced Configurable... (MX5x, MX6x)

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
Tested-by: Jason Liu <jason.hui@linaro.org>
2012-02-27 21:19:23 +01:00
Eric Nelson
4b3a30e9ae mx6q: define GPIO macros for translating between ordinals and port:index
The interface to the mxc_gpio driver uses integer (ordinal) values to
refer to all GPIOs on the i.MX processors. The registers themselves
and much of the i.MX documentation are banked in groups of 32, and these
macros allow the use of the port:index numbering for clarity.

GPIO_NUMBER() converts to ordinal value from port:index
GPIO_PORT() returns the port of an ordinal value
GPIO_INDEX() returns the index or offset of the ordinal.

Discussion on the mailing list at
	http://lists.denx.de/pipermail/u-boot/2012-January/116927.html

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-02-27 21:19:23 +01:00
Tom Rini
a7778f8fbe omap_hsmmc: Wait for CMDI to be clear
Before we can send a command we need both the DATI (command inhibit on
mmc_dat line) bit and CMDI (command inhibit on mmc_cmd line) are clear.
The previous behavior of only checking on DATI was insufficient on some
cards and incorrect behavior in any case.  This makes the code check
for both bits being clear and makes the error print more clear as
to what happened.  DATI_CMDDIS is removed as it was unused elsewhere
in the code and stood for 'DATI is set, cmds are disabled still'.

Fix originally spotted by Peter Bigot.

Tested-by: Peter A. Bigot <bigotp@acm.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Andreas Müller <schnitzeltony@googlemail.com>
2012-02-15 17:42:22 -06:00
Sughosh Ganu
6b873dcabd Changes to move hawkboard to the new spl infrastructure
This patch moves hawkboard to the new spl infrastructure from the
older nand_spl one.

Removed the hawkboard_nand_config build option -- The spl code now
gets compiled with hawkboard_config, after building the main u-boot
image, using the CONFIG_SPL_TEXT_BASE. Modified the README.hawkboard
to reflect the same.

Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
2012-02-12 10:11:33 +01:00
Peter Barada
9540c7e900 ARMV7: Fix duplicate use of "b" parameter in ACTIM_CTRLA definition
ACTIM_CTRLA macro errently passes "b" parameter to ACTIM_CTRLA_TRAS()
instead of "c".  To make usage more clear, replace all single-letter
macro parameters with more descriptive parameter names.

Signed-off-by: Peter Barada <peter.barada@logicpd.com>
2012-02-12 10:11:32 +01:00
Hadli, Manjunath
8f5d468721 davinci: add support for printing clock frequency
add support for printing various clock frequency info found
in SOC such as ARM core frequency, DSP core frequency and DDR
frequency as part of bdinfo command.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
2012-02-12 10:11:32 +01:00
Schuyler Patton
c8e5ba8034 AM3517: Changed default clock rate for AM3517
AM3517: Changed default clock rate for AM3517

Changed #define MPU_M_13_ES2 from 0x1F4 to 0x258, this allows
the AM3517 to boot up at 600MHz instead of 500 MHz

Signed-off-by: Schuyler Patton <spatton@ti.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
2012-02-12 10:11:31 +01:00
Govindraj.R
95f8791042 OMAP3+: Clock: Adding ehci clock enabling
Adding ehci clock enabling mechanism part of clock framework.
When essential clocks are enabled during init phase usb host
clocks can also be enabled from clock framework.

Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Stefano Babic <sbabic@denx.de>
2012-02-12 10:11:31 +01:00
Govindraj.R
43b62393da ehci-omap: Clean up added ehci-omap.c
Clean up added ehci-omap.c and make it generic for re-use across
omap-soc having same ehci ip block. Also pass the modes to be configured
from board file and configure the ports accordingly. All usb layers
are not cache aligned, till then keep cache off for usb ops as ehci will use
internally dma for all usb ops.

* Add a generic common header ehci-omap.h having common ip block
  data and reg shifts.
* Rename and modify ehci-omap3 to ehci.h retain only conflicting
  sysc reg shifts remove others and move to common header file.
* pass the board data for beagle/panda accordinly to use
  ehci ports.

Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
2012-02-12 10:11:31 +01:00
Chander Kashyap
37bb6d89de ARM: EXYNOS: Add support for Exynos5 based SoCs
Samsung's ARM Cortex-A15 based SoCs are known as Exynos5 series of
SoCs. This patch adds the support for Exynos5.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12 10:11:30 +01:00
Minkyu Kang
851db35e2d S5P: support generic watchdog timer
This patch adds support the generic watchdog timer for s5pc1xx and exynos4

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: HeungJun, Kim <riverful.kim@samsung.com>
2012-02-12 10:11:29 +01:00
HeungJun, Kim
77e490e225 ARMV7: Exynos4: Add supoort power for Exynos4
This patch adds power.h and SAMSUNG_BASE() macro for using Exynos4 power.

Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12 10:11:29 +01:00
HeungJun, Kim
792be0aa80 ARMV7: Exynos4: Add watchdog.h for Exynos4
This patch add watchdog.h for Exynos4

Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12 10:11:29 +01:00
Chander Kashyap
e619a0de93 Exynos: PWM: Add TCMPB3 field in pwm structure
Add TCMPB3 field in pwm structure, earliar this was res1.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12 10:11:28 +01:00
Albert ARIBAUD
805ad7ee2d orion5x: add USB host ehci-marvell support
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2012-02-12 10:11:28 +01:00
Albert ARIBAUD
74d3442111 Remove kirkwood-specifics from marvell EHCI driver
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2012-02-12 10:11:27 +01:00
Albert ARIBAUD
a14bd41738 Rename ehci-kirkwood as ehci-marvell
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2012-02-12 10:11:27 +01:00
Helmut Raiger
fa47a28661 mmc: access mxcmmc from mx31 boards
This patch modifies mxcmmc.c to be used
not only by i.MX27 but also by i.MX31 boards.
Both use the same SD controller, but have different
clock set-ups.
The i.MX27 imx_get_XXXclock functions are made static to
generic.c and a public mxc_get_clock() function
is provided.  Pins, base address and prototypes for
an i.MX31 specific board_init_mmc() are provided.
Some of the i.MX27 clock getters are unused and marked
as such to avoid warnings (./MAKEALL -s mx27), but
the code was left in for future use.

Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-02-12 10:11:26 +01:00
Troy Kisky
4591f523df i.mx6: mx6x_pins: Fix uart txd definitions
The uart txd pad can also provide the rxd function. But it does not stop its
tx role. This could be used for a half duplex serial port.

Change names to reduce confusion.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Jason Liu <jason.hui@linaro.org>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <jason.hui@linaro.org>
2012-02-12 10:11:26 +01:00
Heiko Schocher
2627c8c0a1 arm, davinci: add timer defines for tcr field
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <tom.rini@gmail.com>
2012-02-12 10:11:23 +01:00
Heiko Schocher
3f84108b99 arm, davinci: add workaround for not resetting DMA bus and VPSS modules
The Buffer Logic of VPSS is Not Reset by System Reset Pin, see
http://www.ti.com/lit/er/sprz316b/sprz316b.pdf chapter Advisory 1.2.1
on page 9. Add workaroundcode proposed in the errata.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <tom.rini@gmail.com>
2012-02-12 10:11:23 +01:00
Ben Gardiner
d652a344a0 arm, davinci: add PLL0 prediv to da850 lowlevel setup
The OMAP-L138 has a pre-divider available on PLL0.

Add support to da850_lowlevel.c for configuring PLL0's pre-divider. This is
to achieve certain OPP's -- e.g. the 372MHz OPP used also by Linux.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: Christian Riesch <christian.riesch@omicron.at>
CC: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
2012-02-12 10:11:22 +01:00
Simon Glass
cf06b13903 tegra: Add SDMMC support to funcmux
This adds support for SDMMC ports to the funcmux. Only one
option is supported: FUNCMUXO_SDMMC_8BIT which selects an 8-bit
wide SDIO interface where available.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12 10:11:22 +01:00
Simon Glass
8a1133c607 tegra: Add I2C support to funcmux
Add support to funcmux for selecting I2C functions and programming
the pinmux appropriately.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12 10:11:22 +01:00
Simon Glass
2faf1863de tegra: Add enum to select from available funcmux configs
We want to give a name to each available funcmux config. For now we just
use the pin group names (even through it is verbose) since there seems
to be nothing better.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12 10:11:22 +01:00
Simon Glass
d693969daa tegra: Adjust funcmux config test to permit expansion
We want to support config options other than zero, so move the test to the
end to allow intermediate code to OK such a config.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12 10:11:22 +01:00
Patil, Rachna
b4116ede36 ARM: AM33XX: Add i2c support
Add i2c driver board hookup for AM335X EVM

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Patil, Rachna <rachna@ti.com>
2012-01-23 11:57:31 +01:00
Andreas Müller
137703b811 overo: add SPL support
* implementation based on ti beagleboard/omap3evm
* timing data and i2c workaround for revision 0 boards taken from x-loader
* run-tested with overo revision 0 and 1 / boot from NAND and SDcard
* run-tested with x-loader

Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16 08:40:13 +01:00
Andreas Müller
761ca31e47 omap_rev_string: output to stdout
* avoid potential buffer overflows
* allow SPL-build not to output "Texas Instruments Revision detection unimplemented"

Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16 08:40:13 +01:00
Chandan Nath
8a8f084e4f ARM:AM33XX: Add SPL support for AM335X EVM
This patch is added to support SPL feature on AM335X
platform. In this patch, MMC1 is configured as boot
device for SPL and support for other devices will be
added in the next patch series.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16 08:40:12 +01:00
Chandan Nath
876bdd6d46 ARM:AM33XX: Add mmc/sd support
This patch add supports for mmc/sd driver on AM335X platform.
PLL and pinmux configurations for mmc/sd are configured in this
patch.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16 08:40:12 +01:00
Chandan Nath
fb072a3ead ARM:AM33XX: Fix ddr and timer register offset
This patch is added to update incorrect ddr and timer
register offset.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16 08:40:11 +01:00
Chandan Nath
f16da7466f ARM:AM33XX: Replace CONFIG_AM335X with CONFIG_AM33XX
This patch is added to replace CONFIG_AM335X symbol
with CONFIG_AM333XX for AM33XX platforms.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Thomas Weber <weber@corscience.de>
2012-01-16 08:40:11 +01:00
Aneesh V
fe7104b307 omap4: fix boot issue on ES2.0 Panda
Fix boot issue on ES2.0 Panda by tuning some
IO settings. The CONTROL_EFUSE_2 register has
to be over-ridden in software for 4430 boards.

Commit 23e9f0723e
wrongly did this for CONTROL_EFUSE_1. Reverting
this and doing it for CONTROL_EFUSE_2.

Signed-off-by: Aneesh V <aneesh@ti.com>
Tested-by: Raúl Porcel <armin76@gentoo.org>
2012-01-16 08:40:11 +01:00
Christian Riesch
a601bed065 arm, davinci: Change byte order of RTC kick register values
Now the values in the defines agree with those in the manuals.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
2012-01-16 08:40:10 +01:00