Subroutines in comphy_usb2_power_up() and comphy_sgmii_power_up() functions
may fail. In this case, do not continue execution of current function and
instead jump to the end. Return value in 'ret' variable is already set.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
phy_txd_inv or phy_rxd_inv needs to be set only in case when
appropriate polarity is inverted. Otherwise these bits should be
cleared.
Same change was included in TF-A project:
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/9406
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marvell Armada 3700 Functional Specifications, section 52.2 PCIe Link
Initialization says that TXDCLK_2X_SEL bit needs to be enabled for PCIe
Root Complex mode.
Same change was included in TF-A project:
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/9408
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
In commit b24bb99d cp110 configuration initially done in u-boot
was removed and delegated to atf firmware as smc call.
That commit didn't account for later introduced in d13b740c SATA invert polarity support.
This patch adds support of passing SATA invert polarity flags to atf
firmware during the smc call.
Signed-off-by: Denis Odintsov <shiva@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add additional step which enables the Impedance and PLL calibration.
- Enable old squelch detector instead of the new analog squelch detector
circuit and update host disconnect threshold value.
- Update LS TX driver strength coarse and fine adjustment values.
Change-Id: Ifa0a585bfb5ecab0bfa033eed6874ff98b16a7df
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
In CP115, comphy4 can be configured into SFI port1
(in addition to SFI0). This patch adds the option
described above.
In addition, rename all existing SFI/XFI references:
COMPHY_TYPE_SFI --> COMPHY_TYPE_SFI0
No functional change for exsiting configuration.
Change-Id: If9176222e0080424ba67347fe4d320215b1ba0c0
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
According to Design Reference Specification the PHY PLL and Calibration
register from PHY0 are shared for multi-port PHY. PLL control registers
inside other PHY channels are not used.
This commit reworks utmi device tree nodes in a way that common PHY PLL
registers are moved to main utmi node. Accordingly both child nodes
utmi-unit range is reduced and register offsets in utmi_phy.h are updated
to this change.
This fixes issues in scenarios when only utmi port1 was in use, which
resulted with lack of correct pll initialization.
Change-Id: Icc520dfa719f43a09493ab31f671efbe88872097
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
New products can contain up to 6 usb ports, therefore allow to initialize
all relevant UTMI PHYs.
Change-Id: I28c36e59fa0e3e338bb3ee0cee2240b923f39785
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
It helps ATF to determine who called power off
function (U-boot/Linux) and act accordingly
Change-Id: Icfc5cbfdba64754496812154272b28c0ff639f0f
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
- the default value of comphy pipe selector is set to PCIe (x4)
in case of unconnected comphy the default value remains 0x4
which may lead to several issues with comphy initialization.
- this patch adds SMC call that powers off the comphy lane in case of
unconnected comphy.
Change-Id: I196b2916518dd8df3b159ffa85e2989b8e483087
Signed-off-by: Christine Gharzuzi <chrisg@marvell.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Currently, we don't pass id for SGMII 0/1.
A bug in comphy selector configuration was found (in comphy
firmware), after fixing it, SGMII0/1 have different configuration,
so we need to pass the ID the firmware.
Change-Id: Idcff4029cc9cf018278e493221b64b33574e0d38
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Change-Id: I358792a96c13b54e700c05227cc7a8f6bd584694
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Now the comphy configuration is handled in atf, therefore there is no
need to configure phy or pipe selector in u-boot, it is configured by
atf for each particular pair: lane and mode.
Change-Id: I0bebf8d5ff66dbeb6bf9ef90876195938a8eb705
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Replace the XFI training with appropriate SMC call, so the firmware will
perform exact initialization.
Update Stefan 2021-03-23:
Move comphy_smc() function to an earlier place - necessary for the
mainline merge.
Change-Id: I789b130b05529dc80dadcf66aef407d93595b762
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Igal Liberman <igall@marvell.com>
Replace the comphy initialization for USB with appropriate SMC call,
so the firmware will execute required serdes configuration.
Change-Id: I7f773c0dfac70db9dd2653de2cdcfac577e78c4e
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Replace the comphy initialization for RXAUI with appropriate SMC call,
so the firmware will execute required serdes configuration.
Change-Id: Iedae0285fb283e05bb263a8b4ce46e8e7451a309
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Even if comphy types of SATA2/SATA3/SGMII3 and comphy speeds of
1.5G/3G/6.25G were referenced in the driver non configuration (dts)
was using it.
This patch removes unused definitions.
Change-Id: I53ed6f9d3a82b9d18cb4e488bc14d3cf687f9488
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
This patch adds support for running RX training using new command called
"rx_training"
Usage:
rx_training - rx_training <cp id> <comphy id>
RX training allows to improve link quality (for SFI mode)
by running training sequence between us and the link partner,
this allows to reach better link quality then using static configuration.
Change-Id: I818fe67ccaf19a87af50d4c34a9db7d6802049a5
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
This allows the lower level driver access to comphy map data
(required for RX training support, which is introduced
in the following patches).
Change-Id: Ib7ffdc4b32076c01c3a5d33f59552c9dfc6b12fa
Signed-off-by: Igal Liberman <igall@marvell.com>
If fdtdec_get_int can't find speed, set COMPHY_SPEED_INVALID
If fdtdec_get_int can't find type, set COMPHY_TYPE_INVALID
Move the error print if phy-type is invalid
Add continue to the probe loop (in a case of invalid phy)
Cosmetic changes
Change-Id: I0c61b40bfe685437426fe907942ed338b7845378
Signed-off-by: Igal Liberman <igall@marvell.com>
Add UTMI analog parameters initialization values according to
latest ETP.
Change-Id: I5bcca205a3995202a18ff126f371a81f69e205c8
Signed-off-by: Igal Liberman <igall@marvell.com>
UTMI should be initialized only for enabled device tree nodes.
This fix overrides current internal configuration array
entry with the next DT entry data if error is detected
during the current DT entry parsing or the current port
is disabled.
This way the internal configuration structure will only
contain valid ports information obtained from the DT.
Change-Id: I9c43c6a5d234e15ae9005d1c9bc983fc1f3544b8
Signed-off-by: Omri Itach <omrii@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
In get_speed_string() we have an array (speed_strings[])
which includes all possible speed strings.
This array size and content must be aligned to the speed
defines in comphy_data.h.
This patch adds missing 5.125G speed, aligns speed_strings[]
and fixes incorrect printing when speed > 5.0G.
Change-Id: I9900d23595094be321be0c62fcaa88036324568e
Signed-off-by: Igal Liberman <igall@marvell.com>
Currently, all comphy definitions are PHY_TYPE_XX and PHY_SPEEED_XX.
Those definition might be confused with MDIO PHY definitions.
This patch does the following changes:
- PHY_TYPE_XX --> COMPHY_TYPE_XX
- PHY_SPEED_XX --> COMPHY_SPEED_XX
This improves readability, no functional change.
Change-Id: I2bd1d9289ebbc5c16fa80f9870f797ea1bcaf5fa
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
- For some Marvell SoCs, like armada-3700, there are both
USB host and device controller, but on PHY level the
configuration is the same.
- The new type supports both USB device and USB host
- This patch is cherry-picked from u-boot-2015 as-is.
Change-Id: I01262027edd8ec23391cff6fb409b3009aedfbb9
Signed-off-by: jinghua <jinghua@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
It helps ATF to determine who called power on function (U-boot/Linux).
The corresponding ATF code was added in this commit:
mvebu: cp110: avoid pcie power on/off sequence when called from Linux
55df84f974
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Replace the comphy initialization for PCIe with appropriate SMC call, so
the firmware will perform appropriate comphy initialization.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Replace all comphy initialization with appropriate smc calls. It will
result with triggering synchronous exception that is handled by Secure
Monitor code in EL3. Then the Secure Monitor code will dispatch each smc
call (by parsing the smc function identifier) and triggers appropriate
comphy initialization.
This patch reworks serdes handling for: SATA, SGMII, HS-SGMII and SFI
interfaces.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
- This patch moves sata phy powerup from dedicate phy to compphy
and adds invert option for sata powerup routine.
Change-Id: I1b4e8753e2b2c14c6efa97bca2ffc7d2553d8a90
Signed-off-by: zachary <zhangzg@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/53601
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: Igal Liberman <igall@marvell.com>
[a.heider: adapt to mainline]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This patch adds support to Armada 7k/8k comphy RX/TX lane swap. The
'phy-invert' DT property defines the inverted signals.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This adds a weak definition of comphy_update_map to comphy_core,
which does nothing. If this function is defined elsewhere, for example
in board file, the board file can change some parameters of SERDES
configuration.
This is needed on Turris Mox, where the SERDES speed on lane 1 has to
be set differently when SFP module is connected and when Topaz Switch
module is connected.
This is a temporary solution. When the comphy driver for armada-3720
will be added to the kernel, the comphy driver in u-boot shall also be
updated and this should be done differently then.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The DTS file for armada-37xx uses the string "marvell,armada3700-ehci",
but the code searched for "marvell,armada-3700-ehci".
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Move the reg_set* functions into comphy.h as static inline functions.
Change return type of get_*_string to const char *.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
In SGMII initialization PIN_PIPE_SEL has to be zero when resetting
the PHY. Since comphy_mux already set the selector register to
correct values, we have to store it's value before setting it to 0
and restore it after SGMII init.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Lane 0 supports SGMII1 and USB3.
Lane 1 supports SGMII0 and PEX0.
Lane 2 supports SATA0 and USB3.
This is needed for Armada 37xx.
This introduces new device tree bindings. AFAIK there is currently no
driver for Armada 37xx comphy in Linux. When such a driver will be
pushed into Linux, this will need to be rewritten accordingly.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The register addresses on lanes 0 and 1 are switched, first comes 1 and
then 0.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently comphy_mux supports only trivial order of nodes in pin
selector register, that is lane N on position N*bitcount.
Add support for nontrivial order, with map stored in device tree
property mux-lane-order.
This is needed for Armada 37xx.
As far as I know, there is no driver for Armada 37xx comphy in the
kernel. When such a driver comes, this will need to be rewritten to
support the device tree bindings from the kernel.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit is based on commit d9899826 by
zachary <zhangzg@marvell.com>
from u-boot-marvell, see
github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/d9899826
- According to design specification, the transmitter should be set to high
impedence mode during electrical idle. Thus transmitter should detect RX
at high impedence mode also, and delay is needed to accommodate high
impedence off latency. Otherwise the USB3 will have detection issue that
most of the time the USB3 device can not be detected at all, or be
detected as USB2 device sometimes.
Modified registers: RD005C302h (R181h) (0051h) Lane Configuration 1
Bit 6: set to 1 to let Tx detect Rx at HiZ mode
Bit [3:4]: set to 2 to be delayed by 2 clock cycles
Bit 0: set to 1 to set transmitter to high impedance mode during idle.
- USB3 De-emphasize level of -3.5dB is mandatory, but USB3 MAC selects 0x2
(emphasize disabled) in the MAC_PHY_TXDEEMPH [1:0], while it is supposed
to select 0x1(3.5dB emphasize). Thus need to override what comes from
the MAC(by setting register 0x1c2 bit2 to 0x1) and to configure the
overridded values of MAC_PHY_TXDEEMPH [1:0] to 0x1(bit15 of register
0x181 and bit0 of register 0x180).
- According to USB3 application note, need to update below comphy
registers:
Set max speed generation to USB3.0 5Gbps(set RD005C04Ah bit[11:10] to 1)
Set capacitor value to 0xF(set RF005C224 bit[3:0] to 0xF)
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
