Add an option to indicate that the video driver should setup a SimpleFB
node that passes the video framebuffer initialized by U-Boot to the
operating system kernel.
Currently only the Allwinner DE driver uses this option, and the
definition of this option in the sunxi-common.h config header is
converted to an imply of this option from CONFIG_VIDEO_SUNXI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The sunxi DE1 video option used to be CONFIG_VIDEO, which has the same
name as the "Enable legacy video support" option in
drivers/video/Kconfig.
Change the option name to CONFIG_VIDEO_SUNXI, which is really used by
Makefile under drivers/video/sunxi/, and defined in sunxi-common.h
when CONFIG_VIDEO is selected before this change. Now CONFIG_VIDEO_SUNXI
selects CONFIG_VIDEO and the usages of CONFIG_VIDEO in sunxi Kconfig and
config headers are all converted to use CONFIG_VIDEO_SUNXI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
All the new SoCs from Allwinner since the A33 have had the phy_ctl offset
at 0x410 instead of 0x404 that was used on the previous SoCs.
Instead of adding more and more special cases as the number of SoCs grow,
let's invert the test to have 0x410 by default, and the (hopefully) fixed
number of old SoCs being the exception.
Suggested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
U-Boot itself might need to identify the boot device, for example to be
able to tell where to load the kernel from when several options are
possible.
Move the logic of spl_boot_device to a function that is compiled both for
the SPL and the main binary.
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The eMMC controller for the A83T uses the new operating mode. Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
At present we support multiple environment drivers but there is not way to
select between them at run time. Also settings related to the position and
size of the environment area are global (i.e. apply to all locations).
Until these limitations are removed we cannot really support more than one
environment location. Adjust the location to be a choice so that only one
can be selected. By default the environment is 'nowhere', meaning that the
environment exists only in memory and cannot be saved.
Also expand the help for the 'nowhere' option and move it to the top since
it is the default.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Move all of the imply logic to default X if Y so it works again]
Signed-off-by: Tom Rini <trini@konsulko.com>
With SPL_LDSCRIPT moved to Kconfig (and this being a 'string' config
node), all the lingering definitions in header files will cause
warnings/errors due to the redefinition of the configuration item.
As we don't want to pollute the defconfig files (and values should
usually be identical for entire architectures), the defaults are moved
into Kconfig. Kconfig will always pick the first default that
matches, so please keep these values at the end of each file (to allow
any board-specific Kconfig, which will be included earlier) to
override with an unconditional default setting.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The PRCM of H3/H5 SoCs have a secure/non-secure switch, which controls
the access to some clock/power related registers in PRCM.
Current Linux kernel will access the CPUS (AR100) clock in the PRCM
block, so the PRCM should be switched to non-secure.
Add code to switch the PRCM to non-secure.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE
In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.
In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.
There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with
./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC
And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
As we added LPDDR3 support in the former patch, we need a set of timing
info to really enable it.
Add the timing info used by stock boot0.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Some A64 boards (SoPine and Pinebook production batch) use LPDDR3 DRAM
chips.
Add support for LPDDR3 DRAM in the DesignWare-like DRAM controller code.
Real LPDDR3 chips' support is not added yet in this commit.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
As we have already support for the DesignWare DRAM controller and the
integrated DDR2 chip of V3s, let's enable the SPL support for V3s.
This patch also contains the default DRAM configuration for V3s.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner V3s features a DRAM controller like the on in H3, but with a
DDR2 DRAM.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner V3s SoC features a co-packaged DDR2 DRAM chip, which needs its
timing param.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The DesignWare-like DRAM code used to set the controller defaultly to
single rank mode, which makes it not able to detect the second rank.
Set the default value to dual rank, thus the rank detection code can
work and finally the rank setting will be the correct value.
Currently we know little about the dual-rank on R40, and the usage
of A15 address line seems to be breaking dual-rank support. The only R40
board currently available (Sinovoip Banana Pi M2 Ultra) uses A15 rather
than dual-rank, thus we cannot do research for it. So dual rank detection
is temporarily disabled on R40.
This change is tested on a Orange Pi One (H3, single rank), a Pine64+
2GiB version (A64, single rank) , a Pinebook early prototype with DDR3
(A64, dual rank) and a SoPine with some LPDDR3 patch (A64, dual CS pins
on one chip).
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
DRAM chip varies, and one code cannot satisfy all DRAMs.
Add options to select a timing set.
Currently only DDR3-1333 (the original set) is added into it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Some DDR2 DRAM have only four banks, not eight.
Add code to detect this situation.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Some Allwinner SoCs features a DesignWare-like controller with only 16
bit bus width.
Add support for them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The DesignWare DRAM controller used by H3 and newer SoCs use a bit to
identify whether the DRAM is half-width.
As H3 itself come with 32-bit DRAM, the two modes of the bit used to be
named "MCTL_CR_32BIT" and "MCTL_CR_16BIT", but for SoCs with 16-bit DRAM
they're really 8-bit and 16-bit.
Rename the bit's macro, and also rename the variable name in
dram_sun8i_h3.c.
This commit do not add 16-bit DRAM controller support, but the support
will be introduced in next commit.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner SoCs after H3 (e.g. A64, H5, R40, V3s) uses a H3-like
DesignWare DRAM controller, which do not have official free DRAM
initialization code, but can use modified dram_sun8i_h3.c.
Add a invisible option for easier DRAM initialization code reuse.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner SoCs with 64-bit cores use an ARM Trusted Firmware binary,
which needs to be loaded alongside U-Boot proper.
Set the respective Kconfig options to let them select this feature and
also automatically build the FIT image.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Rename Kconfig path to arch/arm/mach-sunxi/Kconfig]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
R40 has a similar SATA controller with the ones on A10/A20, but with a
reset line added (like other peripherals on sun6i+), and two extra VDD
pins added (1.2v and 2.5v).
Add clock configuration of R40 SATA.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
For the consistent location of SoC-level Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit adds support for DM I2C on sunxi platform. It can coexist
with old style sunxi I2C driver, because it is still used in SPL and
by some SoCs.
Because sunxi platform doesn't yet support DM clk, reset and pinctrl
driver, workaround is needed to enable clocks and set resets and
pinctrls. This is done by calling i2c_init_board() in board_init().
This means that CONFIG_I2Cx_ENABLE options needs to be correctly set
in order to use needed I2C controller.
Commit is based on the previous patch made by Philipp Tomsich
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Basic U-Boot support is now present for V3s.
Some memory addresses are changed specially for V3s, as the original
address map cannot fit into a so small DRAM.
As the DRAM controller code needs a big refactor, the SPL support is
disabled in this version.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is needed for HDMI, which will be added later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 seems to have a variant of the memory controller found in
the H3 and A64 SoCs. Adapt the code for use on the R40. The changes
are based on released DRAM code and comparing register dumps from
boot0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
According to the BSP released by Banana Pi, the R40 (sun8iw11p1) has
an extra "PLL lock control" register in the CCU, which controls whether
the individual PLL lock status bits in each PLL's control register work
or not.
This patch enables it for all the PLLs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The watchdog found on the R40 SoC is the older variant found on the A20.
Add the proper "#if defines" to make it work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 SoC uses the AXP221s in I2C mode to supply power.
Some regulator's common usages have changed, and also the recommended
voltage for existing usages have changed. Update the defaults to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 is the successor to the A20. It is a hybrid of the A20, A33
and the H3.
The R40's PIO controller is compatible with the A20,
Reuse the A20 UART and I2C muxing code by adding the R40's macro.
The display pipeline is the newer DE 2.0 variant.
Block enabling video on R40 for now.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner H5 Soc is bascially an H3 with high SRAM and ARMv8 cores.
As the peripherals and the pinmuxing are almost identical, we piggy
back on the shared MACH_SUN8I_H3_H5 config symbol.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The DRAM controller in the Allwinner H5 SoC is again very similar to
the one in the H3 and A64.
Based on the existing socid parameter, add support for this controller
by reusing the bulk of the code and only deviating where needed.
These new bits set or cleared here and there have been mostly found by
looking at DRAM register dumps after using the H5 boot0 and comparing
them to what we set in the code. So for now it's mostly unclear what
those bits actually mean - hence the missing names and comments.
Also add the delay line parameters taken from the boot0 and libdram
disassembly.
Register setup differences between H5 and H3 are courtesy of Jens Kuske.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Every armv8 board needs the memory map, so change the #ifdef to
ARM64 to avoid enumerating every single board or SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Instead of enumerating all SoC families that need that bit set, let's
just express this more clearly: The SMP bits needs to be set on
SMP capable ARMv7 CPUs. It's much easier in Kconfig to express it the
other way round, so we use ! CPU_IS_UP and ! ARM64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
If we take the liberty to use register r0 to perform our bit set, we
should be nice enough to tell the compiler about it.
Add r0 to the clobber list to avoid potential mayhem.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Now that the SPL is ready to be compiled in AArch64 and the DRAM
init code is ready, enable SPL support for the A64 SoC and in the
Pine64 defconfig.
For now we keep the boot0 header in the U-Boot proper, as this allows
to still use boot0 as an SPL replacement without hurting the SPL use
case.
We disable FEL support for now by making its compilation conditional
and disabling it for ARM64, as the code isn't ready yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Fix the output of the DRAM size on AArch64 SPLs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
According to Jens disabling the on-die-termination should set bit 5,
not bit 1 in the respective register. Fix this.
Reported-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The A64 DRAM controller is very similar to the H3 one,
so the code can be reused with some small changes.
This refactoring does not change the code size for the existing H3 part.
[Andre: rework from #ifdefs to using socid parameters in static
functions, minor fixes, merging in fixes from Jens]
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
So far the DRAM driver for the H3 SoC (and apparently boot0/libdram as
well) only applied coarse delay line settings, with one delay value for
all the data lines in each byte lane and one value for the control lines.
Instead of setting the delays for whole bytes only allow setting it for
each individual bit. Also add support for address/command lane delays.
For the purpose of this patch the rules for the existing coarse settings
were just applied to the new scheme, so the actual register writes don't
change for the H3. Other SoCs will utilize this feature later properly.
With a stock GCC 5.3.0 this increases the dram_sun8i_h3.o code size from
2296 to 2344 Bytes.
[Andre: move delay parameters into macros to ease later sharing, use
defines for numbers of delay registers, extend commit message]
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The IOCR registers got renamed to BDLR to match the public
documentation of similar controllers.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
So far the MBUS priority setup was done by writing "magic" values taken
from a DRAM controller register dump after a boot0 run.
By peeking at the Linux (sic!) MBUS driver [1] from the Allwinner BSP
kernel, we learned more about the actual meaning of those bits.
Add macros and refactor the setup function to make the MBUS setup much
more readable and meaningful.
The actual values used now are a transformation of the values used
before, which are assembled by the new code to result in the same register
writes. So this rework does not change any settings, also the code size
stays the same.
The respective source files in the BSP kernel had a proper GPL header,
so lifting this code and information into U-Boot is legal.
[Andre: provide a convenience macro to fit definitions on one line]
[1] https://github.com/longsleep/linux-pine64/blob/lichee-dev-v3.10.65/drivers/bus/sunxi_mbus.c
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Allwinner A64 SoC starts execution in AArch32 mode, and both
the boot ROM and Allwinner's boot0 keep running in this mode.
So U-Boot gets entered in 32-bit, although we want it to run in AArch64.
By using a "magic" instruction, which happens to be an almost-NOP in
AArch64 and a branch in AArch32, we differentiate between being
entered in 64-bit or 32-bit mode.
If in 64-bit mode, we proceed with the branch to reset, but in 32-bit
mode we trigger an RMR write to bring the core into AArch64/EL3 and
re-enter U-Boot at CONFIG_SYS_TEXT_BASE.
This allows a 64-bit U-Boot to be both entered in 32 and 64-bit mode,
so we can use the same start code for the SPL and the U-Boot proper.
We use the existing custom header (boot0.h) functionality, but restrict
the existing boot0 header reservation to the non-SPL build now. A SPL
wouldn't need such header anyway. This allows to have both options
defined and lets us use one for the SPL and the other for U-Boot proper.
Also add arch/arm/mach-sunxi/rmr_switch.S, which contains the original
ARM assembly code and instructions how to re-generate the encoded
version.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
These days many Allwinner SoCs use clock_sun6i.c, although out of them
only the (original sun6i) A31 has a second MBUS clock register.
Also the requirement for setting up the PRCM PLL_CTLR1 register to provide
the proper voltage seems to be a property of older SoCs only as well.
Restrict the MBUS initialization to this SoC only to avoid writing bogus
values to (undefined) registers in other chips.
I can only verify that the PLL voltage setup is not needed for H3 and
A64, so for now we only spare those two SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
H3 SID controller has some bug, which makes the initial SID value at
SUNXI_SID_BASE wrong when boot.
Change the SID retrieve code to call the SID Controller directly on H3,
which can get the correct value, and also fix the SID value at
SUNXI_SID_BASE, so that it can be used by further operations.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
It is useful to name each method so that we can print out this name when
using the method. Currently this happens using a separate function. In
preparation for unifying this, add a name to each method.
The name is only available if we have libcommon support (i.e can use
printf()).
Signed-off-by: Simon Glass <sjg@chromium.org>
This is a cleaned up version set_pll() from Allwinner's boot0 source
(bootloader/basic_loader/bsp/bsp_for_a80/common/common.c).
[wens@csie.org: Added commit message; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Since the A80 has many cores which we intend to use in SMP fashion,
we should set the SMP bit for the boot CPU.
[wens@csie.org: Added commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On sun9i, the GTBUS manages transaction priority and bandwidth
for multiple read ports when accessing DRAM. The initialisation
mirrors the settings from Allwinner's boot0 for now, even though
this may not be optimal for all applications (e.g. headless
systems might want to give priority to IO modules).
Adding a common callout to gtbus_init() from the SPL clock init
with a weakly defined implementation in sunxi/clock.c to fallback
to for platforms that don't require this.
[wens@csie.org: Moved gtbus_sun9i.c to arch/arm/mach-sunxi/; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This adds DRAM initialisation code for sun9i, which calculates the
appropriate timings based on timing information for the supplied
DDR3 bin and the clock speeds used.
With this DRAM setup, we have verified DDR3 clocks of up to 792MHz
(i.e. DDR3-1600) on the A80-Q7 using a dual-channel configuration.
[wens@csie.org: Moved dram_sun9i.c to arch/arm/mach-sunxi/; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[hdegoede@redhat.com: Drop some huge non-documenting #if 0 ... #endif blocks]
[hdegoede@redhat.com: Fix checkpatch warnings]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Mostly by adding MACH_SUN50I to some existing #ifdefs enable support
for the the HCI0 USB host controller on the A64.
Fix up some minor 64-bit hiccups on the way.
Add the bare minimum DT bits to the A64 .dtsi and enable the controllers
and the PHY on the Pine64.
This is limited to the first USB controller at the moment, which is
connected to the lower USB socket on the Pine64 board.
[Andre: remove unneeded defines, enable OHCI, add commit message]
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
H3 seems to have a silicon bug breaking the impedance calibration.
This is currently worked around in software by multiple steps
combining the results to replace the wrong values.
Revision A chips need a different workaround, which is present in
the vendor bootloader too, but got overlooked in lack of
information and affected boards till now.
This commit adds a simplified version without correction factor,
which would be 1.00 for all known boards anyway.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Rather than having a global variable, pass the spl_image as a parameter.
This avoids BSS use, and makes it clearer what the function is actually
doing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code. Update existing users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present some spl_xxx_load_image() functions take a parameter and some
don't. Of those that do, most take an integer but one takes a string.
Convert this parameter into a struct so that we can pass all functions the
same thing. This will allow us to use a common function signature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Linux kernel musb driver expects VBUS to be off while initializing
musb. Having it on results in a repeating string of warnings, followed
by an unusable peripheral. The peripheral is only usable after
physically removing the OTG adapter, letting musb reset its state.
This partially reverts commit c9f8947e66 ("sunxi: usb-phy: Never
power off the usb ports")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The H3 PLL5 used for DRAM barely manages to lock to the required
frequency before DRAM controller starts, sometimes leading to wrong
delay-line calibration results.
This patch changes the PLL tuning parameters to the same values as
boot0 used, which speeds up the locking and fixes the problem.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
As part of testing booting Linux kernels on Rockchip devices, it was
discovered by Ziyuan Xu and Sandy Patterson that we had multiple and for
some cases incomplete isb definitions. This was causing a failure to
boot of the Linux kernel.
In order to solve this problem as well as cover any corner cases that we
may also have had a number of changes are made in order to consolidate
things. First, <asm/barriers.h> now becomes the source of isb/dsb/dmb
definitions. This however introduces another complexity. Due to
needing to build SPL for 32bit tegra with -march=armv4 we need to borrow
the __LINUX_ARM_ARCH__ logic from the Linux Kernel in a more complete
form. Move this from arch/arm/lib/Makefile to arch/arm/Makefile and add
a comment about it. Now that we can always know what the target CPU is
capable off we can get always do the correct thing for the barrier. The
final part of this is that need to be consistent everywhere and call
isb()/dsb()/dmb() and NOT call ISB/DSB/DMB in some cases and the
function names in others.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Sandy Patterson <apatterson@sightlogix.com>
Reported-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reported-by: Sandy Patterson <apatterson@sightlogix.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce virtual and physical addresses in the mapping table. This change
have no impact on existing boards because they all use idential mapping.
Signed-off-by: York Sun <york.sun@nxp.com>
Now that we know that the BROM stores a value indicating the boot-source
at the beginning of SRAM, use that instead of trying to recreate the
BROM's boot probing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Allwinner devices support SPI flash as one of the possible
bootable media type. The SPI flash chip needs to be connected
to SPI0 pins (port C) to make this work. More information is
available at:
https://linux-sunxi.org/Bootable_SPI_flash
This patch adds the initial support for booting from SPI flash.
The existing SPI frameworks are not used in order to reduce the
SPL code size. Right now the SPL size grows by ~370 bytes when
CONFIG_SPL_SPI_SUNXI option is enabled.
While there are no popular Allwinner devices with SPI flash at
the moment, testing can be done using a SPI flash module (it
can be bought for ~2$ on ebay) and jumper wires with the boards,
which expose relevant pins on the expansion header. The SPI flash
chips themselves are very cheap (some prices are even listed as
low as 4 cents) and should not cost much if somebody decides to
design a development board with an SPI flash chip soldered on
the PCB.
Another nice feature of the SPI flash is that it can be safely
accessed in a device-independent way (since we know that the
boot ROM is already probing these pins during the boot time).
And if, for example, Olimex boards opted to use SPI flash instead
of EEPROM, then they would have been able to have U-Boot installed
in the SPI flash now and boot the rest of the system from the SATA
hard drive. Hopefully we may see new interesting Allwinner based
development boards in the future, now that the software support
for the SPI flash is in a better shape :-)
Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option
in a board defconfig, then building U-Boot and finally flashing
the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with
a help of the sunxi-fel tool:
sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin
The device needs to be switched into FEL (USB recovery) mode first.
The most suitable boards for testing are Orange Pi PC and Pine64.
Because these boards are cheap, have no built-in NAND/eMMC and
expose SPI0 pins on the Raspberry Pi compatible expansion header.
The A13-OLinuXino-Micro board also can be used.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.
The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant]
Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>
This addresses a cosmetic issue when booting a sunxi device
over USB (FEL mode), where the SPL currently would just print
"Trying to boot from ". The patch fixes that to properly read
"Trying to boot from FEL".
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A80 uses the AXP809 as its primary PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit bfb33f0bc4 ("sunxi: mctl_mem_matches: Add missing memory
barrier") broke compilation for the Pine64, as dram_helper.c now
includes <asm/armv7.h>, which does not compile on arm64.
Fix this by moving all barrier instructions into a separate header
file, which can easily be shared between arm and arm64.
Also extend the inline assembly to take the "sy" argument, which is
optional for ARMv7, but mandatory for v8.
This fixes compilation for 64-bit sunxi boards (Pine64).
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
We are running with the caches disabled when mctl_mem_matches gets called,
but the cpu's write buffer is still there and can still get in the way,
add a memory barrier to fix this.
This avoids mctl_mem_matches always returning false in some cases, which
was resulting in:
U-Boot SPL 2015.07 (Apr 14 2016 - 18:47:26)
DRAM: 1024 MiB
U-Boot 2015.07 (Apr 14 2016 - 18:47:26 +0200) Allwinner Technology
CPU: Allwinner A23 (SUN8I)
DRAM: 512 MiB
Where 512 MiB is the right amount, but the DRAM controller would be
initialized for 1024 MiB.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Some boards have on board usb devices which need longer than the USB
spec's 1 second to connect from board powerup. Add a config option which
when non 0 adds an extra delay before the first usb bus scan.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Allwinner A64 SoC is used in the Pine64. This patch adds
all bits necessary to compile U-Boot for it running in AArch64
mode.
Unfortunately SPL is not ready yet due to legal problems, so
we need to boot using the binary boot0 for now.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: remove SPL code, move to AArch64]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some parts of the sunxi code cast explicitly between u32 values and pointers.
This is not a problem in practice, because all 64bit SoCs today only use the
lower 32 bits for their phyical address space. But we need to make sure that
the compiler is sure this is not an accident as well.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some of the code in arch/arm/cpu/armv7/sunxi is actually armv7 specific, while
most of it is just generic code that could as well be used on an AArch64 SoC.
Move all files that are not really tied to armv7 into a new mach-sunxi
directory.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
