We do not have a need to share a single console with the evaluation
board and disabling this option reduces the complexity of configuring
the consoles. Disable CONSOLE_MUX
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Rename SPL_MTD_SUPPORT to SPL_MTD in order to match MTD. This allows using
CONFIG_IS_ENABLED to test for MTD support.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
K3 devices have runtime type board detection. Make the default defconfig
include the secure configuration. Then remove the HS specific config.
Non-HS devices will continue to boot due to runtime device type detection.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
We like to put the SPL first so it is clear that it relates to SPL. Rename
various malloc-related options which have crept in, to stick to this
convention.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
This is used when building the FIT image configuration string. Enable
it for all FIT using TI platforms.
Signed-off-by: Andrew Davis <afd@ti.com>
[ extend to other k3 boards ]
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The MSMC fixup is something we do based on SoC, not based on the board.
So this fixup does not belong in the board files. Move this to the
mach-k3 common file so that it does not have to be done in each board
that uses these SoCs.
We use ft_system_setup() here instead of ft_board_setup() since it is no
longer board level. Enable OF_SYSTEM_SETUP in the configurations that use
this to keep functionality the same.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The fdt_path_offset() function is slow since it must scan the tree.
This substantial overhead now applies to all boards.
The original code may not be ideal but it is fit for purpose and is only
needed on a few boards.
Reverting this reduces time to set up driver model by about 30ms.
Before revert:
Accumulated time:
47,170 dm_r
53,237 dm_spl
572,986 dm_f
Accumulated time:
44,598 dm_r
50,347 dm_spl
549,133 dm_f
This reverts commit 26f981f295.
Signed-off-by: Simon Glass <sjg@chromium.org>
The first AM6x device was the AM654x, but being the first we named it
just AM6, since more devices have come out with this same prefix we
should switch it to the normal convention of using the full name of the
first compatibility device the series. This makes what device we are
talking about more clear and matches all the K3 devices added since.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adding the SPL_USB_DWC3_GENERIC symbol broke some ti builds. This
should fix the builds but untested on HW.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Asking if the alias we found actually points at the device tree node
we passed in (in the guise of its offset from blob) can be done simply
by asking if the fdt_path_offset() of the alias' path is identical to
offset.
In fact, the current method suffers from the possibility of false
negatives: dtc does not necessarily emit a phandle property for a node
just because it is referenced in /aliases; it only emits a phandle
property for a node if it is referenced in <angle brackets>
somewhere. So if both the node we passed in and the alias node we're
considering don't have phandles, fdt_get_phandle() returns 0 for both.
Since the proper check is so simple, there's no reason to hide that
behind a config option (and if one really wanted that, it should be
called something else because there's no need to involve phandle in
the check).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Aswath Govindraju <a-govindraju@ti.com>
This converts the following to Kconfig:
CONFIG_SYS_SPL_MALLOC_SIZE
CONFIG_SYS_SPL_MALLOC_START
We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to
control if we have a malloc pool or not.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FS_LOAD_KERNEL_NAME
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
Signed-off-by: Tom Rini <trini@konsulko.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Swap out the TI-centric "envboot" logic for the generic distro_bootcmd
logic for the bootcmd we run before trying to do something more complex
involving additional firmware, etc.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210713141139.15183-1-trini@konsulko.com
Currently the config options CONFIG_SYS_DFU_DATA_BUF_SIZE and
CONFIG_SYS_DFU_MAX_FILE_SIZE are being set in include/configs/<board>.h
files and also in <board_name>_defconfig files without a Kconfig option. It
is easier for users to set these configs in defconfig files than in config
header files as they are a part of the source code.
Add Kconfig symbols, and update the defconfigs by using tools/moveconfig.py
script.
Suggested-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Add configs for voltage switching and UHS modes for the SD card
and HS200 for the eMMC.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
AM65x SoC has two USB subsystems and their corresponding device tree nodes
have the same name but different path. While allocating sequence numbers
for these device tree nodes using alias, phandles can be used to
distinguish them.
Enable config for phandle check while getting sequence number to
distinguish the USB device tree nodes.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
By default CONFIG_LOGLEVEL seems to be set to 4 which is
too low and doesn't show dev_info/dev_notice/dev_warn
messages on console. This has been deliberately set low
globally to be conservative setting across the board due to
primary bootloader size limitations. It is best to tune
per board config as per user needs.
On K3 we have separate SPL and u-boot configs so we
can afford to set u-boot CONFIG_LOGLEVEL to 7.
On AM65 this patch causes u-boot.img size to change from
932KB to 940KB with 1 line additional print during
MMC boot. i.e. details of Net subsystem
"Net: K3 CPSW: nuss_ver: 0x6BA00102 cpsw_ver: 0x6BA80102 ale_ver: 0x00293904 Ports:1 mdio_freq:1000000"
Similar 8KB difference was seen on J721E.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
