Set number of lanes and link width speed control register based on the
num-lanes property.
Code imported almost 1:1 from dw_pcie_setup in mainline linux.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
+ ae350: modify memory layout and target name
+ ae350: use generic RISC-V timer driver in S-mode
+ Support bootstage report for RISC-V
+ Support C extension exception command for RISC-V
+ Add Starfive timer support
When setting up boot media to load the TIFS binary in legacy boot flow
(followed by J721E), get_timer() is called which calls dm_timer_init()
which then gets the tick-timer: mcu_timer0. mcu_timer0 uses k3_clks
(clock controller) and k3_pds (power controller) from the dmsc node that
forces probe of the ti_sci driver of TIFS that hasn't been loaded yet!
Running ti_sci_cmd_get_revision from the probe leads to panic since no
TIFS and board config binaries have been loaded yet. Resolve this by
moving ti_sci_cmd_get_revision to ti_sci_get_handle_from_sysfw as a
common point of invocation for both legacy and combined boot flows.
Before doing this, it is important to go through whether any sync points
exist where revision is needed before ti_sci_get_handle_from_sysfw is
invoked. Going through the code along with boot tests on both flows
ensures that there are none.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
_ alignment with kernel DT v6.5 for stm32f429 and stm32f746
_ rework way of displaying ST logo for stm32f746-disco and stm32f769-disco
STM32 MPU:
_ alignment with kernel DT v6.6-rc1
_ add RNG support for stm32mp13
_ add USB, USB boot and stm32prog command support for stm32mp13
_ add support of USART1 clock for stm32mp1
_ only print RAM and board code with SPL_DISPLAY_PRINT flag for
stm32mp1
_ rename update_sf to dh_update_sd_to_sf and add dh_update_sd_to_emmc
for stm32mp15xx DHCOR
-----BEGIN PGP SIGNATURE-----
iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmUdaJccHHBhdHJpY2Uu
Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/ptHxEACdibF5EoRb40qhQCWB
mwW50s76xWOyHGOGjSe3l18zxPdBjQ+9rnT8/A+mjaa8he4kMX9EZJyYRogcz7eR
QcnSeu9Q4L8bKbqnPBOpKF6TN7rFOIUcu+BWp3o8jZ+7/q7OSJrVLsjbXtCuCLnB
q5Pie/in7hmHJsQr6LJ4r31chW6Zm4VDuFiXquuxyE/c94Q8Ue27ag1/RfXL8b/g
Ir9aO+PAldGnVdnhPz4e6PZhzMfCVafw+DR7GVx3Zfnx2bg/dajo38UaLBDdEIS1
EIKONU2CBT/W1kPkLFiz+NdaYCzK9EL+RIbN/iG7ms+ds1+wc3zXpWwqZFASfIod
ZF788Up+wW+3SrKI2ySFjhQroNzDascn+bbHm4yJuAsORqY0XkxjSuWcSz++q8Hs
eMTw/R4uMfEiDvN1A7xlhBMuBrBHk4/6bdCRx2R6nkWes542fsgjXy8tGRWyUgnY
nbpTfYU07N8ck6arZ36KThedD7whJHHRcBYtLjhRG+lKbD0epWy67pXgTr9edTLf
U6ddH+Tndn4qhx067VhZ8vEXTCzypt4lY61MLcM0b9z8S1nJDn8b8jmiii7IR76L
/ocXzuLvNWHfmwNnB2hj/YY+n78vlZhegUxL5/6sH9lNebnewyEzCkVENNELUSYf
8M6vEZprvuhN44Z6hBUWZxXk0w==
=1mUx
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20231004' of https://source.denx.de/u-boot/custodians/u-boot-stm
STM32 MCU:
_ alignment with kernel DT v6.5 for stm32f429 and stm32f746
_ rework way of displaying ST logo for stm32f746-disco and stm32f769-disco
STM32 MPU:
_ alignment with kernel DT v6.6-rc1
_ add RNG support for stm32mp13
_ add USB, USB boot and stm32prog command support for stm32mp13
_ add support of USART1 clock for stm32mp1
_ only print RAM and board code with SPL_DISPLAY_PRINT flag for
stm32mp1
_ rename update_sf to dh_update_sd_to_sf and add dh_update_sd_to_emmc
for stm32mp15xx DHCOR
[ Fix merge conflict at board/st/common/stm32mp_dfu.c ]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add USART1 clock parents and mux configuration. This allows
support for configuring the USART1 as the serial console in
SPL and U-Boot via device tree. Without this patch the SPL
with usart1 serial console enabled crashes because it can
not find the clock specified in the device tree for usart1.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Ensure that the RAM configuration line is only printed when
CONFIG_SPL_DISPLAY_PRINT is set.
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
STM32 RNG configuration should best fit the requirements of the
platform. Therefore, put a platform-specific RNG configuration
field in the platform data. Default RNG configuration for STM32MP13
is the NIST certified configuration [1].
While there, fix and the RNG init sequence to support all RNG
versions.
[1] https://csrc.nist.gov/projects/cryptographic-module-validation-program/entropy-validations/certificate/53
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Seed errors can occur when using the hardware RNG. Implement the
sequences to handle them. This avoids irrecoverable RNG state.
Try to conceal seed errors when possible. If, despite the error
concealing tries, a seed error is still present, then return an error.
A clock error does not compromise the hardware block and data can
still be read from RNG_DR. Just warn that the RNG clock is too slow
and clear RNG_SR.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In order to ensure a good RNG quality and compatibility with
certified RNG configuration, add RNG clock frequency restraint.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
RNG clock error detection is now enabled if the "clock-error-detect"
property is set in the device tree.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Rename the RNG driver as it is usable by other STM32 platforms
than the STM32MP1x ones. Rename CONFIG_RNG_STM32MP1 to
CONFIG_RNG_STM32
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The Andes PLMT driver directly accesses the mtime MMIO region,
indicating its intended use in the M-mode boot stage. However,
since U-Boot proper (S-mode) also uses the PLMT driver, we need
to specifically mark the region as readable through PMPCFGx (or
S/U-mode read-only shared data region for Smepmp) in OpenSBI.
Granting permission for this case doesn't make sense. Instead,
we should use the generic RISC-V timer driver to read the mtime
through the TIME CSR. Therefore, we add the SPL_ANDES_PLMT_TIMER
config, which ensures that the PLMT driver is linked exclusively
against M-mode U-Boot or U-Boot SPL binaries.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Add timer driver in Starfive SoC. It is an timer that outside
of CPU core and inside Starfive SoC.
Signed-off-by: Kuan Lim Lee <kuanlim.lee@starfivetech.com>
Reviewed-by: Wei Liang Lim <weiliang.lim@starfivetech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
timer_get_boot_us function is required to record the boot stages as
us-based timestamp.
To get a micro-second time from a timer tick, this converts the
formula like below to avoid zero result of (tick / rate) part.
From: time(us) = (tick / rate) * 1000000
To : time(us) = (tick * 1000) / (rate / 1000)
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
timer_get_boot_us function is required to record the boot stages as
us-based timestamp.
To get a micro-second time from a timer tick, this converts the
formula like below to avoid zero result of (tick / rate) part.
From: time(us) = (tick / rate) * 1000000
To : time(us) = (tick * 1000) / (rate / 1000)
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Synchronize R8A774E1 RZ/G2H clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774C0 RZ/G2E clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774B1 RZ/G2N clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774A1 RZ/G2M clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779G0 V4H clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
The PLL2_VAR is not implemented yet and PLL2 is still configured
as regular PLL2 only.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7791 M2-W and R8A7793 M2-N clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ PFC tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
