Definitions are according to the MV78460 Hardware Specifications.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
A385 BootROM fills into bits [31:28] of register 0x182d0 tracing value,
which represents in which state BootROM currently is. BootROM fills one
of the possible values: 0x2 (CPU initialization), 0x3 (UART detection),
0x6 (UART booting), 0x8 (PCI Express booting), 0x9 (parallel or SPI NOR
booting), 0xA (parallel or SPI NAND booting), 0xB (SATA booting) and 0xE
(SD / eMMC booting).
Meaning of these values matches TRACE_* macros from Marvell soc_spec.h file:
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/blob/u-boot-2013.01-armada-18.06/tools/marvell/doimage_mv/soc_spec.h
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This allows to merge BOOT_FROM_MMC and BOOT_FROM_MMC_ALT constants to one
macro. And also allows to extend other BOOT_FROM_* macros for other
variants.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
A385 BootROM treats strapping configuration 0x22 as SPI-NAND. So remove
incorrect definition 0x22 as SATA. SATA on A385 has configuration 0x2A.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
A385 BootROM treats strapping configuration 0x3f as invalid. When booting
fails (e.g. because of invalid configuration) then BootROM fallbacks to
UART booting.
Detecting BootROM fallback to UART booting is implemented in U-Boot since
commit 2fd4284051 ("ARM: mach-mvebu: handle fall-back to UART boot").
So there is no need to define BOOT_FROM_UART_ALT constant and special
handling for it anymore, remove it.
This change effectively revers commit f3a88e2ca1 ("arm: mvebu: fix boot
from UART on ClearFog Base").
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
In SPL are active memory maps set by the BootROM. Define them in cpu.h file
to the correct values. Some peripherals are not mapped at all.
Signed-off-by: Pali Rohár <pali@kernel.org>
Proper U-Boot moves SPI0 CS0 Flash mapping from 0xD4000000 to 0xF4000000
and change its size from 64 MB to 8 MB. Definitions are already in
MBUS_SPI_BASE/MBUS_SPI_SIZE macros. So define these macros also for SPL
build, use them in env_sf_get_env_addr() function and move this function
from spl.c to cpu.c to be available in Proper U-Boot too.
Signed-off-by: Pali Rohár <pali@kernel.org>
A number of CONFIG symbols have crept in that are never referenced in
code, so drop them here. Further, we have two symbols being enabled
in headers while already enabled correctly in Kconfig, so these lines
can also be removed.
Signed-off-by: Tom Rini <trini@konsulko.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for the Allecat5/Alleycat5X SoC. These are L3 switches with
an integrated CPU (referred to as the CnM block in Marvell's
documentation). These have dual ARMv8.2 CPUs (Cortex-A55). This support
has been ported from Marvell's SDK which is based on a much older
version of U-Boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
This patch implements LD eFuse programming support. Armada 385 contains two
LD eFuse lines, each is 256 bit long with one additional lock bit. LD 0
line is mapped to U-Boot fuse bank 64 and LD 1 line to fuse bank 65. U-Boot
32-bit fuse words 0-8 are mapped to LD eFuse line bits 0-255. U-Boot fuse
word 9 is mapped to LD eFuse line lock bit.
So to program LD 1 General Purpose Data line, use U-Boot fuse command:
=> fuse prog -y 65 0 0x76543210
=> fuse prog -y 65 1 0xfedcba98
=> fuse prog -y 65 2 0x76543210
=> fuse prog -y 65 3 0xfedcba98
=> fuse prog -y 65 4 0x76543210
=> fuse prog -y 65 5 0xfedcba98
=> fuse prog -y 65 6 0x76543210
=> fuse prog -y 65 7 0xfedcba98
=> fuse prog -y 65 8 0x1
Signed-off-by: Pali Rohár <pali@kernel.org>
Now that the new timer support is available for these platforms, let's
select this IF for all these platforms. This way it's not necessary
that each board changes it's config header.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
This converts CONFIG_SYS_L2_PL310 to Kconfig.
For omap2 and mvebu the 'select SYS_L2_PL310' locations were
determined using ./tools/moveconfig -i CONFIG_SYS_L2_PL310.
For mx6 I manually chose ARCH_MX6 as 'select' location. The
correctness has been verified using
$ ./tools/moveconfig.py -f ARCH_MX6 ~SYS_L2_PL310 ~SYS_L2CACHE_OFF
0 matches
That means whenever an ARCH_MX6 board had SYS_L2_PL310 disabled, this
was correctly reflected in SYS_L2CACHE_OFF. Thus it's safe to insert
the 'select' statement under ARCH_MX6.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
mbus driver is initialized from arch_cpu_init() callback which is called
before relocation. This driver stores lot of functions and structure
pointers into global variables, so it is data position dependent.
Therefore after relocations all pointers are invalid and driver does not
work anymore as all pointers referes to the old memory, which overlaps with
CONFIG_SYS_LOAD_ADDR and ${loadaddr}.
For example U-Boot fuse command crashes if loadaddr memory is cleared or
rewritten by some image loaded by U-Boot load command.
mw.w ${loadaddr} 0x0 10000
fuse read 0 1 2
Fix this issue by removing of all mbus global variables in which are stored
pointers to structures or functions which changes during relocation. And
replace it by direct function calls (not via pointers). With this change
fuse command finally works.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
Change detection of platform/cpu from runtime to compile time via config
define. This completely eliminates compiling code which is not going to run
on selected platform. Code which parses and prints device / revision id
still reads device id from MVEBU_REG_PCIE_DEVID register, but only once.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Armada 385 contains 64 lines of HD eFuse and 2 lines of LD eFuse. HD eFuse
is used for secure boot and each line is 64 bits long + 1 lock bit. LD
eFuse lines are 256 bits long + 1 lock bit. LD 0 line is reserved for
Marvell Internal Use and LD 1 line is for General Purpose Data. U-Boot
already contains HD eFuse reading and programming support.
This patch implements LD eFuse reading support. LD 0 line is mapped to
U-Boot fuse bank 64 and LD 1 line to fuse bank 65.
LD 0 Marvell Internal Use line seems that was burned in factory with some
data and can be read by U-Boot fuse command:
=> fuse read 64 0 9
LD 1 General Purpose Data line is by default empty and can be read by
U-Boot fuse command:
=> fuse read 65 0 9
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Allow to specify input parameters, define all available mbox commands
supported by CZ.NIC's secure firmware and also Marvell's fuse.bin firmware
and fix parsing response from Marvell OTP commands.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Generic A3720 mbox code is currently in Turris Mox specific board file
board/CZ.NIC/turris_mox/mox_sp.c. Move it to board independent arch file
arch/arm/mach-mvebu/armada3700/mbox.c.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This register is referenced in one location and does not seem
configurable, so remove it from CONFIG namespace.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Do not call pci_set_region() for resources which were not properly mapped.
This prevents U-Boot to access unmapped memory space.
Update MBUS_PCI_MEM_SIZE and MBUS_PCI_IO_SIZE macros to cover all PCIe MEM
and IO ranges. Previously these macros covered only address ranges for the
first PCIe port. Between MBUS_PCI_IO_BASE and MBUS_PCI_MEM_BASE there is
space for six 128 MB long address ranges. So set MBUS_PCI_MEM_SIZE to value
of 6*128 MB. Similarly set MBUS_PCI_IO_SIZE to 6*64 KB.
Function resource_size() returns zero when start address is 0 and end
address is -1. So set invalid resources to these values to indicate that
resource has no mapping.
Split global PCIe MEM and IO resources (defined by MBUS_PCI_*_* macros)
into PCIe ports in mvebu_pcie_bind() function which allocates per-port
based struct mvebu_pcie, instead of using global state variables
mvebu_pcie_membase and mvebu_pcie_iobase. This makes pci_mvebu.c driver
independent of global static variables (which store the state of
allocation) and allows to bind and unbind the driver more times.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Move the function get_boot_device() from spl.c to cpu.c.
Make it visible, so that it may be used from other files.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
File mach/soc.h is included also in 64-bit mvebu processors, so define
Armada XP related macros only when compiling for Armada XP.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
This mvebu axp platform always uses fixed 250 MHz TCLK. So specify this
CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of
manual configuration in every board file.
Now every #if-#else case of soc.h file defines CONFIG_SYS_TCLK, so remove
useless default CONFIG_SYS_TCLK value from the end of soc.h file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This mvebu msys platform always uses fixed 200 MHz TCLK. So specify this
CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of
manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Bit 20 in SAR register specifies if TCLK is running at 200 MHz or 166 MHz.
Use this information instead of manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Bit 15 in SAR register specifies if TCLK is running at 200 MHz or 250 MHz.
Use this information instead of manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This function does not return, so add the appropriate compiler flag.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Some of the setups including cn9130 opens mmio window starting from
0xc0000000, reflect it in the u-boot code.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
There is region left by ATF, which needs to remain in memory to provide RT
services. To prevent overwriting it by u-boot, do not provide any mapping
for this memory region, so any attempt to access it will trigger
synchronous exception.
Update sr 2021-04-12:
Don't update armada3700/cpu.c mmu table, as this has specific changes
included in mainline.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Config option ARMADA_39X is never set so remove all dead code hidden under
ifdef CONFIG_ARMADA_39X blocks.
Also remove useless checks for CONFIG_ARMADA_38X define as this macro is
always defined for a38x code path.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
In case when ARM Trusted Firmware changes the default address of PCIe
regions (which can be done for devices with 4 GB RAM to maximize the
amount of RAM the device can use) we add code that looks at how ATF
changed the PCIe windows in the CPU Address Decoder and changes given
device-tree blob accordingly.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently on Armada-37xx the mem_map structure is statically defined to
map first 2 GB of memory as RAM region, and system registers and PCIe
region device region.
This is insufficient for when there is more RAM or when for example the
PCIe windows is mapped to another address by the CPU Address Decoder.
In the case when the board has 4 GB RAM, on some boards the ARM Trusted
Firmware can move the PCIe window to another address, in order to
maximize possible usable RAM.
Also the dram_init and dram_init_banksize looks for information in
device-tree, and therefore different device trees are needed for boards
with different RAM sizes.
Therefore we add code that looks at how the ARM Trusted Firmware has
configured the CPU Address Decoder windows, and then we update the
mem_map structure and compute gd->ram_size and gd->bd->bi_dram bank
base addresses and sizes accordingly.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Move Armada-8k specific DRAM init code into armada-8k specific
directory.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
