This patch is used to support DBD owner fuse changed to S400 only.
The XRDC PDAC2 for LPAV pbridge5 and MSC1/2/3 for GPIO and LPAV are not
configured by S400 default setting. So these PDAC and MSC are invalid,
only DBD owner can access the corresponding resources.
We have to configure necessary PDAC and MSC for SPL before DDR
initialization.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
To fit the DBD_EN fused part, we re-design the TRDC and XRDC assignment.
M33 will be the TRDC owner and needs to configure TRDC. A35 is the
XRDC owner, ATF will configure XRDC.
The handshake between U-boot and M33 image is used to sync TRDC and
XRDC configuration completion. Once the handshake is done, A35 and M33
can access the allowed resources in others domain.
The handshake is needed when M33 is booted or DBD_EN fused, because both
cases will enable the TRDC. If handshake is timeout, the boot will hang.
We use SIM GPR0 to pass the info from SPL to u-boot, because before the
handshake, u-boot can't access SEC SIM and FSB.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
In both SPL and u-boot, after probing the S400 MU, get the chip revision,
lifecycle and UID from Sentinel.
Update get_cpu_rev to use the chip revision not hard coded it for A0
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Move to using .env file for setting up environment variables for am65x.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Include ti_armv7_common.env and ti/mmc.env, which includes' K3 common
environment variables used across different K3 boards.
This patch depends on
https://lore.kernel.org/all/20230315052745.110502-1-n-francis@ti.com/
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move to using .env file for setting up environment variables for J721E
and J7200.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move to using .env file for setting up environment variables for J721S2.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For non TI boards it is not possible to enable the do_board_detect()
call as TI_I2C_BOARD_DETECT is defined in board/ti/common/Kconfig.
I want to use do_board_detect() to dectect boards and properties based
on some SPI communication with a FPGA.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Kconfig does not support using 'select' to select a 'choice'. A choice
can be configured by either setting the choice symbol to 'y' in a
configuration file or by setting a 'default' of the choice.
In board/ti/*/Kconfig the SOC_K3_* choice is already set to 'y' in their
corresponding configs/*_defconfig file. So remove selecting it.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
The M.2 slots of the related IOT2050 variant need to be configured
according to the plugged cards. This tries to detect the card using the
M.2 configuration pins of the B-key slot. If that fails, a U-Boot
environment variable can be set to configure manually. This variable is
write-permitted also in secure boot mode as it is not able to undermine
the integrity of the booted system.
The configuration is then applied to mux the serdes and to fix up the
device tree passed to or loaded by the bootloader. The fix-ups are
coming from device tree overlays that are embedded into the firmware
image and there also integrity protected. The OS remains free to load
a device tree to which they do not apply: U-Boot will not fail to boot
in that case.
Based on original patch by Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
User-button is controlled by the mcu domain gpio number 25.
But main0 main1 mcu domain all have gpio number 25.
To identify where the gpio is from, Using gpio controll base as the prefix
to indicate the gpio resource.
Signed-off-by: chao zeng <chao.zeng@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use external blob otpcmd.bin to replace the 0xff filled OTP programming
command block to create a firmware image that provisions the OTP on
first boot. This otpcmd.bin is generated from the customer keys using
steps described in the meta-iot2050 integration layer for the device.
Based on original patch by Baocheng Su.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Allows run-time control over watchdog auto-start and the timeout via
setting the environment variable watchdog_timeout_ms. A value of zero
means "do not start". Use CONFIG_WATCHDOG_TIMEOUT_MSECS as initial value
and this to zero by default. Users can then enable the watchdog once the
use and OS which picks it up during boot.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Anything that is not boot-env related is better kept there by now.
At this chance, also drop a stale comment from iot2050.h
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Refactor according to the entry `fit: Entry containing a FIT` of
document tools/binman/README.entries.
As the generator uses the device tree name for the config description,
board_fit_config_name_match requires a small adjustment as well.
Signed-off-by: Su Baocheng <baocheng.su@siemens.com>
[Jan: re-add now required CONFIG_OF_LIST, update config matching]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Due to different signature keys, the PG1 and the PG2 boards can no
longer use the same FSBL (tiboot3). This makes it impossible anyway to
maintaine a single flash.bin for both variants, so we can also split the
build.
A new target is added to indicates the build is for PG1 vs. PG2 boards.
Hence now the variants have separated defconfig files.
The runtime board_is_sr1() check does make no sense anymore, so remove
it and replace with build time check.
Documentation is updated accordingly. New binary artifacts are already
available via meta-iot2050.
Signed-off-by: Su Baocheng <baocheng.su@siemens.com>
[Jan: refactor config option into targets, tweak some wordings]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
- Fixes for booting newer revs of the SoC in the Raspberry Pi 4
- Propagate some firmware DT properties to the loaded DT
- Update the Zero2W upstream DT name
Here we implement usb_gadget_handle_interrupts() but did not include
<linux/usb/gadget.h> so did not have the declaration correct. Fix this
and add the missing include.
Signed-off-by: Tom Rini <trini@konsulko.com>
We did not add a prototype for spl_mmc_get_uboot_raw_sector to
include/spl.h before, so add and document one now. Correct the incorrect
prototype in board/advantech/imx8mp_rsb3720a1/imx8mp_rsb3720a1.c and
ensure that we have spl.h where we define a non-weak
spl_mmc_get_uboot_raw_sector as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Some platforms were not including <cpu_func.h> which sets the prototype
for reset_cpu, and in turn had it set wrong. Correct these cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable RWDT reset on Reset Controller so that it can be used as
reset trigger source for V3U Falcon.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Use one current_el() in board_init
U-Boot executes at EL3 is required to initalize those settings.
In other cases, they will be done by prior-stage firmware instead.
This fixes crash when U-Boot is at non-secure exception level.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The R-Car DTs might contains multiple /memory@* nodes from various
sources, i.e. prior firmware, u-boot itself or the OS
The duplicates are likely to happen so the messages are not meaningful
in the default setting since we have already handled that.
Reduce the message to debug level.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This board is using floating point arithmetic to display
the SST39VF6401B flash size.
This actually generates errors with toolchains without
appropriate sw fp math functions available.
SST39VF6401B is the only flash for wich the size is displayed,
it's size is 8192KB and floating point calculation seems not
needed. Removing it.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
Fix totally blank console at boot, clock value must be decimal,
as for the 30Mhz external crystal.
Fixes: 26e5944ec9 ("stmark2: Migrate CONFIG_SYS_EXTRA_OPTIONS to Kconfig")
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some Raspberry Pi 400 boards, specifically rev 1.1, have a different
address for the ethernet PHY device than what is provided by the kernel
DTB. The correct address is provided by the firmware, so we should carry
it over into the loaded device tree so that ethernet works on such boards.
Signed-off-by: Antoine Mazeas <antoine@karthanis.net>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
The RPI firmware adjusts several property values in the dtb it passes
to u-boot depending on the board/SoC revision. Inherit some of these
when u-boot loads a dtb itself. Specificaly copy:
* /model: The firmware provides a more specific string
* /memreserve: The firmware defines a reserved range, better keep it
* emmc2bus and pcie0 dma-ranges: The C0T revision of the bcm2711 Soc (as
present on rpi 400 and some rpi 4B boards) has different values for
these then the B0T revision. So these need to be adjusted to boot on
these boards
* blconfig: The firmware defines the memory area where the blconfig
stored. Copy those over so it can be enabled.
* /chosen/kaslr-seed: The firmware generates a kaslr seed, take advantage
of that.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Signed-off-by: Antoine Mazeas <antoine@karthanis.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Now that DM_ETH is enabled by default, there is no point in keeping the
non-DM_ETH code which initialized the ethernet interfaces.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Now that DM_ETH is enabled by default, there is no point in keeping the
non-DM_ETH code which initialized the ethernet interfaces.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Now that DM_ETH is enabled by default, there is no point in keeping the
non-DM_ETH code which initialized the ethernet interfaces.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Now that DM_ETH is enabled by default, there is no point in keeping the
non-DM_ETH code which initialized the ethernet interfaces.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The LX2160ARDB board has support for DM_ETH probed devices, which means
that we do not need to manually create an MDIO controller, register it,
create PHYs on it etc.
In order to cleanup the board file a bit, just remove this code entirely.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Odroid Go Ultra has 2 chained PMICs RK818 and RK818, and needs
an adjustment on the BUCK and LDO values.
Add the initial regulators values in -u-boot.dtsi & run the initial
regulator setup in a new odroid-go-ultra board.
Proper OTG and BOOST regulators are still missing to have USB-A
host properly working.
Link: https://lore.kernel.org/r/20230210-u-boot-odroid-go-ultra-pmics-setup-v1-1-1f16d62b76af@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
There are missing Kconfig dependencies in the code which is using
firmware interface.
The commit 71efd45a5f ("arm64: zynqmp: Change firmware dependency")
add option to also disable ZYNQMP_FIRMWARE. But not all Kconfig
dependencies were properly described and also sdhci and gem drivers
didn't protect the code properly.
So, add the missing ZYNQMP_FIRMWARE dependencies.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230201095553.11219-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The conditions in this code do not align when doing an SPL build with
split config. Use __maybe_unused to avoid needing to be so explicit.
Of course a better solution would be to refactor all of this to avoid
using #ifdef.
Signed-off-by: Simon Glass <sjg@chromium.org>
This causes a build failure on mx6cuboxi with split config, since CMD_SATA
shows up as enabled in SPl (because there is no SPL_CMD_SATA).
The condition is wrong anyway, so change it to use SATA instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_PG_WCOM_UBOOT_UPDATE_SUPPORTED defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
RK3588 has two memory gaps when using 16 GiB DRAM size:
[0x3fc000000 , 0x3fc500000]
and
[0x3fff00000 , 0x3ffffffff]
If the kernel is agnostic to these gaps, accessing the area causes
a SError panic.
Hence, add reserved memory areas in kernel's DTB before booting.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ROCK 5B is a Rockchip RK3588 based SBC (Single Board Computer) by Radxa.
There are tree variants depending on the DRAM size : 4G, 8G and 16G.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
MIPI CSI 2 multiple lanes connector
eMMC module connector
uSD slot (up to 128GB)
2x USB 2.0, 2x USB 3.0
2x HDMI output, 1x HDMI input
Ethernet port
40-pin IO header including UART, SPI, I2C and 5V DC power in
USB PD over USB Type-C
Size: 85mm x 54mm
Kernel commits:
a1d3281450ab ("arm64: dts: rockchip: Add rock-5b board")
6fb13f888f2a ("arm64: dts: rockchip: Update sdhci alias for rock-5b")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RK3588 from Edgeble AI.
General features:
- Rockchip RK3588
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
On module WiFi6/BT5 is available in the following Neu6 variants.
Neural Compute Module 6(Neu6) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
IO board offers plenty of peripherals and connectivity options and
this patch enables basic eMMC and UART which is enough to successfully
boot Linux.
Neu6 needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6(Neu6) IO platform.
Boot log for the record,
DDR Version V1.08 20220617
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
Manufacturer ID:0x6
CH0 RX Vref:31.7%, TX Vref:21.8%,21.8%
CH1 RX Vref:30.7%, TX Vref:22.8%,23.8%
CH2 RX Vref:30.7%, TX Vref:22.8%,22.8%
CH3 RX Vref:30.7%, TX Vref:21.8%,21.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL 2023.01-00952-g1d1785a516-dirty (Jan 30 2023 - 19:53:55 +0530)
Trying to boot from MMC1
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-391-g856309329:derrick.huang
NOTICE: BL31: Built : 14:15:50, Jul 18 2022
INFO: ext 32k is not valid
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: system boots from cpu-hwid-0
INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR: Error initializing runtime service opteed_fast
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9
U-Boot 2023.01-00952-g1d1785a516-dirty (Jan 30 2023 - 19:53:55 +0530)
Model: Edgeble Neu6A IO Board
DRAM: 7.5 GiB (effective 3.7 GiB)
Core: 71 devices, 15 uclasses, devicetree: separate
MMC: mmc@fe2c0000: 0
Loading Environment from nowhere... OK
In: serial@feb50000
Out: serial@feb50000
Err: serial@feb50000
Model: Edgeble Neu6A IO Board
Net: No ethernet found.
Hit any key to stop autoboot: 0
=>
Add support for Edgeble Neu6 Model A IO Board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update the MAINTAINERS file to include the devicetree for the
rk3568-evb1-v10 board.
Also update Rockchip board docs to include information on building
RK3568 based devices.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Radxa Compute Module 3(CM3) IO board an application board from Radxa
and is compatible with Raspberry Pi CM4 IO form factor.
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Add support for Radxa CM3 IO Board defconfig and -u-boot.dtsi
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The board should be RV1126-NEU2 instead RV1126-ECM0.
Fix the wrong name.
Fixes: b8f1ca9540 ("board: rockchip: Add Edgeble Neu2 IO Board")
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Radxa ROCK 3 Model A support. sync rk3308-rock-pi-s.dts from
Linux 6.2.0-rc7.
ROCK Pi S is RK3308 based SBC from radxa.com. ROCK Pi S has a,
- 256MB/512MB DDR3 RAM
- SD, NAND flash (optional on board 1/2/4/8Gb)
- 100MB ethernet, PoE (optional)
- Onboard 802.11 b/g/n wifi + Bluetooth 4.0 Module
- USB2.0 Type-A HOST x1
- USB3.0 Type-C OTG x1
- 26-pin expansion header
- USB Type-C DC 5V Power Supply
Linux commit commit for the same,
<2e04c25b1320> ("arm64: dts: rockchip: add ROCK Pi S DTS support")
Signed-off-by: Akash Gajjar <gajjar04akash@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Radxa ROCK 3 Model A support. sync rk3568-rock-3a.dts from Linux 6.2.0-rc7
Board Specifications
- Rockchip RK3568
- 2/4/8GB LPDDR4 3200MT/s
- eMMC socket, SD card slot
- GbE LAN
- PCIe 3.0/2.0
- M.2 Connector
- 3.5mm Audio jack with mic
- HDMI 2.0, MIPI DSI/CSI
- USB 3.0 Host/OTG, USB 2.0 Host
- 40-pin GPIO expansion ports
- USB Type C PD 2.0, 9V/2A, 12V/2A, 15V/2A, 20V/2A
Refer Linux commit <22a442e6586c>
("arm64: dts: rockchip: add basic dts for the radxa rock3 model a")
Signed-off-by: Akash Gajjar <gajjar04akash@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Configure PMIC voltages for early stages using updated
early i2c write.
Tested-by: Thierry Reding <treding@nvidia.com> # Beaver T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom <twarren@nvidia.com>
Move the environment to an easily editable text file in the boot
partition
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The current ae350-related defconfigs could also
support newer Andes CPU IP, so modify the names of CPU
from ax25 to andesv5, and board name from ax25-ae350 to ae350.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The L2-cache is not enabled currently, the enbale_caches() will call
the v5l2_enable() callback to enable it in SPL.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Synology DS116 is a NAS based on Marvell Armada 385 SoC.
Board Specification:
- Marvel MV88F6820 Dual Core at 1.8GHz
- 1 GiB DDR3 RAM
- 8MB Macronix mx25l6405d SPI flash
- I2C
- 2x USB 3.0
- 1x GBE LAN port (PHY: Marvell 88E1510)
- 1x SATA (6 Gbps)
- 3x LED
- PIC16F1829 (connected to uart1)
- GPIO fan
- serial console
Note that this patch depends on the add-support for Thecus N2350 patch:
https://patchwork.ozlabs.org/project/uboot/patch/20230201231306.7010-1-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Currently, only the 1st SATA port is powered up (by GPIO1 12).
Add GPIO1 13 in board initialization to power up the 2nd SATA port.
Note that this patch depends on the initial add-support patch:
https://patchwork.ozlabs.org/project/uboot/patch/20230201231306.7010-1-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- A fix for a long standing bug that has been exposed by commit
50128aeb0f ("cyclic: get rid of cyclic_init()") preventing 8xx boards
from booting since u-boot 2023.01
- A GPIO driver for powerpc 8xx chip
- Fixup for powerpc 8xx SPI driver
- A new powerpc 8xx board
- The two devices having that board.
This adds support for the MIAE and VGoIP devices.
Those devices have the same CPU board that the MCR3000_2G board.
The devices are very modular, they are provided with
interchangeable front and back panels.
Linux kernel is shipped with a device tree which contains all
possible setups, and U-boot eliminates unrelated nodes based on
detected hardware.
This patch was originally written by Charles Frey who's
email address is not valid anymore as he left the company.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
This adds a new board from CS GROUP. The board is called
MCR3000_2G, and has a CPU board called CMPC885.
That CPU board is shared with another equipment that will
be added in a later patch.
That board stores Ethernet MAC addresses in an EEPROM which
is accessed using SPI bus.
This patch was originally written by Charles Frey who's
email address is not valid anymore as he left the company.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
e1-wan device-tree node doesn't exist. Remove related update
to avoid following warning at startup:
Loading Device Tree to 007fa000, end 007ff951 ... OK
Unable to update property /localbus/e1-wan:data-rate, err=FDT_ERR_NOTFOUND
Unable to update property /localbus/e1-wan:channel-phase, err=FDT_ERR_NOTFOUND
Unable to update property /localbus/e1-wan:rising-edge-sync-pulse, err=FDT_ERR_NOTFOUND
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
Both U-boot and Linux kernel have grown over the last releases
and don't fit anymore in the 2M EPROM of the board.
So, rework the setup to allow storing the Linux kernel image
on the UBIFS NAND Flash.
Also add support to FIT images as this is what the Linux kernel
look like nowadays.
Also increase CFG_SYS_BOOTMAPSZ to 32Mbytes and define
CONFIG_SYS_BOOTM_LEN with the same value, otherwise it defaults
to 8M which is not sufficient anymore with nowadays Linux kernels.
And set the netmask to 255.255.255.0 as a class C address is used.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
We can move all of the environment changes to come
from CONFIG_EXTRA_ENV_TEXT.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
This converts 4 usages of this option to the non-SPL form, since there is
no SPL_FEC_MXC defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_FASTBOOT defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_WATCHDOG_AUTOSTART defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_TEN64_CONTROLLER defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_TARGET_PG_WCOM_SELI8 defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_TARGET_PG_WCOM_EXPU1 defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_TARGET_LX2160ARDB defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_SYS_MEM_RSVD_FOR_MMU defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_SL28_SPL_LOADS_OPTEE_BL32 defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_SL28CPLD defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_SIFIVE_OTP defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_RESV_RAM defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_PG_WCOM_UBOOT_UPDATE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_PG_WCOM_UBOOT_BOOTPACKAGE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_MICROBLAZE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_FSL_MC_ENET defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_FSL_CAAM defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_FDT_SIMPLEFB defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 4 usages of this option to the non-SPL form, since there is
no SPL_ENV_VARS_UBOOT_RUNTIME_CONFIG defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_ENV_IS_IN_UBI defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 13 usages of this option to the non-SPL form, since there is
no SPL_EFI_HAVE_CAPSULE_SUPPORT defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_DWC_ETH_QOS defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_DTB_RESELECT defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_CMD_STM32PROG defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_CMD_STBOARD defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_CMD_FRU defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_BNXT_ETH defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_ARCH_ZYNQ defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
as Tom suggested get rid of CFG_EXTRA_ENV_SETTINGS and
enable CONFIG_ENV_SOURCE_FILE and use text file
board/socrates/socrates.env
which contains the default environment. While at it,
cleanup the default Environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
Suggested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This option as well as CONFIG_TARGET_P1022DS and CONFIG_TARGET_P5020DS
are not defined anywhere. Drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not used since CONFIG_SYS_FPGA_COMMON is not defined anywhere.
Drop the code and the Makefile rule.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not used since this commit:
ed7fe2bee1 ppc: Remove xpedite boards
Drop the driver and Kconfig option.
Signed-off-by: Simon Glass <sjg@chromium.org>
convert socrates board to use MPC85XX_HAVE_RESET_VECTOR and
disable CONFIG_OF_BOARD and use common u-boot.dtsi for
creating u-boot-dtb.bin.
Signed-off-by: Heiko Schocher <hs@denx.de>
There are no differences for the different 832x targets we have in
the header defined with SYS_CONFIG_NAME. So we can join the five
headers to a single file.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Next step to get rid of the header files in icnlude/configs. Move
most of the defines to km83xx.c directly. Some remaining defines
which should go to Kconfig are moved to km-mpc83xx.h for now.
Also remove some unused defines and move one define to powerpc.env
as we only need it there.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Set splash screen related env variables. Default splash source is
set to mmc where user is expected to keep bmp in compressed format
with name ti.gz on first partition of mmc.
Splash file will be uncompressed to DDR at address 0x82000000 and
splash position is set to middle of screen.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Use .env file for setting board related environment variables,
in place of am62x_evm.h file. Except for BOOTENV settings, as
config_distro_boot.env file doesn't exist.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Splash screen function needs splash source information
to load image and display it, splash_location provides
the necessary info, Set default_splash_location to MMC
at partition 1:1. Probe DSS for splash screen display.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Convert to DM_SERIAL and drop the iomux board file
level init as it's handled as part of the DM serial
layer instead.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This moves over the PMIC power init to DM and the associated i2c and
regulator bits.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add MV88E61XX DSA support:
- update dt to provide internal MDIO bus and port handles.
U-Boot requires a more restrictive subset of the dt bindings
required by Linux for the sake of simplifying code
- update defconfig to remove old driver and enable new one
- replace mv88e61xx_hw_reset weak override with board_phy_config support
for register configuration that is outside the scope of the DSA driver
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Original OpenSBI (without FW_PIC) will relocate itself
from 0x1000000 to 0x0. After OpenSBI added FW_PIC codes,
it will not relocate any more and always run at 0x1000000.
Hence, it may overlap with Kernel memory region. So it is
necessary to change OpenSBI address from 0x1000000 to 0x0.
More details can refer to commit cb052d7712
("riscv: qemu: spl: Fix booting Linux kernel with OpenSBI 1.0+")
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
As explained in the text at the bottom of the page
https://source.codeaurora.org/external/qoriq/qoriq-components/rcw:
"QUIC repositories on this site will not receive any updates after
March 31, 2022, and will be deleted on March 31, 2023."
Point to the NXP RCW github repo instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In some situations the GSC firmware where the EEPROM containing the
model and DRAM configuration may not be ready by the time the SoC
is ready to talk to it over I2C.
Instead of a hard delay, poll the I2C lines to wait until they are
released to avoid the I2C drivers 'Arbitation lost' error message.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
As explained in the text at the bottom of the page
https://source.codeaurora.org/external/imx/imx-atf:
"QUIC repositories on this site will not receive any updates after
March 31, 2022, and will be deleted on March 31, 2023."
Point to the NXP ATF github repo instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
All Apalis iMX8 variants have 2nd RGMII on SoC, so add the address
for 2nd ethernet.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Add the board detection mechanism to be able to support
the 2GB variant.
Based on the code from TechNexion U-Boot downstream tree.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add the board support for the i.MX8MM Cloos PHG board.
This board uses a imx8mm-tqma8mqml SoM from TQ-Group.
imx8mm-phg.dts and imx8mm-tqma8mqml.dtsi are taken
directly from Linux 6.2-rc3.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Pull common.c into common subdirectory of the board file,
since this code can be reused by other Data Modul SBCs.
Drop the include of lpddr4_timing.h, which is unneeded.
Signed-off-by: Marek Vasut <marex@denx.de>
The icache is enabled in common architecture code since commit:
2fa763baa1 ("ARM: imx: Enable instruction cache early on on i.MX8M")
Drop the board side duplicate code.
Signed-off-by: Marek Vasut <marex@denx.de>
The PCA9450 reset configuration can now be performed by the PCA9450 PMIC
driver itself, remove the hard-coded variant from board code and let the
PMIC driver perform this task using one-liner:
```
$ sed -i '/set WDOG_B_CFG to cold reset/,+2 d' $(git grep -l PCA9450_RESET_CTRL.*0xA1 board/)
```
Venice and i.MX93 EVK required slight manual fix up.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Remove a duplicate of weak board_phy_config() implementation
in drivers/net/phy/phy.c.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Display build info with information about the version of SCFW, SECO and
TF-A (ATF).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
U-Boot typically tears down the display controller before handing
control over to Linux. On LCD displays disabling pixel clock leads to a
fading out effect with vertical/horizontal lines. Make sure to disable
back light GPIO Apalis BKL1 before booting Linux.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>