The AM64x SR2.0 SK board uses "AM64B-SKEVM" as the EEPROM identifier.
This board is similar to the AM64x SKEVM except that it has a new
PMIC that will be enabled in the future and consequently could use a
different device tree file in the future.
For now we treat the board same as an AM64x SK.
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
To enable splash screen on AM62x at a53 SPL setup DRAM, set page table,
enable cache to allow copying of bmp image to frame buffer and display
it using splash_display.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Change splashimage which is bmp image loadaddr to 0x80200000 since stack
is situated at 0x80477660 as splash framework requires bmp image to be
present above stack.
Change splashsource to sf to support loading bmp image from ospi flash
memory.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
When CMPC885 board is used for MIAE device, SCC2 SCC3 and SMC2
are used for serial lines. Therefore only SCC4 is available for
handling the TDM line.
In order to use SCC4 in QMC mode without loosing SMC2, SMC2
must be relocated.
Activate SMC relocation and relocate SMC2 at offset 0x1fc0 which
is unused.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
In order to know the motherboard type earlier, perform I/O ports
initialisation and FPGA loading in board_early_init_f() instead
of board_early_init_r().
This is needed to be able to load mpc8xx CPM microcode base on
motherboard type and before starting to use the CPM.
Console is not available yet so remove the printfs.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
This platform is unsupported by TI and was never widely distributed. As
this is untested for a long while and missing some DM conversions,
remove it and related device tree files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support to detect daughtercards (GESI Ethernet card) in-order
to set the MAC address of the main CPSW2G interface.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Currently a few 'board/qualcomm/../Makefile' point to incorrect
path of sdm845 board file.
Fix the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
This adds a simple Northstar "BRCMNS" board to be used with
the BCM4708x and BCM5301x chips.
The main intention is to use this with the D-Link DIR-890L
and DIR-885L routers for loading the kernel into RAM from
NAND memory using the BCH-1 ECC and using the separately
submitted SEAMA load command, so we are currently not adding
support for things such as networking.
The DTS file is a multiplatform NorthStar board, designed to
be usable with several NorthStar designs by avoiding any
particulars not related to the operation of U-Boot.
If other board need other ECC for example, they need to
create a separate DTS file and augment the code, but I don't
know if any other users will turn up.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, it is recommended to move from CFG_EXTRA_ENV_SETTINGS to
an env file, so do the conversion.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently, only the first MAC address is read from the fuses.
The second MAC address is not read and Linux assigns a random one.
To prevent this behavior, read the second MAC address from the fuses
and store it into the eth1addr environment variable so that it
can be passed to Linux.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add lockdown U-Boot env support so that only certain U-Boot environment
variables are allowed to be modified.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
GPT Partition labels are used for determining the right
root filesystem to boot from.
The U-Boot environment is configured to reside in the eMMC hardware
boot partition we are currently booted from.
This should enable a dual copy approach for upgrading the bootloader.
One can overwrite the inactive hardware partition with new bootloader
and environment and afterwards switch the eMMC boot partition for an
atomic bootloader switch.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
The MNT Reform 2 is a modular DIY laptop. In its initial version it
is based on the BoundaryDevices i.MX8MQ SoM. Some parts have been
lifted from BoundaryDevices official U-Boot downstream project.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Please pull the second part of the sunxi pull request for this cycle.
Another bunch of patches that replace old-school U-Boot hacks with
proper DM based code, this time for the raw NAND flash driver, and the
USB PHY VBUS detection code. Plus two smaller patches that were sitting
in my inbox for a while.
Gitlab CI passed. In lack of some supported board with NAND flash I
couldn't really test this part, but apparently this was tested by the
reviewer. I briefly ran the branch on some boards with USB-OTG, and
this still worked.
This pull request adds support for the last CPU board from
CS GROUP France (previously CSSI).
That CPU board called CMPCPRO has a mpc8321E CPU (Family PQII PRO hence
its name) and can be plugged in place of the CMPC885 board.
In order to support that new board, the following changes are included
in this series:
- Make the mpc8xx watchdog driver more generic for reusing it
with mpc83xx
- Fix various small problems on mpc83xx platform
- Add a GPIO Driver for QE GPIOs
- Add support for mpc832x into mpc83xx SPI driver
- Refactor existing board code that will be shared with new board
- Add the new board
CSSI has another CPU board, similar to the CMPC885 board
that get plugged on the two base boards MCR3000_2G and MIAE.
That CPU board is called CMPCPRO because it has a MPC8321E CPU,
also known as Power QUICC II PRO.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
All the code used to manage the mother boards will be
common to soon to come CPU board.
Move all that code into common.c
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
On cmpc885 board, the ethernet addresses are stored in an
EEPROM that is accessed through SPI.
A 3 bytes command is sent to the chip then the content
gets read. At the time being a single block access is
performed, ignoring the first 3 bytes read.
Reword the SPI transfer to first send 3 bytes then
receive the content of the EEPROM so that there don't be
3 dummy bytes at the beginning of the buffer.
And move the function into common.c so that it can be
reused by the board that will be added in a future patch.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
In preparation of the new cssi board called cmpcpro which
we be introduce in a future patch, move common
functions into a dedicated file in a common directory.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Clocks, resets, and pinmuxes are now handled by the driver model, so the
only thing the "board" code needs to do is load the driver. This matches
the pattern used by other DM raw NAND drivers (there is no NAND uclass).
The actual board code is now only needed in SPL.
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When building with clang, we see:
board/emulation/common/qemu_dfu.c:51:24: warning: 'memset' call operates on objects of type 'char' while the size is based on a different type 'char *' [-Wsizeof-pointer-memaccess]
As we're calling memset with the length set to the size of the pointer
and not the size of the buffer. Correct this with a call of the size of
the buffer itself.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Sughosh Ganu <sughosh.ganu@linaro.org>
The Arm EBBR (Embedded Base Boot Requirements) require that the time
and basic networking EFI interfaces are available and working, so long
as the hardware has an RTC and network interface.
Arm FVPs typically have a memory-mapped PL031 RTC and a VIRTIO_NET
device defined in the device tree, so "imply" these in the Kconfig for
the FVP base model to simplify creating EBBR-compliant firmware.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
BASE_FVP now typically uses a devicetree provided by a prior boot stage
(typically Arm TF-A), so imply this option by default when
TARGET_VEXPRESS64_BASE_FVP is selected.
OF_HAS_PRIOR_STAGE selects OF_BOARD so this change is minor, but aligns
TARGET_VEXPRESS64_BASE_FVP with TARGET_VEXPRESS64_BASER_FVP.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Move to using .env file for setting up environment variables for am64x.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Add ospi boot media support to load splash image from OSPI memory,
add offset to read image from ospi and necessary flags defininig type
of storage and storage device.
Use CONFIG_IS_ENBALED to use the splash locations at SPL and u-boot
proper.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
This matches AM64 and J721e and removes the need to forward
declare k3_spl_init(), k3_mem_init(), and check_rom_loaded_sysfw()
in sys_proto.h.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This matches how it was done for pre-K3 TI platforms and it allows
us to move the forward declaration out of sys_proto.h.
It also removes the need for K3_BOARD_DETECT as one is free to simply
override the weak function in their board files as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The TARGET_x_R5_EVM check is already enough to limit these defines to
only the correct builds. Remove the extra outer check.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The MSMC fixup is something we do based on SoC, not based on the board.
So this fixup does not belong in the board files. Move this to the
mach-k3 common file so that it does not have to be done in each board
that uses these SoCs.
We use ft_system_setup() here instead of ft_board_setup() since it is no
longer board level. Enable OF_SYSTEM_SETUP in the configurations that use
this to keep functionality the same.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
- Add rk3588 evb support;
- Update pinctrl for rk3568 and rk3588;
- Update rk3288 dts;
- Update mmc support for rk3568 and rk3588;
- Add rng support for rk3588;
- Add DSI support for rk3568;
- Some other misc fixes in dts, config, driver;
_ Add usb_pgood_delay for ST boards
_ increase malloc size for pre-reloc for stm32mp15
_ Set CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2s for stm32mp15
dts:
_ Add QSPI support on STM32MP13x SoC family
_ Add FMC support on STM32MP13x SoC family
drivers/machine:
_ pinctrl_stm32: Add slew rate support for stm32_pinctrl_get_pin_muxing()
_ spi: stm32_qspi: Remove useless struct stm32_qspi_flash
_ rawnand: stm32_fmc2: remove unsupported EDO mode
_ stm32mp: fix various array bounds checks
-----BEGIN PGP SIGNATURE-----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=3Txq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20230419' of https://source.denx.de/u-boot/custodians/u-boot-stm
configs:
_ Add usb_pgood_delay for ST boards
_ increase malloc size for pre-reloc for stm32mp15
_ Set CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2s for stm32mp15
dts:
_ Add QSPI support on STM32MP13x SoC family
_ Add FMC support on STM32MP13x SoC family
drivers/machine:
_ pinctrl_stm32: Add slew rate support for stm32_pinctrl_get_pin_muxing()
_ spi: stm32_qspi: Remove useless struct stm32_qspi_flash
_ rawnand: stm32_fmc2: remove unsupported EDO mode
_ stm32mp: fix various array bounds checks
rk3588 evb1 v10 is a evalution board from Rockchip, it is a dev board for
rockchip and also a reference board for board vendors.
Hardware:
SoC: RK3588
DRAM: LPDDR4X 8GB
Debug: UART2 via USB
PCIe: 3x4 *1
SATA *2
HDMI out *2
HDMI IN *1
USB2.0 Host *2
USB3.0 Host *1
Type C *1
MIPI DSI panel
dts Sync from Linux v6.2.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@edgeble.ai>
Instead of letting the compiler error out if CONFIG_ENV_IS_NOWHERE is
not selected by the user, let's just enforce it when the user builds for
Ringneck PX30 so that no check needs to be performed by the compiler and
the configuration is always valid.
Suggested-by: Tom Rini <trini@konsulko.com>
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Instead of letting the compiler error out if CONFIG_ENV_IS_NOWHERE is
not selected by the user, let's just enforce it when the user builds for
Puma RK3399 so that no check needs to be performed by the compiler and
the configuration is always valid.
Suggested-by: Tom Rini <trini@konsulko.com>
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Kconfig to select the basic functions for StarFive VisionFive v2 Board.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Add board support for StarFive VisionFive v2.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
In all these cases, the index on the LHS is immediately afterwards
used to access the array appearing in the ARRAY_SIZE() on the RHS - so
if that index is equal to the array size, we'll access
one-past-the-end of the array.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
- Spring Cleanup of Amlogic board documentation
- add support for BananaPi M2-Pro
- add support for BananaPi M2S
- add support for Radxa Zero2
- add support for WeTek Hub and WeTek Play2
- switch LibreTech-CC v2 and WeTek Core2 to EE powerdomain
- add support for Beelink GT1 Ultimate
-----BEGIN PGP SIGNATURE-----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=Vf7Q
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20230417' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Add initial support for BPI-CM4
- Spring Cleanup of Amlogic board documentation
- add support for BananaPi M2-Pro
- add support for BananaPi M2S
- add support for Radxa Zero2
- add support for WeTek Hub and WeTek Play2
- switch LibreTech-CC v2 and WeTek Core2 to EE powerdomain
- add support for Beelink GT1 Ultimate
The first two patches are by Frieder Schrempf who joins as a reviewer for
the SPI NAND framework and drivers.
The following 2 patches are by Linus Walleij and are taken by the series
"Add Broadcom Northstar basic support".
Bin Meng makes static a list for octeontx.
Francesco Dolcini specifies MTD partitions on command line for
colibri-{imx6ull,imx7}.
-----BEGIN PGP SIGNATURE-----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=1lGu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-nand-20230417' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash
Pull request for u-boot-nand-20230417
The first two patches are by Frieder Schrempf who joins as a reviewer for
the SPI NAND framework and drivers.
The following 2 patches are by Linus Walleij and are taken by the series
"Add Broadcom Northstar basic support".
Bin Meng makes static a list for octeontx.
Francesco Dolcini specifies MTD partitions on command line for
colibri-{imx6ull,imx7}.
