Add print_cpuinfo() to print SoC info like family & revision.
This function depends on CONFIG_DISPLAY_CPUINFO config.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move tapdelay function calls to zynq_sdhci.c and make them static
inline. zynqmp_tap_delay.h has function prototypes for the functions
defined in tap_delays.c, which will not be needed anymore.
Remove tap_delays.c and zynqmp_tap_delay.h files.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Currently xilinx sdhci driver is using zynqmp_mmio_write() to set
tapdelay values and DLL resets. Continue to use this for SPL and mini
U-Boot where U-Boot will be executed at EL3 level.
Use firmware call xilinx_pm_request() using appropriate arguments to
set input/output tapdelays and also for DLL resets in regular flow(EL2).
Host driver should explicitly request DLL reset before ITAP (assert DLL)
and after OTAP (release DLL) to avoid issues in some cases. Also handle
error return where possible.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
fsl-qoriq: Fixes related to env, spi, usb, crypto, configs, distro-boot
for Layerscape Boards like lx2, sl28, ls2088ardb.
powerpc: Fixes for t208xrdb revd board and cortina related configs
update for T208xRDB, T4240RDB.
T4240RDB supports booting from 2 nor banks(default and altbank). The
corresponding defconfig can only have one entry defined and therefore,
extend cs4340_get_fw_addr() function to overwrite firmware address which
will be later used in cortina firmware.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
T2080RDB supports booting from 2 nor banks(default and altbank). The
corresponding defconfig can only have one entry defined and therefore,
extend cs4340_get_fw_addr() function to overwrite firmware address which
will be later used in cortina firmware.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
LS2088A-RDB supports TFA boot source and has 2 nor banks(default and
altbank) and QSPI as boot source. The corresponding defconfig can only
have one entry defined and therefore, extend cs4340_get_fw_addr()
function to overwrite firmware address which will be later used in
cortina firmware.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Free dynamically allocated memory before every return statement
in calc_img_key_hash() and calc_esbchdr_esbc_hash() function.
Verified the secure boot changes using ls1046afrwy board.
Signed-off-by: Kshitiz Varshney <kshitiz.varshney@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Starting with board revision D, the MISCCSR CPLD register needs to be
configured to enable Power-on Reset for software reset commands.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add board_fdt_blob_setup to return the device tree location which is
passed by prior stage in u-boot proper. The generic board_fdt_blob_setup
always returns _end, it mignt be ok because u-boot SPL would currently
put the dtb there, but it would be broken if we put the dtb to another
place and assigned the location into a1 register for u-boot proper. Use
the location passed by prior stage would make more sence, because we
actually pass the location to u-boot proper and want to use that one,
rather than the dtb which in _end.
We can't use CONFIG_OF_PRIOR_STAGE because it doens't distinguish the
implementation of u-boot SPL and u-boot proper, so u-boot SPL need to
reply on the prior stage to pass device tree location as well, but we
don't pass the DT from boot rom now. In addition, when
CONFIG_OF_PRIOR_STAGE is enabled, the u-boot-spl.bin and u-boot.itb won't
include the device tree.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
As (3581811dc2 "riscv: sifive/fu540: Move SPL related functions to spl.c"),
we put the SPL stuff in spl.c, we don't need to compile unleashed.c and
unmatched.c in SPL build.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The USB recovery mode is used by Toradex to load the Toradex Easy
Installer image which supports further system images installation.
Prepare for loading and launching the Toradex Easy Installer if the
USB Recovery mode is activated.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add TF-A FIP support for trusted boot on STM32MP15x,
when STM32MP15x_STM32IMAGE is not activated.
With FIP support the SSBL partition is named "fip" and its size is 4MB,
so the ENV partition name in device tree (for SD card or eMMC)
or offset in defconfig (CONFIG_ENV_OFFSET / CONFIG_ENV_OFFSET_REDUND)
need to be modified.
With FIP the TEE MTD partitions are removed because the OP-TEE binray are
included in the FIP containers.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
By default for trusted boot with TF-A, U-Boot (u-boot-nodtb)
is located in FIP container with its device tree and with
the secure monitor (provided by TF-A or OP-TEE).
The FIP file is loaded by TF-A BL2 and each components is
extracted at the final location.
This patch add CONFIG_STM32MP15x_STM32IMAGE to request the
STM32 image generation for SOC STM32MP15x
when FIP container is not used (u-boot.stm32 is loaded by TF-A
as done previously to keep the backward compatibility).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
- Convert GoFlex Home Ethernet and SATA to Driver Model (Tony)
- mvebu: Automatically detect CONFIG_SYS_TCLK (Pavel)
- mvebu: sata_mv: Fix HDD identication during cold start (Tony)
- a37xx: pci: Fix handling PIO config error responses (Pavel)
- Other minor misc changes and board maintainer updates
- sei610 & meson64_android cleanups to prepare android 11 boot support
- use Android BCB mechanism for reboot reason instead of HW reboot flag
- Switch meson64_android boot flow to use abootimg for A/B, AVB and DTBO support
-----BEGIN PGP SIGNATURE-----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=RZ8+
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20210810' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- odroid-n2: fix fdtfile suffix for n2-plus
- sei610 & meson64_android cleanups to prepare android 11 boot support
- use Android BCB mechanism for reboot reason instead of HW reboot flag
- Switch meson64_android boot flow to use abootimg for A/B, AVB and DTBO support
Enable support to the 2 NOR flashes on the QEMU RISC-V virt machine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Change maintainer to me. Suriyan no longer has this board and wishes
to see someone maintaining it actively.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Change maintainer to me. Eric no longer has this board and wishes
to see someone maintaining it actively.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
In DM Ethernet, the old "egiga0" name is no longer valid,
so replace these with Ethernet PHY names from device tree. Also, read
Ethernet PHY address from device tree.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The N2+ dtb is meson-g12b-odroid-n2-plus.dtb, not n2_plus, so
correct the suffix provided in the board file. Also align the
board ident string shown during boot to match.
Fixes: 8bc780106c ("board: amlogic: odroid: add runtime detection of the N2/N2+/C4/HC4 variants")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART
Log as below: I would keep some debug info for now, and after we move
to be stable and production launch, we could drop that.
U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
Normal Boot
upower_init: soc_id=48
upower_init: version:11.11.6
upower_init: start uPower RAM service
user_upwr_rdy_callb: soc=b
user_upwr_rdy_callb: RAM version:12.6
Turn on switches ok
Turn on memories ok
Clear DDR retention ok
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F0 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
complete
De-Skew PLL is locked and ready
WDT: Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x3a800 by ROM_API
NOTICE: BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94
NOTICE: BL31: Built : 01:56:58, Jun 29 2021
NOTICE: upower_init: start uPower RAM service
NOTICE: user_upwr_rdy_callb: soc=b
NOTICE: user_upwr_rdy_callb: RAM version:12.6
U-Boot 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
CPU: Freescale i.MX8ULP rev1.0 at 744 MHz
Reset cause: POR
Boot mode: Single boot
Model: FSL i.MX8ULP EVK
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... ***
Warning - bad CRC, using default environment
In: serial@293a0000
Out: serial@293a0000
Err: serial@293a0000
Net:
Warning: ethernet@29950000 (eth0) using random MAC address -
96:35:88:62:e0:44
eth0: ethernet@29950000
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the specific board model from EEPROM config to the device-tree to
make it easier to access from Linux userspace.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Make the conversion to driver model as it is mandatory.
Successfully tested booting Linux from the SD card.
Dropped support for networking and splash screen as these need
to be properly converted to DM and tested.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
Do the following to add support for it:
- add dts
- add PMIC config
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add board model/serial# strings to env. Move the creation of the strings
to gsc_read() and the display of the info into gsc_info() so they are
available to U-Boot proper.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
replace looking up i2c bus name by bus number and define bus numbers and
eeprom address with #defines.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The intention of commit d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT
with CONFIG_IMX_HAB") was to convert from CONFIG_SECURE_BOOT to
CONFIG_IMX_HAB, but it replaced with an extra "_" character.
Fix it by using the correct CONFIG_IMX_HAB symbol.
Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The GW54xx-G revision has the foolowing changes:
- replaces the EOL GbE PHY with an updated part (requires an enable pin)
- replaces the EOL analog video decoder with an updated part
(requires dt prop)
- add power control to miniPCIe socket
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW53xx-G revision has the foolowing changes:
- replaces the EOL GbE PHY with an updated part (requires an enable pin)
- replaces the EOL analog video decoder with an updated part
(requires dt prop)
- add power control to miniPCIe socket
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW5913 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
- DDR3 DRAM
- NAND FLASH (256MiB or 2048MiB)
- Gateworks System Periperhal Controller
- front panel LED's
- front panel pushbutton
- Digital I/O connector (I2C/GPIO/UART)
- u-blox Zoe-M8Q GPS
- 1x RJ45 GbE
- 1x MiniPCIe socket with PCIe USB 2.0 and nanoSIM socket
- Passive PoE and wide-range DC power supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW5912 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
- DDR3 DRAM
- NAND FLASH (256MiB or 2048MiB)
- microSD socket
- Gateworks System Periperhal Controller
- front panel LED's
- front panel pushbutton
- RS232 connector (2x UARTs)
- CAN/RS485 connector
- Digital I/O connector (I2C/GPIO)
- SPI connector
- u-blox Zoe-M8Q GPS
- LIS2DE12 Accellerometer
- 1x FEC GbE RJ45 with 802.3at Active PoE
- 1x PCI GbE RJ45 with Passive PoE
- 5x MiniPCIe socket with PCIe/USB 2.0
- 1x MiniPCIe socket with PCIe/USB 2.0 and SIM socket
- Aux power input with wide-range DC power supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW5910 is a Single Board Computer based on the NXP i.MX6Q/DL SoC
with the following features:
- DDR3 DRAM
- NAND FLASH (256MiB or 2048MiB)
- microSD socket
- Gateworks System Periperhal Controller
- front panel LED's
- front panel pushbutton
- RS232 connector (2x UARTs)
- Digital I/O connector (I2C/GPIO)
- SPI connector
- u-blox Zoe-M8Q GPS
- LIS2DE12 Accellerometer
- TI CC1352 ARM Cortex-M4 multiprotocol sub-1GHz / 2.4GHz wireless MCU
- On-board brcmfmac WiFi and BT module
- RGMII RJ45 GbE
- 1x MiniPCIe socket with PCIe/USB 2.0
- 1x MiniPCIe socket with USB 2.0 and nanoSIM socket
- Passive PoE and wide-range DC power supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Move board/revision specific dt fixups for WDOG and UHS-I features
so that we can call them early for U-Boot control dt as well.
Additionally drop a deprected non-mainline dt-prop fixup regarding
HDMI input format.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
EEPROM bits no longer indicate support for NAND so instead use
hard-coded value from board config struct.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Only one dtb is currently supported, so match with imx6-colibri.
Signed-off-by: Ming Liu <ming.liu@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
If config block support is enabled, USB gadget modes unconditionally
use Toradex Product ID as USB PID. Some applications might prefer a
different and/or static USB PID. Add a Kconfig configuration option
to descide whether to use USB PID from config block or the fallback
config option CONFIG_G_DNL_PRODUCT_NUM.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
In case USB serial downloader has been used to load U-Boot start the
serial download protocol (SDP) emulation. This allows to download
complete images such as Toradex Easy Installer over USB SDP as well.
This code uses the boot ROM provided boot information to reliably
detect USB serial downloader.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The bootparams do not have to be at fixed location, they can be
dynamically mallocated instead. Make it so to get rid of another
fixed assignment.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Biju Das <biju.das.jz@bp.renesas.com>
Cc: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
The main reason for this to be implemented is capsule update.
Two memories are supported and tested which is MMC FAT based and QSPI
based.
For creating capsule these commands are used:
./tools/mkeficapsule --raw spl/boot.bin --index 1 capsule1.bin
./tools/mkeficapsule --raw u-boot.itb --index 2 capsule2.bin
Then transfer to SD card where these commands run:
load mmc 0 10000000 capsule1.bin
efidebug capsule update -v 10000000
load mmc 0 10000000 capsule2.bin
efidebug capsule update -v 10000000
Depends on the boot device used are binaries loaded to qspi or mmc fat
partition.
Also multiboot register is handled to make sure that the same location(id)
is used as image which is upgraded.
Two locations are used by purpose for SPL flow. If only boot.bin is used
create only one capsule.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When U-Boot runs in EL2 there is no access to csu_base registers that's why
this has to be done via firmware interface to find out multi boot register
value. Till now this function is called only from SPL in EL3.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change multi_boot() to return multiboot value and move print out of this
function and let this function to be used by other functions without
duplicating message.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When env_set() is called there is no need to allocate memory for variable
which is already saved that's why free it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Move the PSCI runtime code for H3/A23/A33 into SRAM
- Pick the environment from the actual MMC boot device (SD card vs.
eMMC)
- Plus a small improvement from Icenowy, just for good measure.
Currently, the environment is always stored in eMMC if eMMC is enabled
in the config. This means images written to SD and eMMC will cross-
contaminate their environments unless the configuration is changed.
By dropping the device number from the environment location string and
implementing mmc_get_env_dev, we will always use the environment from
the boot device when booting from SD/eMMC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In DM Ethernet, the old "egiga0" and 'egiga1" names are no longer valid,
so replace these with Ethernet PHY names from device tree. Also, read
Ethernet PHY address for each port from device tree.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The gdsys a38x config file (controlcenterdc_defconfig) uses BootROM to
load U-Boot proper.
Since it is now possible to do this via U-Boot SPL framework, we do not
need to provide custom spl_board_init() which calls return_to_bootrom().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that proper load and execution addresses are set in v1 kwbimage we
can use it for loading and booting U-Boot proper.
Use the new spl_parse_board_header() function to implement parsing the
kwbimage v1 header. Use information from this header to locate offset and
size of the U-Boot proper binary, instead of using the legacy U-Boot
header which is prepended to the U-Boot proper binary stored at fixed
offset. This has the advantage that we do not need to relay on legacy
U-Boot header anymore and therefore U-Boot proper binary can be stored at
any offset, as is the case when loading & booting U-Boot proper by
BootROM. The CONFIG_SYS_U_BOOT_OFFS option is therefore not used by SPL
code anymore.
Also allow to compile U-Boot SPL without CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_MMC_SUPPORT or CONFIG_SPL_SATA_SUPPORT set. In this case
BootROM is used for loading and executing U-Boot proper. This reduces the
size of U-Boot's SPL image. By default these config options are enabled
and so BootROM loading is not used. In some cases BootROM reads from SPI
NOR at lower speed than U-Boot SPL. So people can decide whether they
want to have smaller SPL binary at the cost of slower boot.
Therefore dependency on CONFIG_SPL_DM_SPI, CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_SPI_LOAD, CONFIG_SPL_SPI_SUPPORT, CONFIG_SPL_DM_GPIO,
CONFIG_SPL_DM_MMC, CONFIG_SPL_GPIO_SUPPORT, CONFIG_SPL_LIBDISK_SUPPORT,
CONFIG_SPL_MMC_SUPPORT, CONFIG_SPL_SATA_SUPPORT and
CONFIG_SPL_LIBDISK_SUPPORT is changed from strict to related "imply"
(which can be selectivelly turned off and causes booting via BootROM).
Options CONFIG_SYS_SPI_U_BOOT_OFFS,
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR and
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET have to to be set to
zero as they define the location where kwbimage header starts. It is the
location where BootROM expects start of the kwbimage from which it reads,
parses and executes SPL part. The same applies to option
CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR, which has to be set to one.
Update all config files to set correct values of these options and set
CONFIG_SYS_U_BOOT_OFFS to the correct value - the offset where U-Boot
proper starts.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The PADCONFIG_202 register (0x02621328) is affected by the locking
of the RSTMUX8 register (0x02620328), and so cannot be configured
in kernel. This has been confirmed as a hardware bug and affects
all K2G SoCs.
Setup the pinmux for this pin before locking the RSTMUX8 register
to allow the ICSS1 PRU1 Ethernet PHY port to work properly. The
workaround was added only for the K2G-ICE board to configure the
pins needed for the PRUSS Ethernet usecase.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726232248.24395-1-s-anna@ti.com
Align reset_cpu function with the next prototypes in
sysreset.h or in cpu_func.h to solve compilation issue:
void reset_cpu(void);
This patch solves the prototype conflict when cpu_func.h is
included.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
It is quite confusing that CONFIG_SYS_I2C selects the legacy I2C and
CONFIG_DM_I2C selects the current I2C. The deadline to migrate I2C is less
than a year away.
Also we want to have a CONFIG_I2C for U-Boot proper just like we have
CONFIG_SPL_I2C for SPL, so we can simplify the Makefile rules.
Rename this symbol so it is clear it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
need return -1 if boot source is not EMMC or SD ( for example it will be
useful if we have multy env sources configuration and device was booted
from SPI flash and env need read from SPI not from mmc )
Signed-off-by: Artem Lapkin <art@khadas.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
When a push-button is released and PA13/PA14 are defined as input (high-Z)
the LED should not be active as the circuit is open but a small current
leak through PCB or push-button close the circuit and allows a small LED
bias giving erroneous level voltage.
So it is recommended to activate an internal pull-up in order to clearly
fix the voltage at PA13/PA14 when button is released and to wait
a short delay before to read the GPIO value only when the pull-up is
correctly configured.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move j721e document from board/ti/j721e/README to
doc/board/ti/j721e_evm.rst after converting it to RST format.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-20-kishon@ti.com
Add support for probing and configuring Torrent serdes on J7200.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-11-kishon@ti.com
This device tree is imported from Linux 5.13.1 and enabled via the
am335x board file and the am335x evm defconfig.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Add a bus driver for this and use it to configure the bus parameters for
the Ethernet interface. Drop the old pre-driver-model code.
Switch over to use driver model for Ethernet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The SPL can also be compiled with sysreset drivers just fine, so
update the condition to cater for that option.
The same change was done by commit efa1a62ad2 ("ARM: imx8m: Do not define
do_reset() if sysreset is enabled").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The system refuses to boot without any environment, so return ENVL_NOWHERE when
there's nowhere to store the environment instead of ENVL_UNKNOWN.
This fixes that the board won't boot from eMMC when CONFIG_ENV_IS_IN_FAT is not
defined, for example. Similar for other combinations.
Fixes: 1025bd098a "xilinx: zynqmp: Add support for saving variables"
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Split arasan_zynqmp_set_tapdelay() to handle input and output tapdelays
separately. This is required to handle zero values for ITAP and OTAP
values. If we dont split, we will have to remove the if() in the
function, which makes ITAP values to be overwritten when OTAP values are
called to set and vice-versa.
Restrict tap_delay value calculated to max allowed 8 bits for ITAP and 6
bits for OTAP for ZynqMP.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At the moment pressing the volume down key does not actually launch
fastboot. This is because setting "bootdelay" to "-1" actually
disables autoboot and drops to the U-Boot console. It does not execute
the "bootcmd".
The correct value for "bootdelay" here would be "-2", which disables
the delay and key checking and would immediately execute the "bootcmd".
However, even better in this case is using "preboot" to trigger Fastboot.
The advantage is that running "fastboot continue" will actually continue
the autoboot process instead of ending up in the U-Boot shell.
Also make sure to unset "preboot" again immediately in case the user
saves the environment after triggering fastboot.
Cc: Ramon Fried <rfried.dev@gmail.com>
Fixes: aa043ee91a ("db410c: automatically launch fastboot")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
At the moment the U-Boot port for the DragonBoard 410c is designed
to be loaded as an Android boot image after Qualcomm's Little Kernel (LK)
bootloader. This is simple to set up but LK is redundant in this case,
since everything done by LK can be also done directly by U-Boot.
Dropping LK entirely has at least the following advantages:
- Easier installation/board code (no need for Android boot images)
- (Slightly) faster boot
- Boot directly in 64-bit without a round trip to 32-bit for LK
So far this was not possible yet because of unsolved problems:
1. Signing tool: The firmware expects a "signed" ELF image with extra
(Qualcomm-specific) ELF headers, usually used for secure boot.
The DragonBoard 410c does not have secure boot by default but the
extra ELF headers are still required.
2. PSCI bug: There seems to be a bug in the PSCI implementation
(part of the TrustZone/tz firmware) that causes all other CPU cores
to be started in 32-bit mode if LK is missing in the boot chain.
This causes Linux to hang early during boot.
There is a solution for both problems now:
1. qtestsign (https://github.com/msm8916-mainline/qtestsign)
can be used as a "signing" tool for U-Boot and other firmware.
2. A workaround for the "PSCI bug" is to execute the TZ syscall when
entering U-Boot. That way PSCI is made aware of the 64-bit switch
and starts all other CPU cores in 64-bit mode as well.
Simplify the dragonboard410c board by removing all the extra code that
is only used to build an Android boot image that can be loaded by LK.
This allows dropping the custom linker script, special image magic,
as well as most of the special build/installation instructions.
CONFIG_REMAKE_ELF is used to build a new ELF image that has both U-Boot
and the appended DTB combined. The resulting u-boot.elf can then be
passed to the "signing" tool (e.g. qtestsign).
The PSCI workaround is placed in the "boot0" hook that is enabled
with CONFIG_ENABLE_ARM_SOC_BOOT0_HOOK. The extra check for EL1 allows
compatibility with custom firmware that enters U-Boot in EL2 or EL3,
e.g. qhypstub (https://github.com/msm8916-mainline/qhypstub).
As a first step these changes apply only to DragonBoard410c.
Similar changes could likely also work for the DragonBoard 820c.
Note that removing LK wouldn't be possible that easily without a lot of
work already done three years ago by Ramon Fried. A lot of missing
initialization, pinctrl etc was already added back then even though
it was not strictly needed yet.
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.
Move the SMMU initialization code into board support
and call it from board_init().
Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Ensure USB hub, PCIe-USB bridge, and ULPI device to be reset
even if the rebooting is without power-cycling.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Create a new function spl_reset_device_by_gpio to reset the device
whose reset pin is connected to the GPIO. Then, using this function
to initialize GEMGXL.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This patch reverts the following commits:
- 4b4159d0f3 ("riscv: dts: add dts for unmatched rev1")
- ffe9a394df ("board: sifive: support spl multi-dtb on unmatched board")
We won't plan to support unmatched that the revision below 3 in u-boot,
so they can be dropped because they might be useless.
Changed in v2:
- rebase codebase to the latest master branch
Signed-off-by: Zong Li <zong.li@sifive.com>
Suggested-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
We wouldn't like to allow user to change the serial number, so remove
the command for changing serial number in EEPROM.
Signed-off-by: Zong Li <zong.li@sifive.com>
Suggested-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
lx2160ardb Rev-C board has i2c node for thermal monitors
connected to different chip offset.
Add device tree fixup to use lx2160ardb dts and apply
thermal node fixups for lx2160ardb Rev-C board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
[sp:thernal->thermal]
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
[Squashed ls2088a patch to fix compilation]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Refactors similar mux code from multiple NXP boards into a common location,
and allows it to be disabled in config.
New config: CONFIG_FSL_USE_PCA9547_MUX to enable PCA9547 mux functionality.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- Marvell SheevaPlug: Convert Ethernet and SATA to Driver Model (Tony)
- Zyxel NSA310S NAS: Convert to Driver Model (Tony)
- Turris_omnia: Add `u-boot-env` NOR partition (Marek)
- Turris_omnia: Fixup MTD partitions in Linux' DTB (Marek)
- Espressobin: Enable 'mtd' command and define SPI NOR partitions (Pali)
- Enabled distro boot for all TI platforms.
- Cleanup for AM335x Guardian Board
- PRUSS rproc on AM65 platform.
- Add PMIC support for J7200
- Misc fixes for Nokia RX-51
# Conflicts:
# arch/arm/mach-omap2/am33xx/Kconfig
Fixup SPI NOR partition nodes in Linux' device tree prior booting Linux.
Linux' devicetree does not contain "u-boot-env" partition and we do not
want to add it there because the address is different between stock
U-Boot and current upstream U-Boot.
Instead we add code that recreates partition nodes from scratch
according to how U-Boot sees them (which is defined in U-Boot's device
tree).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
- In DM Ethernet, the old "egiga0" name is no longer valid, so replace it
with Ethernet PHY name from device tree. Also, Ethernet PHY address
is available so read it from device tree.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
In DM Ethernet, the old "egiga0" name is no longer valid, so replace it
with Ethernet PHY name from device tree. Also, Ethernet PHY address
is available so read it from device tree.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
As the deadline for migration to DM_USB, when using a USB host
controller has now gone two years past the deadline, enforce migration.
This is done by:
- Ensuring that all host controller options (other than the very legacy
old MUSB ones) now select USB_HOST. USB_HOST now enforces DM_USB and
OF_CONTROL.
- Remove other parts of Kconfig logic that had platforms pick DM_USB.
- To keep Kconfig happy, have some select statements test for USB_HOST
as well.
- Re-order some Kconfig entries and menus so that we can cleanly pick
host or gadget roles. For the various HCD options that have platform
glue options, group them together and update dependencies in some
cases.
- As SPL_DM_USB is not required, on platforms that had not yet enabled
it, disable it.
Cc: Marek Vasut <marex@denx.de>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Samuel Holland <samuel@sholland.org>
Cc: FUKAUMI Naoki <naobsd@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
As the logic here is only used when we have a USB host controller, test
on CONFIG_USB_HOST rather than CONFIG_USB in general. This lets us move
towards using CONFIG_USB only as a menu symbol to say that we have some
form of USB, and then USB_HOST or USB_GADGET depending on the role that
USB plays within the build.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is also the last in family remove the related
support as well.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is also the last in family remove the related
support as well.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- mips: malta: convert to PCI DM and ETH DM
-----BEGIN PGP SIGNATURE-----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=wDfz
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2021-07-18' of https://source.denx.de/u-boot/custodians/u-boot-mips
- mips: gardena-smart-gateway: adjust config to new production values
- mips: malta: convert to PCI DM and ETH DM
As almost all peripherals are connected via PCI dependent on the
used core card, PCI setup is always required. Thus run pci_init()
including PCI scanning and probing and core card specific setups
in board_early_init_r().
Also prepare support for dynamically managing the status of the
different PCI DT nodes dependent on used core card via option
CONFIG_OF_BOARD_FIXUP. Before this feature can be enabled,
the call order of the fix_fdt() init hook in board_init_f
needs to be changed. Otherwise rw_fdt_blob points to a read-only
NOR flash address. Thus this options needs to stay disabled
until the board_init_f problem could be solved. This breaks
running the default U-Boot image on real HW using the FPGA core
card but Qemu emulation still works. Currently Qemu is more
important as MIPS CI tests depend on Malta and the deadline
for PCI DM conversion will be enforced soon.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The capsule signature is now part of our DTB. This is problematic when a
user is allowed to change/fixup that DTB from U-Boots command line since he
can overwrite the signature as well.
So Instead of adding the key on the DTB, embed it in the u-boot binary it
self as part of it's .rodata. This assumes that the U-Boot binary we load
is authenticated by a previous boot stage loader.
Reviewed-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Tested-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Setup USB clock in board codes, and enable the DWC3 XHCI and
PHY drivers to make USB3.0 host port working on i.MX8MQ EVK.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Use the device sequence number in boot_instance variable
and no more the SDMMC instance provided by ROM code/TF-A.
After this patch we don't need to define the mmc alias in
device tree, for example:
mmc0 = &sdmmc1;
mmc1 = &sdmmc2;
mmc2 = &sdmmc3;
to have a correct mapping between the ROM code boot device =
"${boot_device}${boot_instance}" and the MMC device in U-Boot.
With this patch the 'mmc0' device (used in mmc commands) is
always used when only one instance sdmmc is activated in device
tree, even if it is only the sdmmc2 or sdmmc3.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable U-Boot bootz command and update env scripts to try loading also
zImage file and to try booting via bootz command.
Update also lowlevel_init.S code for checking validity of zImage magic to
correctly relocate kernel in zImage format.
This change allows U-Boot to directly boot Linux kernel without need for
converting kernel image into U-Boot uImage format.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210618132704.32066-1-pali@kernel.org
Use VENDOR_COREBOOT instead of TARGET_COREBOOT so we can have multiple
coreboot boards, sharing options. Only SYS_CONFIG_NAME needs to be
defined TARGET_COREBOOT.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Set up coral so that it can boot from coreboot, even though it is a
bare-metal build. This helps with testing since the same image can be used
in both cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The BIOS version may not be present, e.g. on a Chrome OS build. Add the
BIOS date as well, so we get some sort of indication of coreboot's
vintage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new 'quiet' argument to mmc_get_op_cond() function which avoids
printing error message when SD/eMMC card is not detected.
Espressobin and mx6cuboxi boards use this function for detecting presence
of eMMC and therefore it is expected and normal that eMMC does not have to
be connected. So error message "Card did not respond to voltage select!"
should be skipped in this case as it is not an error.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Use function mmc_get_op_cond() instead of mmc_init() for detecting presence
of eMMC. Documentation for this function says that it could be used to
detect the presence of SD/eMMC when no card detect logic is available.
This function is also used by mx6cuboxi board for detecting presence of eMMC.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Ensure that 'env default -a' always set correct value to $fdtfile, even
when custom user variable is already stored in non-volatile env storage
(means that env_get("fdtfile") call returns non-NULL value).
As default value is now correctly set like if specified at compile time in
CONFIG_EXTRA_ENV_SETTINGS, there is no need to set $fdtfile explicitly via
env_set("fdtfile", ...) call.
So remove wrong skip based on env_get("fdtfile") and then also unneeded
env_set("fdtfile", ...) call.
Fixes: c4df0f6f31 ("arm: mvebu: Espressobin: Set default value for $fdtfile env variable")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The U-Boot "stemmy" board is mainly intended to simplify booting
mainline Linux on various smartphones from Samsung based on ST-Ericsson
Ux500. While the mainline kernel is working great, there are still some
features missing there. In particular, it is currently not possible to
charge the battery when using the mainline kernel.
This means that it is still necessary to boot the downstream/vendor
kernel from Samsung sometimes to charge the device. That kernel is
ancient, still uses board files + ATAGS instead of device trees and
relies on a strange very long kernel command line hardcoded in the
Samsung bootloader.
Actually, since mainline is booted with device trees there is a very
simple way to make the old downstream kernel work as well: We can
simply take most of the ATAGS passed to U-Boot from the Samsung
bootloader and copy them as-is when booting a kernel without device
tree. That way the long command line and other needed ATAGS are copied
as-is without having to bother with them.
The only exception is the ATAG_INITRD - since the initrd is loaded
by U-Boot, the atag for that should be generated in U-Boot so it points
to the correct address. All other ATAGS are copied as-is and not
generated in U-Boot.
Also use the chance and provide a serial# for U-Boot by parsing the
ATAG_SERIAL that is also passed by the Samsung bootloader.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
At the moment the "stemmy" board attempts to detect the RAM size with
a simple memory test (get_ram_size()). Unfortunately, this does not work
correctly for devices with 768 MiB RAM (e.g. Samsung Galaxy Ace 2
(GT-I8160), "codina"). Reading/writing memory after the 768 MiB RAM
succeeds but actually overwrites some earlier parts of the memory.
For U-Boot this does not result in any major problems, but on Linux
this will eventually lead to strange crashes because of the memory
corruption.
Since the "stemmy" U-Boot port is designed to be chainloaded from
the original Samsung bootloader, the most reliable way to get the
available amount of RAM is to look at the ATAGS passed by the Samsung
bootloader. Fortunately, the header used to generate ATAGS in U-Boot
(asm/setup.h) can also be easily used to parse them.
Also clarify and simplify stemmy.h a bit to make it more clear where
some of the magic values in there are actually coming from.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The default implementation of checkboard() calls the
nxp_board_rev_string() function
to retrieve a character representing the revision number of the board.
However, this
attempt to retrieve the revision number may fail in certain situations or be
otherwise undesirable.
There is already a configuration option to avoid retrieving the
revision number of
the board: CONFIG_NXP_BOARD_REVISION. In fact, if this option is enabled, the
nxp_board_rev_string() function's definition will be omitted entirely,
meaning that the previous implementation of checkboard() would result
in a linker error.
This changeset makes the default implementation of checkboard() respect the
CONFIG_NXP_BOARD_REVISION configuration option, only attempting to retrieve
the board revision number if that option is defined.
Signed-off-by: Cody Gray <cody@codygray.com>
The Gateworks System Controller thermal protection feature will disable
the board primary power supply if the on-board temperature sensor
reaches 86C. In many cases this could occur before the temperature
critical components such as CPU, DRAM, eMMC, and power supplies have
reached their max temperature.
Remove the forced re-enable of thermal protection so that users can
knowingly disable it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks GW7901 is an ARM based single board computer (SBC)
featuring:
- i.MX8M Mini SoC
- LPDDR4 DRAM
- eMMC FLASH
- SPI FRAM
- Gateworks System Controller (GSC)
- Atmel ATECC Crypto Authentication
- USB 2.0
- Microchip GbE Switch
- Multiple multi-protocol RS232/RS485/RS422 Serial ports
- onboard 802.11ac WiFi / BT
- microSD socket
- miniPCIe socket with PCIe, USB 2.0 and dual SIM sockets
- Wide range DC power input
- 802.3at PoE
To add support for this board:
- add dts from Linux (accepted for v5.14)
- add SPL PMIC config
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
