Commit graph

655 commits

Author SHA1 Message Date
Alex G
c19a28bc65 board: am335x/mux: Do not hang when encountering a bad EEPROM
In most cases, the SPL and u-boot.img will be on the same boot media.
Since the SPL was loaded by the boot rom, the pinmux will already have
been configured for this media. This, the board will still be able to
boot successfully, or at least reach the u-boot console, where more
recovery options are available.

I've encountered this on a beaglebone black with a corrupted EEPROM.
Removing this check allowed the board to boot successfully. I've also
seen this on EVM-based boards with an unprogrammed EEPROM. On those
boards, for some reason there were no UART messages. This made it look
as if the SOC was dead.

Remove the hang(), as it is not a fatal error. Also reformat the error
message to be clearer as to the cause. The original message made it
appear as if the wrong binary was being loaded.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-13 15:54:35 -05:00
Nishanth Menon
7774e97aa7 ti: common: board_detect: Return a valid empty string for un-initialized eeprom
Current logic for query of revision, board_name, config returns
NULL. Users of these functions do a direct strncmp to compare.
Unfortunately, as per conventions require two valid strings to compare
against and the current implementation causes a crash when compared
with NULL.

We'd still like to maintain the simplistic usage of these APIs instead
of redundant if (string) res=strncmp(fn(),"cmp",n); flowing all over
the place.

Hence, since the version, name and config is already pre-initialized
with empty string, just dont check for invalid header in the first
place and return the empty string to the caller.

Reported-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Correct was'nt -> wasn't typo]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-31 10:12:21 -04:00
Nishanth Menon
2a78c9e719 ti: common: board_detect: Setup initial default value for config as well
config should have been initialized along with others as defaults.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-31 10:04:21 -04:00
Nishanth Menon
28d624be62 ti: common: board_detect: Replace hardcoded value with macro
We should have used TI_DEAD_EEPROM_MAGIC in the first place.

Fixes: d3b98a9eb9 ("ti: common: dra7: Add standard access for board description EEPROM")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-31 10:04:21 -04:00
Roger Quadros
f411b5cca4 board: am335x: Always set eth/eth1addr environment variable
Ethernet ports might be used in the kernel even if CPSW driver
is disabled at u-boot. So always set ethaddr and eth1addr
environment variable from efuse.

Retain usbnet_devaddr as it is required for SPL USB eth boot.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13 12:25:10 -05:00
Roger Quadros
e607ec993b board: am335x-icev2: add ethernet phy mode detection logic
Both ethernet ports can be used as CPSW ethernet (RMII mode)
or PRU ethernet (MII mode) by setting the jumper near the port.
Read the jumper value and set the pinmux, external mux and
PHY clock accordingly.

As jumper line is overridden by PHY RX_DV pin immediately
after bootstrap (power-up/reset), we have to use GPIO edge
detection to capture the jumper line status.

As u-boot doesn't provide any infrastructure for GPIO edge
detection, we directly access the GPIO registers.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13 12:25:06 -05:00
Mugunthan V N
1053a769fb board: ti: dra7xx: complex definitions should be protected with parentheses
As a standard practice complex definitions should be protected
with parentheses, as it might fail when used in a complex if
statements.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-08 09:33:35 -04:00
Mugunthan V N
e8131386dc ARM: dts: dra72: add rev C evm support
Add DTS support for dra72 evm Rev C which has the following
changes
* Two ethernet ports now instead of the single one in rev B.
* DP83867 ethernet phy instead of DP838865.

Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-08 09:33:35 -04:00
Andrew F. Davis
b0a4eea1a0 board: am33xx-hs: Allow post-processing of FIT image on AM33xx
When CONFIG_FIT_IMAGE_POST_PROCESS or CONFIG_SPL_FIT_IMAGE_POST_PROCESS
is enabled board_fit_image_post_process will be called, add this
function to am33xx boards when CONFIG_TI_SECURE_DEVICE is set to
verify the loaded image.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-10-02 08:10:01 -04:00
Lokesh Vutla
e92a6b2ee3 board: ks2: Enable ECC using detected DDR size
EEC is being enabled based on the ddr size populated by SPD data.
But not all keystone platforms have SPD data to detect ddr3 size.
So, enable ECC using the detected DDR size.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-01 20:05:05 -04:00
Masahiro Yamada
1221ce459d treewide: replace #include <asm/errno.h> with <linux/errno.h>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content.  (both just wrap <asm-generic/errno.h>)

Replace all include directives for <asm/errno.h> with <linux/errno.h>.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-23 17:55:42 -04:00
Masahiro Yamada
63a7578e4e arch, board: squash lines for immediate return
Remove unneeded variables and assignments.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
2016-09-23 17:53:53 -04:00
Simon Glass
696a91f2b0 Convert CONFIG_SPL_YMODEM_SUPPORT to Kconfig
Convert CONFIG_SPL_YMODEM_SUPPORT to Kconfig

Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:23 -04:00
Simon Glass
02e69a5db1 Convert CONFIG_SPL_WATCHDOG_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:23 -04:00
Simon Glass
e00f76cee9 Convert CONFIG_SPL_SERIAL_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:19 -04:00
Simon Glass
2253797d28 Convert CONFIG_SPL_POWER_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:18 -04:00
Simon Glass
d6b9bd8923 Convert CONFIG_SPL_NAND_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:14 -04:00
Simon Glass
1fdf7c64ed Convert CONFIG_SPL_MMC_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:13 -04:00
Simon Glass
cc4288ef42 Convert CONFIG_SPL_LIBGENERIC_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:12 -04:00
Simon Glass
1646eba85c Convert CONFIG_SPL_LIBDISK_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:12 -04:00
Simon Glass
77d2f7f507 Convert CONFIG_SPL_LIBCOMMON_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:11 -04:00
Simon Glass
9c21df1547 Convert CONFIG_SPL_I2C_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:10 -04:00
Simon Glass
53b5bf3c1d Convert CONFIG_SPL_GPIO_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:10 -04:00
Simon Glass
ae56db5f1c Convert CONFIG_SPL_FAT_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:10 -04:00
Simon Glass
75eba2c45e Convert CONFIG_SPL_EXT_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:09 -04:00
Simon Glass
256fe86b60 Convert CONFIG_SPL_ENV_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:08 -04:00
Lokesh Vutla
01c5075506 board: ks2: README: Update to add K2G support
Update the README to add support for K2G EVM. Also
- Add steps on how to use MMC boot
- Fix load address when using CCS
- Update build target to u-boot.bin from u-boot-dtb.bin as all ks2
  platforms uses DT.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-09-07 13:52:20 -04:00
Nishanth Menon
c989166037 board: am57xx: Fix missing check for beagle_x15
When beagleboard-X15 is booted, we see the following log:
Unidentified board claims BBRDX15_ in eeprom header

This is because of the missing check for x15 (the default) and reports
an error for a valid board configuration. Fix the same.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-09-07 08:49:05 -04:00
Nishanth Menon
c0b1d80a10 board: am57xx: MAINTAINERS: Update for current maintainer
Felipe Balbi has move on from TI and the current email ID is no longer
valid. So, replacing with Lokesh.

While at it, update missing config file which was untracked.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-07 08:49:04 -04:00
Tom Rini
584550d76a omap3: Drop omap3_evm_quick_* targets
These config targets were added well before the Kconfig migration began
as a way to demonstrate how to make these platforms work with cut down
features.  At this point in time they no longer serve a good purpose so
remove them.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-08-05 20:53:53 -04:00
Madan Srinivas
e29878fc47 arm: am4x: add U-Boot FIT signing and SPL image post-processing
Modify the SPL build procedure for AM437x high-security (HS) device
variants to create a secure u-boot_HS.img FIT blob that contains U-Boot
and DTB artifacts signed (and optionally encrypted) with a TI-specific
process based on the CONFIG_TI_SECURE_DEVICE config option and the
externally-provided image signing tool.

Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:23 -04:00
Andreas Dannenberg
17c2987336 arm: omap5: add U-Boot FIT signing and SPL image post-processing
Modify the SPL build procedure for AM57xx and DRA7xx high-security (HS)
device variants to create a secure u-boot_HS.img FIT blob that contains
U-Boot and DTB artifacts signed with a TI-specific process based on the
CONFIG_TI_SECURE_DEVICE config option and the externally-provided image
signing tool.

Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:22 -04:00
Lokesh Vutla
df6b506f16 ti_omap5_common: Find right dtb file for DRA72-RevC Evm
DRA72-Evm revC uses dra72-evm-revc.dtb. Update the same in env vatiables.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-07-01 17:42:57 -04:00
Andreas Dannenberg
4aae64c22a ARM: AM437x: Align HS device variant defconfig filename
Align the name of the defconfig file for high-security (HS) device variants
from the AM43xx family of SoCs with the corresponding name used for the
general purpose devices. This allows for easier cross-association of those
files and also provides room to grow from an HS device part number
perspective.

Furthermore, update and cleanup associated MAINTAINERS file.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Madan Srinivas <madans@ti.com>
2016-07-01 17:42:53 -04:00
Peng Fan
d14739ffe1 Kconfig: make NOR_BOOT a common option
Not only am335x supports booting from NOR, i.MX6 SoCs also
supports booting from NOR. Make NOR_BOOT a common
option to let different SoCs share it.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Francois Retief <fgretief@spaceteq.co.za>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-06-27 22:32:07 -04:00
Lokesh Vutla
1736121b24 board: am437x-hs: spl: Select right dtb from fit
Select a right dtb from FIT for am437x-hs platform.

Reported-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13 08:56:38 -04:00
Schuyler Patton
332dddc6a1 ARM: dts: AM572x-IDK Initial Support
Add initial DTS support for AM572-IDK evm.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13 08:56:38 -04:00
Lokesh Vutla
7a0ea589ba board: am57xx: fit: add support for selecting dtb dynamically
FIT allows for a multiple dtb in a single image. SPL needs away to
detect the right dtb to be used. Adding support for the same for am57xx
platforms.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13 08:56:36 -04:00
Lokesh Vutla
165bd7a1cc board: am57xx: Rename TARGET_BEAGLE_X15 as TARGET_AM57XX_EVM
board/am57xx supports all boards based on am57xx. Rename the taget
as TARGET_AM57XX_EVM.

Fixes: 74cc8b097d ("board: ti: beagle_x15: Rename to indicate support for TI am57xx evms")
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13 08:56:36 -04:00
Keerthy
1428d83270 arm: dra7xx: Assign omap_vcores based on board type
Currently omap_vcores which holds pmic data is being assigned based
on the SoC type. PMIC is not a part of SoC. It is logical to
to assign omap_vcores based on board type. Hence over ride the
vcores_init function and assign omap_vcores based on the board type.

Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2016-06-12 13:14:57 -04:00
Lokesh Vutla
ca5599c3fb ARM: DRA7xx: Enable FIT for hs platforms
Use a single defconfig for all DRA7xx hs platforms by enabling FIT and delete
the platform specific defconfigs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-06 13:39:17 -04:00
Lokesh Vutla
e2924e5904 ARM: k2g: Configure reset mux to device reset
BOOTCFG_RSTMUX8 register controls the reset mux associated with the ARM.
Timer5(dedicated to ARM) when used as WatchDog timer, the events it
generates are routed to the above mux.

Following are the 3 events that can controlled bt the reset mux:
- Device Reset
- An interrupt to the ARM_GIC
- An interrupt to the ARM_GIC followed by a device reset.

Right now to give a default watchdog behaviour "Device reset" is
being selected.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
2016-06-02 21:42:19 -04:00
Keerthy
eafd4644c0 arm: am57xx: Fix alignment where necessary
This just fixes alignment for better readability.

Signed-off-by: Keerthy <j-keerthy@ti.com>
2016-06-02 21:42:18 -04:00
Keerthy
d60198dac2 arm: am57xx: Fix omap_vcores assignment for am572x-idk
Currently omap_vcores is wrongly assigned a default value of
beagle_x15_volts. Hence populating a new structure for am572x-idk
and assigning it to omap_vcores in the vcores_init function.

Fixes: c020d355c4 ("board: ti: am57xx: Add support for am572x idk in SPL")
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2016-06-02 21:42:18 -04:00
Anna, Suman
e42523f544 ARM: DRA7: Consolidate voltage macros across different SoCs
The voltage values for each voltage domain at an OPP is identical
across all the SoCs in the DRA7 family. The current code defines
one set of macros for DRA75x/DRA74x SoCs and another set for DRA72x
macros. Consolidate both these sets into a single set.

This is done so as to minimize the number of macros used when voltage
values will be added for other OPPs as well.

Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-02 21:42:17 -04:00
Anna, Suman
27c9596f68 ARM: DRA7: Define common macros for efuse register offsets
Define a set of common macros for the efuse register offsets
(different for each OPP) that are used to get the AVS Class 0
voltage values and ABB configuration values. Assign these
common macros to the register offsets for OPP_NOM by default
for all voltage domains. These common macros can then be
redefined properly to point to the OPP specific efuse register
offset based on the desired OPP to program a specific voltage
domain.

Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-02 21:42:16 -04:00
Roger Quadros
55efadde7e ARM: AM57xx: AM43xx: Fix USB host
CONFIG_USB_XHCI_OMAP can be set for host mode without setting
CONFIG_USB_DWC3 which is meant for gadget mode only.
board_usb_init() was not being defined for CONFIG_USB_XHCI_OMAP
resulting in a data abort on usb start.

Define board_usb_init() for CONFIG_USB_XHCI_OMAP case. Move
gadget specific handling to within CONFIG_USB_DWC3.

Fixes: 6f1af1e358 ("board: ti: invoke clock API to enable and disable clocks")
Signed-off-by: Roger Quadros <rogerq@ti.com>
2016-06-02 21:42:15 -04:00
Lokesh Vutla
3d16389c90 board: am335x: Allow to choose serial device dynamically
Different AM335x based platforms have different serial consoles. As serial
console is Kconfig option a separate defconfig has to be created for each
platform. So pass the serial device dynamically.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:54 -04:00
Lokesh Vutla
73ec696059 ARM: dts: AM335x-ICEv2: Add minimal dts support
Add minimal dts support for AM335x-ICEv2 board

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
2016-05-27 15:47:53 -04:00
Lokesh Vutla
97f3a178b2 board: AM335x-ICEv2: Add cpsw support
In order to enable cpsw on AM335x ICEv2 board, the following needs to be done:

1)There are few on board jumper settings which gives a choice between
cpsw and PRUSS, that needs to be properly selected[1]. Even after selecting
this, there are few GPIOs which control these muxes that needs to be held high.

2) The clock to PHY is provided by a PLL-based clock synthesizer[2] connected
via I2C. This needs to properly programmed and locked for PHY operation.
And PHY needs to be reset before before being used, which is also held by
a GPIO.

3) RMII mode needs to be selected.

[1] http://www.ti.com/lit/zip/tidr336
[2] http://www.ti.com/lit/ds/symlink/cdce913.pdf

Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:52 -04:00
Lokesh Vutla
d8ff4fdb10 board: AM335x-ICEv2: Add DDR data
AM335x ICEv2 contains a 2Gbit(128Mx16) of DDR3 SDRAM(MT41J128M16JT-125),
capable of running at 400MHz. Adding this specific DDR configuration
details running at 400MHz.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:51 -04:00
Lokesh Vutla
866b178bd1 board: AM335x-ICEv2: Add pinmux support
Add necessary pinmux support for AM335x ICEv2 board.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:51 -04:00
Lokesh Vutla
a964332472 board: AM335x-ICEv2: Add epprom support
Similar to other TI's AM335x platforms, AM335x ICEv2 also has an
eeprom populated for its unique identification. Adding this info
so that AM335x ICEv2 specific initialization can be done.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:50 -04:00
Lokesh Vutla
da9d9599ac ARM: dts: AM335x-BBG: Add initial support
Add initial DTS support for AM335x-BBG

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:49 -04:00
Lokesh Vutla
3819ea7063 ARM: dts: AM335x-evmsk: Add initial support
Add initial DTS support for AM335x-evm sk.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:49 -04:00
Lokesh Vutla
80b24fcd30 ARM: AM335x: Enable FIT
Use a single defconfig for all AM335x platforms by enabling FIT

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:47:48 -04:00
Lokesh Vutla
505ea6e82a board: am33xx: fit: add support for selecting dtb dynamically
FIT allows for a multiple dtb in a single image. SPL needs a way to
detect the right dtb to be used. Adding support for the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:47:47 -04:00
Lokesh Vutla
54a92e1ad8 ARM: dts: AM437x-IDK Initial Support
Add initial DTS support for AM437x-IDK evm.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:46 -04:00
Lokesh Vutla
7dd1283048 ARM: dts: AM43x-EPOS Initial Support
Add initial DTS support for AM43-EPOS evm.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:46 -04:00
Lokesh Vutla
4c4e3b3775 ARM: AM43xx: Enable FIT
Use a single defconfig for all AM43xx platforms by enabling FIT and delete
the platform specific defconfigs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:47:45 -04:00
Lokesh Vutla
5a3775a422 board: AM43xx: fit: add support for selecting dtb dynamically
FIT allows for a multiple dtb in a single image. SPL needs a way to
detect the right dtb to be used. Adding support for the same.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:45 -04:00
Lokesh Vutla
cfd921f7cc ARM: DRA7: configs: Remove obsolete configs
Removing:
uart3_defconfig:
Now uart3 can be selected using menuconfig, removing separate
config for uart mode. Doing uart boot is not straight forward as ROM uses
uart3 as default serial console. In order to boot to prompt, concole in both
u-boot and kernel needs to be changed.

qspiboot_defconfig:
The only advantage of enabling QSPI_BOOT is selecting env in QSPI.
Eventually env needs to be selected by menuconfig so removing
qspiboot_defconfig. qspiboot can be done using dra7xx_evm_defconfig.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:45 -04:00
Lokesh Vutla
bd7245849f ARM: DRA7: Enable FIT
Use a single defconfig for all DRA7 platforms by enabling FIT and delete
the platform specific defconfigs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:47:44 -04:00
Lokesh Vutla
09da87dafd board: dra7: fit: add support for selecting dtb dynamically
FIT allows for a multiple dtb in a single image. SPL needs a way to
detect the right dtb to be used. Adding support for the same.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:43 -04:00
Daniel Allred
62a09f0535 ARM: omap5: add ft_board_setup for dra7xx/am57xx
Adds the board specific ft_board_setup() functions that
are called when CONFIG_OF_BOARD_SETUP is defined. These functions
will currently just call the ft_cpu_setup() function.

Adds CONFIG_OF_BOARD_SETUP to the defconfig files
for dra72_evm, dra74_evm, and am57xx_evm.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>

Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:38 -04:00
Madan Srinivas
a5051b727e ti: AM43xx: board: Detect AM43xx HS EVM
Adds code to detect AM43xx HS EVMS - the string in the
I2C EEPROM for HS EVMs differs from GP EVMs. Adds code to
for evm detection, regardless of whether the evm is for
GP or HS parts, and updates board init to use that.

Modifies findfdt command to pick up am437x-gp-evm.dtb for
the HS EVMs also, as the boards are similar except for
some security specific changes around power supply and
enclosure protection.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:35 -04:00
Robert P. J. Day
7ffe3cd62e Delete tests of CONFIG_OF_LIBFDT when testing CONFIG_OF_BOARD_SETUP
Since CONFIG_OF_BOARD_SETUP depends on CONFIG_OF_LIBFDT:

  config OF_BOARD_SETUP
          bool "Set up board-specific details in device tree before boot"
          depends on OF_LIBFDT
          ...

remove superfluous tests of CONFIG_OF_LIBFDT when testing for
CONFIG_OF_BOARD_SETUP.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
[trini: Typo fix: s/ifdefi/ifdef/]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:16 -04:00
Nishanth Menon
e52e334e5c ARM: DRA7: Add ABB setup for all domains
ABB should be initialized for all required domains voltage domain
for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If
we do not do this, kernel configuring just the frequency using the
default boot loader configured voltage can fail on many corner lot
units and has been hard to debug. This specifically is a concern with
DRA7 generation of SoCs since other than VDD_MPU, all other domains
are only permitted to setup the voltages to required OPP only at boot.

Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2016-04-25 15:10:41 -04:00
Nishanth Menon
3708e78c33 ARM: OMAP5/DRA7: Move ABB TXDONE mask to voltage structure
ABB TX_DONE mask will vary depending on ABB module. For example,
3630 never had ABB on IVA domain, while OMAP5 does use ABB on MM domain,
DRA7 has it on all domains with the exception of CORE, RTC.

Hence, move the txdone mask definition over to structure describing
voltage domain.

Signed-off-by: Nishanth Menon <nm@ti.com>
2016-04-25 15:10:39 -04:00
Lokesh Vutla
8f69523213 memory: Move TI_AEMIF config to KCONFIG
Not all Keystone2 devices has AEMIF NAND controller. So adding Kconfig
entry for CONFIG_TI_AEMIF and enabling it in respective defconfigs on
platforms with AEMIF controller.

Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-18 17:11:43 -04:00
Steve Kipisz
c020d355c4 board: ti: am57xx: Add support for am572x idk in SPL
The AM572x-IDK board (Industrial Dev Kit) is a board based on TI's AM5728x
SOC which has a dual core 1.5GHz A15 processor. This board is a development
platform for the Industrial market with:
- 2GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector

The link to the data sheet and TRM can be found here:

http://www.ti.com/product/AM5728

NOTE: DT support is still pending upstream kernel acceptance but we
should be able to get the base system support with this patch.

Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-18 17:11:32 -04:00
Schuyler Patton
5f405e7fa0 board: ti: am57xx: Update EMIF SDRAM 1 and 3 Timings
Update EMIF data based on recommendations from the now standard TI
EMIF tool version 1.1.1 based on 256MBx16 DDR3L Kingston D2516EC4BXGGB
data sheet

Update T_RRD from 5 to 6 based on AM57xx TRM -
Minimum number of DDR cycles from activate to ativate for a different
bank, minus 1.

Update T_CKESR from 4 to 3 based on AM57xx TRM - Minimum number of DDR
clocks cycles for which SDRAM must remain in self refresh, minus 1.

Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-18 17:11:32 -04:00
Daniel Allred
7e52e11f35 am57x: Move CONS_INDEX to Kconfig
- Move the CONS_INDEX selection out of CONFIG_SYS_EXTRA_OPTIONS and
      into Kconfig proper.
    - Edit the relevant am57x configs to remove the now unneeded
      CONFIG_SYS_EXTRA_OPTIONS.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-18 17:11:31 -04:00
Roger Quadros
c3333ded03 board: ti: am57xx: Prevent init_sata() from being called twice
init_sata() is done as part of scsi_init() in
arch/arm/cpu/armv7/omap-common/sata.c so no need to duplicate
it here.

This seems to fix SATA problems in the kernel when CONFIG_TI_PIPE3 is
configured as loadable module.

Cc: Cooper Jr., Franklin <fcooper@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
2016-04-11 20:48:21 -04:00
Dan Murphy
39fbac91e1 board: ti: DRA7: Add DP83867 TI phy for rev c
Enable the TI DP83867 Giga bit phy on the
dra7 rev c board.  The rx and tx internal
delays are need for this board so the usage
of RGMII_ID is required.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01 17:18:07 -04:00
Roger Quadros
92667e89fc board: ti: am57xx: Set ethernet MAC addresses from EEPROM to env
The MAC addresses for the PRU Ethernet ports will be available in the
board EEPROM as an address range. Populate those MAC addresses (if valid)
into the u-boot environment so that they can be passed on to the
device tree during fdt_fixup_ethernet().

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:27 -04:00
Nishanth Menon
8cac14719d board: ti: DRA7: Add DRA72-rev C evm pinmux
Add the pinmux data for rev C evm. This is different from previous
revisions of the platform thanks to the deltas introduced both from
silicon side and from SoC side.

Based on J6EcoES2_EVM_Base_Config-20160309b and PCT-DRA72x-v1.3.0.7 for
SR2.0 silicon.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:16 -04:00
Ravi Babu
6b1c14bb67 board: ti: DRA72: revC evm: Update sdram timing configuration for SR2.0
DDR configuration has changes from SR1.1 based Rev-A/B version of evm
to the SR2.0 based Rev C of the EVM. Rev C evm now uses the higher
density MT41K512M8RH-125-AAT:E (IT) which is of size 2GB.

Update the DDR configuration based on data from EMIF configuration
tool 1.1.1. NOTE: we use eeprom information (ram_size) to update the
configuration.

Tested-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:14 -04:00
Vitaly Andrianov
b8dafa2209 ti: k2g: increase phy autoneg timeout
After power cycle of a K2G EVM dhcp fails due to a auto-negotiation
timeout. This commit increases the timeout to fix the issue.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-22 12:16:07 -04:00
Alexander Graf
50149ea37a efi_loader: Add runtime services
After booting has finished, EFI allows firmware to still interact with the OS
using the "runtime services". These callbacks live in a separate address space,
since they are available long after U-Boot has been overwritten by the OS.

This patch adds enough framework for arbitrary code inside of U-Boot to become
a runtime service with the right section attributes set. For now, we don't make
use of it yet though.

We could maybe in the future map U-boot environment variables to EFI variables
here.

Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-03-15 18:03:10 -04:00
Paul Kocialkowski
3ef56e61c8 omap-common: Rename set_muxconf_regs_essential to set_muxconf_regs
There is no distinction between essential and non-essential mux configuration,
so it doesn't make sense to have an "essential" prefix.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:12:06 -04:00
Paul Kocialkowski
fbf1b08a93 omap_hsmmc: Board-specific TWL6030 MMC power initialization
Boards using the TWL6030 regulator may not all use the LDOs the same way.
Some might also not use MMC1 at all, so VMMC would't have to be enabled.

This delegates TWL6030 MMC power initializations to board-specific functions,
that may still call twl6030_power_mmc_init for the default behavior.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:11:29 -04:00
Lokesh Vutla
26eccf31b3 ARM: DRA72-evm: Update mux and VIRTUAL/MANUAL mode timings
All the mux configurations needs to be done as part of the IODelay
sequence to avoid glitch. Adding all the mux configuration, MANUAL/VIRTUAL
mode configuration as needed for DRA72-evm.

Also update the mux for SD card detect on DRA74-evm.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:52 -04:00
Lokesh Vutla
d468b1781a ARM: DRA7-evm: Update memory info in banks
Updating the memory banks properly so that DT is populated accordingly.
And updating this only after DDR is properly detected by eeprom, so that
git bisect is still maintained.

Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-03-14 19:18:51 -04:00
Lokesh Vutla
c4a2736ca1 ARM: DRA7: EMIF: Add 4GB DDR settings
The REVH and later versions of DRA7-evm uses MICRON MT41K512M16HA-125 memory
chips which is of size 4GB(2GB on EMIF1 and 2GB on EMIF2). Add support for the
same.

Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-03-14 19:18:51 -04:00
Lokesh Vutla
a7638833b3 ARM: DRA7: Move emif settings to board specific files
The newer versions of DRA7 boards has EEPROM populated with DDR
size specified in it. Moving DRA7 specific emif related settings
to board files so that emif settings can be identified based on EEPROM.

Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-03-14 19:18:50 -04:00
Lokesh Vutla
25afe55de5 ARM: DRA7: Enable EEPROM support
Enable EEPROM support for DRA74-evm.

Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-03-14 19:18:50 -04:00
Lokesh Vutla
d3b98a9eb9 ti: common: dra7: Add standard access for board description EEPROM
DRA7 EVM revH and later EVMs have EEPROM populated that can contain board
description information such as name, revision, DDR definition, etc. Adding
support for this EEPROM format.

Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-03-14 19:18:49 -04:00
Lokesh Vutla
11e2b043dc ARM: AM57xx: Update EMIF registers
There are certain EMIF timing failures seen on the some x15 boards. Updating
the EMIF settings to get rid of these timing failures.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-03-14 19:18:49 -04:00
Adam Ford
2f6ed3b89a ARM: Various: Future-proof serial platdata
A few boards still use ns16550_platdata structures, but assume the structure
is going to be in a specific order. By explicitly naming each entry,
this should also help 'future-proof' in the event the structure changes.

Tested on the Logic PD Torpedo + Wireless.

I only changed a handful of devices that used the same syntax as the Logic
board.  Appologies if I missed one or stepped on toes.  Thanks to Derald Woods
and Alexander Graf.

Signed-off-by: Adam Ford <aford173@gmail.com>

V6: Add fix to arch/arm/cpu/armv7/am33xx/board.c

V5: Add fix to arch/arm/cpu/arm926ejs/lpc32xx/devices.c

V4: Fix subject heading

V3: Remove  reg_offset out in all the structs. It was reverted out, and and if
it did exist, it would get initialized to 0 by default.

V2: I hastily copy-pasted the boards without looking at the UART number.
This addresses 3 boards that use UART3 and not UART1.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-03-14 19:18:48 -04:00
Vitaly Andrianov
8efc243741 ARM: keystone2: use detected ddr3a size
Because KS2 u-boot works in 32 bit address space the existing ram_size
global data field cannot be used. The maximum, which the get_ram_size()
can detect is 2GB only. The ft_board_setup() needs the actual ddr3 size
to fix up dtb.

This commit introduces the ddr3_get_size() which uses SPD data to
calculate the ddr3 size. This function replaces the "ddr3_size"
environment variable, which was used to get the SODIMM size.

For platforms, which don't have SODIMM with SPD and ddr3 is populated to
a board a simple ddr3_get_size function that returns ddr3 size has to be
implemented. See hardware-k2l.h

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:45 -04:00
Vitaly Andrianov
d9a76e77c8 ARM: keystone2: use SPD info to configure K2HK and K2E DDR3
This commit replaces hard-coded EMIF and PHY DDR3 configurations for
predefined SODIMMs to a calculated configuration. The SODIMM parameters
are read from SODIMM's SPD and used to calculated the configuration.

The current commit supports calculation for DDR3 with 1600MHz and 1333MHz
only.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:44 -04:00
Lokesh Vutla
ef76ebb1ef ARM: keystone2: K2G: Add support for different arm/device speeds
The maximum device and arm speeds can be determined by reading
EFUSE_BOOTROM register. As there is already a framework for reading this
register, adding support for all possible speeds on k2g devices.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:44 -04:00
Lokesh Vutla
5cd1f6bd7a ARM: keystone2: Allow for board specific speed definitions
Its not compulsory that speed definition should be same on EFUSE_BOOTROM
register for all keystone 2 devices. So, allow for board specific
speed definitions.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:43 -04:00
Kipisz, Steven
212f96f6bd board: ti: AM57xx: Add detection logic for AM57xx-evm
Current AM57xx evm supports both BeagleBoard-X15
(http://beagleboard.org/x15) and AM57xx EVM
(http://www.ti.com/tool/tmdxevm5728).

The AM572x EValuation Module(EVM) provides an affordable platform to
quickly start evaluation of Sitara. ARM Cortex-A15 AM57x Processors
(AM5728, AM5726, AM5718, AM5716) and accelerate development for HMI,
machine vision, networking, medical imaging and many other industrial
applications. This EVM is based on the same BeagleBoard-X15 Chassis
and adds mPCIe, mSATA, LCD, touchscreen, Camera, push button and TI's
wlink8 offering.

Since the EEPROM contents are compatible between the BeagleBoard-X15 and
the AM57xx-evm, we add support for the detection logic to enable
support for various user programmable scripting capability.

NOTE: U-boot configuration is currently a superset of AM57xx evm and
BeagleBoard-X15 and no additional configuration tweaking is needed.

This change also sets up the stage for future support of TI AM57xx EVMs
to the same base bootloader build.

Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:35 -04:00
Nishanth Menon
5f8bb93b23 ti: AM437x: Use generic EEPROM detection logic
Now that we have a generic TI eeprom logic which can be reused across
platforms, reuse the same.

This revision also includes fixes identified by Dave Gerlach
<d-gerlach@ti.com>

Cc: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:34 -04:00
Nishanth Menon
770e68c0a3 ti: AM335x: Use generic EEPROM detection logic
Use the generic EEPROM detection logic instead of duplicating the AM
eeprom logic.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:33 -04:00
Lokesh Vutla
0bea813d00 ARM: omap-common: Add standard access for board description EEPROM
Several TI EVMs have EEPROM that can contain board description information
such as revision, DDR definition, serial number, etc. In just about all
cases, these EEPROM are on the I2C bus and provides us the opportunity
to centralize the generic operations involved.

The on-board EEPROM on the BeagleBone Black, BeagleBone, AM335x EVM,
AM43x GP EVM, AM57xx-evm, BeagleBoard-X15 share the same format.
However, DRA-7* EVMs, OMAP4SDP use a modified format.

We hence introduce logic which is generic between these platforms
without enforcing any specific format. This allows the boards to use the
relevant format for operations that they might choose.

This module will compile for all TI SoC based boards when
CONFIG_TI_I2C_BOARD_DETECT is enabled to have optimal build times for
platforms that require this support.

It is important to note that this logic is fundamental to the board
configuration process such as DDR configuration which is needed in
SPL, hence cannot be part of the standard u-boot driver model (which
is available later in the process). Hence, to aid efficiency, the
eeprom contents are copied over to SRAM scratchpad memory area at the
first invocation to retrieve data.

To prevent churn with cases such as DRA7, where eeprom format maybe
incompatible, we introduce a generic common format in eeprom which
is made available over accessor functions for usage.

Special handling for BBG1 EEPROM had to be introduced thanks to the
weird eeprom rev contents used.

The follow on patches introduce the use of this library for AM335x,
AM437x, and AM57xx.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:33 -04:00
Vignesh R
900e2104d8 ARM : DRA7: Switch QSPI to use MODE-0 at 64MHz
According to Data Manual(SPRS915P) of AM572x, TI QSPI controller on
DRA74 EVM(rev 1.1+) can support up to 64MHz in MODE-0, whereas MODE-3 is
limited to 48MHz. Hence, switch to MODE-0 for better throughput.
Also, add IODelay parameters for the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-15 12:04:46 -05:00
Mugunthan V N
0369008c36 board: ti: ks2_evm: remove board_eth_init when CONFIG_DM_ETH is defined
remove board_eth_init when CONFIG_DM_ETH is defined

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-02-08 10:10:45 -05:00
Bin Meng
a187559e3d Use correct spelling of "U-Boot"
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-06 12:00:59 +01:00
Cooper Jr., Franklin
bc622966c9 ARM: dra7x/am57x: Remove pin input/output config from WAKEUP pins
The WAKEUP_X pins are always an input no matter the pinmux mode.
However, the 18th bit that typical configures a pin as an input is
considered reserved for the WAKEUP_X pins. Therefore, for any WAKEUP
pin remove any configuration that sets that pin as an input. Since
those pins are only inputs remove any output configuration from those
pins.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
2015-11-21 21:50:19 -05:00
Thomas Chou
c7b9686d5d ns16550: unify serial_omap
Unify serial_omap, and use the generic binding.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-11-21 21:50:17 -05:00
robertcnelson@gmail.com
dfd1bb4ec8 board/ti/am335x: add support for BeagleBone Green
SeeedStudio BeagleBone Green (BBG) is clone of the BeagleBone Black (BBB) minus
the HDMI port and addition of two Grove connectors (i2c2 and usart2).

This board can be identified by the 1A value after A335BNLT (BBB) in the at24 eeprom:
1A: [aa 55 33 ee 41 33 33 35  42 4e 4c 54 1a 00 00 00 |.U3.A335BNLT....|]

http://beagleboard.org/green
http://www.seeedstudio.com/wiki/Beaglebone_green

In Mainline Kernel as of:
https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=79a4e64c679d8a0b1037da174e4aea578c80c4e6

Patch tested on BeagleBone Black (rev C) and BeagleBone Green (production model)

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Jason Kridner <jkridner@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-11-18 14:50:07 -05:00
Kipisz, Steven
74cc8b097d board: ti: beagle_x15: Rename to indicate support for TI am57xx evms
BeagleBoard X15 (http://beagleboard.org/x15) support in u-boot does
actually support two different platform configuration offered by
TI. In addition to BeagleBoard X15, it also supports the TMDXEVM5728
(or more commonly known as AM5728-evm).

Information about the TI AM57xx EVM can be found here
http://www.ti.com/tool/tmdxevm5728

The EVM configuration is 1-1 compatible with BeagleBoard X15 with the
additional support for mPCIe, mSATA, LCD, touchscreen, Camera, push
button and TI's wlink8 offering.

Hence, we rename the beagle_x15 directory to am57xx to support TI
EVMs that use the AM57xx processor. By doing this we have common code
reuse. This sets the stage to have a common u-boot image solution for
multiple TI EVMs such as that already done for am335x and am437x. This
sets the stage for upcoming multiple TI EVMs that share the same code
base.

NOTE: Commit eae7ae1853 ("am437x: Add am57xx_evm_defconfig using
CONFIG_DM") introduced DT support for beagle_x15 under am57xx_evm
platform name. However, this ignored the potential confusion arising for
users as a result. To prevent this, existing beagle_x15_defconfig is
renamed as am57xx_evm_nodt_defconfig to denote that this is the "non
device tree" configuration for the same platform. We still retain
am57xx-beagle-x15.dts at this point, since we just require the common
minimum dts.

As a result of this change, users should expect changes in build
procedures('make am57xx_evm_nodt_defconfig' instead of 'make
beagle_x15_defconfig'). Hopefully, this would be a one-time change.

Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-11-18 08:47:03 -05:00
robertcnelson@gmail.com
9606f71002 board/ti/am335x: beaglebone stop muxing i2c1_pin_mux
On the BeagleBone these i2c1 pins are routed to the expanasion header, where
they can be defined as either pr1_usart0_Xxd/pwm0/spi0/i2c1, dont assume i2c1

Fixes: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/313894/1387696

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com>
CC: Tom Rini <trini@konsulko.com>
2015-11-12 13:19:02 -05:00
Tom Rini
d89059beed board/ti: Update MAINTAINERS entries with more boards
A few config files have been added without updating MAINTAINERS.

Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-11-10 09:20:27 -05:00
Mugunthan V N
9f13b6d147 ARM: AM335x: mux: change mmc0 cd pinmux from mmc0_sdcd to gpio
Currently omap_hsmmc driver doesn't use sdcd pin to detect
whether the card is present or not. Instead the same pin is used
as GPIO to detect card presence. So change the pin mux mode from
mmc0_sdcd to gpio0_6.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:44:03 -04:00
Lokesh Vutla
b9ca4ab453 ARM: k2g: Add config file
Add config file for k2g

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
2015-10-22 14:22:27 -04:00
Lokesh Vutla
83b9bf11fe ARM: k2g: Enable SPI flash
GPIO1_9 controls SPI flash on k2g evm.
So make GPIO1_9 as output pin, inorder to use SPI.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22 14:22:26 -04:00
Roger Quadros
3b68939fa0 ARM: k2g: add SD card and eMMC support
Add MMC support for k2g

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22 14:22:25 -04:00
Vitaly Andrianov
91266ccbb2 ARM: k2g: Add Ethernet Support
Add Ethernet support for tftp support

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22 14:22:24 -04:00
Mugunthan V N
bf7bd4e725 driver: net: keystone_net: fix phy mode configuration
Phy mode is a board property and it can be different between
multiple board and ports, so it should not be hardcoded in
driver to one specific mode. So adding a field in eth_priv_t
structure to pass phy mode to driver.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22 14:22:22 -04:00
Vitaly Andrianov
dd78b8cf30 ARM: k2g: Add pin mux data
Add pin mux data for k2g-evm

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22 14:22:19 -04:00
Vitaly Andrianov
235dd6e8d1 ARM: k2g: Add ddr3 info
Add ddr3 related info

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22 14:22:18 -04:00
Vitaly Andrianov
e6d71e1ca5 ARM: k2g: Add clock information
Add clock information for Galileo

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22 14:22:16 -04:00
Vitaly Andrianov
bda920c65e ARM: k2g: Add pll data
Add pll data for k2g

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22 14:22:15 -04:00
Lokesh Vutla
f9c4a51c3e ARM: k2g: Add kconfig support
Add Kconfig support

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22 14:22:13 -04:00
Lokesh Vutla
1985abe207 ARM: keystone2: Use dtb images by default
Now that OF_CONTROL is enabled on all keystone2 platforms,
build the default images with DT.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22 14:22:11 -04:00
Mugunthan V N
bd83e3df45 am335x_evm: prepare for eth driver model support
Prepare board file so that ethernet registration are
commented for DM conversion

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:18:33 -04:00
Paul Kocialkowski
679f82c349 omap-common: Common function to display die id, replacing omap3-specific version
This introduces omap_die_id_display to display the full die id.
There is no need to store it in an environment variable, that no boot script
is using anyway.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:18:30 -04:00
Paul Kocialkowski
07815eb9f3 omap-common: Common serial and usbethaddr functions based on die id
Now that we have a common prototype to grab the omap die id, functions to figure
out a serial number and usb ethernet address can use it directly.
Those also get an omap_die_id prefix for better consistency.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:17:22 -04:00
Paul Kocialkowski
9fd5401659 omap5: omap_die_id support
This introduces omap5 support for omap_die_id, which matches the common
omap_die_id definition. It replaces board-specific code to grab the die id bits.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:17:21 -04:00
Paul Kocialkowski
987a40d52e omap4: omap_die_id support
This introduces omap4 support for omap_die_id, which matches the common
omap_die_id definition. It replaces board-specific code to grab the die id bits.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:17:20 -04:00
Paul Kocialkowski
b50a768528 omap3: omap_die_id support
This replaces the previous get_dieid definition with omap_die_id, that matches
the common omap_die_id definition.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:17:18 -04:00
dbatzle@dcbcyber.com
eda1dfafb3 ARM Fix pandaboard es and a4 revision ID
board_name environment variable was not getting set correctly for Pandaboard A4 and ES

Signed-off-by: David Batzle <dbatzle@dcbcyber.com>
CC: Albert Aribaud <albert.u.boot@aribaud.net>; Tom Rini <trini@ti.com>; Peter Robinson <pbrobinson@gmail.com>
2015-10-22 14:17:16 -04:00
Lokesh Vutla
8626cb8021 ARM: k2e/l: Apply WA for selecting PA clock source
On keystone2 Lamarr and Edison platforms, the PA clocksource
mux in PLL REG1, can be changed only after enabling its clock
domain.
So selecting the output of PASS PLL as input to PA only after
enabling the clockdomain.
This is as per the debug done by "Vitaly Andrianov <vitalya@ti.com>"
and based on the previous work done by "Hao Zhang <hzhang@ti.com>"

Fixes: d634a0775bcf ("ARM: keystone2: Cleanup PLL init code")
Reported-by: Vitaly Andrianov <vitalya@ti.com>
Tested-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-17 20:16:13 -04:00
Tom Rini
f458c8dac4 ti816x: Switch to SYS_GENERIC_BOARD
Tested on my TI186x rev E. (PG2.0) and take over maintainership.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2015-09-15 13:55:23 -04:00
Tom Rini
aeca15dcb3 ti814x_evm: Switch to SYS_GENERIC_BOARD
Take over maintainership as well.  Not tested as PG2.0 (which I have)
needs additional work over PG1.0 (which Matt has).

Cc: Matt Porter <mporter@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2015-09-15 13:55:22 -04:00
Simon Glass
93b25c0813 arm: Remove omap3_sdp3430 board
This board has not been converted to generic board by the deadline.
Remove it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-11 14:56:52 -04:00
Kishon Vijay Abraham I
6f1af1e358 board: ti: invoke clock API to enable and disable clocks
invoke enable_usb_clocks during board_usb_init and disable_usb_clocks
during board_usb_exit to enable and disable clocks respectively.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:22 -04:00
Kishon Vijay Abraham I
7ba792c044 board: ti: OMAP5: added USB initializtion code
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in omap5 board file that
can be invoked by various gadget drivers.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:21 -04:00
Kishon Vijay Abraham I
7c379aaa03 board: ti: beagle_x15: added USB initializtion code
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in beagle_x15 board file that
can be invoked by various gadget drivers.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:20 -04:00
Kishon Vijay Abraham I
03c128c949 board: ti: remove duplicate initialization of vbus_id_status
vbus_id_status is initialized in board_usb_init. So remove it
while creating dwc3_device objects.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:20 -04:00
Lokesh Vutla
76b3f195e9 ARM: k2l: Fix device speeds
ARM supported speeds and init value of core_pll for SDP1200
are programmed wrong as part for the device speed cleanups.
Fixing it here.
Thanks to "Vitaly Andrianov <vitalya@ti.com>" for bisecting this issue

Fixes: c37ed9f11b61 ("ARM: keystone2: Fix dev and arm speed detection")
Tested-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-08-28 12:33:16 -04:00
Lokesh Vutla
be8ce70c02 ARM: keystone2: Update README
Update README to include uart boot mode support and makefile
changes.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-08-28 12:33:15 -04:00
Lokesh Vutla
5f586e9fa1 ARM: keystone2: Rename u-boot-nand.gph to MLO
NAND boot mode, ROM expects an image with a gp header in the
beginning and an 8bytes filled with zeros at the end. The same is
true for SD boot on K2G platforms but the file name should be MLO.

Renaming u-boot-nand.gph to MLO, so that same image can be used for
NAND and SD boots. And also not including all the u-boot only images
under CONFIG_SPL_BUILD.

Reported-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-08-28 12:33:15 -04:00
Nishanth Menon
76cff2b108 ARM: DRA74-evm: Use SMA_1 spare register to workaround DP83865 phy on SR2.0
DP83865 ethernet phy used on DRA74x-evm is quirky and the datasheet
provided IODELAY values for standard RGMII phys do not work.

Silicon Revision(SR) 2.0 provides an alternative bit configuration
that allows us to do a "gross adjustment" to launch the data off a
different internal clock edge. Manual IO Delay overrides are still
necessary to fine tune the clock-to-data delays. This is a necessary
workaround for the quirky ethernet Phy we have on the platform.

NOTE: SMA registers are spare "kitchen sink" registers that does
contain bits for other workaround as necessary as well. Hence the
control for the same is introduced in a generic SoC specific, board
generic location.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:13 -04:00
Nishanth Menon
0358923409 ARM: DRA74-evm: Add iodelay values for SR2.0
Silicon revision 2.0 has new signal routing hence has an updated set of
iodelay parameters to be used. Update the configuration for the same.
Padmux remains the same.

Based on data from VayuES2_EVM_Base_Config-20150807.

NOTE: With respect to the RGMII values, the Manual IODelay values
are used for the fine adjusments needed to meet the tight RGMII
specification.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:13 -04:00
Tom Rini
b4c4fec300 dra7xx: Move CONS_INDEX to Kconfig and enable CONFIG_SPL_STACK_ADDR
- Move the CONS_INDEX selection out of CONFIG_SYS_EXTRA_OPTIONS and
  into Kconfig proper.
- While in here, enable CONFIG_SPL_STACK_ADDR

Signed-off-by: Tom Rini <trini@konsulko.com>
2015-08-12 20:48:07 -04:00
Lokesh Vutla
7531122e5c ARM: keystone2: Remove unsed external clocks
Remove unused external clocks and make a common definition
for all keystone platforms.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-08-12 20:47:54 -04:00
Lokesh Vutla
94069301ba ARM: keystone2: Cleanup init_pll definition
This is just a cosmetic change that makes
the calling of pll init code looks much cleaner.

Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-08-12 20:47:53 -04:00
Lokesh Vutla
7b50e1599f ARM: keystone2: Fix dev and arm speed detection
Use common devspeed and armspeed definitions.
Also fix reading efuse bootrom register.

Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-08-12 20:47:52 -04:00
Lokesh Vutla
c321a23624 ARM: keystone2: Cleanup PLL init code
There are two types of PLL for all keystone platforms:
Main PLL, Secondary PLL. Instead of duplicating the same definition
for each secondary PLL, have a common function which does
initialization for both PLLs. And also add proper register
definitions.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-08-12 20:47:52 -04:00
Paul Kocialkowski
95de1e2f26 usb: musb-new: CONFIG_MUSB prefix replacement with CONFIG_USB_MUSB
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-08-05 17:20:34 +02:00
Nishanth Menon
59d4cd2297 board: ks2_evm: get rid of bogus CONFIG_LINUX_BOOT_PARAM_ADDR
CONFIG_LINUX_BOOT_PARAM_ADDR is not a valid configuration option. Do
just like what the rest of the world does.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-By: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2015-07-27 15:02:18 -04:00
Nishanth Menon
3c963d2a44 board: ks2: README: fix typos
Fix up a few typos in documentation.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Murali Karicheri <m-karicheri2@ti.com>
2015-07-27 15:02:11 -04:00
Roger Quadros
16fc0f8ee3 ARM: beagle_x15: prevent DCAN1 _wait_target_disable failure in kernel
If board is booted with transitions happening on DCAN1 pins then
the following warning is seen in the kernel at boot when the
hwmod layer initializes.

"omap_hwmod: dcan1: _wait_target_disable failed"

This is because DCAN1 module's SWAKEUP mechanism is broken
and it fails to correctly turn OFF if it sees a transition on the
DCAN1 pins. Suggested workaround is to keep DCAN1 pins in safe mode
while enabling/disabling DCAN1 module.

The hwmod layer enables and disables all modules at boot
and we have no opportunity to put the DCAN1 pins in safe mode
at that point.

DCAN1 is not used by u-boot so it doesn't matter to it if these
pins are in safe mode. The kernel driver correctly configures
the right mode when DCAN1 is active.

Signed-off-by: Roger Quadros <rogerq@ti.com>
[trini: s/PULLUP/PULL_UP/ based on DRA7xx EVM version of this patch]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-07-08 21:51:16 -04:00
Roger Quadros
a5878f1933 ARM: DRA7-evm: prevent DCAN1 _wait_target_disable failure in kernel
If board is booted with transitions happening on DCAN1 pins then
the following warning is seen in the kernel at boot when the
hwmod layer initializes.

"omap_hwmod: dcan1: _wait_target_disable failed"

This is because DCAN1 module's SWAKEUP mechanism is broken
and it fails to correctly turn OFF if it sees a transition on the
DCAN1 pins. Suggested workaround is to keep DCAN1 pins in safe mode
while enabling/disabling DCAN1 module.

The hwmod layer enables and disables all modules at boot
and we have no opportunity to put the DCAN1 pins in safe mode
at that point.

DCAN1 is not used by u-boot so it doesn't matter to it if these
pins are in safe mode. The kernel driver correctly configures
the right mode when DCAN1 is active.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2015-07-08 18:26:42 -04:00
Mugunthan V N
0a888f584c ARM: DRA72x: fix io delay calibration for ethernet
we currently use in-development IODelay values for DRA72x which are
proposed in the data sheet, however, DRA72x EVM uses DP83865 ethernet
Phy over RGMII. The PHY characteristics and routing choices made on
the EVM, make the current iodelay values fail ethernet communication.

Instead, we need to choose custom values for DRA72x-evm specifically
designed for the PHY and routing on the platform for ethernet to
function.

Cc: Nishanth Menon <nm@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-07-07 20:15:52 -04:00