ARM: keystone2: Rename u-boot-nand.gph to MLO

NAND boot mode, ROM expects an image with a gp header in the
beginning and an 8bytes filled with zeros at the end. The same is
true for SD boot on K2G platforms but the file name should be MLO.

Renaming u-boot-nand.gph to MLO, so that same image can be used for
NAND and SD boots. And also not including all the u-boot only images
under CONFIG_SPL_BUILD.

Reported-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This commit is contained in:
Lokesh Vutla 2015-08-17 19:54:50 +05:30 committed by Tom Rini
parent cd43ddc019
commit 5f586e9fa1
2 changed files with 9 additions and 7 deletions

View file

@ -15,8 +15,10 @@ OBJCOPYFLAGS_u-boot-spi.gph = -I binary -O binary --pad-to=$(CONFIG_SPL_PAD_TO)
u-boot-spi.gph: spl/u-boot-spl.gph u-boot.img FORCE
$(call if_changed,pad_cat)
MKIMAGEFLAGS_u-boot-nand.gph = -A $(ARCH) -T gpimage -C none \
ifndef CONFIG_SPL_BUILD
MKIMAGEFLAGS_MLO = -A $(ARCH) -T gpimage -C none \
-a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_TEXT_BASE) -n U-Boot
u-boot-nand.gph: u-boot.bin FORCE
MLO: u-boot.bin FORCE
$(call if_changed,mkimage)
@dd if=/dev/zero bs=8 count=1 2>/dev/null >> $@
endif

View file

@ -61,7 +61,7 @@ Supported image formats:
- u-boot.bin: for loading and running u-boot.bin through Texas instruments
code composure studio (CCS)
- u-boot-spi.gph: gpimage for programming SPI NOR flash for SPI NOR boot
- u-boot-nand.gph: gpimage for programming AEMIF NAND flash for NAND boot
- MLO: gpimage for programming AEMIF NAND flash for NAND boot
Build instructions:
===================
@ -76,9 +76,9 @@ To build u-boot-spi.gph
>make k2hk_evm_defconfig
>make u-boot-spi.gph
To build u-boot-nand.gph
To build MLO
>make k2hk_evm_defconfig
>make u-boot-nand.gph
>make MLO
Load and Run U-Boot on keystone EVMs using CCS
=========================================
@ -157,12 +157,12 @@ instructions:
1. Start CCS and run U-boot as described above.
2. Suspend Target. Select Run -> Suspend from top level menu
CortexA15_1 (Free Running)"
3. Load u-boot-nand.gph binary from build folder on to DDR address 0x87000000
3. Load MLO binary from build folder on to DDR address 0x87000000
through CCS as described in step 2 of "Load and Run U-Boot on K2HK EVM
using CCS", but using address 0x87000000.
4. Free Run the target as described earlier (step 4) to get u-boot prompt
5. At the U-Boot console type following to setup u-boot environment variables.
setenv filesize <size in hex of u-boot-nand.gph rounded to hex 0x10000>
setenv filesize <size in hex of MLO rounded to hex 0x10000>
run burn_uboot_nand
Once u-boot prompt is available, Power OFF the EVM. Set the SW1 dip switch
to "ARM NAND Boot mode" as per instruction at