Since DRA7xx/AM57xx SR1.1 and SR1.0 has errata to limit the frequency of
MMC1 to 96MHz and frequency of MMC2 to 48MHz for AM572x SR1.1, limit the
frequency and disable higher speed modes for those revision.
Also use the recommended IO delays (those tagged with "rev11")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
To debug device tree issues involving 32- and 64-bit platforms, it is useful to
have a generic 64-bit platform available.
Add a version of the sandbox that uses 64-bit integers for its physical
addresses as well as a modified device tree.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Added CONFIG_SYS_TEXT_BASE to configs/sandbox64_defconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
The 'reset' command did not work on Porter because the reset code
was accessing the wrong PMIC address over broken I2C bus driver.
Replace the code with DM-aware code and fix up the PMIC address.
This makes the 'reset' command work again.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Toggle the PHY reset GPIO to bring the ethernet PHY out of reset properly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: This should be moved to the SH ethernet driver, but it's quite
late in the cycle, so this is something to be done in 2018.05.
Due to size limitations of the MERAM, switch U-Boot to SPL.
The SPL is loaded by the SPI_LOADER into MERAM and then loads
U-Boot proper into DRAM. This way U-Boot can freely grow in
size in DRAM, as there is plenty of it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: To update U-Boot, first install u-boot.img to 0x140000 in SPI NOR,
then use the Minimon to flash u-boot-spl.srec using ls,2,e6304000.
To generate u-boot-spl.srec, use objcopy:
arm-linux-gnueabi-objcopy -O srec spl/u-boot-spl u-boot-spl.srec
Commit 958d55f26c ("MAINTAINERS: Take over BCM2835 maintainership") put
me in as maintainer for the RPi soc, but forgot to update the board
MAINTAINERS file.
Add me there too.
Signed-off-by: Alexander Graf <agraf@suse.de>
board_usb_init()/_cleanup() should be in board files and don't have
a place in the xhci-omap driver. Weak versions for
board_usb_init()/_cleanup() already exist in common/usb.c
(for host mode) and drivers/usb/gadget/g_dnl.c (for gadget mode).
Therefore, remove init and cleanup functions from xhci-omap and
implement them in the board files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There is no EMMC symbol in the "enable different boot versions for the
shc board" choice. SHC_EMMC was probably intended.
No functional changes. Kconfig choices fall back on using the first
(visible) symbol in the choice as the default if the default symbol is
not visible.
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which prints the following warning:
warning: the default selection EMMC (undefined) of <choice> (defined at board/bosch/shc/Kconfig:15) is not contained in the choice
I've added a corresponding warning to the C tools too, which is
currently in linux-next: https://patchwork.kernel.org/patch/9983667/
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
The initial implementation of mx6memcal reset the CPU after
running the memory calibration procedure because the generic
board has no information about which boot devices are available.
Now that we have SDP support in SPL, use it to allow a full
U-Boot to be uploaded (i.e. to use "mtest").
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Static variables are not available during board_init_f().
'static uint32_t mx53_dram_size[2];' was used in board specific
dram_init(), dram_init_banksize() and get_effective_memsize() to avoid
multiple calls to get_ram_size().
Reused dram initialization functions from arch/arm/mach-imx/mx5/mx53_dram.c
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Static variables are not available during board_init_f().
'static uint32_t mx53_dram_size[2];' was used in board specific
dram_init(), dram_init_banksize() and get_effective_memsize() to avoid
multiple calls to get_ram_size().
Reused dram initialization functions from arch/arm/mach-imx/mx5/mx53_dram.c
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Move dram_init(), dram_init_banksize() and get_effective_memsize() to
arch/arm/mach-imx/mx5/mx53_dram.c, where it can be reused by m53evk and
mx53loco.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Validate the time at startup:
- in case rtc error add to kernel command line RTC_ERROR
- clamp date to 1-Jan-2036
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Modify configuration to support FIT. Set variable `confidx' from VPD,
in order to load the correct device tree. Modify/simplify U-Boot
environment to support loading FIT image.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Enable the hardware watchdog on bx50v3 to cause it to reset in the event
the board hangs.
Configure GPIO_9 pin as WDOG1_B so that a watchdog timeout results in a
full system reset.
The watchdog is used and reconfigured by systemd approximately 1.7 seconds
into boot. Adding a few seconds for U-Boot and a few more seconds as a
safety margin.
Note that the PCIe controller is _not_ put back into a safe state prior
to board reset. This is a problem if board reset is implemented as CPU
reset.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
There are two I210s on the b850v3 and one on the b450v3 and b650v3.
One is connected to Marvell 88e6240 which is already programmed.
Follow the flow documented in doc/README.enetaddr: set the
enet[0-9]*addr environment variable and let the driver program the
hardware.
The mapping from the driver's index to the environment variable's name
is documented in README: Note for Redundant Ethernet Interfaces. It is
assumed that eth_devices for the controllers on the board are always
indexed in the same order.
The environment variables are removed after programming the hardware
because the variables seem to influence MAC addresses also after U-Boot.
Specifically the MAC address of FEC (MC interface) would be incorrectly
set: 'ethaddr', which maps to the first I210 chip and is set to I210's
default address read from the driver by eth_write_hwaddr in eth_legacy.c
because the variable is undefined (not set even by bx50v3.c), would
result in the eth0 interface's MAC address to be set to I210's default
address.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Instead of programming the hardware directly in the board
implementation, follow the flow documented in doc/README.enetaddr: set
the enet[0-9]*addr environment variable and let the driver program the
hardware.
This avoids duplicating the implementation as it already exists in the
driver (drivers/net/fec_mxc.c: fec_set_hwaddr).
The mapping from the driver's index to the environment variable's name
is documented in README: Note for Redundant Ethernet Interfaces. It is
assumed that eth_devices for the controllers on the board are always
indexed in the same order, i.e. FEC always has the index 2.
The FEC driver does *not* set the flag Set MAC Address on Transmit (bit
set_eth0_mac_address used to do but this is unnecessary as the Linux
networking stack fills in the MAC address.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The change in i2c configuration added to support access to the VPD has
inadvertantly caused access to i2c buses 1 & 2 to be lost. This has
resulted in the configuration for the PMIC to be attempted on the wrong
bus and thus isn't taking effect.
Add the required configuration to return access to buses 1 & 2. In order
to ensure that any users of the bus numbering prior to addition in VPD
patches work, add buses before configuration related to mux on bus 0 and
tweak VPD bus usage to fit new numbering scheme.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected
to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for
Android and video capture application.
notable features:
CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz
Memory Up to 2 GB DDR3-1066
Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4
port 8 bit CSI INPUT MIPI-CSI INPUT
1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc
This patch adds support for Quad/Dual and DualLite/Solo SOM's on
MIPI starter kit with boot from SD and eMMC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlpxesoACgkQykllyylKDCFwngCfZfk2S+c9uJCLh1drA7a+J4Ch
G+MAnA/iRu6/Ihd5UMe4tMK8BU51h0GQ
=Ylul
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2018.03
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
Tested with MTA72ASS8G72PSZ-2S6G1. This is 3DS RDIMM module with x4
DDR chips. LS2088ARDB needs to be modified to connect all DQS signals.
Some of them are grounded by default for x8 chips. Tested with RDIMM
MTA18ASF2G72PDZ on main memory controllers. DP-DDR doesn't support
RDIMM. Dropped related timing table.
Signed-off-by: York Sun <york.sun@nxp.com>
'select n' selects a constant symbol, which is meaningless and has no
effect. Maybe this was meant to be a 'default n', though bool and
tristate symbols already implicitly default to n.
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which does more strict checking here:
kconfiglib.KconfigSyntaxError: board/google/Kconfig:34: Couldn't parse ' select n': expected nonconstant symbol
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move generic functions to common location psu_spl_init.c. Function
declarations are added to private header.
These changes are done in connection to the fact that still files from
HDF can be copied over and compilation should pass.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove SPL_BUILD dependency from zynqmp.c and move it to header file.
Use only one symbol for including psu_init.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psu_init() returns int which wasn't declared and checked.
The patch is fixing function declarations and code to handle return
values properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add check if boot_targets exists in environment and then
generate new_targets env accordingly. Performing strlen on
null address causes it to fail with exception if isolation
is enabled with DDR address zero as secure. It works with out
isolation enabled as zero is valid address but it may lead to
junk values in boot_targets.
This patch fixes the issue by checking return value of env_get
so that it generate boot_targets properly.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zc770-xm011 is x8 width configuration. This FMC card has also x16
variant which requires different ps7_init configuration. This patch adds
it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
checkpatch.pl complains about the spelling of ERR_TIMOUT. Since the
error is only used in a handful of files, we rename the error to
ERR_TIMEOUT.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
The SOM has external pull-up resistors, so let's turn these off.
It was helping reduce some errors when running I2C1 @ 2.6MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
We are switching to a model where our board file can directly fail probing
of serial devices when they're not usable, so remove the current runtime
hack we have.
Signed-off-by: Alexander Graf <agraf@suse.de>
The bcm283x family of SoCs have a GPIO controller that also acts as
pinctrl controller.
This patch introduces a new pinctrl driver that can actually properly mux
devices into their device tree defined pin states and is now the primary
owner of the gpio device. The previous GPIO driver gets moved into a
subdevice of the pinctrl driver, bound to the same OF node.
That way whenever a device asks for pinctrl support, it gets it
automatically from the pinctrl driver and GPIO support is still available
in the normal command line phase.
Signed-off-by: Alexander Graf <agraf@suse.de>
If we include both the rk3288_grf.h and rv1108_grf.h, it will cause the
conflicts of redefinition. Clean the iomux definitions at grf_rv1108.h,
and move them into pinctrl-driver.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
hw_data_init() is called before relocation to initialise hardware data.
Since ctrl is initialized to OMAP_SRAM_SCRATCH_SYS_CTRL in
arch/arm/mach-omap2/am33xx/hw_data.c, the pointer *ctrl will not be
updated during relocation and will hold a stale value.
Therefore call hw_data_init() again after relocation to
reinitialize *ctrl.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Move SYSCFG clock setup into configure_clocks() instead of calling
clock_setup() from board file.
As this clock is only needed in case of ethernet enabled and as
both stm32f4 and stm32f7 are using the Designware ethernet IP,
we use CONFIG_ETH_DESIGNWARE to only enable this clock if needed.
Move the RMII setup from board_early_init_f() to board_init()
to insure that RMII bit is set only when clock driver is initialized.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Thanks to 'commit ba1f966725 ("net: designware: add clock support")'
we don't need anymore to setup the STMMAC clock in board.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Convert the R8A7791 Porter board to DM and DT. This implies mostly
enabling the necessary configuration options and plucking out the
ad-hoc configuration from the board file. Moreover, the pre-reloc
malloc size was increased to allow the clock driver to start up
early without running out of malloc space and the early stack was
moved further up in the DRAM to avoid rewriting U-Boot itself.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The current environment has been hardcoded to an offset that starts to be
an issue given the current size of our main U-Boot binary.
By implementing a custom environment location routine, we can always favor
the FAT-based environment, and fallback to the MMC if we don't find
something in the FAT partition. We also implement the same order when
saving the environment, so that hopefully we can slowly migrate the users
over to FAT-based environment and away from the raw MMC one.
Eventually, and hopefully before we reach that limit again, we will have
most of our users using that setup, and we'll be able to retire the raw
environment, and gain more room for the U-Boot binary.
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When flashing U-Boot on a Boston board using Xilinx Vivado tools, the
final 0x00 byte which ends the .relocs section seems to be skipped &
left in flash as 0xff unless the data contained in the .mcs is padded
out to a 16 byte boundary. Without our final zero byte relocation will
fail with an error about a spurious reloc:
Avoid this problem by padding out the data in the .mcs file to a 16 byte
boundary using srec_cat's -range-pad functionality.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
wait_for_bit callers use the 32 bit LE version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Currently only SD, NAND can be secondary boot sources controlled
by FPGA/CPLD via qixis commands. For SoC like LS1088 IFC-NOR
can be secondary boot source, while QSPI-NOR is the primary.
Add options in qixis to switch to other boot sources including
ifc and emmc.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enables and compiles VID specific functions for SPL.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds the support for VID on LS1088AQDS and LS1088ARDB systems.
It reads the fusesr register and changes the VDD accordingly by adjusting
the voltage via LTC3882 regulator.
This patch also takes care of the special case of 0.9V VDD is present in
fusesr register. In that case,it also changes the SERDES voltage by
disabling the SERDES, changing the SVDD and then re-enabling SERDES.
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds a VID specific API in init_sequence_f and spl code flow
namely init_func_vid which is required to adjust core voltage.
VID specific code is required in spl, hence moving flag CONFIG_VID
out of spl flags.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When VID feature is supported, check the contents of fuse register
and configure DDR operate at 0.9v.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Restructures common driver to support LTC3882 voltage regulator
chip.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moves IR chip (IR36021) specific code in flag to resolve
compilation issue where it is not present. For example,
LS1088A is having a new LTC3882 voltage chip.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds a board specific API namely board_adjust_vdd which
is required to define the board VDD adjust settings.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The SPL doesn't have much room, so in order to support OF_CONTROL
in SPL, we need the extra functionality of SPL_OF_PLATDATA.
Adding these features allows us to remove a small part of code without
losing the serial port during SPL.
Signed-off-by: Adam Ford <aford173@gmail.com>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_CYRUS
CONFIG_IDS8313
CONFIG_MPC8308_P1M
CONFIG_MPC8308RDB
CONFIG_MPC8349EMDS
CONFIG_MPC8349ITXGP
CONFIG_SBC8349
CONFIG_SBC8548
CONFIG_SBC8641D
CONFIG_TQM834X
CONFIG_VE8313
CONFIG_XPEDITE5140
CONFIG_XPEDITE5200
CONFIG_XPEDITE550X
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Mario Six <mario.six@gdsys.cc>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_AMCORE
CONFIG_ASTRO5373L
CONFIG_M52277EVB
CONFIG_M5253DEMO
CONFIG_M5253EVBE
CONFIG_M5275EVB
CONFIG_M54418TWR
CONFIG_STMARK2
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
This adds support for '-machine virt' on AArch64. This is rather simple:
we just add TARGET_QEMU_ARM_xxBIT to select a few different Kconfig
symbols, provide the ARMv8 memory map from the board file and add a new
defconfig based on the 32-bit defconfig.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the board pinmux for AM574x-IDK board using latest PMT[1] and the
board files named am574x_idk_v1p3b_sr2p0 that were auto generated on
13th October, 2017 by "Ahmad Rashed <a-rashed@ti.com>".
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM574x-idk has the following DDR parts attached:
EMIF1: MT41K256M16HA (1GB with ECC)
EMIF2: MT41K256M16HA (1GB without ECC)
Enabling 2GB DDR without interleaving between EMIFs. And
enabling ECC on EMIF1.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
DRA762 comes in two packages:
- ABZ: Pin compatible package with DRA742 with DDR@1333MHz
- ACD: High performance(OPP_PLUS) package with new IPs
Both the above packages uses the same IDCODE hence needs to
differentiate using package information in DIE_ID_2.
Add support for the same. Also update clock, ddr, emif information.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
All ddr3_emif declarations are not used outside ddr3_k2g.c
file. So make all of them as static.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
gpio1_2 is used for HPD interrupt with DRA76's DVI add-on board, so mux
the pin as gpio and PIN_INPUT.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Added support for K2G EVM with FlipChip SoC of which
ARM/DDR3 runs at 1GHz/1066 MT/s. The patch is also
backward compatible with old revision EVM and EVM
with WireBond SoC. Their ARM/DDR3 run at 600MHz/800 MT/s.
The new SoC supports 2 different speeds at 1GHz and 600MHz.
Modyfied the CPU Name to show which SoC is used in the EVM.
Modified the DDR3 configuration to reflect New SoC supports
2 different CPU and DDR3 speeds, 1GHz/1066MT and 600MHz/800MT.
Added new inline function board_it_k2g_g1() for the new FlipChip 1GHz,
and set the u-boot env variable board_name accordingly.
Modified findfdt script in u-boot environment variable to include new k2g board type.
Signed-off-by: Rex Chang <rchang@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
MCAN can be accessed via DCAN1 or DCAN2. Determining which DCAN instance
to use if any at all is done through
CTRL_CORE_CONTROL_SPARE_RW.SEL_ALT_MCAN. Since general pinmuxing is
handled in U-boot. Handle this additional pinmuxing requirement in U-boot
to ensure that MCAN is used by default via the DCAN1 pins.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
[fcooper@ti.com: Update commit message and use DCAN1 not DCAN2 for MCAN]
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Both the "qixis_reset" and esbc_validate" commands can only be used in
full U-Boot so do not build them in SPL. As part of this rework the
qixis code to declare things as static and make use of __weak for
function aliases.
Cc; York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Adjust the FIT build script for 64-bit Allwinner boards to remove the
bogus addresses from the node names and avoid the warnings.
This avoids a warning with recent versions of the dtc tool.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
We dont need to keep copies of the properties that we are going to
fixup since we will be using the dtb provided by the firmware.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
The firmware that runs before u-boot modifies u-boot's device tree
adding the local-mac-address and local-bd-address properties for the
compatibles "qcom,wcnss-bt" and "qcom,wcnss-wlan".
This commit reads that firmware, retrieves the properties and fixups
the device tree that is passed to the kernel before booting.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
This commit adds support for 96Boards Dragonboard820C.
The board is based on APQ8086 Qualcomm Soc, complying with the
96Boards specification.
Features
- 4x Kyro CPU (64 bit) up to 2.15GHz
- USB2.0
- USB3.0
- ISP
- Qualcomm Hexagon DSP
- SD 3.0 (UHS-I)
- UFS 2.0
- Qualcomm Adreno 530 GPU
- GPS
- BT 4.2
- Wi-Fi 2.4GHz, 5GHz (802.11ac)
- PCIe 2.0
- MIPI-CSI, MIPI-DSI
- I2S
U-Boot boots chained from LK (LK implements the fastboot protocol) in
64-bit mode.
For detailed build instructions see readme.txt in the board directory.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Move some of the code for the "lane_bank" and "cpld" code local
commands so that they are not built for SPL as they can only be
used in full U-Boot. This means we can mark a few functions as
static as well now.
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Tested-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add a CONFIG_SPL_BUILD guard around the code for the "mux" command so
it is not included in SPL.
Cc: Qiang Zhao <qiang.zhao@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Qiang Zhao <qiang.zhao@nxp.com>
QMAP value contains information about QSPI chip-selects. These bits
are used to display information of boot device in checkboard()
function.
QMAP value is stored in most significant 3-bits of 8-bit register
brdcfg[0] in Qixis, this patch corrects code to get QMAP bits using
below logic:
(brdcfg[0] >> 5) & 0x7
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove Board Arch print as its value is always constant '1' and does
not contain any important information to display during boot.
Add print to display Board FPGA version.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of chain of trust with confidentiality along with distro
boot, linux kernel image needs to be stored in encrypted form on
ext4 boot partition. So enable CONFIG_CMD_EXT4_WRITE in case of
Secure boot on ARM based platforms.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII
PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Like many other i.MX6 based boards, there are multiple variants of
the cm-fx6 module featuring different SoC variants. Furthermore, the
module can be paired with multiple baseboards.
At the same time modern distribution like Fedora require U-Boot to
select a proper devicetree which depends on the SoC variant and the
baseboard.
Thus, export the SoC variant and the actual board to the environment
following the conventions of other i.MX6 devices (e.g. the NXP boards)
such that the environment can select a devicetree file to load.
For now, we only know for sure that the cm-fx6 module and the SB-fx6m
baseboard amount to a Utilite Computer variant (depending on the SoC).
Further combinations may be added in the future; e.g. CompuLab's
evaluation board once someone can verify the identification string
stored in its eeprom.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Currently mmdc_do_dqs_calibration() and mmdc_do_write_level_calibration()
show the same error message, which is confusing for debugging.
Disambiguate the mmdc_do_dqs_calibration() error message.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
mx6sabresd board uses the following pins for console:
PAD_CSI0_DAT10__UART1_TX_DATA
PAD_CSI0_DAT11__UART1_RX_DATA
,so put it in the same config option as wandboard.
mx6sabreauto board uses the following pins for console:
PAD_KEY_COL0__UART4_TX_DATA
PAD_KEY_ROW0__UART4_RX_DATA
So do not mention sabreauto board as part of the UART1_SD3_DAT6_7 option.
The config option for sabreauto can be added later when needed.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The code for programming the OTP fuses on the PMIC PF0100 can only be
used in full U-Boot, so do not build / link it into SPL.
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
The command can only be used from full U-Boot, so do not build it into
SPL.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The command can only be used from full U-Boot, so do not build it into
SPL.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Because kernel set WDOG_B mux before pad with the common pinctrl
framwork now and wdog reset will be triggered once set WDOG_B mux
with default pad setting, we set pad setting here to workaround this.
Since imx_iomux_v3_setup_pad also set mux before pad setting, we set
as GPIO mux firstly here to workaround it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Enable I2C/MMC/GPIO/REGUALTOR/PMIC/USB DM drivers.
There are some dependency, such as when DM MMC enabled, USB compile error.
Also the i.MX I2C MMC DM driver does not support legacy GPIO interface.
So enable them all together.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Add pfuze dm code, this code could be enabled with CONFIG_DM_PMIC_PFUZE100.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Add nx25-ae250 board to do platform initializations.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
The clock selection is done now from the am335x-fb code, so there is no
more need doing this in the board code.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Actual am335x-fb implementation takes now a real clock frequency instead
a divider. So this component doesn't need to know anymore some base
frequency of the LCDC, we simply provide the pixel-clock frequency.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Using changes in this patch we were able to reduce approx 8k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1088a/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1088a/ls1088a.c to keep
board_early_init_f funcations in case of SPL build.
3. Changes in ls1088a_common.h & ls1088ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds changes necessary to move functionality present in
PowerPC folders with ARM architectures that have DPAA1 QBMan hardware
- Create new board/freescale/common/fsl_portals.c to house shared
device tree fixups for DPAA1 devices with ARM and PowerPC cores
- Add new header file to top includes directory to allow files in
both architectures to grab the function prototypes
- Port inhibit_portals() from PowerPC to ARM. This function is used in
setup to disable interrupts on all QMan and BMan portals. It is
needed because the interrupts are enabled by default for all portals
including unused/uninitialised portals. When the kernel attempts to
go to deep sleep the unused portals prevent it from doing so
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Given gcc-6.1 and later we can now safely have strings discarded when
the functions are unused. This lets us drop certain cases of not
building something so that we don't have the strings brought in when the
code was discarded. Simplify the code now by dropping guards we don't
need now.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board offers :
_ STM32F469NIH6 microcontroller featuring 2 Mbytes of Flash memory
and 324 Kbytes of RAM in BGA216 package
_ On-board ST-LINK/V2-1 SWD debugger, supporting USB reenumeration capability:
_ Mbed-enabled (mbed.org)
_ USB functions: USB virtual COM port, mass storage, debug port
_ 4 inches 800x480 pixel TFT color LCD with MIPI DSI interface and capacitive
touch screen
_ SAI Audio DAC, with a stereo headphone output jack
_ 3 MEMS microphones
_ MicroSD card connector
_ I2C extension connector
_ 4Mx32bit SDRAM
_ 128-Mbit Quad-SPI NOR Flash
_ Reset and wake-up buttons
_ 4 color user LEDs
_ USB OTG FS with Micro-AB connector
_ Three power supply options:
_ Expansion connectors and Arduino™ UNO V3 connectors
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32f7_gpio.c and pinctrl_stm32.c drivers
instead of board GPIO initialization.
Remove stm32_gpio.c which is no more used and migrate
structs stm32_gpio_regs and stm32_gpio_priv into
arch-stm32f4/gpio.h to not break compilation.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM clk_stm32f.c driver instead of dedicated
mach-stm32/stm32f4/clock.c.
Migrate periph_clock defines from stm32_periph.h directly in
CLK driver. These periph_clock defines will be removed when STMMAC,
TIMER2 and SYSCFG drivers will support DM CLK.
Enable also CLK flag.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Remove serial_stm32.c driver and uart init from board file,
use available DM serial_stm32x7.c driver compatible for
STM32F4/F7 and H7 SoCs.
The serial_stm32x7.c driver will be renamed later with a more
generic name as it's shared with all STM32 Socs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32_sdram.c driver instead of board
SDRAM initialization.
For that, enable OF_CONTROL, OF_EMBED and STM32_SDRAM flags.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Support for that board got introduced recently without the maintainers
part. Let's fix that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H3 SoC.
The board has 1GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.
Raspberry Pi B+ like peripherals supported on this board include:
- Power input through micro-USB connector (without USB OTG)
- Native 100 Mbps ethernet using the internal PHY, as opposed to
USB-based on the RPi
- 4x USB 2.0 host ports, directly connected to the SoC, as opposed to
being connected through a USB 2.0 hub on the RPi
- TV and audio output on a 3.5mm TRRS jack
- HDMI output
- Micro-SD card slot
- Standard RPi B+ GPIO header, with the standard peripherals routed to
the same pins.
* 5V, 3.3V power, and ground
* I2C0 on the H3 is routed to I2C1 pins on the RPi header
* I2C1 on the H3 is routed to I2C0 pins on the RPi header
* UART1 on the H3 is routed to UART0 pins on the RPi header
* SPI0 on the H3 is routed to SPI0 pins on the RPi header,
with GPIO pin PA17 replacing the missing Chip Select 1
* I2S1 on the H3 is routed to PCM pins on the RPi header
- Additional peripherals from the H3 are available on different pins.
These include I2S0, JTAG, PWM1, SPDIF, SPI1, and UART3
In addition, there are a number of new features:
- Console UART header
- Consumer IR receiver
- Camera interface (not compatible with RPi)
- Onboard microphone
- eMMC expansion module port
- Heatsink mounting holes
This patch adds defconfig and dts files for this board. The dts file is
the same as the one submitted for inclusion in Linux, with some minor
revisions to match the dtsi file and old EMAC bindings in U-boot.
Since the OTG controller is wired to a USB host port, and the H3 has
proper USB hosts to handle host mode, the MUSB driver is not enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
board/icorem6_rqs/ is forgot to remove while moving
common board files together in
(sha1: 52aaddd6f4)
"i..MX6: engicam: Add imx6q/imx6ul boards for existing boards"
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
commit 20f1471416 ("imx: spl: Update NAND bootmode detection bit")
broke the NAND bootmode detection by checking if
BOOT_CFG1[7:4] == 0x8 for NAND boot mode.
This commit essentially reverts it, while using the IMX6_BMODE_*
macros that were introduced since.
Tables 8-7 & 8-10 from IMX6DQRM say the NAND boot mode selection
is done when BOOT_CFG1[7] is 1, but BOOT_CFG1[6:4] is not
necessarily 0x0 in this case.
Actually, NAND boot mode is when 0x8 <= BOOT_CFG1[7:4] <= 0xf,
like it was in the code before.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Tim Harvey <tharvey@gateworks.com>
This is a virtual "board" that uses configuration files and
Kconfig to define the memory layout used by a real board during
the board bring-up process.
It generates an SPL image that can be loaded using imx_usb or
SB_LOADER.exe.
When run, it will generate a set of calibration constants for
use in either or both a DCD configuration file for boards that
use u-boot.imx or struct mx6_mmdc_calibration for boards that
boot via SPL.
In essence, it is a configurable, open-source variant of the
Freescale ddr-stress tool.
https://community.nxp.com/docs/DOC-105652
File mx6memcal_defconfig configures the board for use with
mx6sabresd or mx6qsabreauto.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
We want to have the same configuration defaults for the RK3368-uQ7
as for the RK3399-Q7: this change reduces the default env-size to
8KiB to ensure that it does not overlap the boot-payload on SD/MMC
configurations.
References: commit fe529e6597 ("rockchip: rk3399-puma: reduce env size to 8kiB")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Khadas VIM is an Open Source DIY Box manufactured by Shenzhen Wesion NOT 'Tomato'
The fix was provided by Khadas Team member 'numbqq'.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This commit clears 'ethaddr' before calling 'smc911x_initialize' to
allow the SROM MAC address to be assigned properly.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
This commit changes the size of the enviroment (for the RK3399-Q7) to
8kiB for all possible locations of the environment (i.e. even when the
environment is saved to SD card).
With the default of 32kiB, the environment overwrites the SPL
stage which lives at 16kiB.
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Reworked commit-message:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The DDR DRAM calibration doesn't work on T-topology sometimes, so disable it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Secure boot is not enabled in warp imximage.cfg, add support for it.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Secure boot is not enabled in mx6slevk imximage.cfg, add support for it.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Currently only imx6sx-sdb.dtb is loaded, but if revA board is used the
correct dtb is imx6sx-sdb-reva.dtb, so make this possible.
While at it, remove an extra 'mmc dev'.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
NXP development boards based on i.MX6/i.MX7 contain the board
revision information stored in the fuses.
Introduce a common function that can be shared by different boards and
convert mx6sabreauto to use this new mechanism.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
