The Micron MT35XU512ABA flash does not support the quad enable bit. But
instead of programming the Quad Enable Require field to 000b ("Device
does not have a QE bit"), it is programmed to 111b ("Reserved").
While this is technically incorrect, it is not reason enough to abort
BFPT parsing. Instead, continue BFPT parsing assuming there is no quad
enable bit present.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Allow flashes to specify a hook to enable octal DTR mode. Use this hook
whenever possible to get optimal transfer speeds.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The xSPI Profile 1.0 table specifies how many dummy cycles and address
bytes are needed for the Read Status Register command in Octal DTR mode.
Use that information to send the correct Read SR command.
Some controllers might have trouble reading just 1 byte in DTR mode. So,
when we are in DTR mode read 2 bytes and discard the second. This shows
no side effects with the two flashes I tested: Micron mt35xu512aba and
Cypress s28hs512t.
Update Read FSR to mimic Read SR because they share the same
characteristics.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This table is indication that the flash is xSPI compliant and hence
supports octal DTR mode. Extract information like the fast read opcode,
the number of dummy cycles needed for a Read Status Register command,
and the number of address bytes needed for a Read Status Register
command.
The default dummy cycles for a fast octal DTR read are set to 20. Since
there is no simple way of determining the dummy cycles needed for the
fast read command, flashes that use a different value should update it
in their flash-specific hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Some devices in DTR mode expect an extra command byte called the
extension. The extension can either be same as the opcode, bitwise
inverse of the opcode, or another additional byte forming a 16-byte
opcode. Get the extension type from the BFPT. For now, only flashes with
"repeat" and "inverse" extensions are supported.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
JESD216 rev D makes BFPT 20 DWORDs. Update the BFPT size define to
reflect that.
The check for rev A or later compared the BFPT header length with the
maximum BFPT length, BFPT_DWORD_MAX. Since BFPT_DWORD_MAX was 16, and so
was the BFPT length for both rev A and B, this check worked fine. But
now, since BFPT_DWORD_MAX is 20, it means this check will also stop BFPT
parsing for rev A or B, since their length is 16.
So, instead check for BFPT_DWORD_MAX_JESD216 to stop BFPT parsing for
the first JESD216 version, and check for BFPT_DWORD_MAX_JESD216B for the
next two versions.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Double Transfer Rate (DTR) is SPI protocol in which data is transferred
on each clock edge as opposed to on each clock cycle. Make
framework-level changes to allow supporting flashes in DTR mode.
Right now, mixed DTR modes are not supported. So, for example a mode
like 4S-4D-4D will not work. All phases need to be either DTR or STR.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Even when spi_nor_write_reg() has no data to write, like when executing
a write enable operation, it sets the data direction to
SPI_MEM_DATA_OUT. This trips up spi_mem_check_buswidth() because it
expects a data phase when there is none. Make sure the data direction is
set to SPI_MEM_NO_DATA when there is no data to write.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The spi-mem layer provides a spi_mem_supports_op() function to check
whether a specific operation is supported by the controller or not.
This is much more accurate than the hwcaps selection logic based on
SPI_{RX,TX}_ flags.
Rework the hwcaps selection logic to use spi_mem_supports_op().
To make sure the build doesn't break for boards not using CONFIG_DM_SPI,
add a simple SPI_{RX,TX}_ based hwcaps selection logic in spi-mem-nodm
similar to spi_mem_default_supports_op(). This change is only
compile-tested.
To avoid SPL size problems on the x530 board, the old hwcaps selection
is still kept around. Leaving the code in-place was getting difficult to
read and understand, so the code is restructured to have it all in one
isolated function. As a result of this, the parameter hwcaps to
spi_nor_setup() is no longer needed. Remove it.
Based on the Linux commit c76f5089796a (mtd: spi-nor: Rework hwcaps
selection for the spi-mem case, 2019-08-06)
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sometimes the information in a flash's SFDP tables is wrong. Sometimes
some information just can't be expressed in the SFDP table. So,
introduce the fixup hooks to allow tailoring settings for a specific
flash.
Three hooks are added: default_init, post_sfdp, and post_bfpt. These
allow tweaking the flash settings at different point in the probe
sequence. Since the hooks reside in nor->info, set that value just
before the call to spi_nor_init_params().
The hooks and at what points they are executed mimics Linux's spi-nor
framework. One major difference is that Linux puts the struct
spi_nor_fixups in nor->info. This is not possible in U-Boot because the
spi-nor-ids list is shared between spi-nor-core.c and spi-nor-tiny.c.
Since spi-nor-tiny shouldn't have those fixup hooks populated, add a
separate function that lets flashes populate their fixup hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
These structures will be used in a later commit inside another structure
definition. Also take the declarations out of the ifdef since they won't
affect the final binary anyway and will be used in a later commit.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
nor->setup() can be used by flashes to configure settings in case they
have any peculiarities that can't be easily expressed by the generic
spi-nor framework. This includes things like different opcodes, dummy
cycles, page size, uniform/non-uniform sector sizes, etc.
Move related declarations to avoid forward declarations.
Inspired by the Linux kernel's setup() hook.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
If a flash chip has more than 16MB capacity but its BFPT reports
BFPT_DWORD1_ADDRESS_BYTES_3_OR_4, the spi-nor framework defaults to 3.
The check in spi_nor_scan() doesn't catch it because addr_width did get
set. This fixes that check.
Ported from Kernel commit 324f78dfb442b82365548b657ec4e6974c677502.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Set up opcode extension and enable/disable DTR mode based on whether the
command is DTR or not.
xSPI flashes can have a 4-byte dummy address associated with some
commands like the Read Status Register command in octal DTR mode. Since
the flash does not support sending the dummy address, we can not use
automatic write completion polling in DTR mode. Further, no write
completion polling makes it impossible to use DAC mode for DTR writes.
In that mode, the controller does not know beforehand how long a write
will be and so it can de-assert Chip Select (CS#) at any time. Once CS#
is de-assert, the flash will go into burning phase. But since the
controller does not do write completion polling, it does not know when
the flash is busy and might send in writes while the flash is not ready.
So, disable write completion polling and make writes go through indirect
mode for DTR writes and let spi-mem take care of polling the SR.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Once the start bit is toggled it takes a small amount of time before it
is internally synchronized. This means we can't start writing during
that part. So add a small delay to allow the bit to be synchronized.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
If the device tree provides a read delay value, use that directly and do
not perform the calibration procedure.
This allows the device tree to over-ride the read delay value in cases
where the read delay value obtained via calibration is incorrect. One
such example is the Cypress Semper flash. It needs a read delay of 4 in
octal DTR mode. But since the calibration procedure is run before the
flash is switched in octal DTR mode, it yields a read delay of 2. A
value of 4 works for both octal DTR and legacy modes.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
spi_mem_default_supports_op() rejects DTR ops by default to ensure that
the controller drivers that haven't been updated with DTR support
continue to reject them. It also makes sure that controllers that don't
support DTR mode at all (which is most of them at the moment) also
reject them.
This means that controller drivers that want to support DTR mode can't
use spi_mem_default_supports_op(). Driver authors have to roll their own
supports_op() function and mimic the buswidth checks. Or even worse,
driver authors might skip it completely or get it wrong.
Add spi_mem_dtr_supports_op(). It provides a basic sanity check for DTR
ops and performs the buswidth requirement check. Move the logic for
checking buswidth in spi_mem_default_supports_op() to a separate
function so the logic is not repeated twice.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
In xSPI mode, flashes expect 2-byte opcodes. The second byte is called
the "command extension". There can be 3 types of extensions in xSPI:
repeat, invert, and hex. When the extension type is "repeat", the same
opcode is sent twice. When it is "invert", the second byte is the
inverse of the opcode. When it is "hex" an additional opcode byte based
is sent with the command whose value can be anything.
So, make opcode a 16-bit value and add a 'nbytes', similar to how
multiple address widths are handled.
All usages of sizeof(op->cmd.opcode) also need to be changed to be
op->cmd.nbytes because that is the actual indicator of opcode size.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Each phase is given a separate 'dtr' field so mixed protocols like
4S-4D-4D can be supported.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add a driver for Macronix SPI controller IP.
This patch referred from linux spi-mxic.c. The difference from the
linux version is described here.
1. To adapt uboot spi framework, modify some functions naming.
2. Remove the incompatible functions of Uboot.
3. Add dummy byte recalculattion function to support dummy buswidth
not align data buswidth operation.(ex: 1-1-4, 1-1-8)
4. Add Octal mode support.
Signed-off-by: Zhengxun <zhengxunli.mxic@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: fixed file permission, comment line, kconfig]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Unlike imx6, on imx7 the USB PHY is described as:
usbphynop1: usbphynop1 {
compatible = "usb-nop-xceiv";
clocks = <&clks IMX7D_USB_PHY1_CLK>;
clock-names = "main_clk";
#phy-cells = <0>;
};
which does not have the 'reg' property.
Do not return an error when the 'reg' property is not found
for the USB PHY.
This fixes USB gadget regression on a imx7s-warp board.
Successfully tested the "ums 0 mmc 0" command on two boards:
imx7s-warp and imx6dl-pico-pi.
Signed-off-by: Fabio Estevam <festevam@denx.de>
On a imx7s-warp board the fdtdec_get_alias_seq() function
always fails.
As priv->portnr is only used on i.MX6, move fdtdec_get_alias_seq()
inside the CONFIG_MX6 block.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Import R8A779A0 V3U PFC tables from Linux 5.12, commit 9f4ad9e425a1
("Linux 5.12") . Add parts of PFC table integration from
pinctrl: renesas: Add R8A779A0 V3U PFC tables
by Hai Pham <hai.pham.ud@renesas.com>" .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The R8A779A0 V3U GPIO block has additional "General Input Enable" INEN
register. Add new R8A779A0 compatible string with a new quirk and also
a handler for this quirk which toggles the INEN register in the right
place. INEN register handling is based on "gpio: renesas: Add R8A779A0
V3U support" by Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add clock tables for R8A779A0 V3U SoC from Linux 5.12,
commit 9f4ad9e425a1 ("Linux 5.12")
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
--
Marek: - Add .reset_modemr_offset
- Sync tables from Linux 5.12
- Rebase on latest u-boot
On R8A779A0 V3U SoC, PLL1 and PLL5 use a divider value
from cpg_pll_configs table while PLL{20,21,30,31,4} use
different control offset. Introduce new types to handle
this and handle those types in the Gen3 clock code.
Based on "clk: renesas: Add support for R8A779A0 V3U PLLn"
by Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The get_mtd_device_nm() function (code imported from Linux) simply
iterates all registered MTD devices and compares the given name with
all MTDs' names.
With SPI_FLASH_MTD enabled U-Boot registers a SPI-NOR as a MTD device
with name identical to the SPI flash chip name (from SPI ID table). Thus
for a board with multiple same SPI-NORs it registers multiple MTDs, but
all with the same name (such as "s25fl164k"). We do not want to change
this behaviour, since such a change could break existing boot scripts,
which can rely on a hardcoded name.
In order to allow somehow to uniqely select a MTD device, change
get_mtd_device_nm() function as such:
- if first character of name is '/', try interpreting it as OF path
- otherwise compare the name with MTDs name and MTDs device name.
In the following example a board has two "s25fl164k" SPI-NORs. They both
have name "s25fl164k", thus cannot be uniquely selected via this name.
With this change, the user can select the second SPI-NOR either with
"spi-nor@1" or "/soc/spi@10600/spi-nor@1".
Example:
=> mtd list
List of MTD devices:
* s25fl164k
- device: spi-nor@0
- parent: spi@10600
- driver: jedec_spi_nor
- path: /soc/spi@10600/spi-nor@0
- type: NOR flash
- block size: 0x1000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000000800000 : "s25fl164k"
* s25fl164k
- device: spi-nor@1
- parent: spi@10600
- driver: jedec_spi_nor
- path: /soc/spi@10600/spi-nor@1
- type: NOR flash
- block size: 0x1000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000000800000 : "s25fl164k"
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
In order for `mtd list` U-Boot command to list SPI NOR devices without
the need to run `sf probe` before, we have to probe SPI NOR devices in
mtd_probe_devices().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
The device_probe() function does the same thing as mtd_probe() and
mtd_probe() is only used in mtd_probe_uclass_mtd_devs(), where the
probing can be made simpler by using uclass_foreach_dev_probe macro.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Fill in mtd->dev member with nor->dev.
This can be used by MTD OF partition parser.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Currently when the SPI_FLASH_MTD config option is enabled, only one SPI
can be registered as MTD at any time - it is the last one probed (since
with old non-DM model only one SPI NOR could be probed at any time).
When DM is enabled, allow for registering multiple SPI NORs as MTDs by
utilizing the nor->mtd structure, which is filled in by spi_nor_scan
anyway, instead of filling a separate struct mtd_info.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Add support for parsing partitions defined in device-trees via the
`partitions` node with `fixed-partitions` compatible.
The `mtdparts`/`mtdids` mechanism takes precedence. If some partitions
are defined for a MTD device via this mechanism, the code won't register
partitions for that MTD device from OF, even if they are defined.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Add function for retrieving full node path of a given ofnode.
This uses np->full_name if OF is live, otherwise a call to
fdt_get_path() is made.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add functions ofnode_get_addr_size_index_notrans(), which is a
non-translating version of ofnode_get_addr_size_index().
Some addresses are not meant to be translated, for example those of MTD
fixed-partitions.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Macronix NAND Flash devices are available in different configurations
and densities.
MX"35" means SPI NAND
MX35"UF" , UF meands 1.8V
MX35LF"2G" , 2G means 2Gbits
MX35LF2G"E4" , E4 means internal ECC and Quad I/O(x4)
MX35UF4GE4AD/MX35UF2GE4AD/MX35UF1GE4AD are 1.8V 4G/2Gbit serial
NAND flash device with 8-bit on-die ECC
https://www.mxic.com.tw/Lists/Datasheet/Attachments/7983/MX35UF4GE4AD,%201.8V,%204Gb,%20v0.00.pdf
MX35UF2GE4AC/MX35UF1GE4AC are 1.8V 2G/1Gbit serial
NAND flash device with 8-bit on-die ECC
https://www.mxic.com.tw/Lists/Datasheet/Attachments/7974/MX35UF2GE4AC,%201.8V,%202Gb,%20v1.0.pdf
Validated via normal(default) and QUAD mode by read, erase, read back,
on Xilinx Zynq PicoZed FPGA board which included Macronix
SPI Host(drivers/spi/spi-mxic.c).
Signed-off-by: Jaime Liao <jaimeliao@mxic.com.tw>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- x86: Discard .note.gnu.property sections
- nvme: Skip block device creation for inactive namespaces
- nvme: Convert NVMe doc to reST, and various minor fixes
A udevice's priv space is cleared in alloc_priv() in the DM core.
Don't do it again in its probe() routine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present there is an offset of one added during the creation of
block device. This can be very confusing as we wanted to encode the
namespace id in the block device name but namespae id cannot be zero.
This changes to use the namespace id directly in the block device
name, eliminating the offset of one effectively.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present for each namespace there is a block device created for it.
There is no issue if the number of supported namespaces reported from
the NVMe device is only 1.
Since QEMU commit 7f0f1acedf15 ("hw/block/nvme: support multiple namespaces"),
the number of supported namespaces reported has been changed from 1
to 256, but not all of them are active namespaces. The actual active
one depends on the QEMU command line parameters. A common case is
that namespace 1 being active and all other 255 being inactive.
If a namespace is inactive, the namespace identify command returns a
zero filled data structure. We can use field NSZE (namespace size) to
decide whether a block device should be created for it.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present the block device creation happens in the NVMe uclass
driver post_probe() phase. In preparation to support multiple
namespaces, we should issue namespace identify before creating
block devices but that touches the underlying hardware hence it
is not appropriate to do such in the uclass driver post_probe().
Let's move it to driver probe() phase instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
AQA (Admin Queue Attributes) register is a dword size with
lower word of ASQS, and higher word of ACQS.
The code set the variable aqa twice, but it is redundant.
Signed-off-by: Wesley Sheng <wesleyshenggit@sina.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Each prp is 8 bytes, calculate the number of prps
per page should just divide page size by 8
there is no need to minus 1
Signed-off-by: Wesley Sheng <wesleyshenggit@sina.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
writel() and co. already include the endian swap; doing the swap twice
is, er, unhelpful.
Tested on a P4080DS, which boots perfectly fine off NVMe with this.
Signed-off-by: David Lamparter <equinox@diac24.net>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Clocking Wizard IP supports clock circuits customized
to your clocking requirements. The wizard support for
dynamically reconfiguring the clocking primitives for
Multiply, Divide, Phase Shift/Offset, or Duty Cycle.
Limited by U-Boot clk uclass without set_phase API, this
patch only provides set_rate to modify the frequency.
Signed-off-by: Zhengxun <zhengxunli.mxic@gmail.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
pca953x also depends on i2c that's why add dependency to Kconfig.
Where GPIO is enabled but I2C compilation error pops up.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The MX66UW2G345G is Macronix Flash with SINGLE and OCTAL I/O. Hence,
add SPI_NOR_OCTAL_READ flag for this flash.
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: change order of id flags]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: zhengxun <zhengxunli.mxic@gmail.com>
This reverts commit 63756575b4.
Since this commit a imx6qdl-pico board boots extremely slowly
in both SPL as well as U-Boot proper.
Fix this regression by reverting the offending commit for now.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Pierre-Jean Texier <texier.pj2@gmail.com>
The data read is not working when using FIFO mode.
From DesignWare databook, when a Data_Transfer_Over (DTO) interrupt is
received, the software should read the remaining data from FIFO.
Add DTO interrupt checking on data read path and clear interrupts before
start reading from FIFO. So, it doesn't clear the next pending
interrupts unintentionally after read from FIFO.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
With a 48MHz input clock, the lowest bus frequency can be as low as
48000000 / (4 * 4095) = 2930Hz. Such an extremely low frequency will cause
the mmc framework take seconds to finish the initialization.
Limiting the minimum bus frequency to a slightly higher value can solve the
issue without any side effects.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
clean up octeontx_smi_probe by using the live-tree API.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Commit 4f0278dac5 ("net: sun8i-emac: Lower MDIO frequency") leads to
network failure on the OrangePi PC.
=> dhcp
sun8i_emac_eth_start: Timeout
According to the commit message the change of the MDIO frequency is only
required for external PHYs.
Fixes: 4f0278dac5 ("net: sun8i-emac: Lower MDIO frequency")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add SynQuacer's NETSEC GbE controller driver.
Since this driver will load the firmware from SPI NOR flash,
this depends on CONFIG_SYNQUACER_SPI=y.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Revert some changes of commit 3a97da12ee ("net: dwc_eth_qos: add dwc
eqos for imx support") that were probably added by mistake.
One of these changes can lead to received data corruption (enabling
FUP and FEP bits). Another causes invalid register rxq_ctrl0 settings
for some platforms. And another makes some writes at unknown memory
location.
Fixes: 3a97da12ee ("net: dwc_eth_qos: add dwc eqos for imx support")
Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
Cc: Ye Li <ye.li@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Disabling clk_ck clock leads to link up status loss in phy, which
leads to auto-negotiation restart before each network command
execution.
This issue is especially big for PXE boot protocol because of
auto-negotiation restarts before each configuration filename trial.
To avoid this issue don't disable clk_ck clock after it was enabled.
Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
commit f1bcad22dd ("net: e1000: add support for writing to EEPROM")
adds support for storing hwaddr in EEPROM however i210 devices do not
support this and thus results in errors such as:
Warning: e1000#0 failed to set MAC address'
Check if a flash device is present and if not return -ENOSYS indicating
this is not supported.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Remove the tab in clk_get_bulk to respect the coding rules.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add error callback in dfu stack to manage some board specific
behavior on DFU targets.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
For NOR devices the logical DFU buffer size is the sector_size,
as it is done in dfu_sf.c or in spi/sf_mtd.c
(sf_mtd_info.erasesize = flash->sector_size)
For NAND the DFU size was already limited to erasesize as
has_pages = true.
So the mtd dfu backend can use this erasesize for all the MTD devices,
NOR and NAND with dfu->max_buf_size = mtd->erasesize
This difference was initially copied from MTD command, where
data is fully available in RAM without size limitation.
This patch avoids to have many sector write in dfu_mtd.c at the end
of the DFU transfer and avoids issues with USB timeout or WATCHDOG.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
TCF flag only means that all data was sent to FIFO. To check if the
data was sent out of FIFO we should also wait for the BUSY flag to be
cleared. Otherwise there is a race condition which can lead to
inability to write short (one byte long) data.
Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This driver supports Rockchip NFC (NAND Flash Controller) found on
RK3308, RK2928, RKPX30, RV1108 and other SOCs. The driver has been
tested using 8-bit NAND interface on the ARM based RK3308 platform.
Support Rockchip SoCs and NFC versions:
- PX30 and RK3326(NFCv900).
ECC: 16/40/60/70 bits/1KB.
CLOCK: ahb and nfc.
- RK3308 and RV1108(NFCv800).
ECC: 16 bits/1KB.
CLOCK: ahb and nfc.
- RK3036 and RK3128(NFCv622).
ECC: 16/24/40/60 bits/1KB.
CLOCK: ahb and nfc.
- RK3066, RK3188 and RK2928(NFCv600).
ECC: 16/24/40/60 bits/1KB.
CLOCK: ahb.
Supported features:
- Read full page data by DMA.
- Support HW ECC(one step is 1KB).
- Support 2 - 32K page size.
- Support 8 CS(depend on SoCs)
Limitations:
- No support for the ecc step size is 512.
- Untested on some SoCs.
- No support for subpages.
- No support for the builtin randomizer.
- The original bad block mask is not supported. It is recommended to
use the BBT(bad block table).
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Replace msleep occurences by udelay.
drivers/pci/pcie_dw_rockchip.c:254:3: warning: implicit
declaration of function 'msleep' [-Wimplicit-function-declaration]
Cc: Patrick Wildt <patrick@blueri.se>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use the generic error number instead of specific error number.
Changes fix the below error.
drivers/pci/pcie_dw_rockchip.c: In function 'rk_pcie_read':
drivers/pci/pcie_dw_rockchip.c:70:10: error: 'PCIBIOS_UNSUPPORTED'
undeclared (first use in this function)
70 | return PCIBIOS_UNSUPPORTED;
| ^~~~~~~~~~~~~~~~~~~
drivers/pci/pcie_dw_rockchip.c: In function 'rk_pcie_write':
drivers/pci/pcie_dw_rockchip.c:90:10: error: 'PCIBIOS_UNSUPPORTED'
undeclared (first use in this function)
90 | return PCIBIOS_UNSUPPORTED;
| ^~~~~~~~~~~~~~~~~~~
Cc: Patrick Wildt <patrick@blueri.se>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the driver for rk3568 u-boot to get sdram capacity.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmDLD78cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyLhSB/0UqOd+Ujf2meiHU9yr
oOOCLxVTjTUfIZKLad/zwlj2Xqzsjs6XMawC95BgouvkQLmj/gwerRWcZPg9l7/X
hvb9VJi+iJoLRRpBPbeF3bMb92kCE+YZodFXyutlcY+Z0ZB9755zoVgR6ccKfksd
Xp2y8AFptfYQNZ1l0yb3lhm1261CldWALrGTjRpY2hQ8nEMbV8z6WUB1hAF9CECa
PGbKaiqm9OdktwHsLy4cYFFCuzkykn6T3P6ODineP7IxgEgZKTfJClSTFGY9S0GQ
kwd7K/7j0W3rI5NPknB+Fb4IFAaTs/oozR+5ml7j+2S3G5GXjSGx8zaSOmOZvpP3
KxwN
=/I5V
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for the 2021.10 cycle:
This feature set converts the boards pm9261 and pm9263 Ethernet support
to DM; enables hash command for all SAM boards; fixes the NAND pmecc
bit-flips correction; adds Falcon boot for sama5d3_xplained board; and
other minor adjustments.
Current tsec adapter sets adapter gigabit capabilities by default, and in
reality this must not always be the case.
It is possible that tsec adapter is used for 100Mbps connection, and in
this case setting 1000Mbps capabilities can lead to some side effects such
longer autoneg process.
In our ls102x designs this problem leads to long autoneg times (> 4 sec)
in case board rgmii link is 100Mbps capable only.
Limiting the rgmii link capabilities provides faster and smoother
link establishment.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
For eSDHC, power supply is through peripheral circuit.
Some eSDHC versions have value 0 of the bit but that
does not reflect the truth. 3.3V is common for SD/MMC,
and is supported for all boards with eSDHC in current
u-boot. So, make 3.3V is supported in default in code.
CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT can be enabled if
future board does not support 3.3V.
This is also a fix-up for one previous patch, which converted
to use IS_ENABLED() for CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
that is not a Kconfig option.
Fixes: 52faec3182 ("mmc: fsl_esdhc: replace most #ifdefs by IS_ENABLED()")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Stop to initialize the PCIe controller if it's disabled by RCW.
Fixes: 118e58e26e ("pci: layerscape: Split the EP and RC driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Read Linux PPFE firmware from flash partition and pass it to Linux through
FDT entry. So that we can avoid placing PPFE firmware in Linux rootfs.
(FDT may increase at max by 64KB)
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that we have only one clock driver, we don't need to have our own
subdirectory. Move the driver back with the rest of the clock drivers.
The MAINTAINERS for kendryte pinctrl is also fixed since it has always been
wrong.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This driver no longer serves a purpose now that we have moved away from
CCF. Drop it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This speeds up boot by preventing multiple reconfigurations of the PLLs.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This adds support for setting clock rates, which was left out of the
initial CCF expunging. There are several tricky bits here, mostly related
to the PLLS:
* The PLL's bypass is broken. If the PLL is reconfigured, any child clocks
will be stopped.
* PLL0 is the parent of ACLK which is the CPU and SRAM's clock. To prevent
stopping the CPU while we configure PLL0's rate, ACLK is reparented
to IN0 while PLL0 is disabled.
* PLL1 is the parent of the AISRAM clock. This clock cannot be reparented,
so we instead just disallow changing PLL1's rate after relocation (when
we are using the AISRAM).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Since we are no longer using CCF we cannot use the default soc_clk_dump.
Instead, implement our own.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Now that there no separate PLL driver, we can no longer make the PLL
functions static. By moving the PLL driver in with the rest of the clock
code, we can make these functions static again. We still keep the pll
header for unit testing, but it is pretty reduced.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This is effectively a complete rewrite to remove all dependency on CCF.
The code is now smaller, and so is the binary. It also takes up less memory
at runtime (since we don't have to create 40 udevices). In general, I am
much happier with this driver as much of the complexity and late binding
has been removed.
The k210_*_params structs which were previously used to initialize CCF
clocks are now used as the complete configuration. Since we can write our
own division logic, we can now do away with several "half" clocks which
only existed to provide constant factors of two.
The clock IDs have been renumbered to remove unused clocks. This may not be
the last time they are renumbered, since we have diverged with Linux. There
are also still a few clocks left out which may need to be added back in.
In general, I have tried to leave out behavioral changes. However, there is
a small bugfix regarding ACLK. According to the technical reference manual,
its mux comes *after* its divider (which is present only for PLL0). This
would have required yet another intermediate clock to fix with CCF, but
with the new driver it is just 2 lines of code :)
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Since 291da96b8e ("clk: Allow clock defaults to be set during re-reloc
state for SPL only") it has been impossible to set clock defaults before
relocation. This is annoying on boards without SPL, since there is no way
to set clock defaults before U-Boot proper. In particular, the aisram rate
must be changed before relocation on the K210, since U-Boot will hang if we
try and change the rate while we are using aisram.
To get around this, extend the stage parameter to allow force setting
defaults, even if they would be otherwise postponed for later. A device
tree property was decided against because of the concerns in the original
commit thread about the overhead of repeatedly parsing the device tree.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.
Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.
Tested-by: Anji Jagarlmudi <anji.jagarlmudi@nxp.com>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[Fixed checkpatch space error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
In absence of Device Manager (DM) services such as at R5 SPL stage,
driver will have to natively setup TCHAN/RCHAN/RFLOW cfg registers.
Add support for the same.
Note that we still need to send chan/flow cfg message to TIFS via TISCI
client driver in order to open up firewalls around chan/flow but setting
up of cfg registers is handled locally.
U-Boot specific code is in a separate file included in main driver so
as to maintain similarity with kernel driver in order to ease porting of
code in future.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210607141753.28796-8-vigneshr@ti.com
In absence of Device Manager (DM) services such as at R5 SPL stage,
driver will have to natively setup Ring Cfg registers. Add support for
the same.
Note that we still need to send RING_CFG message to TIFS via TISCI
client driver in order to open up firewalls around Rings.
U-Boot specific code is in a separate file included in main driver so
as to maintain similarity with kernel driver in order to ease porting of
code in future.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210607141753.28796-7-vigneshr@ti.com
On J721e and J7200, MCU R5 core (boot master) itself would run Device
Manager (DM) Firmware and interact with TI Foundational Security (TIFS)
firmware to enable DMA and such other Resource Management (RM) services.
So, during R5 SPL stage there is no such RM service available and ti_sci
driver will have to directly interact with TIFS using DM to DMSC
channels to request RM resources.
Therefore add DT binding and driver for the same. This driver will
handle Resource Management services at R5 SPL stage.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210607141753.28796-4-vigneshr@ti.com
In case of R5 SPL, GET_RANGE API service is not available (as DM
services are not yet up), therefore service such calls locally using
per SoC static data.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210607141753.28796-3-vigneshr@ti.com
R5 SPL would need to talk to DMSC using DM to DMSC sec-proxy threads.
Mark these as valid threads in the driver.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210607141753.28796-2-vigneshr@ti.com
Add support command for debugging K3 power domains. This is useful with
the HSM rearch setup, where power domains are directly controlled by SPL
instead of going through the TI SCI layer. The debugging support is only
available in the u-boot codebase though, so the raw register access
power domain layer must be enabled on u-boot side for this to work. By
default, u-boot side uses the TI SCI layer, and R5 SPL only uses the
direct access methods.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Normally, power domains are handled via TI-SCI in K3 SoCs. However,
SPL is not going to have access to sysfw resources, so it must control
them directly. Add driver for supporting this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add driver to support TI K3 generation SoC clocks. This driver registers
the clocks provided via platform data, and adds support for controlling
the clocks via DT handles.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Add support for TI K3 SoC PLLs. This clock type supports
enabling/disabling/setting and querying the clock rate for the PLL. The
euclidean library routine is used to calculate divider/multiplier rates
for the PLLs.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Clock rates are cached within the individual clock nodes, and right now
if one changes a clock rate somewhere in the middle of the tree, none
of its child clocks notice the change. To fix this, clear up all the
cached rates for us and our child clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
If a clock provider is not ready for assigning default rates/parents
during its probe, it may return -EPROBE_DEFER directly from xlate.
Handle this special case properly by skipping the entry and adjusting the
return value to pass. The defaults will be handled properly in post probe
phase then.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Set rate should return the new clock rate on success, and negative error
value on failure. Fix this, as currently set_rate returns 0 on success.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Bail out early if device returned for the parent clock is null.
This avoids warning prints like this when doing clk dump:
dev_get_uclass_priv: null device
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Current driver only supports registering fixed rate clocks from DT. Add
new API which makes it possible to register fixed rate clocks directly
from e.g. platform specific clock drivers.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
With the sysfw rearch, sysfw PM calls are no longer available from SPL
level. To properly support this, remove the is_on checks and the reset
assertion from the R5 remoteproc driver as these are not supported.
Attempting to access unavailable services will cause the device to hang.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Enable manual start in zynqmp_qspi_fill_gen_fifo().
Also enable GQSPI_IXR_GFNFULL_MASK and check for it instead of
GQSPI_IXR_GFEMTY_MASK.
Add dummy write to genfifo register in chipselect.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
On reset, the RTC loads the 2000-01-01 date with a wrong day of the
week (Sunday instead of Saturday).
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-9-dariobin@libero.it
Update the driver to support the device tree and the driver model.
The read / write helpers in rtc_ops allow access to scratch registers
only. The offset parameter is added to the address of the scratch0
register.
Support for non-DM has been removed as there were no users.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-8-dariobin@libero.it
The RTC module contains a kicker mechanism to prevent any spurious
writes from changing the register values. To set the time, you must
first unlock the TC registers, update them and then lock.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-6-dariobin@libero.it
To write correct data to the TC registers, the STATUS register must be
read until the BUSY bit is equal to zero. Once the BUSY flag is zero,
there is a 15 μs access period in which the TC registers can be
programmed.
The rtc_wait_not_busy() has been inspired by the Kernel.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-5-dariobin@libero.it
Use 32-bit access only where it is needed. Most of the RTC registers
contain useful information in the 8 least significant bits, the others
are reserved.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-4-dariobin@libero.it
The Davinci's onchip RTC is also present on TI OMAP1, AM33XX, AM43XX and
DRA7XX SOCs. So, let's enable compilation for these architectures too.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-2-dariobin@libero.it
Usb needs IMXRT1050_CLK_USBOH3 clock to be enabled, so let's add it to
clock driver.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Lcd peripheral needs 2 different gates to be enable to work, so let's
introduce the missing one(LCDIF_PIX) and rename the existing one
(LCDIF_APB).
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Some SoC needs "disp_axi" clock to be enabled, so let's try to retrieve it
and enabling. If it fails it gives only a debug(), but this clock as well
as "axi" clock is not mandatory.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
On some SoC mxsfb needs more than one clock gate(actual "per" clock). So
let's introduce "axi" clock that can be provided but it's not mandatory.
This is inspired from linux mxsfb driver. Also let's rename "per" clock to
"pix" clock for compatibility with already existing .dts lcdif nodes
implementation.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
This timer driver uses GPT Timer (General Purpose Timer) available on
a lot of i.MX SoCs family. This driver deals with both 24Mhz oscillator
as well as peripheral clock.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
[Giulio: added the driver's stub and handled peripheral clock prescaler
setting making driver to work correctly]
Signed-off-by: Jesse Taube <mr.bossman075@gmail.com>
[Jesse: added init, setting prescaler for 24Mhz support and enabling
timer]
When `usb start` is called on the terminal, the dwc2 driver will try
to start every USB device as host first, even if it is explicitly
configured as peripheral in the device tree (dr_mode = "peripheral").
So to avoid an unwanted 15 seconds delay when initializing the usb
(one second per channel = 1s x 15), this patch adds a check to the
initialization, and will skip host initialization of the device is
explicitly set as peripheral. The checking is already done similarly
in the `drivers/usb/gadget/dwc2_udc_otg.c` driver.
Signed-off-by: João Loureiro <joaofl@gmail.com>
Currently the config options CONFIG_SYS_DFU_DATA_BUF_SIZE and
CONFIG_SYS_DFU_MAX_FILE_SIZE are being set in include/configs/<board>.h
files and also in <board_name>_defconfig files without a Kconfig option. It
is easier for users to set these configs in defconfig files than in config
header files as they are a part of the source code.
Add Kconfig symbols, and update the defconfigs by using tools/moveconfig.py
script.
Suggested-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Kernel device tree got updated to use clock name as "ref" instead of
"usb2_refclk". Fix cdns3-ti.c to use the correct name.
Fixes: 70e167495a ("arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot")
Fixes: 6239cc8c4e ("arm: dts: k3-j7200: Sync Linux v5.11-rc6 dts into U-Boot")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Synchronize R-Car Gen2/Gen3 pinctrl tables with Linux 5.12,
commit 9f4ad9e425a1 ("Linux 5.12") . This is a rather large
commit, since the macros in sh-pfc.h also got updated, so
all the PFC tables must be updated in lockstep.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Not correcting anything in case of empty ECC data area
is not an appropriate strategy, because an uncorrected bit-flip
in an empty sector may cause upper layers (namely UBI) fail to work
properly. Therefore the approach chosen in Linux kernel and other
u-boot mtd drivers has been adopted, where a heuristic implemented
by nand_check_erased_ecc_chunk() is used in order to detect and
correct empty sectors.
Tested with sama5d3_xplained and sam9x60-ek.
Signed-off-by: Kai Stuhlemmer (ebee Engineering) <kai.stuhlemmer@ebee.de>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
[ta: reorder if conditions, change commit subject, s/uint8_t/u8.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Removed call of ofnode_translate_address() after ofnode_read_resource
in luton_switch.c:luton_probe(); it is unnecessary since
the commit feb7ac457c ("dm: core: Add address translation in
fdt_get_resource").
Fixes: feb7ac457c ("dm: core: Add address translation in fdt_get_resource")
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reported-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
With commit 41575d8e4c ("dm: treewide: Rename auto_alloc_size members
to be shorter") "priv_auto_alloc_size" was renamed to "priv_auto". This
driver was sent to the mailing list before that change, merged after it,
and still has the old form. Apply the rename here as well.
Fixes: 1b9ee2882e ("pwm: Add a driver for Chrome OS EC PWM")
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In of_get_address(), there is:
dev_count_cells(dev, &na, &ns);
followed by:
bus->count_cells(dev, &na, &ns);
but no codes in between use na/ns, hence the first call is useless.
By dropping the first call, dev_count_cells() is now useless too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
'dma-ranges' frequently exists without parent nodes having 'dma-ranges'.
While this is an error for 'ranges', this is fine because DMA capable
devices always have a translatable DMA address. Also, with no
'dma-ranges' at all, the assumption is that DMA addresses are 1:1 with
no restrictions unless perhaps the device itself has implicit
restrictions.
This keeps in sync with Linux kernel commit:
81db12ee15cb: of/address: Translate 'dma-ranges' for parent nodes missing 'dma-ranges'
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The `ranges` DT property of the PCIe node is currently ignored by
Aardvark driver - all entries are used as transparent PCIe MEM, despite
some of them being defined for IO in DT.
This is because the driver does not setup PCIe outbound windows and thus
a default configuration is used.
This can cause an external abort on CPU when a device driver tries to
access non-MEM space.
Setup the PCIe windows according to the `ranges` property for all
non-MEM resources (currently only IO) and also non-transparent MEM
resources.
Because Linux expects that bootloader does not setup Aardvark PCIe
windows, disable them before booting Linux.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Change DT compatible string for A3700 PCIe from 'marvell,armada-37xx-pcie'
to 'marvell,armada-3700-pcie' to make U-Boot A3700 PCIe DT node compatible
with Linux' DT node.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Disable Root Bridge I/O space, memory space and bus mastering in Aardvark's
remove method, which is called before booting Linux kernel.
This ensures that PCIe device which was initialized and used by U-Boot
cannot do new DMA transfers until Linux initializes PCI subsystem and loads
appropriate drivers for the device.
During initialization of PCI subsystem Linux in fact disables this bus
mastering on Root Bridge (and later enables it when driver is loaded and
configured), but there is a possibility of a small window after U-Boot
boots Linux when bus mastering is enabled, which is not correct.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
During our debugging of the Aardvark driver in Linux we have discovered
that the PCIE_CORE_LINK_CTRL_STAT_REG register in fact controls standard
PCIe Link Control Register for PCIe Root Bridge. This led us to discover
that the name of the PCIE_CORE_LINK_TRAINING macro and the corresponding
comment by this macro's usage is misleading; this bit in fact controls
Retrain Link, which, according to PCIe base spec is defined as:
A write of 1b to this bit initiates Link retraining by directing the
Physical Layer LTSSM to the Recovery state. If the LTSSM is already in
Recovery or Configuration, re-entering Recovery is permitted but not
required.
Entering Recovery state is normally done from LTSSM L0, L0s and L1 states.
But since the pci-aardvark.c driver enables Link Training just a few lines
above, the controller is not in L0 ready state yet. So setting aardvark bit
PCIE_CORE_LINK_TRAINING does not actually enter Recovery state at this
place.
Moreover, trying to enter LTSSM Recovery state without other configuration
is causing issues for some cards (e.g. Atheros AR9xxx and QCA9xxx). Since
Recovery state is not entered, these issues are not triggered.
Remove code which tries to enter LTSSM Recovery state completely.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix compilation error when Werror is turned on. The warning could
possible break some CI builds.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Add pcie driver for SiFive fu740, the driver depends on
fu740 gpio, clk and reset driver to do init. Force running at Gen1
for better capatible enumeration.
Several devices are tested:
a) M.2 NVMe SSD
b) USB-to-PCI adapter
c) Ethernet adapter (E1000 compatible)
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
BITS_PER_LONG is used to represent register's size which is 32.
But when compiled on arch64, BITS_PER_LONG is then equal to 64.
Fix bank and offset computation to make it work on arch32 and
arch64 and ensure that register's size is always equal to 32.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Fix the result of DFU_OP_WRITE operation in mtd_block_op function
when mtd_lock is not supported (-EOPNOTSUPP) to avoid DFU stack
error on the DFU manifestation of the MTD device, when
dfu_flush_medium_mtd is called.
Without this patch, dfu-util failed on dfuERROR state at the end
of the write operation on the alternate even if MTD write
opeartion is correctly performed.
$> dfu-util -a 3 -D test.bin
....
DFU mode device DFU version 0110
Device returned transfer size 4096
Copying data from PC to DFU device
....
Download [=========================] 100% 225469 bytes
Download done.
state(10) = dfuERROR, status(14) = Something went wrong,
but the device does not know what it was Done!
Fixes: 65f3fc18fc ("dfu_mtd: Add provision to unlock mtd device")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Sughosh Ganu <sughosh.ganu@linaro.org>
The ti_sci_msg_req_reboot message payload has been extended to include a
domain field, but for the purposes of u-boot this should be zero to
reset the entire SoC as it did before. Include domain for completeness
and set to zero to ensure proper operation.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
If reg property of pinctrl-single node requires address translation then
probe fails with following message:
single-pinctrl pinctrl@4301c000: failed to get base register size
This is because driver uses dev_read_addr_size() to get size which also
tries to fetch untranslated addr and fails.
Fix this by using dev_read_addr_size_index() which takes care of address
translation and also makes following dev_read_addr() call redundant.
This fixes Ethernet failures on TI's AM654 based EVMs due to lack of
pinmux configuration.
Fixes: 9fd8a430f3 ("pinctrl: single: get register area size by device API")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
With the last user of this driver removed, remove the driver.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When building highbank_defconfig with LTO, the compiler complains about
type mismatch of function ahci_link_up().
The third parameter of this function is of type u8 in
drivers/ata/ahci.c, but of type int in board/highbank/ahci.c.
There is no reason in using u8, and the code using this function
actually passes an int variable into the function (so it is implicitly
converted to u8).
Change the type of this parameter to int in drivers/ata/ahci.c.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When apf27_defconfig is built with LTO, linking complains about
undefined reference to `nand_boot`. This is because it is referenced
from inline assembly. Make it visible.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
This commit does the same thing as Linux commit 33def8498fdd.
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is a serious bug in regmap_read() and regmap_write() functions
where an uint pointer is cast to (void *) which is then cast to (u8 *),
(u16 *), (u32 *) or (u64 *), depending on register width of the map.
For example given a regmap with 16-bit register width the code
int val = 0x12340000;
regmap_read(map, 0, &val);
only changes the lower 16 bits of val on little-endian machines.
The upper 16 bits will remain 0x1234.
Nobody noticed this probably because this bug can be triggered with
regmap_write() only on big-endian architectures (which are not used by
many people anymore), and on little endian this bug has consequences
only if register width is 8 or 16 bits and also the memory place to
which regmap_read() should store it's result has non-zero upper bits,
which it seems doesn't happen anywhere in U-Boot normally. CI managed to
trigger this bug in unit test of dm_test_devm_regmap_field when compiled
for sandbox_defconfig using LTO.
Fix this by utilizing an union { u8; u16; u32; u64; } and reading data
into this union / writing data from this union.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
The V3U SoC has several unlock registers, one per register group. They
reside at offset zero in each 0x200 bytes-sized block.
To avoid adding yet another table to the PFC implementation, this
patch adds the option to specify an address mask instead of the fixed
address in sh_pfc_soc_info::unlock_reg.
This is a direct port of Linux 5.12 commit e127ef2ed0a6
("pinctrl: renesas: Implement unlock register masks") by
Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The help text for Gen2 entries had a copy paste error, still containing
the Gen3 string, while the description was correctly listing Gen2. Fix
the help text.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
