The Colibri PXA270 has been end-of-life since quite a while and would
require more and more maintenance (e.g. DM conversions).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop optional support for the ancient Apalis iMX6 V1.0 hardware which
had the UART wired as DCE rather than DTE.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This fixes the following crash when run on a Colibri iMX7S aka solo:
Colibri iMX7 # usb start
starting USB...
Bus usb@30b10000: USB EHCI 1.00
Bus usb@30b20000:
The i.MX 7Solo has only one single USB OTG1 but no USB host port. Trying
to initialize the nonexisting port just crashes.
While at it also drop board_usb_phy_mode() which is also no longer used
in the driver model age.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The power/bd71837.h should no longer be included, since V1.1 SoM
uses only the PCA9450 PMIC and the BD71837 support was removed.
Drop the header too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now that it is possible to use regulator-fixed-clock make use
of it. This makes U-Boot detect the PHY on first cold-boot.
This commit also adjusts the code in setup_fec and follows
how it is done in mx6ullevk.c
This commit also slows down the boot-process by about 150ms
as it now waits for the regulator-fixed-clock voltage that
drives the PHY to go up.
If you rely on very fast boot-speeds and don't need ethernet
for your boot-process you can safely revert the changes on
imx6ull-colibri.dtsi
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Toradex uses the variable variant to distinguish between modules with
eMMC, NAND with wifi and NAND without wifi.
This variable is set on every boot. Set this variable also if we have a
NAND module without wifi to prevent issues.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
U-Boot should never save the environment unasked.
This also avoids storing broken fdt_module to flash.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
U-Boot should never save the environment unasked.
This also avoids storing broken ftd_file to eMMC.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Rename board_early_init_f() to board_early_init(), since this function
has nothing to do with actual board_early_init_f() as used throughout
U-Boot. The board_early_init() is function local to this board used to
configure UART and WDT pinmux. Wrap init_uart_clk() into this function
so that early UART init would be all in one place. Turn the function
into __weak one, so it could be overridden in case custom carrier board
uses different UART or needs custom IOMUX settings.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is supposed to be a build-system flag. Move it there so we can
define it before linux/kconfig.h is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add code to build the eMMC variant of the Colibri iMX6ULL, i.e. the
'Colibri iMX6ULL 1GB' which has a eMMC instead of the raw NAND used
on other SKUs.
Related-to: ELB-4056, ELB-4057
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Integrate new Toradex SKU 0062 Colibri iMX6ULL 1GB IT. This commit
basically adjusts three parameters of the RAM settings:
Increase density from 4Gb to 8Gb
Increase ROW address from 15 to 16
Increase tRFC (refresh command time) from 260 to 350
This timing is valid for all Toradex Colibri iMX6ULL SKUs
Related-to: ELB-4055, ELB-4057
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add new i.MX 6ULL and 8M Plus SKUs to ConfigBlock handling:
0062: Colibri iMX6ULL 1GB IT (eMMC)
0063: Verdin iMX8M Plus Quad 4GB IT
0064: Verdin iMX8M Plus Quad 2GB Wi-Fi / BT IT
0065: Verdin iMX8M Plus QuadLite 1GB IT
0066: Verdin iMX8M Plus Quad 8GB Wi-Fi / BT
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Restore "Is the module an IT version? [y/N]" for "cfgblock create"
interactive mode command, which was leading to invalid detection
of 0051 Colibri iMX8DX 1GB WB module;
Fixes: a5b5ad4d85 ("toradex: tdx-cfg-clock: add new i.mx 8m mini/plus skus")
Related-to: ELB-3482
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Also take over maintainership of remaining Toradex SoMs as Oleksandr
has left our company.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
CC: Oleksandr Suvorov <cryosay@gmail.com>
NXP used to setup the gpmi clock root from gpmi_clk in early versions
in their downstream BSP. [1]
However on mainline the gpmi clock root was always setup from enfc
since the beginning of the i.MX 6 series SoCs, which is still the same
today. [2]
NXP followed the mainline approach at some point and changed
setup_gpmi_io_clk to setup gpmi clock root from enfc which left faulty
code behind in our board file. [3]
This commit follows the change of NXP as it improves the performance of
the NAND from ~1.2 MiB/s to ~12 MiB/s. [3]
This change was verified to work in recovery-mode and u-boot loaded
from NAND on all four Colibri iMX6ULL SKUs from Toradex.
The frequency used to read the NAND, measured on RE# (Read Enable):
before this patch: 1.4 MHz
after this patch: 22 MHz
in Linux Kernel: 50 MHz
[1] https://source.codeaurora.org/external/imx/uboot-imx/tree/arch/arm/cpu/armv7/mx6/clock.c?h=nxp/imx_v2016.03_4.1.15_2.0.0_ga#n62
[2] commit 23608e23fd ("i.mx: add the initial support for freescale i.MX6Q processor")
[3] https://source.codeaurora.org/external/imx/uboot-imx/commit/?id=7a82a19ceabfb04bbc1591a67c99751748781c7d
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
We drop support for Verdin iMX8M Mini V1.0B.
Related-to: ELB-3551
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Turns out Microship (formerly Micrel) meanwhile integrated proper
support for the DLL setup on their KSZ9131. Unfortunately, this
conflicts with our previous board code doing that.
Fix this by getting rid of our board code and just relying on the
generic implementation relying on rgmii-id being used as phy-mode.
Fixes: commit c6df0e2ffd
("net: phy: micrel: add support for DLL setup on ksz9131")
Fixes: commit af2d3c91d8
("ARM: dts: imx8mm-verdin: Set PHY mode to RGMII-ID")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable dynamic DDR calibration to have a reliable behavior on edge
temperatures conditions.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Enable dynamic DDR calibration to have a reliable behavior on edge
temperatures conditions.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
As this is only useful when booting with ATAGs, which are now largely
disabled, remove this value for the remaining platforms. We have a few
places in the code that had been testing for MACH_TYPE as a sort of
internal logic. Update those to use different but still correct CONFIG
symbols.
Cc: Phil Sutter <phil@nwl.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Provide a default Kconfig value of the default script
- Largely continue to define this via the board Kconfig file
- For the boards that select a script based on defconfig rather than
TARGET, keep this within the defconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
The USB recovery mode is used by Toradex to load the Toradex Easy
Installer image which supports further system images installation.
Prepare for loading and launching the Toradex Easy Installer if the
USB Recovery mode is activated.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Only one dtb is currently supported, so match with imx6-colibri.
Signed-off-by: Ming Liu <ming.liu@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
If config block support is enabled, USB gadget modes unconditionally
use Toradex Product ID as USB PID. Some applications might prefer a
different and/or static USB PID. Add a Kconfig configuration option
to descide whether to use USB PID from config block or the fallback
config option CONFIG_G_DNL_PRODUCT_NUM.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
In case USB serial downloader has been used to load U-Boot start the
serial download protocol (SDP) emulation. This allows to download
complete images such as Toradex Easy Installer over USB SDP as well.
This code uses the boot ROM provided boot information to reliably
detect USB serial downloader.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
U-boot might display wrong module revision information
for modules with an assembly version 'K'. "cfgblock create"
does not takes into account all revision digits from PID8.
This fix takes into account all digits of PID8
to store module revision.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to. This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value. Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.
Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g. COLD vs WARM resets). As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).
To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely. Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.
This transformation was done with the following coccinelle patch:
@@
expression argvalue;
@@
- reset_cpu(argvalue)
+ reset_cpu()
@@
identifier argname;
type argtype;
@@
- reset_cpu(argtype argname)
+ reset_cpu(void)
{ ... }
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
In the spirit of using the same base name for all of these related macros,
rename this to have the operation at the end. This is not widely used so
the impact is fairly small.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current macro is a misnomer since it does not declare a device
directly. Instead, it declares driver_info record which U-Boot uses at
runtime to create a device.
The distinction seems somewhat minor most of the time, but is becomes
quite confusing when we actually want to declare a device, with
of-platdata. We are left trying to distinguish between a device which
isn't actually device, and a device that is (perhaps an 'instance'?)
It seems better to rename this macro to describe what it actually is. The
macros is not widely used, since boards should use devicetree to declare
devices.
Rename it to U_BOOT_DRVINFO(), which indicates clearly that this is
declaring a new driver_info record, not a device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Hand over maintainership of Toradex SoMs (that I was responsible of) to
Oleksandr because of my resignation from Toradex, as such I will
have no immediate involvement with these modules and as a result not
able to continue maintaining these boards.
CC: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
