The power management controller found on Apple SoCs als provides
a way to reset all devices within a power domain. This is needed
to cleanly shutdown the NVMe controller before we hand over
control to the OS.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This mailbox driver provides a communication channel with the
Apple IOP controllers found on Apple SoCs. These IOP controllers
are used to implement various functions such as the System
Manegement Controller (SMC) and NVMe storage. It allows sending
and receiving a 96-bit message over a single channel.
The header file with the struct used for mailbox messages is taken
straight from Linux.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
According to their TRMs, Cortex ARMv7 CPUs with SMP support require the
ACTLR.SMPEN bit to be set as early as possible, before any cache or TLB
maintenance operations are done. As we do those things still in start.S,
we need to move the SMPEN bit setting there, too.
This introduces a new ARMv7 wide symbol and code to set bit 6 in ACTLR
very early in start.S, and moves sunxi boards over to use that instead
of the custom code we had in our board.c file (where it was called
technically too late).
In practice we got away with this so far, because at this point all the
other cores were still in reset, so any broadcasting would have been
ignored anyway. But it is architecturally cleaner to do it early, and
we move a core specific piece of code out of board.c.
This also gets rid of the ARM_CORTEX_CPU_IS_UP kludge I introduced a few
years back, and moves the respective logic into the new Kconfig entry.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
=HtB+
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
This driver supports power domains for the power management
controller found on Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rely on the new watchdog timer driver and the sysreset uclass to
reset the system. This gets rid of hard-coded addresses and
should work on systems based on the new M1 Pro and M1 Max SoCs
as well.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-on: Apple M1 Macbook
Tested-by: Simon Glass <sjg@chromium.org>
ZynqMP modepin driver has capability to get/set/check status of modepin
gpios. These modepins are accessed using xilinx firmware. In modepin
register, [3:0] bits set direction, [7:4] bits read IO, [11:8] bits
set/clear IO.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/2d802d98fd56d95d764532a33e844d935e0cebb3.1635505900.git.michal.simek@xilinx.com
Use this new Kconfig instead of OF_BOARD, so we know for sure which boards
obtain their devicetree from a prior stage. Leave sandbox alone since it
does not. Also don't touch xilinx_versal_virt since it does not have a
specific TARGET Kconfig.
This option implies OF_BOARD for now, but with future work standard
passage may be used instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add rpi_4_32b and rpi_arm64 to the list of boards converted]
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver supports both pin muxing and GPIO support for the
pin control logic found on Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
-----BEGIN PGP SIGNATURE-----
iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmGL7ykcHHBhdHJpY2Uu
Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/pl1iD/45ARfQCdlq5Iq8VbAf
NV1TjRguoLU6zR5XhyGAIoDkg87Bsty2ayFyAfz8pHkpEQAFkj9bhiaRZEQj2SSi
avb2slYGC6iLBEgVBfHjnih4hf0JPTJWcCx+0IO298IknJ49qFfujBFdb3LCbXzt
zc6QE4mvWWdQHQfNym5UjHqJvI2seHbarEmltAQNn1hqYevFFQYH6vMtgYtZGH18
c63HeW6uDuGdxGJ9/dzuV/M5bZUAQOI2jJ9OFv7UYQyrzkvLd4M5Qeb52OZ7xNYZ
xNPCUtNnWUMUnGlpb/ANIUtqBYfcBj1iOMedchLtL9EANObFew/ktk0L1mdjLpQ4
neB8Im6KmcZkzPyNDs4ha8bSiwOGhrSMg+B49bpp01JvnmzMW3cFtexXL6nKAZyL
Iohv5MNp7Cf4Fn68v04RBzrAzcvBNPQUnN/19VMN+bqidAzN9y9N7Jc8JgVSOEWN
OU45X5N840CjqWr8xZ9znICqCdgnY4QtCI9zi6JLHuvWMG3+c10fzyozRfh/OWkE
3RSyjf9zSjlzYsOEIe8e5Kz/FqLhYqrhdJz2Aqoz5E3k7YQke8WU/OadOU7BWs5U
QoIMpq8jcAiNZqoMW/V5pxW2nqIB4VIX7LDYuT2TEnVt+hhLP59NtzFTMEjY68Rk
cH+alF5WHbnqIXgMh5BokUwgxA==
=lqEG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211110' of https://source.denx.de/u-boot/custodians/u-boot-stm
- DHSOM update:
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
The stm32 gpio driver private data are not needed in arch include files,
they are not used by code except for stm32 gpio and pincontrol drivers,
using the same IP; the defines for this IP is moved in a new file
"stm32_gpio_priv.h" in driver/gpio.
This patch avoids to have duplicated file gpio.h for each SOC
in MPU directory mach-stm32mp and in each MCU directory arch-stm32*
and allows to remove CONFIG_GPIO_EXTRA_HEADER for all STM32.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Instead of hardcoding the watchdog for reset, and the PMIC for poweroff,
use the sysreset framework to manage the available poweroff/reset
backends. This allows (as examples) using the PMIC to do a cold reset,
and using a GPIO to power off H3/H5 boards lacking a PMIC. Furthermore,
it removes the need to hardcode watchdog MMIO addresses, since the
sysreset backends can be discovered using the device tree.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The DART is an IOMMU that is used on Apple's M1 SoC. This driver
configures the DART such that it operates in bypass mode which is
enough to support DMA for the USB3 ports integrated on the SoC.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Apple M1 SoCs include an S5L UART which is a variant of the S5P
UART. Add support for this variant and enable it by default
on Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Apple's M1 SoC that is used in "Apple Silicon"
Macs. This builds a basic U-Boot that can be used as a payload
for the m1n1 boot loader being developed by the Asahi Linux
project.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Add MAINTAINERS entry]
Stop using the device tree as a source for ad-hoc information.
This reverts commit 2ae7adc659.
Signed-off-by: Michael Walle <michael@walle.cc>
[trini: Also make board/broadcom/bcmns3/ns3.c fail clearly now]
Signed-off-by: Tom Rini <trini@konsulko.com>
A watchdog helps recover from hangs or failure to boot an OS. It can
also be used by the sysreset framework to intentionally reset the
system. Now that a driver is available, let's enable this functionality
on sunxi boards.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
sunxi-common.h defines CONFIG_SPL_BSS_START_ADDR to put SPL's BSS in
DRAM. Due to this, we must select SPL_SEPARATE_BSS, or else SPL will
attempt to load its DTB from the wrong address (after BSS in DRAM).
This change fixes booting with SPL_OF_CONTROL=y.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
At some point back in 2018 prior_stage_fdt_address and OF_PRIOR_STAGE got
introduced, in order to support a DTB handed over by an earlier stage boo
loader. However we have another option in the Kconfig (OF_BOARD) which has
identical semantics.
So let's remove the option in an effort to simplify U-Boot's config and DTB
management, and use OF_BOARD instead.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that the last users of legacy I2C (outside of SPL) have been
resolved, we can enable DM_I2C at the sunxi architecture level.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last armada100 platform, remove that support
as well.
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last mx35 platform, remove that support as
well.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
vexpress_ca9x4 is seemingly the only board except for qemu_arm which
is able to run U-Boot correctly, using the `-M vexpress-a9` option to
QEMU. Building for qemu_arm and running qemu-system-arm with the `-M
virt` argument has a number of downsides, most importantly that it
only supports virtio storage drivers. This significantly reduces its
usefulness in testing memory card and Flash solutions, especially when
the tested images are from a third party source.
So therefore we reintroduce the vexpress_ca9x4 board in this commit,
with the explicit goal of using it with QEMU.
A number of differences to note from the original:
* Since the board was apparently unmaintained, I have now set myself
as the maintainer.
* The board has been converted to use the driver model, which was the
reason it was removed in the first place.
* The vexpress_ca15_tc2 and vexpress_ca5x2 boards, which were removed
in the same commit, are not necessary for the QEMU use case, and
have been omitted.
* An `mmc0` alias was introduced in the dts file. The mmc is not
detected correctly without this, now that it's based on the device
tree instead of the board's init function.
* A couple of other nodes were removed because they were problematic
when trying to run the UEFI bootmgr. Once again, the primary use
case here is QEMU, and these nodes are not needed for that to work.
* Unnecessary board init code has been removed, thanks to driver model
and device tree.
* `CONFIG_OF_EMBED` has been enabled. I know this goes against
recommended practice, but there doesn't seem to be any other way to
pass the dtb to U-Boot in the QEMU scenario. Using the -dtb argument
does not work, I suppose because U-Boot doesn't use the same
mechanics as the kernel when it's booting.
* Load addresses have been changed to fit QEMU use case.
People wanting to get a more detailed, yet somewhat isolated, diff
between this and the original, can run this command:
git diff c6c26a05b89f25a06e7562f8c2071b60fd0c9eac~1 -- \
$( git diff-tree --diff-filter=A -r --name-only HEAD~1 HEAD)
(Make sure to either check out this commit first, or replace HEAD with
the commit ID of this commit)
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
This patch enables the use of the optimized memset(), memmove() &
memcpy() versions recently added on ARM64.
Please note that these optimized functions are now only enabled for
recent GCC versions (>= 9.4), as earlier GCC versions throw these
errors:
aarch64-linux-ar: warning: arch/arm/lib/memset-arm64.o: unsupported GNU_PROPERTY_TYPE (5) type: 0xc0000000
...
Signed-off-by: Stefan Roese <sr@denx.de>
[trini: Make this default to off as it causes problems on some platforms still]
Signed-off-by: Tom Rini <trini@konsulko.com>
ARMv8.0 has optional crc32 instruction for crc32 calculation. The
instruction is mandatory since ARMv8.1. The crc32 calculation is
faster using the dedicated instruction, e.g. 1.4 GHz iMX8MN gives:
=> time crc32 0x50000000 0x2000000
time: 0.126 seconds # crc32 instruction
time: 0.213 seconds # software crc32
Add implementation using the compiler builtin wrapper for the crc32
instruction and enable it by default, since we don't support any
platforms which do not implement this instruction.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
[trini: Make crc32_table guarded by CONFIG_ARM64_CRC32]
Signed-off-by: Tom Rini <trini@konsulko.com>
With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
Per a request from Andre Przywara and agreed with by Peter Hoyes, the
vexpress aemv8r support wasn't quite ready to be merged, but the
discussion had moved off list. We should keep the first patch in the
series for now, but revert the rest. This reverts the following
commits:
e0bd6f31ce doc: Add documentation for the Arm vexpress board configs
30e5a449e8 arm: Use armv8_switch_to_el1 env to switch to EL1
b53bbca63b vexpress64: Add BASER_FVP vexpress board variant
2f5b7b7490 armv8: Add ARMv8 MPU configuration logic
37a757e227 armv8: Ensure EL1&0 VMSA is enabled
Signed-off-by: Tom Rini <trini@konsulko.com>
The BASER_FVP board variant is implemented on top of the BASE_FVP board
config (which, in turn, is based on the Juno Versatile Express board
config). They all share a similar memory map - for BASER_FVP the map is
inverted from the BASE_FVP
(https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map)
* Create new TARGET_VEXPRESS64_BASER_FVP target, which uses the same
board config as BASE_FVP and JUNO
* Adapt vexpress_aemv8a.h header file to support BASER_FVP (and rename
to vexpress_aemv8.h)
* Enable config to switch to EL1 for the BASER_FVP
* Create vexpress_aemv8r defconfig
* Provide an MPU memory map for the BASER_FVP
For now, only single core boot is supported.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[trini: Add MAINTAINERS, move BOOTCOMMAND to defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
A U-Boot image could be loaded and executed at a different
location than it was linked at.
For example, Aspeed takes a stable release version of U-Boot image
as the golden one for recovery purposes. When the primary storage
such as flash is corrupted, the golden image would be loaded to any
SRAM/DRAM address on demands through ethernet/UART/etc and run for
rescue.
To deal with this condition, the PIE is needed as there is only one
signed, golden image, which could be however executed at different
places.
This patch adds the PIE support for ARMv7 platform.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Enabling CONFIG_SYS_THUMB_BUILD produces a significantly smaller
U-Boot binary (250 KiB vs 320 KiB) that still seems to be fully
functional. Make use of that by default but keep it as "imply" so it
can be disabled for testing in case this causes trouble for someone.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Imply the options for new drivers added for ARM U8500 during the
U-Boot 2021.10 merge window. Adding these as "imply" in the Kconfig
avoids having to add them to all the board defconfigs but still allows
disabling them if wanted.
Also select DM_USB_GADGET if DM_USB is selected because otherwise
the Ux500 MUSB glue driver does not show up in the configuration.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
We move the SYS_CACHE_SHIFT_N options from arch/arm/Kconfig to
arch/Kconfig, and introduce SYS_CACHE_SHIFT_4 to provide a size of 16.
Introduce select statements for other architectures based on current
usage. For MIPS, we take the existing arch-specific symbol and migrate
to the generic symbol. This lets us remove a little bit of otherwise
unused code.
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Anup Patel <anup.patel@wdc.com>
Cc: Atish Patra <atish.patra@wdc.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Leo <ycliang@andestech.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Currently, there is no over-arching symbol for access to
arch/arm/mach-imx nor the CONFIG symbols that are common over all of
these related platforms. This new CONFIG symbol will allow us to start
down this path.
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the symbol that controls building some JEDEC SPD support functions
to Kconfig. This is required on the TI keystone 2 platforms and very
frequently (but not always) used on large number of Freescale/NXP
platforms, so use imply there.
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate CONFIG_GICV2 and CONFIG_GICV3 to Kconfig. We still have the GIC
related registers that need to be handled more cleanly but start by
moving this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
