Commit graph

2403 commits

Author SHA1 Message Date
Jagan Teki
bd363f80e4 imx6: geam6ul: Add FEC support
Add FEC support for Engicam GEAM6UL module.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 18:39:05 +01:00
Jagan Teki
dca7c2878a imx6: icorem6_rqs: Add I2C support
Add I2C support for Engicam i.CoreM6 RQS modules.

icorem6qdl-rqs> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
Bus 2:  i2c@021a8000
icorem6qdl-rqs> i2c dev 0
Setting bus to 0
icorem6qdl-rqs> i2c speed 100000
Setting bus speed to 100000 Hz
icorem6qdl-rqs> i2c probe
Valid chip addresses: 4F
icorem6qdl-rqs> i2c md 4F 0xff
00ff: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
icorem6qdl-rqs> i2c bus
Bus 0:  i2c@021a0000  (active 0)
   4f: generic_4f, offset len 1, flags 0
Bus 1:  i2c@021a4000
Bus 2:  i2c@021a8000

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 18:39:05 +01:00
Jagan Teki
871ec6da42 arm: imx6q: Add Engicam i.CoreM6 Quad/Dual RQS Starter Kit initial support
Boot from MMC:
-------------
U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44)
Trying to boot from MMC1

U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44 +0530)

CPU:   Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: POR
Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit
DRAM:  512 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
icorem6qdl-rqs>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 17:16:10 +01:00
Jagan Teki
d31373c4ac imx6: geam6ul: Add I2C support
Add I2C support for Engicam GEAM6UL module.

geam6ul> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
geam6ul> i2c dev 0
Setting bus to 0
geam6ul> i2c dev
Current bus is 0
geam6ul> i2c speed 100000
Setting bus speed to 100000 Hz
geam6ul> i2c probe
Valid chip addresses: 2C
geam6ul> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00    .......d........

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 17:16:10 +01:00
Jagan Teki
a5b9f8c8f0 arm: imx6ul: Add Engicam GEAM6UL Starter Kit initial support
Boot Log:
--------
U-Boot SPL 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30)
Trying to boot from MMC1

U-Boot 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30 +0530)

CPU:   Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 43C
Reset cause: POR
Model: Engicam GEAM6UL
DRAM:  128 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
geam6ul>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 17:16:10 +01:00
Jagan Teki
d90384e834 imx6: icorem6: Add I2C support
Add I2C support for Engicam i.CoreM6 qdl board.

icorem6qdl> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
Bus 2:  i2c@021a8000
icorem6qdl> i2c dev 2
Setting bus to 2
icorem6qdl> i2c speed 100000
Setting bus speed to 100000 Hz
icorem6qdl> i2c probe
Valid chip addresses: 2C
icorem6qdl> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00    .......d........

Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Heiko Schocher <hs@denx.de>
2016-12-16 17:15:27 +01:00
Jagan Teki
e920f60779 icorem6: Use CONFIG_DM_ETH support
Use CONFIG_DM_ETH and remove board_eth_init code
from board files.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 17:15:27 +01:00
Patrick Bruenn
98d62e618b arm: imx: add i.MX53 Beckhoff CX9020 Embedded PC
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.

The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc

Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
2016-12-16 12:57:12 +01:00
Peng Fan
47f73504d8 arm: imx: add i.MX6SLL EVK board support
Add i.MX6SLL EVK board support.
1. Add imx6sll-evk device tree.
2. Enable SDHC/I2C/UART.
3. Enable REGULATOR/PMIC/I2C/GPIO/SDHC/PINCTRL driver.

Boot Log:
U-Boot 2016.11-00127-gc635871-dirty (Nov 24 2016 - 13:28:19 +0800)

CPU:   Freescale i.MX6SLL rev1.0 at 792MHz
CPU:   Commercial temperature grade (0C to 95C)Reset cause: POR
Model: Freescale i.MX6SLL EVK Board
Board: MX6SLL EVK
DRAM:  2 GiB
i2c bus 0 at 35258368, no gpio pinctrl state.
PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-12-16 11:38:24 +01:00
Peng Fan
2cc021697b imx: mx6sll: add Kconfig entry for i.MX6SLL
add Kconfig entry for i.MX6SLL

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-12-16 11:38:24 +01:00
Peng Fan
dfca246f4c imx: mx6sll: add clock support
Add clock support for i.MX6SLL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-12-16 11:38:24 +01:00
Peng Fan
708f692753 imx: clock: gate clk before changing pix clk mux
The LCDIF Pixel clock mux is not glitchless, so need
to gate before changing mux.

Also change enable_lcdif_clock prototype with a new input
parameter to indicate disable or enable.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-12-16 11:38:24 +01:00
Peng Fan
e332623b03 imx: mx6sl: add lcdif clock support
Add lcdif clock support for i.MX6SL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-12-16 11:38:24 +01:00
Peng Fan
70ac169723 imx: mx6: lcdif: gate clock before changing mux
The mux for the lcd clock is not glitchless,
so need to first gate the clock before changing the mux.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-12-16 11:38:24 +01:00
Peng Fan
0e81982de0 imx: mx6: fix mmdc ch0 clk for 6SL
>From RM, per_periph2_clk_sel option3 is:
"derive clock from 198MHz clock (divided 392MHz PLL2 PFD)."

So fix it.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-12-16 11:38:24 +01:00
Marcin Niestroj
c9e40e65e1 board/liteboard: Add support for liteBoard
liteBoard is a development board which uses liteSOM as its base.

Hardware specification:
 * liteSOM (i.MX6UL, DRAM, eMMC)
 * Ethernet PHY (id 0)
 * USB host (usb_otg1)
 * MicroSD slot (uSDHC1)

Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
2016-12-16 10:31:13 +01:00
Breno Lima
0719b16f19 udoo_neo: Add thermal support
Add thermal support on the Kconfig file.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-12-16 10:21:25 +01:00
Breno Lima
4a056c4504 udoo_neo: Move MX6SX configuration to Kconfig
It's not necessary to define the processor in the defconfig file.

The preferred method to select the SoC is via Kconfig file.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-12-16 10:20:10 +01:00
Max Krummenacher
a02d517b01 arm: imx: initial support for colibri imx6
This adds board support for the Toradex module family Colibri iMX6.
The familiy consists of a module with i.MX6 DualLite, i.MX6 Solo, both
with a version for commercial and industrial temperature range.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2016-12-16 10:03:43 +01:00
Max Krummenacher
592f4aed6d arm: imx: initial support for apalis imx6
This adds board support for the Toradex module family Apalis iMX6.
The familiy consists of a module with i.MX6 Dual, i.MX6 Quad with
commercial and industrial temperature range.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2016-12-16 10:02:45 +01:00
Patrick Delaunay
91558c8153 arm: armv7: add us timer for bootstage
solve issue when bootstage is used with armV7 generic timer
first call of timer_get_boot_us() use the function get_timer()
before timer initialization (arch.timer_rate_hz = 0)
=> div by 0

Commit-notes

When I activate bootstage on ARMV7 architecture with platform
using the generic armv7 timer defined in file
./arch/arm/cpu/armv7m/timer.c

I have a issue because gd->arch.timer_rate_hz = 0

For me the get_timer() function should not used before timer_init
(which initialize gd->arch.timer_rate_hz) at least for the ARMV7
timer.

But in the init sequence, the first bootstage fucntion is called
before timer_init and this function use the timer function.

For me it is a error in the generic init sequence :
mark_bootstage is called before timer_init.

static init_fnc_t init_sequence_f[] = {
....
    arch_cpu_init_dm,
    mark_bootstage,        /* need timer, go after init dm */
...
#if defined(CONFIG_ARM) || defined(CONFIG_MIPS) || \
        defined(CONFIG_BLACKFIN) || defined(CONFIG_NDS32) || \
        defined(CONFIG_SPARC)
    timer_init,        /* initialize timer */
#endif
.......

To solve the issue for all the paltform, we can move timer_init()
call just before mark_bootstage() in this array...

It should be ok for ARMV7 but I don't sure for other platform
impacted
- the other ARM platform or ARMV7 wich don't use generic timer
- MIPS BLACKFIN NDS32 or SPARC

and I don't sure of impact for other function called
(board_early_init_f for example....)

=> This patch solve issue only in timer armv7
   get_boot_us() can be called everytime without div by 0 issue
   (gd->arch.timer_rate_hz is not used)

END

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
2016-12-09 08:39:10 -05:00
Tom Rini
194eded14c Merge git://git.denx.de/u-boot-mpc85xx 2016-12-04 13:55:15 -05:00
York Sun
72ccd31e64 armv7: ls1021a: Move SECURE_BOOT option to Kconfig
Move from CONFIG_SYS_EXTRA_OPTIONS to Kconfig option.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-12-02 12:38:41 -08:00
Tom Rini
4d6647ab17 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-11-30 09:57:52 -05:00
Lukasz Majewski
4db4d42ee2 imx6: clock: Enable External Memory Interface [EIM] clock (eim_slow_clock)
This patch extends the imx6 clock code to enable or disable the EIM
slow clock, which in necessary when one wants to use EIM interface t
o read/write from external memory (e.g. NOR).

Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
2016-11-30 09:57:19 +01:00
Christoph Fritz
730d25443a mx6sx: Add initial support for Samtec VIN|ING 2000 board
This patch adds initial support for Samtec VIN|ING 2000 board.

Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
2016-11-30 09:54:42 +01:00
Breno Lima
792f186846 mx6sx: Add initial support for UDOO Neo Board
UDOO Neo Board is a development board from Seco that has three models:
 - UDOO Neo Basic
 - UDOO Neo Basic Kick Starter
 - UDOO Neo Extended
 - UDOO Neo Full

All versions are based on the i.MX6 SoloX processor.

For more details about the UDOO Neo board, please refer to:
http://www.udoo.org/udoo-neo/

This work is based on a previous commit of Francesco Montefoschi
<francesco.monte@gmail.com>:
877b71184a

Only tested on the UDOO Neo Full board.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-11-29 16:48:20 +01:00
Eric Nelson
a425bf7281 ARM: mx6: ddr: use Kconfig for inclusion of DDR calibration routines
The DDR calibration routines are gated by conditionals for the
i.MX6DQ SOCs, but with the use of the sysinfo parameter, these
are usable on at least i.MX6SDL and i.MX6SL variants with DDR3.

Also, since only the Novena board currently uses the dynamic
DDR calibration routines, these routines waste space on other
boards using SPL.

Add a KConfig entry to allow boards to selectively include the
DDR calibration routines.

Signed-off-by: Eric Nelson <eric@nelint.com>
2016-11-29 16:40:37 +01:00
Eric Nelson
48c7d4379b mx6: ddr: add routine to return DDR calibration data
Add routine mmdc_read_calibration() to return the output of DDR
calibration. This can be used for debugging or to aid in construction
of static memory configuration.

This routine will be used in a subsequent patch set adding a virtual
"mx6memcal" board, but could also be useful when gathering statistics
during an initial production run.

Signed-off-by: Eric Nelson <eric@nelint.com>
2016-11-29 16:40:25 +01:00
Eric Nelson
7f17fb7400 mx6: ddr: pass mx6_ddr_sysinfo to calibration routines
The DDR calibration routines have scattered support for bus
widths other than 64-bits:

-- The mmdc_do_write_level_calibration() routine assumes the
presence of PHY1, and
-- The mmdc_do_dqs_calibration() routine tries to determine
whether one or two DDR PHYs are active by reading MDCTL.

Since a caller of these routines must have a valid struct mx6_ddr_sysinfo
for use in calling mx6_dram_cfg(), and the bus width is available in the
"dsize" field, use this structure to inform the calibration routines which
PHYs are active.

This allows the use of the DDR calibration routines on CPU variants
like i.MX6SL that only have a single MMDC port.

Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2016-11-29 16:40:12 +01:00
Eric Nelson
b33f74ead4 mx6: ddr: allow 32 cycles for DQS gating calibration
The DDR calibration code is only setting flag DG_CMP_CYC (DQS gating sample
cycle) for the first PHY.

Set the 32-cycle flag for both PHYs and clear when done so the MPDGCTRL0
output value isn't polluted with calibration artifacts.

Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2016-11-29 16:39:58 +01:00
Stefano Babic
2d221489df Merge branch 'master' of git://git.denx.de/u-boot
Signed-off-by: Stefano Babic <sbabic@denx.de>
2016-11-29 16:28:28 +01:00
Peng Fan
fea7452c15 armv7: psci: cpu_off: flush D-Cache before disable D-Cache
Before disable cache, need to first flush cache.

There maybe dirty data in D-Cache before disable D-Cache.
After disable D-Cache, the first store instructions in
psci_v7_flush_dcache_all will directly store registers
{r4-r5, r7, r9-r11, lr} to memory.
If there is dirty data before disable D-Cache,
psci_v7_flush_dcache_all will flush data to memory,
and may overwrite the memory that hold the registers
{r4-r5, r7, r9-r11, lr}.

So before disable cache, first flush D-Cache.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Hongbo Zhang <hongbo.zhang@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Tom Rini <trini@konsulko.com>
2016-11-29 08:15:31 -05:00
Tom Rini
983e37007d arm: Introduce arch/arm/mach-omap2 for OMAP2 derivative platforms
This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,omap5} in to arch/arm/mach-omap2
as subdirectories.  All refernces to the former locations are updated to
the current locations.  For the logic to decide what our outputs are,
consolidate the tests into a single config.mk rather than including 4.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-21 14:07:29 -05:00
Lokesh Vutla
140d76a9ee board: ti: amx3xx: Remove multiple EEPROM reads
Detect the board very early and avoid reading eeprom multiple times.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-21 13:59:25 -05:00
Lokesh Vutla
b64a7cb92d ARM: AMx3xx: Centralize early clock initialization
This is similar to Commit 93e6253d11 ("ARM: OMAP4/5: Centralize
early clock initialization") that was done for OMAP4+, reflecting the same
for AM33xx and AM43xx SoCs to centralize clock initialization.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add setup_early_clocks that calls setup_clocks_for_console for
        ti81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-21 13:58:55 -05:00
Lokesh Vutla
c704a99dff ARM: AMx3xx: Allow arch specific code to use early DM
Early system initialization is being done before initf_dm is being called
in U-Boot. Then system will fail to boot if any of the DM enabled driver
is being called in this system initialization code. So, rearrange the
code a bit so that DM enabled drivers can be called during early system
initialization. This is inspired by commit e850ed82bc ("ARM: OMAP4+: Allow
arch specific code to use early DM")

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-21 09:49:58 -05:00
Peng Fan
97c16dc8bf imx: mx6ull: update the REFTOP_VBGADJ setting
According to design team, we need to set REFTOP_VBGADJ
in PMU MISC0 according to the REFTOP_TRIM[2:0] fuse. the
actually table is as below:

  '000" - set REFTOP_VBGADJ[2:0] to 3'b000
  '001" - set REFTOP_VBGADJ[2:0] to 3'b001
  '010" - set REFTOP_VBGADJ[2:0] to 3'b010
  '011" - set REFTOP_VBGADJ[2:0] to 3'b011
  '100" - set REFTOP_VBGADJ[2:0] to 3'b100
  '101" - set REFTOP_VBGADJ[2:0] to 3'b101
  '110" - set REFTOP_VBGADJ[2:0] to 3'b110
  '111" - set REFTOP_VBGADJ[2:0] to 3'b111

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
2016-11-16 20:53:55 +01:00
Ye.Li
27e3a3c7f8 imx: mx6sx: Disable ENET clock before switching clock parent
Need to gate ENET clock when switching to a new clock parent, because
the mux is not glitchless.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye.Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-11-16 20:53:55 +01:00
Jagan Teki
aec9a0f19f sunxi: Rename CONFIG_SUNXI to CONFIG_ARCH_SUNXI
CONFIG_SUNXI -> CONFIG_ARCH_SUNXI
and removed CONFIG_SUNIX from config_whitelist.txt

Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-10-30 11:38:04 +01:00
Jagan Teki
f160c5c8b9 engicam: icorem6: Add DM_GPIO, DM_MMC support
Add DM_GPIO, DM_MMC support for u-boot and disable for SPL.

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-10-26 16:53:16 +02:00
Jagan Teki
e88edc7b4a arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
i.CoreM6 DualLite/Solo modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU           NXP i.MX6 DL, 800MHz
RAM           1GB, 32, 64 bit, DDR3-800/1066
NAND          SLC,512MB
Power supply  Single 5V
MAX LCD RES   FULLHD

and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-10-26 16:53:16 +02:00
Jagan Teki
f4b7532f82 arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
Boot Log for i.CoreM6 DualLite/Solo Starter Kit:
-----------------------------------------------

U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1

U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)

CPU:   Freescale i.MX6SOLO rev1.3 at 792MHz
CPU:   Industrial temperature grade (-40C to 105C) at 31C
Reset cause: POR
DRAM:  256 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
switch to partitions #0, OK
mmc0 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage
6741808 bytes read in 341 ms (18.9 MiB/s)
Booting from mmc ...
reading imx6dl-icore.dtb
30600 bytes read in 19 ms (1.5 MiB/s)
   Booting using the fdt blob at 0x18000000
   Using Device Tree in place at 18000000, end 1800a787

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0

Boot Log for i.CoreM6 Quad/Dual Starter Kit:
--------------------------------------------

U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1

U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)

CPU:   Freescale i.MX6Q rev1.2 at 792MHz
CPU:   Industrial temperature grade (-40C to 105C) at 28C
Reset cause: POR
DRAM:  512 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
icorem6qdl>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-10-26 16:53:16 +02:00
Tom Rini
711b534120 Merge git://git.denx.de/u-boot-fsl-qoriq
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	include/configs/ls1021aqds.h
	include/configs/ls1021atwr.h
2016-10-12 08:29:42 -04:00
Tom Rini
f5fd45ff64 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-10-08 09:33:37 -04:00
Lokesh Vutla
1f95770807 ARM: AM437X: Add Silicon ID support
Add silicon ID code for AM437x silicon. This can be used to print
the cpu info using CONFIG_DISPLAY_CPUINFO.
Also printing "CPU :" along with cpu name in order to be consistent
with other OMAP platforms.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-10-08 09:33:36 -04:00
Stefan Agner
d7255e8ddb ARM: vf610: use strcpy for soc environment variable
To create the soc environment variable we concatenate two strings
on the stack. So far, strcat has been used for the first string as
well as for the second string. Since the variable on the stack is
not initialized, the first strcat may not start using the first
entry in the character array. This then could lead to an buffer
overflow on the stack.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2016-10-07 15:56:52 +02:00
Keerthy
1dbc40e7d2 ARM: OMAP5+: Override switch_to_hypervisor function
Override the switch_to_hypervisor function to switch cpu to hypervisor
mode using the available ROM code hook early in the boot phase before
the boot loader checks for HYP mode.

Based on the work done by Jonathan Bergsagel jbergsagel@ti.com.

Cc: beagleboard-x15@googlegroups.com
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06 20:58:16 -04:00
Keerthy
d31d4a2d75 ARM: Introduce function to switch to hypervisor mode
On some of the SoCs one cannot enable hypervisor mode directly from the
u-boot because the ROM code puts the chip to supervisor mode after it
jumps to boot loader. Hence introduce a weak function which can be
overridden based on the SoC type and switch to hypervisor mode in a
custom way.

Cc: beagleboard-x15@googlegroups.com
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06 20:58:16 -04:00
Keerthy
859c70df23 omap: Set appropriate cache configuration for LPAE and non-LAPE cases
Cache configuration methods is different for LPAE and non-LPAE cases.
Hence the bits and the interpretaion is different for two cases.
In case of non-LPAE mode short descriptor format is used and we need
to set Cache and Buffer bits.

In the case of LPAE the cache configuration happens via MAIR0 lookup.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06 20:57:44 -04:00
Keerthy
c268a9bde0 omap: Remove hardcoding of mmu section shift to 20
As of now the mmu section shift is hardcoded to 20 but with LPAE
coming into picture this can be different. Hence replacing 20 with
MMU_SECTION_SHIFT macro.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06 20:57:43 -04:00
Siarhei Siamashka
22a402f00c ARM: Respect CONFIG_SPL_STACK define in lowlevel_init.S
The SPL and U-Boot proper may use different initial stack
locations, which are configured via CONFIG_SPL_STACK and
CONFIG_SYS_INIT_SP_ADDR defines. The lowlevel_init.S
code needs to handle this in the same way as crt0.S

Without this fix, setting the U-Boot stack location to some
place, which is not safely accessible by the SPL (such as
the DRAM), causes a very early SPL deadlock.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06 20:57:36 -04:00
Simon Glass
a807ab3303 spl: Kconfig: Move SPL_DISPLAY_PRINT to Kconfig
Move this option to Kconfig and tidy up existing uses. Also add a function
comment to the header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06 14:48:21 -04:00
York Sun
53d76829d5 armv7: ls1021a: Move DDR config options to Kconfig
Move DDR3, DDR4 and related config options to Kconfig and clean up
existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06 09:59:11 -07:00
York Sun
f534b8f5fd arm: Move SYS_FSL_SRDS_* and SYS_HAS_SERDES to Kconfig
Move these options to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06 09:59:11 -07:00
York Sun
25af7dc193 arm: Move SYS_FSL_IFC_BANK_COUNT to Kconfig
Move this option to Kconfig and clean up existing uses.
This option is also used by PowerPC SoCs.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06 09:59:11 -07:00
York Sun
b4b60d06c6 arm: Move MAX_CPUS to Kconfig
Move MAX_CPUS option to Kconfig and clean up existing uses for ARM. This
option is used by Freescale Layerscape SoCs.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06 09:59:10 -07:00
York Sun
fb2bf8c2c6 arm: Move FSL_LSCH2 FSL_LSCH3 to Kconfig
Move these options to Kconfig and create a sub-menu to avoid name
conflict with other architectures.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06 09:59:10 -07:00
York Sun
4a4441765d arm: Fix Kconfig for proper display menu
Some config options should not have prompt. They are selected by choosing
target.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06 09:59:10 -07:00
Xiaoliang Yang
f85a8e8d1d armv7: LS1021a: enable i-cache in start.S
Delete CONFIG_SKIP_LOWLEVEL_INIT define in ls1021atwr.h and
ls1021aqds.h can let it run cpu_init_cp15 to enable i-cache. First
stage of u-boot can run faster after that. There is a description
about skip lowlevel init in board/freescale/ls1021atwr/README.

Signed-off-by: Xiaoliang Yang <xiaoliang.yang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06 09:55:08 -07:00
Albert ARIBAUD \(3ADEV\)
ed0c2c0a9e tools: mkimage: add support for Vybrid image format
This format can be flashed directly at address 0 of
the NAND FLASH, as it contains all necessary headers.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2016-10-06 09:06:16 +02:00
Peng Fan
f15ece388f imx: imx6ul: disable POR_B internal pull up
>From TO1.1, SNVS adds internal pull up control for POR_B,
the register filed is GPBIT[1:0], after system boot up,
it can be set to 2b'01 to disable internal pull up.
It can save about 30uA power in SNVS mode.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 19:37:39 +02:00
Stefan Agner
81c4eccb55 imx: mx6: fix USB bmode to use reserved value
Currently the bmode "usb" uses BOOT_CFG1 to 0x01, -which means
BOOT_CFG1[7:4] is set to b0000. According to Table 8-7 Boot
Device Selection this is NOR/OneNAND and not Reserved.

Use 0x10 which leads to b0001, which is a Reserved boot device.
With that the SoC reliably falls back to the serial loader.

Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
2016-10-04 19:31:23 +02:00
Peng Fan
55a42b33f2 arm: imx: add i.MX6ULL 14x14 EVK board support
Add i.MX6ULL EVK board support:
Add device tree file, which is copied from NXP Linux.
Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR.
The uart iomux settings are still keeped in board file.

Boot Log:
U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800)

CPU:   Freescale i.MX6ULL rev1.0 at 396MHz
CPU:   Commercial temperature grade (0C to 95C) at 15C
Reset cause: POR
Model: Freescale i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM:  512 MiB
MMC:   initialized IMX pinctrl driver
FSL_SDHC: 0, FSL_SDHC: 1
In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
=> mmc dev 1
switch to partitions #0, OK
mmc1 is current device

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:42:07 +02:00
Peng Fan
5b66482d44 imx: imx6ull: adjust the ldo 1.2v bandgap voltage
Per to design team, on i.MX6UL, the LDO 1.2V bandgap voltage
is 30mV higher, so we need to adjust the REFTOP_VBGADJ(anatop
MISC0 bit[6:4]) setting to 2b'110.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:01 +02:00
Peng Fan
3974b7f6e0 imx: mx6ull: update clock settings and CCM register map
Update Clock settings and CCM register map for i.MX6ULL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:00 +02:00
Peng Fan
b4714616a0 imx: mx6ull: adjust POR_B setting for i.MX6ULL
Adjust POR_B settings on i.MX6ULL according to IC design
team's suggestion:

2'b00 :  always PUP100K
2'b01 :  PUP100K when PMIC_ON_REQ || SOC_NOT_FAIL
2'b10 :  always disable PUP100K
2'b11 :  PDN100K when SOC_FAIL, PUP100K when SOC_NOT_FAIL -- recommended setting

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:00 +02:00
Peng Fan
6615da4da3 imx: mx6ull: misc soc update
Update misc SOC related settings for i.MX6ULL, such as FEC mac address,
cpu speed grading and mmdc channel mask clearing.

Also update s_init to skip pfd reset.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:00 +02:00
Peng Fan
00ffa56d4b imx: mx6ul: using runtime check when configuring PMIC_STBY_REQ
Since MX6ULL select MX6UL, we can not use IS_ENABLED(CONFIG_MX6UL) here,
because this piece code is only for i.MX6UL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:00 +02:00
Peng Fan
cdf33c9403 imx: mx6ull: skip setting ahb clock
Rom already initialized clock at 396M and 132M for arm core and ahb,
so skip setting them again in U-Boot.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:00 +02:00
Ye Li
51db46035c imx: mx6ull: add kconfig entry for MX6ULL
i.MX6ULL is derivative from i.MX6UL, so select MX6UL for MX6ULL.
If need to differenate MX6ULL from MX6UL, use CONFIG_MX6ULL

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:00 +02:00
Andrew F. Davis
ba84e6ae1f ti: omap-common: Allow AM33xx devices to be built securely
Like OMAP54xx and AM43xx family SoCs, AM33xx based SoCs have high
security enabled models. Allow AM33xx devices to be built with
HS Device Type Support.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-10-02 08:10:02 -04:00
Andrew F. Davis
7e5a0bfbd2 am33xx: config.mk: Fix option used to enable SPI SPL image type
The option SPL_SPI_SUPPORT is used to enable support in SPL for loading
images from SPI flash, it should not be used to determine the build type
of the SPL image itself. The ability to read images from SPI flash does
not imply the SPL will be booted from SPI flash.

Unconditionally build SPI flash compatible SPL images.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-02 08:10:00 -04:00
Andrew F. Davis
9eda25181d am33xx: config.mk: Add support for additional secure boot image types
Depending on the boot media, different images are needed
for secure devices. The build generates u-boot*_HS_* files
as appropriate for the different boot modes.

For AM33xx devices additional image types are needed for
various SPL boot modes as the ROM checks for the name of
the boot mode in the file it loads.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-10-02 08:09:59 -04:00
Andrew F. Davis
b39a9ade5c Kconfig: Separate AM33XX SOC config from target board config
The config option AM33XX is used in several boards and should be
defined as a stand-alone option for this SOC. We break this out
from target boards that use this SoC and common headers then enable
AM33XX on in all the boards that used these targets to eliminate any
functional change with this patch.

This is similar to what has already been done in
9de852642cae ("arm: Kconfig: Add support for AM43xx SoC specific Kconfig")
and is done for the same reasons.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-02 08:09:58 -04:00
Daniel Allred
6696139409 ARM: omap5: add fdt secure dram reservation fixup
Adds a secure dram reservation fixup for secure
devices, when a region in the emif has been set aside
for secure world use. The size is defined by the
CONFIG_TI_SECURE_EMIF_TOTAL_REGION_SIZE config option.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-02 08:09:57 -04:00
Daniel Allred
501f0ef304 ARM: DRA7: Add secure emif setup calls
After EMIF DRAM is configured, but before it is used,
calls are made on secure devices to reserve any configured
memory region needed by the secure world and then to lock the
EMIF firewall configuration. If any other firewall
configuration needs to be applied, it must happen before the
lock call.

Signed-off-by: Daniel Allred <d-allred@ti.com>
2016-10-02 08:09:56 -04:00
Daniel Allred
6d132b2b09 arm: omap5: secure API for EMIF memory reservations
Create a few public APIs which rely on secure world ROM/HAL
APIs for their implementation. These are intended to be used
to reserve a portion of the EMIF memory and configure hardware
firewalls around that region to prevent public code from
manipulating or interfering with that memory.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-02 08:09:55 -04:00
Daniel Allred
4c854b6199 ti: omap5: Add Kconfig options for secure EMIF reservations
Adds start address and size config options for setting aside
a portion of the EMIF memory space for usage by security software
(like a secure OS/TEE). There are two sizes, a total size and a
protected size. The region is divided into protected (secure) and
unprotected (public) regions, that are contiguous and start at the
start address given. If the start address is zero, the intention
is that the region will be automatically placed at the end of the
available external DRAM space.

Signed-off-by: Daniel Allred <d-allred@ti.com>
2016-10-02 08:09:51 -04:00
B, Ravi
6f8387f120 dra7x: boot: add dfu bootmode support
This patch enables the DFU boot mode support
for dra7x platform.

Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-27 23:30:20 +02:00
Tom Rini
cbe7706ab8 Merge git://git.denx.de/u-boot-fsl-qoriq
trini: Drop local memset() from
examples/standalone/mem_to_mem_idma2intr.c

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-26 17:10:56 -04:00
York Sun
295a24b3d6 armv7: ls102xa: Rename GIC_ADDR and DCSR_RCPM_ADDR
Instead of using CONFIG_* name space, rename these two macros to
SYS_FSL_* space.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-26 08:53:07 -07:00
York Sun
5e8bd7e117 armv7: ls1021a: Convert CONFIG_LS1_DEEP_SLEEP to Kconfig option
Move this option to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-26 08:53:07 -07:00
York Sun
0a37cf8f27 Convert CONFIG_SYS_FSL_ERRATUM_A010315 to Kconfig option
Move this option to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
2016-09-26 08:53:07 -07:00
Masahiro Yamada
1221ce459d treewide: replace #include <asm/errno.h> with <linux/errno.h>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content.  (both just wrap <asm-generic/errno.h>)

Replace all include directives for <asm/errno.h> with <linux/errno.h>.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-23 17:55:42 -04:00
Masahiro Yamada
63a7578e4e arch, board: squash lines for immediate return
Remove unneeded variables and assignments.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
2016-09-23 17:53:53 -04:00
Simon Glass
e00f76cee9 Convert CONFIG_SPL_SERIAL_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:19 -04:00
Simon Glass
2253797d28 Convert CONFIG_SPL_POWER_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:18 -04:00
Simon Glass
d6b9bd8923 Convert CONFIG_SPL_NAND_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:14 -04:00
Simon Glass
1fdf7c64ed Convert CONFIG_SPL_MMC_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:13 -04:00
Simon Glass
cc4288ef42 Convert CONFIG_SPL_LIBGENERIC_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:12 -04:00
Simon Glass
1646eba85c Convert CONFIG_SPL_LIBDISK_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:12 -04:00
Simon Glass
77d2f7f507 Convert CONFIG_SPL_LIBCOMMON_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:11 -04:00
Simon Glass
9c21df1547 Convert CONFIG_SPL_I2C_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:10 -04:00
Simon Glass
53b5bf3c1d Convert CONFIG_SPL_GPIO_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:10 -04:00
Simon Glass
ae56db5f1c Convert CONFIG_SPL_FAT_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:10 -04:00
Simon Glass
75eba2c45e Convert CONFIG_SPL_EXT_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:09 -04:00
Hongbo Zhang
214ffae02d nxp: ls102xa: add LS1 PSCI system suspend
The deep sleep function of LS1 platform, is mapped into PSCI system
suspend function, this patch adds implementation of it.

Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-14 14:08:04 -07:00
Hongbo Zhang
d7b006393e nxp: ls102xa: add EPU Finite State Machine
The EPU Finite State Machie (FSM) is used in both the last stage of
system suspend and the earliest stage of system resume.

Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-14 14:07:51 -07:00
Hongbo Zhang
d38def1f34 armv7: psci: make v7_flush_dcache_all public for all psci code
The v7_flush_dcache_all function will be called by ls102xa platform system
suspend, it is necessary to make it a public call instead of a local one, but
changing the LENTRY to ENTRY isn't enough, because there is another one using
the same name, so this one gets a psci_ prefix.

Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-14 14:07:29 -07:00
Hou Zhiqiang
b392a6d4b0 fsl-layerscape: Add workaround for PCIe erratum A010315
As the access to serders protocol unselected PCIe controller will
hang. So disable the R/W permission to unselected PCIe controller
including its CCSR, IO space and memory space according to the
serders protocol field of RCW.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-14 14:07:13 -07:00
Hou Zhiqiang
341238fd13 arm: fsl-layerscape: move forward the non-secure access permission setup
Move forward the basic non-secure access enable operation, so the
subsequent individual device access permission can override it.
And collect the dispersed callers in board level, and then move
them to SoC level.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-14 14:06:56 -07:00
Hou Zhiqiang
71fe22256c fsl: serdes: ensure accessing the initialized maps of serdes protocol
Up to now, the function is_serdes_configed() doesn't check if the map
of serdes protocol is initialized before accessing it. The function
is_serdes_configed() will get wrong result when it was called before
the serdes protocol maps initialized. As the first element of the map
isn't used for any device, so use it as the flag to indicate if the
map has been initialized.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-14 14:06:49 -07:00
Tom Rini
16f416661e Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-09-09 09:45:32 -04:00
Masahiro Yamada
1544698816 ARM: armv7: move ARMV7_PSCI_NR_CPUS to Kconfig
Move this option to Kconfig and set its default value to 4; this
increases the number of supported CPUs for some boards.

It consumes 1KB memory per CPU for PSCI stack, but it should not
be a big deal, given the amount of memory used for the modern OSes.

Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-07 08:48:54 -04:00
Masahiro Yamada
217f92bb79 ARM: armv7: move CONFIG_ARMV7_PSCI to Kconfig
Add ARCH_SUPPORT_PSCI as a non-configurable option that platforms
can select.  Then, move CONFIG_ARMV7_PSCI, which is automatically
enabled if both ARMV7_NONSEC and ARCH_SUPPORT_PSCI are enabled.

Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-07 08:48:51 -04:00
Fabio Estevam
edf0093732 mx6: ddr: Allow changing REFSEL and REFR fields
Currently MX6 SPL DDR initialization hardcodes the REF_SEL and
REFR fields of the MDREF register as 1 and 7, respectively for
DDR3 and 0 and 3 for LPDDR2.

Looking at the MDREF initialization done via DCD we see that
boards do need to initialize these fields differently:

$ git grep 0x021b0020 board/
board/bachmann/ot1200/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/ccv/xpress/imximage.cfg:DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x7800
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6qp.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6dlsabresd.cfg:DATA 4      0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6slevk/imximage.cfg:DATA 4 0x021b0020 0x00001800
board/freescale/mx6sxsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/freescale/mx6sxsabresd/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/warp/imximage.cfg:DATA 4 0x021b0020 0x00001800

So introduce a mechanism for users to be able to configure
REFSEL and REFR fields as needed.

Keep all the mx6 SPL users in their current REF_SEL and REFR values,
so no functional changes for the existing users.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
2016-09-06 18:22:48 +02:00
Akshay Bhat
ff3832205e arm: imx: Add support for Advantech DMS-BA16 board
Add support for Advantech DMS-BA16 board. The board is based on Advantech
BA16 module which has a i.MX6D processor. The board supports:
 - FEC Ethernet
 - USB Ports
 - SDHC and MMC boot
 - SPI NOR
 - LVDS and HDMI display

Basic information about the module:
 - Module manufacturer: Advantech
 - CPU: Freescale ARM Cortex-A9 i.MX6D
 - SPECS:
     Up to 2GB Onboard DDR3 Memory;
     Up to 16GB Onboard eMMC NAND Flash
     Supports OpenGL ES 2.0 and OpenVG 1.1
     HDMI, 24-bit LVDS
     1x UART, 2x I2C, 8x GPIO,
     4x Host USB 2.0 port, 1x USB OTG port,
     1x micro SD (SDHC),1x SDIO, 1x SATA II,
     1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: u-boot@lists.denx.de
Cc: sbabic@denx.de
2016-09-06 18:22:48 +02:00
Tom Rini
c98b171e10 Merge branch 'rmobile' of git://git.denx.de/u-boot-sh
[trini: Drop CMD_BOOTI as it's now on by default on ARM64]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-08-20 16:40:34 -04:00
Lokesh Vutla
c359ae5e8b ARM: OMAP4+: vcores: Remove duplicated code
There is no reason to duplicate code for DRA7xx platforms as there
can be Rail grouping. The maximum voltage detection algorithm can still
be run on other platforms with no Rail grouping and does not harm as
it gives the same result.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-08-20 14:03:25 -04:00
Lokesh Vutla
5328717cde ARM: OMAP5+: vcores: Drop unnecessary #ifndefs
gpio_en field is introduced to detect if pmic is controlled by GPIO.
Make this field 0 on all TPS659* pmics available on DRA7/OMAP5 based platforms
and remove the #ifndefs.

Reviewed-by:  Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-08-20 14:03:25 -04:00
Nobuhiro Iwamatsu
badbb63c2c ARM: rmobile: Move SoC sources to mach-rmobile
Move from arch/arm/cpu/armv7/rmobile/ to arch/arm/mach-rmobile/.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2016-08-17 10:25:28 +09:00
Masahiro Yamada
ab65006b08 kconfig: use bool instead of boolean for type definition attributes
Linux stopped the use of keyword 'boolean' in Kconfig.

Refer to commit 6341e62b212a2541efb0160c470e90bd226d5496 ("kconfig:
use bool instead of boolean for type definition attributes")
in Linux Kernel.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-08-12 09:23:49 -04:00
Stefan Agner
da91cfed54 ARM: non-sec: flush code cacheline aligned
Flush operations need to be cacheline aligned to take effect, make
sure to flush always complete cachelines. This avoids messages such
as:
CACHE: Misaligned operation at range [00900000, 009004d9]

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-08-12 09:22:15 -04:00
Tom Rini
584550d76a omap3: Drop omap3_evm_quick_* targets
These config targets were added well before the Kconfig migration began
as a way to demonstrate how to make these platforms work with cut down
features.  At this point in time they no longer serve a good purpose so
remove them.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-08-05 20:53:53 -04:00
Tom Rini
a2ea62e826 omap3: Move to select SUPPORT_SPL for all
In reality all omap3 platforms support SPL so move the select for this
up a level.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-08-05 07:27:29 -04:00
Masahiro Yamada
bb6b142fc1 treewide: move CONFIG_PHYS_64BIT to Kconfig
We need to ensure that CONFIG_PHYS_64BIT is configured via Kconfig so
that it is always available to the build system.  Otherwise we can run
into cases where we have inconsistent sizes of certain attributes.

Ravi Babu reported offset mismatch of struct dwc3 across files since
commit 95ebc253e6 ("types.h: move and redefine resource_size_t").
Since the commit, resource_addr_t points to phys_addr_t, whose size
is dependent on CONFIG_PHYS_64BIT for ARM architecture.

I tried my best to use "select" where possible (for example, ARMv8
architecture) because I think this kind of option is generally user-
unconfigurable.  However, I see some of PowerPC boards have 36BIT
defconfigs as well as 32BIT ones.  I moved CONFIG_PHYS_64BIT to the
defconfigs for such boards.

CONFIG_36BIT is no longer referenced, so all of the defines were
removed from CONFIG_SYS_EXTRA_OPTIONS.

Fixes: 95ebc253e6 ("types.h: move and redefine resource_size_t")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-05 07:27:25 -04:00
Tom Rini
a78cd86132 ARM: Rework and correct barrier definitions
As part of testing booting Linux kernels on Rockchip devices, it was
discovered by Ziyuan Xu and Sandy Patterson that we had multiple and for
some cases incomplete isb definitions.  This was causing a failure to
boot of the Linux kernel.

In order to solve this problem as well as cover any corner cases that we
may also have had a number of changes are made in order to consolidate
things.  First, <asm/barriers.h> now becomes the source of isb/dsb/dmb
definitions.  This however introduces another complexity.  Due to
needing to build SPL for 32bit tegra with -march=armv4 we need to borrow
the __LINUX_ARM_ARCH__ logic from the Linux Kernel in a more complete
form.  Move this from arch/arm/lib/Makefile to arch/arm/Makefile and add
a comment about it.  Now that we can always know what the target CPU is
capable off we can get always do the correct thing for the barrier.  The
final part of this is that need to be consistent everywhere and call
isb()/dsb()/dmb() and NOT call ISB/DSB/DMB in some cases and the
function names in others.

Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Sandy Patterson <apatterson@sightlogix.com>
Reported-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reported-by: Sandy Patterson <apatterson@sightlogix.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-08-05 07:23:57 -04:00
Lokesh Vutla
4d790788ce ARM: dra7xx: Change DPLL_PER_HS13 divider value
According to AM572x DM SPRS953A, QSPI bus speed can be 76.8MHz, hence
update QSPI input clock divider value (DPLL_PER_HS13) to provide 76.8MHz
clock, so that driver can use the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-30 00:15:00 +05:30
Tom Rini
4711e7f7af Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-07-28 08:45:00 -04:00
Stefan Agner
ae440ab02d colibri_imx7: add Colibri iMX7S/iMX7D module support
This commit adds support for the Toradex Computer on Modules
Colibri iMX7S/iMX7D. The two modules/SoC's are very similar hence
can be easily supported by one board. The board code detects RAM
size at runtime which is one of the differences between the two
boards. The board also uses the UART's in DTE mode, hence making
use of the new DTE support via serial DM.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2016-07-28 13:27:19 +02:00
Tom Rini
9c7a0a600b Merge git://git.denx.de/u-boot-fsl-qoriq 2016-07-26 17:34:28 -04:00
Hongbo Zhang
aeb901f2a6 ARMv7: PSCI: ls102xa: add more PSCI v1.0 functions implemention
This patch implements PSCI functions for ls102xa SoC following PSCI v1.0,
they are as the list:
    psci_version,
    psci_features,
    psci_cpu_suspend,
    psci_affinity_info,
    psci_system_reset,
    psci_system_off.

Tested on LS1021aQDS, LS1021aTWR.

Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-26 09:02:49 -07:00
Hongbo Zhang
7e742c276d ARMv7: PSCI: ls102xa: check target CPU ID before further operations
The input parameter CPU ID needs to be validated before furher oprations such
as CPU_ON, this patch introduces the function to do this.

Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-26 09:02:44 -07:00
Hongbo Zhang
116339d460 ARMv7: PSCI: add PSCI v1.0 functions skeleton
This patch adds all the PSCI v1.0 functions in to the common framework, with
all the functions returning "not implemented" by default, as a common framework
all the dummy functions are added here, it is up to every platform developer to
decide which version of PSCI and which functions to implement.

Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-26 09:02:39 -07:00
Russ Dill
335b4e53c9 ARM: am33xx: Always inhibit init/refresh during DDR phy init
A couple of commits have modified the am33xx/am437x ddr2/ddr3
initialization path to fix certain issues, but have had the side effect
of causing L3 noc errors during initialization. The two commits are:

69b918 "am33xx,ddr3: fix ddr3 sdram configuration"
fc46ba "arm: am437x: Enable hardware leveling for EMIF"

The EMIF_REG_INITREF_DIS_MASK bit still needs to be set for all
platforms. This delays initialization and refresh until a later stage.
The 500us timer can be programmed for platforms that require it
and for platforms that don't require it. It is currently hardcoded
for 400MHz systems. For systems with a higher memory frequency
this needs to be a larger value, and for systems with a lower
memory frequency this can be a lower value. This can be
considered a separate issue and corrected in a later commit.

Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-25 12:00:06 -04:00
Russ Dill
3325b06556 ARM: am33xx: Fix DDR init delay placement
The delay needs to be before the write to ref_ctrl register
which initiates refreshes. An improper initialization sequence
generates an L3 noc error.

Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-25 12:00:06 -04:00
Andreas Dannenberg
38d592fc33 arm: omap5: fix build dependency for secure devices
Commit 17c2987 introduces an undesired dependency on CONFIG_SPL_LOAD_FIT
when building U-Boot for AM57xx and DRA7xx high-security (HS) devices that
causes the build to break when that option is not active. Fix this issue
by only building the u-boot_HS.img target when building U-Boot into an
actual FIT image.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-22 14:46:26 -04:00
Andreas Dannenberg
8b76d23ebd arm: am4x: fix build dependency for secure devices
Commit e29878f introduces an undesired dependency on CONFIG_SPL_LOAD_FIT
when building U-Boot for AM43xx high-security (HS) devices that causes the
build to break when that option is not active. Fix this issue by only
building the u-boot_HS.img target when building U-Boot into an actual
FIT image.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-22 14:46:26 -04:00
Ladislav Michl
9a9d394639 armv7: simplify identify_nand_chip
Use newly introduced function

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2016-07-22 14:46:11 -04:00
Ladislav Michl
22d6ac490e armv7: armv7: introduce set_gpmc_cs0
Allow boards to runtime detect flash type.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2016-07-22 14:46:11 -04:00
Ladislav Michl
0568dd0663 armv7: make gpmc_cfg const
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
[trini: Adapt am33xx, duovero, omap_zoom1]
Signed-off-by: Tom Rini <trini@konsulko.com>

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-07-22 14:46:00 -04:00
Ladislav Michl
b1509e3a4a armv7: add reset timeout to identify_nand_chip
identify_nand_chip hangs forever in loop when NAND is not present.
As IGEPv2 comes either with NAND or OneNAND flash, add reset timeout
to let function fail gracefully allowing caller to know NAND is
not present. On NAND equipped board, reset succeeds on first read,
so 1000 loops seems to be safe timeout.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2016-07-22 09:53:00 -04:00
Fabio Estevam
8f2e2f15ff mx6: clock: Fix the logic for reading axi_alt_sel
According to the IMX6DQRM Reference Manual, the description
of bit 7 (axi_alt_sel) of the CCM_CBCDR register is:

"AXI alternative clock select
0 pll2 396MHz PFD will be selected as alternative clock for AXI root clock
1 pll3 540MHz PFD will be selected as alternative clock for AXI root clock "

The current logic is inverted, so fix it to match the reference manual.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-20 18:26:37 +02:00
Tom Rini
66669fcf80 Merge git://git.denx.de/u-boot-fsl-qoriq
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	arch/arm/cpu/armv8/Makefile
	arch/arm/lib/bootm-fdt.c
2016-07-19 16:38:57 -04:00
Hou Zhiqiang
45684ae37b ARMv8/PSCI: Fixup the device tree for PSCI
Set the enable-method in the cpu node to PSCI, and create device
node for PSCI, when PSCI was enabled.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-19 11:34:07 -07:00
Stefan Agner
be1a17ff68 mx7_common: use Kconfig for ARMv7 non-secure mode
Use existing Kconfig symbols to let the user configure whether to
build a U-Boot with non-secure mode support or not. This also allows
to enable virtualization extension easily.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2016-07-19 19:52:15 +02:00
Stefan Agner
ec7fde3ebf mx7: set soc environment according to exact SoC type
This can be useful if the same U-Boot binary is used for boards
available with a i.MX 7Solo and i.MX 7Dual.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-19 19:52:14 +02:00
Robert P. J. Day
62a3b7dd08 Various, unrelated tree-wide typo fixes.
Fix a number of typos, including:

     * "compatble" -> "compatible"
     * "eanbeld" -> "enabled"
     * "envrionment" -> "environment"
     * "FTD" -> "FDT" (for "flattened device tree")
     * "ommitted" -> "omitted"
     * "overriden" -> "overridden"
     * "partiton" -> "partition"
     * "propogate" -> "propagate"
     * "resourse" -> "resource"
     * "rest in piece" -> "rest in peace"
     * "suport" -> "support"
     * "varible" -> "variable"

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2016-07-16 09:43:12 -04:00
Tom Rini
1f9ef0dca0 Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2016-07-15 10:44:01 -04:00
Chen-Yu Tsai
b7073965a3 ARM: PSCI: Make psci_get_cpu_stack_top local to armv7/psci.S
Now that we have a secure data section for storing variables, there
should be no need for platform code to get the stack address.

Make psci_get_cpu_stack_top a local function, as it should only be
used in armv7/psci.S and only by psci_stack_setup.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 15:54:58 +02:00
Chen-Yu Tsai
6e6622de16 ARM: PSCI: Switch to per-CPU target PC storage in secure data section
Now that we have a secure data section and space to store per-CPU target
PC address, switch to it instead of storing the target PC on the stack.

Also save clobbered r4-r7 registers on the stack and restore them on
return in psci_cpu_on for Tegra, i.MX7, and LS102xA platforms.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 15:54:58 +02:00
Chen-Yu Tsai
45c334e6b2 ARM: PSCI: Add helper functions to access per-CPU target PC storage
Now that we have a data section, add helper functions to save and fetch
per-CPU target PC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 15:54:58 +02:00
Chen-Yu Tsai
afc1f65f50 ARM: Move __secure definition to common asm/secure.h
sunxi and i.mx7 both define the __secure modifier to put functions in
the secure section. Move this to a common place.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 15:54:57 +02:00
Chen-Yu Tsai
28f9035732 ARM: PSCI: Remove unused psci_text_end symbol
psci_text_end was used to calculate the PSCI stack address following the
secure monitor text. Now that we have an explicit secure stack section,
this is no longer used.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 15:54:57 +02:00
Chen-Yu Tsai
8c0ef7fad6 ARM: PSCI: Allocate PSCI stack in secure stack section
Now that we have a secure stack section that guarantees usable memory,
allocate the PSCI stacks in that section.

Also add a diagram detailing how the stacks are placed in memory.

Reserved space for the target PC remains unchanged. This should be
moved to global variables within a secure data section in the future.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 15:54:57 +02:00
Chen-Yu Tsai
94a389b257 sunxi: Move remaining PSCI assembly code to C
This patch finishes the rewrite of sunxi specific PSCI parts into C
code.

The assembly-only stack setup code has been factored out into a common
function for ARMv7. The GIC setup code can be renamed as psci_arch_init.
And we can use an empty stub function for psci_text_end.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 15:54:56 +02:00
Chen-Yu Tsai
b52813239c ARM: PSCI: Split out common stack setup code from psci_arch_init
Every platform has the same stack setup code in assembly as part of
psci_arch_init.

Move this out into a common separate function, psci_stack_setup, for
all platforms. This will allow us to move the remaining parts of
psci_arch_init into C code, or drop it entirely.

Also provide a stub no-op psci_arch_init for platforms that don't need
their own specific setup code.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 15:54:56 +02:00
Simon Glass
6b424611a8 arm: Don't invalidate unaligned cache regions
At present armv7 will unhappily invalidate a cache region and print an
error message. Make it skip the operation instead, as it does with other
cache operations.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
2016-07-14 18:33:10 -04:00
Simon Glass
397b5697ad arm: Move check_cache_range() into a common place
This code is common, so move it into a common file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
2016-07-14 18:33:09 -04:00
Lokesh Vutla
663f6fcaf0 ARM: OMAP5+: Enable errata i727
Errata i727 is applicable on all OMAP5 and DRA7 variants but enabled only
on OMAP5 ES1.0. So, enable it on all platforms.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:45 -04:00
Madan Srinivas
e29878fc47 arm: am4x: add U-Boot FIT signing and SPL image post-processing
Modify the SPL build procedure for AM437x high-security (HS) device
variants to create a secure u-boot_HS.img FIT blob that contains U-Boot
and DTB artifacts signed (and optionally encrypted) with a TI-specific
process based on the CONFIG_TI_SECURE_DEVICE config option and the
externally-provided image signing tool.

Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:23 -04:00
Andreas Dannenberg
17c2987336 arm: omap5: add U-Boot FIT signing and SPL image post-processing
Modify the SPL build procedure for AM57xx and DRA7xx high-security (HS)
device variants to create a secure u-boot_HS.img FIT blob that contains
U-Boot and DTB artifacts signed with a TI-specific process based on the
CONFIG_TI_SECURE_DEVICE config option and the externally-provided image
signing tool.

Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:22 -04:00
Andreas Dannenberg
bf9ec864f4 arm: omap-common: Update to generate secure U-Boot FIT blob
Adds commands so that when a secure device is in use and the SPL is
built to load a FIT image (with combined U-Boot binary and various
DTBs), these components that get fed into the FIT are all processed to
be signed/encrypted/etc. as per the operations performed by the
secure-binary-image.sh script of the TI SECDEV package. Furthermore,
perform minor comments cleanup to make better use of the available
space.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-14 18:22:20 -04:00
Andreas Dannenberg
1bb0a21b46 arm: omap-common: secure ROM signature verify API
Adds an API that verifies a signature attached to an image (binary
blob). This API is basically a entry to a secure ROM service provided by
the device and accessed via an SMC call, using a particular calling
convention.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:19 -04:00
Andreas Dannenberg
d86f7afda4 arm: omap-common: add secure rom call API for secure devices
Adds a generic C-callable API for making secure ROM calls on OMAP and
OMAP-compatible devices. This API provides the important function of
flushing the ROM call arguments to memory from the cache, so that the
secure world will have a coherent view of those arguments. Then is
simply calls the omap_smc_sec routine.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:19 -04:00
Daniel Allred
51d0638650 arm: omap-common: add secure smc entry
Add an interface for calling secure ROM APIs across a range of OMAP and
OMAP compatible high-security (HS) device variants. While at it, also
perform minor cleanup/alignment without any change in functionality.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:18 -04:00
Daniel Allred
ec6f61003b arm: cache: add missing dummy functions for when dcache disabled
Adds missing flush_dcache_range and invalidate_dcache_range dummy
(empty) placeholder functions to the #else portion of the #ifndef
CONFIG_SYS_DCACHE_OFF, where full implementations of these functions
are defined.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:17 -04:00
Peng Fan
1f17562796 imx6: clock: typo fix
Typo fix, "PPL2 -> PLL2"

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-07-12 17:58:50 +02:00
Stefano Babic
876a25d289 mx6: Add Phytec PCM058 i.MX6 Quad
Add Phytec-i.MX6 SOM with NAND

  Support:
   - 1GB RAM
   - Ethernet
   - SPI-NOR Flash
   - NAND (1024 MB)
   - external SD
   - UART

Signed-off-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-12 17:58:48 +02:00
Stefano Babic
8be4f40ecf mx6: add support for el6x board
Custom Board based on MX6 Dual, 1GB RAM and eMMC.

There are two variants of the board with and without
PCIe (ZC5202 and ZC5601).

Signed-off-by: Stefano Babic <sbabic@denx.de>
2016-07-12 17:58:48 +02:00
Marek Vasut
2b1cdafa9f common: Pass the boot device into spl_boot_mode()
The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.

The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant]
Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-26 20:17:22 +02:00
Steve Rae
8ada4e0ee6 arm: bcm235xx: update clock framework
The handling of the "usage counter" is incorrect, and the clock should
only be disabled when transitioning from 1 to 0.

Reported-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
2016-06-24 17:24:38 -04:00
Chris Brand
77a1a677a6 arm: bcm235xx: fix kps ccu
The Kona Peripheral Slave CCU has 4 policy mask registers, not 8.

Signed-off-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
2016-06-24 17:24:37 -04:00
Masahiro Yamada
ec048369e2 ARM: armv7: refactor Makefile slightly
Use Kbuild standard style where possible.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-24 17:24:34 -04:00
Daniel Gorsulowski
85a2f772c2 omap3: bugfix in timer on rollover
Signed-off-by: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
2016-06-24 17:21:55 -04:00
Chen-Yu Tsai
4257f5f8f6 sunxi: Add PSCI implementation in C
To make the PSCI backend more maintainable and easier to port to newer
SoCs, rewrite the current PSCI implementation in C.

Some inline assembly bits are required to access coprocessor registers.
PSCI stack setup is the only part left completely in assembly. In theory
this part could be split out of psci_arch_init into a separate common
function, and psci_arch_init could be completely in C.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-20 22:44:00 +02:00
Chen-Yu Tsai
3424c3f299 sunxi: Add base address for GIC
Instead of hardcoding the GIC addresses in the PSCI implementation,
provide a base address in the cpu header.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-20 22:44:00 +02:00
Chen-Yu Tsai
0f3b894426 sunxi: Make CPUCFG_BASE macro names the same across families
Use SUNXI_CPUCFG_BASE across all families. This makes writing common
PSCI code easier.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-20 22:44:00 +02:00
Chen-Yu Tsai
778dc5f43e ARM: PSCI: save and restore clobbered registers in v7_flush_dcache_all
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-20 22:43:59 +02:00
Chen-Yu Tsai
dae08d2281 ARM: PSCI: use only r0 and r3 in psci_get_cpu_stack_top()
For psci_get_cpu_stack_top() to be usable in C code, it must adhere to
the ARM calling conventions. Since it could be called when the stack
is still unavailable, and the entry code to linux also expects r1 and
r2 to remain unchanged, stick to r0 and r3.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-20 22:43:59 +02:00
Lokesh Vutla
165bd7a1cc board: am57xx: Rename TARGET_BEAGLE_X15 as TARGET_AM57XX_EVM
board/am57xx supports all boards based on am57xx. Rename the taget
as TARGET_AM57XX_EVM.

Fixes: 74cc8b097d ("board: ti: beagle_x15: Rename to indicate support for TI am57xx evms")
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13 08:56:36 -04:00
Steve Rae
43486e4cd0 board: arm:: Add support for Broadcom BCM23550
Add support for the Broadcom BCM23550 board.

Signed-off-by: Steve Rae <srae@broadcom.com>
2016-06-13 08:56:02 -04:00
Tom Rini
fd9102dafe Merge branch 'master' of git://git.denx.de/u-boot-atmel 2016-06-13 08:50:58 -04:00
Simon Glass
b5bd09820c arm: Allow skipping of low-level init with I-cache on
At present CONFIG_SKIP_LOWLEVEL_INIT prevents U-Boot from calling
lowlevel_init(). This means that the instruction cache is not enabled and
the board runs very slowly.

What is really needed in many cases is to skip the call to lowlevel_init()
but still perform CP15 init. Add an option to handle this.

Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-12 23:49:38 +02:00
Keerthy
1428d83270 arm: dra7xx: Assign omap_vcores based on board type
Currently omap_vcores which holds pmic data is being assigned based
on the SoC type. PMIC is not a part of SoC. It is logical to
to assign omap_vcores based on board type. Hence over ride the
vcores_init function and assign omap_vcores based on the board type.

Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2016-06-12 13:14:57 -04:00
Tom Rini
3fc304b8d7 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-06-12 12:51:34 -04:00
Heiko Schocher
3a504d9639 mtd: nand: omap: allow to switch to BCH16
support in omap_nand_switch_ecc() also an eccstrength
from 16.

Signed-off-by: Heiko Schocher <hs@denx.de>
2016-06-09 13:53:12 -04:00
Heiko Schocher
a4475af5b4 armv7: omap-common: make SPL board_mmc_init() weak
make this function weak, so board code can setup in SPL
MMC init with board special values.

Signed-off-by: Heiko Schocher <hs@denx.de>
2016-06-09 13:53:09 -04:00
Heiko Schocher
694607b563 arm, am335x: Enable Spread Spectrum for the MPU
Enable Spread Spectrum for the MPU by calculating the required
values and setting the registers accordingly.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-09 13:53:07 -04:00
Tom Rini
d77fa2ff76 Merge http://git.denx.de/u-boot-samsung
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	configs/peach-pi_defconfig
	configs/peach-pit_defconfig
2016-06-06 13:39:43 -04:00
Ladislav Michl
e22455f0a6 armv7: fix order of OMAP die ID printing
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
2016-06-06 13:39:17 -04:00
Keerthy
61462cd772 arm: omap: Introduce vcores_init function
The pmic registers for variants of am57xx boards are different
hence we need to assign them carefully based on the board type.
Add a function to assign omap_vcores after the board detection.

Signed-off-by: Keerthy <j-keerthy@ti.com>
2016-06-02 21:42:18 -04:00
Anna, Suman
e42523f544 ARM: DRA7: Consolidate voltage macros across different SoCs
The voltage values for each voltage domain at an OPP is identical
across all the SoCs in the DRA7 family. The current code defines
one set of macros for DRA75x/DRA74x SoCs and another set for DRA72x
macros. Consolidate both these sets into a single set.

This is done so as to minimize the number of macros used when voltage
values will be added for other OPPs as well.

Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-02 21:42:17 -04:00
Anna, Suman
27c9596f68 ARM: DRA7: Define common macros for efuse register offsets
Define a set of common macros for the efuse register offsets
(different for each OPP) that are used to get the AVS Class 0
voltage values and ABB configuration values. Assign these
common macros to the register offsets for OPP_NOM by default
for all voltage domains. These common macros can then be
redefined properly to point to the OPP specific efuse register
offset based on the desired OPP to program a specific voltage
domain.

Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-02 21:42:16 -04:00
Roger Quadros
3599774eec dra7xx: Enable USB_PHY3 32KHz clock
DRA7xx has a 32KHz PHY clock for USB_PHY3 that must be enabled
for USB1 instance in Super-Speed.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2016-06-02 21:42:15 -04:00
Roger Quadros
383f4a0ec7 ARM: OMAP5+: Provide enable/disable_usb_clocks() for CONFIG_USB_XHCI_OMAP
CONFIG_USB_XHCI_OMAP is enabled for host mode independent of CONFIG_USB_DWC3
which is meant for gadget mode only. We need enable/disbale_usb_clocks() for
host mode as well so provide for it.

Fixes: 09cc14f4bc ("ARM: AM43xx: Add functions to enable and disable USB clocks"
Signed-off-by: Roger Quadros <rogerq@ti.com>
2016-06-02 21:42:14 -04:00
Peng Fan
9f8fa184fc imx: mx7: implement reset_misc
We need to power down lcdif to make 'reset' can pass stress test.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-05-31 17:42:31 +02:00
Lokesh Vutla
9b77b19178 ARM: OMAP4+: Fix DPLL programming sequence
All the output clock parameters of a DPLL needs to be programmed before
locking the DPLL. But it is being configured after locking the DPLL which
could potentially bypass DPLL. So fixing this sequence.

Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
2016-05-27 15:47:57 -04:00
Lokesh Vutla
3164f3c689 ARM: AM33xx: Add support for Clock Synthesizer
The CDCE913 and CDCEL913 devices are modular PLL-based, low cost,
high performance , programmable clock synthesizers. They generate
upto 3 output clocks from a single input frequency. Each output can
be programmed for any clock-frequency.

Adding support for the same.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:52 -04:00
Daniel Allred
1aad38f6e6 ARM: omap5: add hooks for cpu/SoC fdt fixups
Adds an fdt.c file in that defines the ft_cpu_setup() function,
which should be called from a board-specific ft_board_setup()).
This ft_cpu_setup() will currently do nothing for non-secure (GP)
devices	but contains pertinent updates for booting on secure (HS)
devices.

Update the omap5 Makefile to include the fdt.c in the build.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>

Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:37 -04:00
Daniel Allred
47c331ede1 ARM: omap-common: Add device type to CPU string
Update the CPU string output so that the device
type is now included as part of the CPU string that
is printed as the SPL or u-boot comes up. This update
adds a suffix of the form "-GP" or "-HS" for production
devices, so that general purpose (GP) and high security
(HS) can be distiguished. Applies to all OMAP5 variants.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>

Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:37 -04:00
Daniel Allred
410f525794 spl: build: ti: add support for secure boot images
Updates the SPL build so that when CONFIG_TI_SECURE_DEVICE
is in use (which it should be when building for secure parts),
the TI secure development package is used to create a valid
secure boot image. The u-boot SPL build processes is NOT aware
of the details of creating the boot image - all of that information
is encapsulated in the TI secure development package, which is
available from TI. More info can be found in README.ti-secure

Right now, two image types are generated, MLO and X-LOADER. The types
are important, as certain boot modes implemented by the device's ROM
boot loader require one or the other (they are not equivalent). The
output filenames are u-boot-spl_HS_MLO and u-boot-spl_HS_X-LOADER. The
u-boot-spl_HS_MLO image is also copied to a file named MLO, which is
the name that the device ROM bootloader requires for loading from the
FAT partition of an SD card (same as on non-secure devices).

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:36 -04:00
Daniel Allred
883dfd1553 ti: AM43xx: config.mk: Add support for generating secure boot images
Modifies the config.mk to build secure images when building
the SPL for secure devices.

Depending on the boot media, different images are needed
for secure devices. The build generates u-boot*_HS_* files
as appropriate for the different boot modes. The same u-boot
binary file is processed slightly differently to produce a
different boot image, depending on whether the user wants to
boot off SPI, QSPI or other boot media.

Refer to README.ti-secure for more information.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:34 -04:00
Daniel Allred
0a0c534b33 ti: omap-common: Add commands for generating secure SPL images
Adds a centralized config_secure.mk in omap-common for
OMAP-style TI secure devices to use for boot image generation

Depending on the boot media, different images are needed for
secure devices. These commands generates u-boot*_HS_* files that
need to be used to boot secure devices.

Please refer to README.ti-secure for more information.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:33 -04:00
Madan Srinivas
a774e08858 ti: omap-common: Add Kconfig file for secure device support
Defines CONFIG_TI_SECURE_DEVICE which needs to be turned on
when building images for secure devices. This flag is used
to invoke the secure image creation tools for creating a
boot image that can be used on secure devices. This flag
may also be used to conditionally compile code specific
to secure devices.

This terminology will be used by all OMAP architecture devices,
hence introducing to a common location.

With the creation of Kconfig for omap-common, moved the
sourcing of the Kconfig files for the omap3/4/5 and am33xx
devices from arch/arm/KConfig to the omap-common one.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:33 -04:00
Madan Srinivas
6384726d2d arm: Kconfig: Add support for AM43xx SoC specific Kconfig
Adding support for AM43xx secure devices require the addition
of some SOC specific config options like the amount of memory
used by public ROM and the address of the entry point of u-boot
or SPL, as seen by the ROM code, for the image to be built
correctly.

This mandates the addition of am AM43xx CONFIG option and the
ARM Kconfig file has been modified to source this SOC Kconfig
file. Moving the TARGET_AM43XX_EVM config option to the SOC
KConfig and out of the arch/arm/Kconfig.

Updating defconfigs to add the CONFIG_AM43XX=y statement and
removing the #define CONFIG_AM43XX from the header file.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>

Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:33 -04:00
Madan Srinivas
ce31ac7f72 arm: am33xx: Kconfig: Add secure device definitions
Adds a new Kconfig file for AM33xx class devices. We
need a common place to define CONFIG parameters
for these SOCs, especially for adding support
for secure devices.

a) Adds a definition for ISW_ENTRY_ADDR. This is the
address to which the ROM branches when the SOC
ROM hands off execution to the boot loader.
CONFIG_SYS_TEXT_BASE and CONFIG_SPL_TEXT_BASE are set
to this value for AM43xx devices.

b) Adds CONFIG_PUB_ROM_DATA_SIZE which is used to
calculate CONFIG_SPL_MAX_SIZE. This value indicates the
amount of memory needed by the ROM to store data during
the boot process.

Currently, these CONFIG options are used only by AM43xx,
but in future other AM33xx class SOCs will also use them.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:32 -04:00
Simon Glass
5c2dd4cd7a exynos: pwm: Add a driver for the exynos5 PWM
This driver supports the standard PWM API. There are 5 PWMs. Four are used
normally and the last is normally used as a timer.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2016-05-25 13:25:18 +09:00
Tom Rini
fc15b9beed Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-05-24 13:42:03 -04:00
Peng Fan
04cb3c0b0e imx: mx6: correct get_cpu_speed_grade_hz for i.MX6DQP
Correct get_cpu_speed_grade_hz for i.MX6DQP, otherwise we
will get wrong speed grade info i.MX6DQP.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-05-24 14:59:56 +02:00
Peng Fan
e4d79dcaa4 imx: mx6: ddr: support i.MX6D/QPlus
Support i.MX6D/QPlus.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-05-24 14:59:56 +02:00
Peng Fan
b949fd2ccb imx: mx6: use simpler runtime cpu dection macros
Use simpler runtime cpu dection macros.
i.MX6DL and i.MX6SOLO work the same, so use is_mx6sdl.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-05-24 14:59:56 +02:00
Peng Fan
dea572379e imx: mx6: support i.MX6SOLO when enable/disable_ldb_di_clock_sources
i.MX6DL and i.MX6SOLO work the same, add i.MX6SOLO support
when enable/disable_ldb_di_clock_sources.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-05-24 14:59:56 +02:00
Qianyu Gong
56747bfdbd armv7: ls102xa: spl: fix the macro name of MMC mode
MMCSD_MODE_FAT has been renamed to MMCSD_MODE_FS by commit 205b4f33.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:51:46 -07:00
Peng Fan
d15a244b05 imx: correct speed grading info for i.MX6UL
Correct speed grading info for i.MX6UL

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-05-18 09:47:41 +02:00
Stefan Agner
f716bf11f3 imx: imx7d: fix ahb clock mux 1
The clock parent of the AHB root clock when using mux option 1
is the SYS PLL 270MHz clock. This is specified in  Table 5-11
Clock Root Table of the i.MX 7Dual Applications Processor
Reference Manual.

While it could be a documentation error, the 270MHz parent is
also mentioned in the boot ROM configuration in Table 6-28: The
clock is by default at 135MHz due to a POST_PODF value of 1
(=> divider of 2).

Signed-off-by: Stefan Agner <stefan@agner.ch>
2016-05-17 17:52:20 +02:00
Russ Dill
b67d6b003c ARM: am33xx: Fix DDR initialization delays
The current delays in the DDR initialization routines for am33xx
architectures are sometimes not running long enough leading to DDR
init errors. On am437x, this shows up as an L3 NOC error after the
kernel boots. This is due to the timer not being initialized
properly, but instead still containing the timer init values from
the boot ROM which cause timers to expire in 1/4th the time
required.

timer_init is typically not called until board_init_r, however on
am33xx/am43xx udelay is required in sdram_init which is called
from board_init_f, so a call to timer_init is required earlier.

Note that this issue introduced in v2015.01 by:

b352dde "am33xx: Drop timer_init call from s_init".

Although this could instead fixed by reverting said commit, it
would cause timer_init to be called twice in both SPL and non-SPL
cases. This gives a little more fine grained control and also
matches what is being done on omap-command and fsl-layerscape.

Signed-off-by: Russ Dill <russ.dill@ti.com>
2016-05-06 10:10:20 -04:00
Tom Rini
821c89d38c Revert "omap3: Use raw SPL by default for mmc1"
Unfortunately with this change we now are unable to do FS mode boots
from MMC1 as with the way the code works today we will always load and
assume that the hard-coded raw location contains U-Boot.  Further, we
cannot fix this by just changing other logic to try FS-then-RAW as it
would also make us have to ignore what order the ROM is telling us to
try.

This reverts commit 22d90d560a.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-05-02 12:14:18 -04:00
Nishanth Menon
e52e334e5c ARM: DRA7: Add ABB setup for all domains
ABB should be initialized for all required domains voltage domain
for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If
we do not do this, kernel configuring just the frequency using the
default boot loader configured voltage can fail on many corner lot
units and has been hard to debug. This specifically is a concern with
DRA7 generation of SoCs since other than VDD_MPU, all other domains
are only permitted to setup the voltages to required OPP only at boot.

Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2016-04-25 15:10:41 -04:00
Nishanth Menon
a818097a33 ARM: OMAP5: Enable ABB configuration for MM voltage domain
Since we setup the voltage and frequency for the MM domain, we *must*
setup the ABB configuration needed for the domain as well. If we do not
do this, kernel configuring just the frequency using the default boot
loader configured voltage can fail on many corner lot units.

Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2016-04-25 15:10:40 -04:00
Nishanth Menon
3708e78c33 ARM: OMAP5/DRA7: Move ABB TXDONE mask to voltage structure
ABB TX_DONE mask will vary depending on ABB module. For example,
3630 never had ABB on IVA domain, while OMAP5 does use ABB on MM domain,
DRA7 has it on all domains with the exception of CORE, RTC.

Hence, move the txdone mask definition over to structure describing
voltage domain.

Signed-off-by: Nishanth Menon <nm@ti.com>
2016-04-25 15:10:39 -04:00
Nishanth Menon
2d9d057be6 ARM: OMAP5/DRA7: Get rid of control_std_fuse_opp_vdd_mpu_2
This information is already available under vcores->volts.efuse.reg.
There is no reason for duplicating the information since AVS Class 0
definitions are common for OMAP5 and DRA7 and defined with
STD_FUSE_OPP_* macros. This allows a central location of defining
the ABB and voltage definitions especially since they are reused.

This also makes it simpler to prevent mistakes involved when changing
the boot OPP for the device.

Signed-off-by: Nishanth Menon <nm@ti.com>
2016-04-25 15:10:38 -04:00
Fabio Estevam
69cc7dbf1f Add initial support for Technexion's PICO-IMX6UL-EMMC board
Add support for Technexion's PICO-IMX6UL-EMMC board.

For information about this board, please visit:
http://www.technexion.com/products/pico/pico-som/pico-imx6-emmc

Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-04-19 16:37:36 +02:00
Akshay Bhat
90d7cc42b3 imx: mx6: Fix procedure to switch the parent of LDB_DI_CLK
Due to incorrect placement of the clock gate cell in the ldb_di[x]_clk tree,
the glitchy parent mux of ldb_di[x]_clk can cause a glitch to enter the
ldb_di_ipu_div divider. If the divider gets locked up, no ldb_di[x]_clk is
generated, and the LVDS display will hang when the ipu_di_clk is sourced from
ldb_di_clk.

To fix the problem, both the new and current parent of the ldb_di_clk should
be disabled before the switch. This patch ensures that correct steps are
followed when ldb_di_clk parent is switched in the beginning of boot.

This patch was ported from the 3.10.17 NXP kernel
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/?h=imx_3.10.17_1.0.1_ga&id=eecbe9a52587cf9eec30132fb9b8a6761f3a1e6d

NXP errata number: ERR009219, EB821

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2016-04-19 16:05:12 +02:00
Tom Rini
814013253f Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-04-13 07:19:50 -04:00
Hans de Goede
df120142f3 arm: Replace v7_maint_dcache_all(ARMV7_DCACHE_INVAL_ALL) with asm code
Lets be consistent and also replace v7_maint_dcache_all()
with asm code for the invalidate case.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-11 20:48:27 -04:00
Hans de Goede
c09d29057a arm: Replace v7_maint_dcache_all(ARMV7_DCACHE_CLEAN_INVAL_ALL) with asm code
v7_maint_dcache_all() does not work reliable when build with gcc6,
see: https://bugzilla.redhat.com/show_bug.cgi?id=1318788

While debugging this I learned that v7_maint_dcache_all() is unreliable
when build with gcc5 too when it is marked as noinline.

This commit fixes the reliability issues by replacing the C-code with
the ready to use asm implementation from the kernel.

Given that this code when written as C-code clearly is quite fragile
(also see the existing comments about the C-code being the way it is
 to get optimal assembly) and that we have a proven asm alternative,
I believe that this is the best solution.

Note that we actually already had a copy of the kernel's
v7_flush_dcache_all() before this commit in
arch/arm/mach-uniphier/arm32/lowlevel_init.S.

This commit moves that code arch/arm/cpu/armv7/cache_v7_asm.S, renames
it to __v7_flush_dcache_all(), and adds a v7_flush_dcache_all() wrapper
which saves / restores the clobbered registers for use from C-code.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-11 20:48:26 -04:00
Paul Kocialkowski
41582e2e77 sniper: Change vendor name from lge to lg, matching devicetree vendor prefix
This moves the sniper board from the lge to lg, in order to match the devicetree
vendor prefix already defined in the kernel.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-04-01 17:18:06 -04:00
Alexander Graf
e6e505b93c sunxi: Move cpu independent code to mach directory
Some of the code in arch/arm/cpu/armv7/sunxi is actually armv7 specific, while
most of it is just generic code that could as well be used on an AArch64 SoC.

Move all files that are not really tied to armv7 into a new mach-sunxi
directory.

Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01 09:52:28 +02:00
Chen-Yu Tsai
0c935acb9e sunxi: usb_phy: Add support for A83T USB PHYs
The A83T has 3 USB PHYs: 1 for USB OTG, 1 for standard USB 1.1/2.0 host,
1 for USB HSIC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-31 17:04:06 +02:00
Hans de Goede
c74384c680 sunxi: Print soc-id from sram controller for sun8i boards
As the need for various magic sram pokes has shown this maybe useful
info to have. e.g. this shows one of my a23 tablets having an id of
1661 rather then the usual 1650 for the a23.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-31 14:26:52 +02:00
Hans de Goede
5f8afd704c sunxi: Add conditional magic sram poke for A33
I noticed that for certain SoC versions boot0 does a magic poke when
build for A33. I'm not aware of this actually being necessary anywhere,
but better safe then sorry.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-31 14:26:52 +02:00
Alexander Graf
d990f5c834 arm: Add support for HYP mode and LPAE page tables
We currently always modify the SVC versions of registers and only support
the short descriptor PTE format.

Some boards however (like the RPi2) run in HYP mode. There, we need to modify
the HYP version of system registers and HYP mode only supports the long
descriptor PTE format.

So this patch introduces support for both long descriptor PTEs and HYP mode
registers.

Signed-off-by: Alexander Graf <agraf@suse.de>
2016-03-27 09:12:17 -04:00
Nishanth Menon
c755e67516 ARM: OMAP5/DRA7: Expose do_set_iodelay
do_set_iodelay can now be used from board files based on needs of the
platforms variation they have.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:15 -04:00
Nishanth Menon
ceb7d77d6f ARM: OMAP5/DRA7: Split iodelay functionality into sub steps
Since many platforms may need different pad configuration required
depending on variation of the platform with minor deltas, it is
easier to maintain a sub step based approach to allow for pin mux
and iodelay configuration which may depend on the platform variations
and need to be done in IO isolation.

While we retain the older __recalibrate_iodelay function which provides
a ready sequencing, __recalibrate_iodelay_start and
__recalibrate_iodelay_end may be alternatively used now and the callers
will be responsible for the correct sequencing of operations.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:15 -04:00
Nishanth Menon
9c90f5135e ARM: DRA72: sdram: Update sdram ext phy configuration for SR2.0
Based on data from EMIF configuration tool 1.1.1.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:14 -04:00
Nishanth Menon
3d042e468a ARM: DRA7: hwdata: Update ioreg data for DRA72 SR2.0
Based on data from EMIF configuration tool 1.1.1. Expected update for
CTRL_WKUP_EMIF1_SDRAM_CONFIG_EXT in the next revision of the tool has
been incorporated as well.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:13 -04:00
Ravi Babu
d851ad3a66 ARM: DRA72x: Add support for detection of SR2.0
Add support for detection of SR2.0 version of DRA72x family of
processors.

Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:12 -04:00
Peng Fan
7abeec2234 imx: mx7d: move MX7D to Kconfig entry
If including MX7D in CONFIG_SYS_EXTRA_OPTIONS, CONFIG_ROM_UNIFIED_SECTIONS
 will not effect.So move MX7D to Kconfig entry from CONFIG_SYS_EXTRA_OPTIONS to
"select MX7D" to boards using i.MX7 Dual.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-03-26 14:16:12 +01:00
Peng Fan
9131c18cfa imx: mx6sx: move MX6SX to Kconfig entry
If including MX6SX in CONFIG_SYS_EXTRA_OPTIONS, CONFIG_ROM_UNIFIED_SECTIONS
will not effect.So move MX6SX to Kconfig entry from CONFIG_SYS_EXTRA_OPTIONS to
"select MX6SX" to boards using i.MX6 SoloX.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-03-26 14:16:12 +01:00
Stefan Roese
a7f480d92d arm: mx6: Add CCV xPress board support
This patch add support for the CCV xPress board which is equipped
with the i.MX6UL. And provides the following interfaces:

- 128MiB DDR
- UART
- I2C
- eMMC (with booting)
- Ethernet
- USB

This patch adds two build targets. One with and one without SPL. The
non-SPL version is used for loading U-Boot via USB (imx_usb_loader).

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-03-26 14:16:12 +01:00
Fabio Estevam
47173483a3 warp7: Add initial support
Add the basic support for Warp7 board.

For more information about this reference design, please visit:

https://www.element14.com/community/docs/DOC-79058/l/warp-7-the-next-generation-wearable-reference-platform

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2016-03-26 14:16:12 +01:00
Marek Vasut
b10d93ee9e arm: imx6: Switch DDR3 calibration to wait_for_bit()
Switch the DDR3 calibration from ad-hoc implementation of wait_for_bit()
to generic implementation of wait_for_bit().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-03-25 14:01:29 +01:00
Peng Fan
d78e7f2794 imx: print ARM clock for clocks command
Default print ARM clock for clocks command.
Test on i.MX6UL 14x14 evk board:
"
=> clocks
PLL_SYS         792 MHz
PLL_BUS         528 MHz
PLL_OTG         480 MHz
PLL_NET          50 MHz

ARM          396000 kHz
"

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-03-25 13:57:19 +01:00
Peng Fan
7082d87916 imx: mx6ul configure the PMIC_STBY_REQ pin as open drain
Configure the PMIC_STBY_REQ pin as open drain 100K according
to the design team's requirement for the PMIC_STBY_REQ pin
for i.MX 6UltraLite TO1.0.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-03-25 13:56:55 +01:00
Peng Fan
e4dc3fc068 imx: mx6ul: skip setting ahb rate
To i.MX6UL, default ARM rate and AHB rate is 396M and 198M,
no need to set them.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-03-25 13:56:40 +01:00
Ye Li
b777789ebd imx: mx6: Fix incorrect clear mmdc_ch0 handshake mask
Since the MX6UL/SL/SX only has one DDR channel, in CCM_CCDR register
the bit[17] for mmdc_ch0 is reserved and its proper state should be 1.
When clear this bit, the periph_clk_sel cannot be set and that
CDHIPR[periph_clk_sel_busy] handshake never clears.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2016-03-25 13:55:54 +01:00
vishnupatekar
e449e840c5 sunxi: A83T: fix 32bit overflow warning
In mctl_channel_init, (0x50<<26) which overflows 32bit.
It was supposed to be 0x50<<16,corrected now.

Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-23 22:04:13 +01:00
Hans de Goede
fc8991c61c sunxi: Fix gmac not working due to cpu_eth_init no longer being called
cpu_eth_init is no longer called for dm enabled eth drivers, this
was causing the sunxi gmac eth controller to no longer work in u-boot.

This commit fixes this by calling the clock, reset and pinmux setup
function from s_init() and enabling the phy power pin (if any) from
board_init().

The enabling of phy power cannot be done from s_init because it uses dm
and dm is not ready yet at this point.

Note that the mdelay is dropped as the phy gets enabled much earlier
now, so it is no longer needed.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Tested-by: Karsten Merker <merker@debian.org>
Tested-by: Michael Haas <haas@computerlinguist.org>
2016-03-23 22:04:13 +01:00
Hans de Goede
60fa63012f sunxi: Add support for USB vbus pin for USB3
The H3 has USB0 - USB3, add support for having a USB vbus pin for USB3.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Hans de Goede
1da598208d sunxi: Fix clock_twi_onoff for sun9i
Fix a copy and paste error which caused us to use the uart rather then
the twi reset bits in clock_twi_onoff for sun9i.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Hans de Goede
a93b0fe3fd sunxi: Fix clock_twi_onoff for sun8i-a83
clock_sun8i_a83.c did not contain a clock_twi_onoff implementation
at all, this is fixed by moving the clock_sun6i.c implementation,
which is correct for the a83 too, to a shared location.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Hans de Goede
730d2f3a41 sunxi: Fix clock_twi_onoff for sun6i
The clock_sun6i.c implementation was not deasserting the reset for
the regular i2c controllers, this commit fixes this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Hans de Goede
583fede8ee sunxi: A23: Fix some revisions needing a different magic sram poke
I've had this one a23 tablet which would not boot and I've finally
figured out what the problem is by looking at the released boot0 code,
it seems the magic sram controller poke which we need to do in s_init()
depends on the revision of the a23.

Specifically this change is needed to get the A23 SoC I have with the
following serial to boot: "E6071AB 26Y7".

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Stefano Babic
312a6c016a Merge branch 'next' 2016-03-20 22:04:29 +01:00
Tom Rini
f8a4826383 spl: arm: Make sure to include all of the u_boot_list entries
Starting with 96e5b03 we use a linker list for partition table
information.  However since we use this in SPL we need to make sure that
the SPL linker scripts include these as well.  While doing this, it's
best to simply include all linker lists to future proof ourselves.

Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-16 15:27:55 -04:00
Tom Rini
f5af0827f2 arm: omap-common: Guard some parts of the code with CONFIG_OMAP44XX/OMAP54XX
On OMAP4 platforms that also need to calculate their DDR settings we are
now getting very close to the linker limit size.  Since OMAP44XX is only
seen with LPDDR2, remove some run time tests for LPDDR2 or DDR3 as we
will know that we don't have it for OMAP44XX.

Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-16 15:03:48 -04:00
Paul Kocialkowski
69847dd8f0 omap4: Check warm reset for reboot mode validity
Since the SAR registers are filled with garbage on cold reset, this checks for a
warm reset to assert the validity of reboot mode.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:12:54 -04:00
Paul Kocialkowski
faec3f9841 omap4: Reboot mode support
Reboot mode is written to SAR memory before reboot in the form of a string.

This mechanism is supported on OMAP4 by various TI kernels.

It is up to each board to make use of this mechanism or not.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:12:53 -04:00