The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Signed-off-by: Tom Rini <trini@konsulko.com>
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly. Then, include
<linux/mtd/rawnand.h> where required directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS
In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last mx35 platform, remove that support as
well.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYVWWZgAKCRDKSWXLKUoM
IY3MAJ43Mlut5tK9gv45bp4HpyVOMuSvJwCfTiVr7ZxrBE8I8QC5+zHzBTmuM6g=
=aQtT
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.01-rc1
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
nand_dt_init() is still using fdtdec_xx() interface.
If OF_LIVE flag is enabled, dt property can't be get anymore.
Updating all fdtdec_xx() interface to ofnode_xx() to solve this issue.
For doing this, node parameter type must be ofnode.
First idea was to convert "node" parameter to ofnode type inside
nand_dt_init() using offset_to_ofnode(node). But offset_to_ofnode()
is not bijective, in case OF_LIVE flag is enabled, it performs an assert().
So, this leads to update nand_chip struct flash_node field from int to
ofnode and to update all nand_dt_init() callers.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Before e2e95e5e25 ("spi: Update speed/mode on change") most systems
silently defaulted to SF bus mode 0. Now the mode is always updated,
which causes breakage. It seems most SF which are used as boot media
operate in bus mode 0, so switch that as the default.
This should fix booting at least on Altera SoCFPGA, ST STM32, Xilinx
ZynqMP, NXP iMX and Rockchip SoCs, which recently ran into trouble
with mode 3. Marvell Kirkwood and Xilinx microblaze need to be checked
as those might need mode 3.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Cc: Andreas Biessmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Force the mtd name of spi-nor to "nor" + the driver sequence number:
"nor0", "nor1"... beginning after the existing nor devices.
This patch is coherent with existing "nand" and "spi-nand"
mtd device names.
When CFI MTD NOR device are supported, the spi-nor index is chosen after
the last CFI device defined by CONFIG_SYS_MAX_FLASH_BANKS.
When CONFIG_SYS_MAX_FLASH_BANKS_DETECT is activated, this config
is replaced by to cfi_flash_num_flash_banks in the include file
mtd/cfi_flash.h.
This generic name "nor%d" can be use to identify the mtd spi-nor device
without knowing the real device name or the DT path of the device,
used with API get_mtd_device_nm() and is used in mtdparts command.
This patch also avoids issue when the same NOR device is present 2 times,
for example on STM32MP15F-EV1:
STM32MP> mtd list
SF: Detected mx66l51235l with page size 256 Bytes, erase size 64 KiB, \
total 64 MiB
List of MTD devices:
* nand0
- type: NAND flash
- block size: 0x40000 bytes
- min I/O: 0x1000 bytes
- OOB size: 224 bytes
- OOB available: 118 bytes
- ECC strength: 8 bits
- ECC step size: 512 bytes
- bitflip threshold: 6 bits
- 0x000000000000-0x000040000000 : "nand0"
* mx66l51235l
- device: mx66l51235l@0
- parent: spi@58003000
- driver: jedec_spi_nor
- path: /soc/spi@58003000/mx66l51235l@0
- type: NOR flash
- block size: 0x10000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000004000000 : "mx66l51235l"
* mx66l51235l
- device: mx66l51235l@1
- parent: spi@58003000
- driver: jedec_spi_nor
- path: /soc/spi@58003000/mx66l51235l@1
- type: NOR flash
- block size: 0x10000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000004000000 : "mx66l51235l"
The same mtd name "mx66l51235l" identify the 2 instances
mx66l51235l@0 and mx66l51235l@1.
This patch fixes a ST32CubeProgrammer / stm32prog command issue
with nor0 target on STM32MP157C-EV1 board introduced by
commit b7f060565e ("mtd: spi-nor: allow registering multiple MTDs when
DM is enabled").
Fixes: b7f060565e ("mtd: spi-nor: allow registering multiple MTDs when DM is enabled")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
[trini: Add <dm/device.h> to <mtd.h> for DM_MAX_SEQ_STR]
Signed-off-by: Tom Rini <trini@konsulko.com>
nand_dt_init() is still using fdtdec_xx() interface.
If OF_LIVE flag is enabled, dt property can't be get anymore.
Updating all fdtdec_xx() interface to ofnode_xx() to solve this issue.
For doing this, node parameter type must be ofnode.
First idea was to convert "node" parameter to ofnode type inside
nand_dt_init() using offset_to_ofnode(node). But offset_to_ofnode()
is not bijective, in case OF_LIVE flag is enabled, it performs an assert().
So, this leads to update nand_chip struct flash_node field from int to
ofnode and to update all nand_dt_init() callers.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The COFNIG_KEYSTONE_RBL_NAND option is always enabled for the driver on
keystone platforms, but not older davinci platforms. Use def_bool for
the symbol. For CONFIG_KEYSTONE_NAND_MAX_RBL_PAGE, it's only used within
the driver and derived from another symbol, so remove CONFIG from the
name. Finally, CONFIG_KEYSTONE_NAND_MAX_RBL_SIZE is a bit more fixed.
For now, use the value directly. Long term, as part of DM'ifying NAND,
this should come from the device tree.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove the driver st_smic.c used in SPEAr products and the associated
config CONFIG_ST_SMI; this driver is no more used in U-Boot after the
commit 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr
support").
Fixes: 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver uses the CONFIG namespace to set the chips internal CONFIG
namespace related bits. However, CONFIG is reserved for the top-level
Kconfig based configuration system. Use CFG as the namespace here
instead to avoid pollution.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adds support for XT25F128B used on Odroid Go Advance. Unfortunately
this chip uses a continuation code which I cannot seem to parse, so
there are possibly going to be collisions with chips that use the same
manufacturer/ID.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The DM version CFI flash driver is in driver/mtd/cfi_flash.c, which
only gets built when FLASH_CFI_DRIVER is on. If CFI_FLASH is on but
FLASH_CFI_DRIVER is not, nothing is enabled at all.
Fix this dependency by selecting FLASH_CFI_DRIVER when CFI_FLASH is
enabled.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The DT bindings of "jedec,spi-nor" [1] defines "m25p,fast-read" property
to indicate that "fast read" opcode can be used to read data from the
chip instead of the usual "read" opcode.
If this property is not present in DT, mask out fast read in
spi_nor_init_params(). This change mirrors the same logic in
spi_nor_info_init_params() in drivers/mtd/spi-nor/core.c in
the Linux kernel v5.14-rc3.
[1] Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml in the kernel tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The smart spi_nor_adjust_hwcaps() does not respect the SPI flash's
hwcaps, and only looks to the controller on what can be supported.
The flash's hwcaps needs to be AND'ed before checking.
Fixes: 71025f013c ("mtd: spi-nor-core: Rework hwcaps selection")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This chip has been (briefly) tested on the MediaTek MT7688 based GARDENA
smart gateway.
Datasheet: http://xmcwh.com/Uploads/2020-12-17/XM25QH64C_Ver1.1.pdf
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The MX25V8035F is a 8Mb SPI NOR flash and the MX25R1635F is very
similar, but has twice the size (16Mb) and supports a wider supply
voltage range.
They were tested on the Kontron Electronics i.MX6UL and i.MX8MM SoMs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fixes mode clocks for SPINOR_OP_READ_FAST_4B in tiny.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The nor->ready() and spansion_sr_ready() introduced earlier in this
series are used for multi-die package parts.
The nor->quad_enable() sets the volatile QE bit on each die.
The nor->erase() is hooked if the device is not configured to uniform
sectors, assuming it has 32 x 4KB sectors overlaid on bottom address.
Other configurations, top and split, are not supported at this point.
Will submit additional patches to support it as needed.
The post_bfpt/sfdp() fixes the params wrongly advertised in SFDP.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cypress chips support SPINOR_OP_EN4B(B7h) to enable 4-byte addressing mode.
Cypress chips support B8h to disable 4-byte addressing mode instead of
SPINOR_OP_EX4B(E9h).
This patch defines new opcode and updates set_4byte() to support
enable/disable 4-byte addressing mode for Cypress chips.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The spansion_sr_ready() reads status register 1 by Read Any Register
commnad. This function is called from Flash specific hook with die address
and dummy cycles to support multi-die package parts from Spansion/Cypress.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
For dual/quad die package devices from Spansion/Cypress, the device's
status needs to be checked by reading status registers in all dies, by
using Read Any Register command. To support this, a Flash specific hook
that can overwrite the legacy status check is needed.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some of Spansion/Cypress chips support volatile version of configuration
registers and it is recommended to update volatile registers in the field
application due to a risk of the non-volatile registers corruption by
power interrupt. This patch adds a function to set Quad Enable bit in CFR1
volatile.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some of Spansion/Cypress chips support Read/Write Any Register commands.
These commands are mainly used to write volatile registers and access to
the registers in second and subsequent die for multi-die package parts.
The Read Any Register instruction (65h) is followed by register address
and dummy cycles, then the selected register byte is returned.
The Write Any Register instruction (71h) is followed by register address
and register byte to write.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Since this flash doesn't have a Profile 1.0 table, the Octal DTR
capabilities are enabled in the post SFDP fixup, along with the 8D-8D-8D
fast read settings.
Enable Octal DTR mode with 20 dummy cycles to allow running at the
maximum supported frequency of 200Mhz.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Cypress Semper flash is an xSPI compliant octal DTR flash. Add
support for using it in octal DTR mode.
The flash by default boots in a hybrid sector mode. Switch to uniform
sector mode on boot. Use the default 20 dummy cycles for a read fast
command.
The SFDP programming on some older versions of the flash was incorrect.
Fixes for that are included in the fixup hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some of Spansion/Cypress chips have overlaid 4KB sectors at top and/or
bottom, depending on the device configuration, while U-Boot supports
uniform sector layout only.
The spansion_erase_non_uniform() erases overlaid 4KB sectors,
non-overlaid portion of normal sector, and remaining normal sectors, by
selecting correct erase command and size based on the address to erase
and size of overlaid portion in parameters. Since different Spansion
flashes can use different opcode for erasing the 4K sectors, the opcode
must be passed in as a parameter based on the flash being used.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
[p.yadav@ti.com: Refactor the function to be compatible with nor->erase,
make 4K opcode customizable, call spi_nor_setup_op() before executing
the op.]
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
On devices with non-uniform sector sizes like Spansion S25 or S28 family
of flashes the sector under erase does not necessarily have to be
mtd->erasesize bytes long. For example, on S28 flashes the first 128 KiB
region is composed of 32 4 KiB sectors, then a 128 KiB sector, and then
256 KiB sectors till the end.
Let the flash-specific erase functions erase less than the requested
length in case of the 4 or 128 KiB sectors and report the number of
bytes erased back to the calling function.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
