Read the strobe select value from the device tree property ti,strobe-sel,
required for HS400 speed mode
Fixes: a20008eabd ("mmc: am654_sdhci: Add Support for configuring PHY in J721e")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210525093826.10390-2-a-govindraju@ti.com
CONFIG_SYSRESET_CMD_POWEROFF defines do_poweroff() in sysreset-uclass.c
that's why don't define it twice when both CONFIG_SYSRESET_CMD_POWEROFF and
CONFIG_CMD_POWEROFF are enabled. CONFIG_SYSRESET_CMD_POWEROFF depends on
CONFIG_CMD_POWEROFF.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for xilinx multirate(MRMAC) ethernet driver.
This driver uses multichannel DMA(MCDMA) for data transfers of MRMAC.
Added support for 4 ports of MRMAC for speeds 10G and 25G.
MCDMA supports upto 16 channels but in this driver we have setup only
one channel which is enough.
Tested 10G and 25G on all 4 ports.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
lpd_lsbus is clock which is used by many IPs like dmas, gems, gpio, sdhcis,
spis, ttcs, uarts, watchdog that's why make sense to also enable access to
change this clock. For this clock you already get the rate.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All these variables/structure are local and should be static.
Issues are reported by sparse:
drivers/mmc/zynq_sdhci.c:49:11: warning: symbol 'zynqmp_iclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:50:11: warning: symbol 'zynqmp_oclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:53:11: warning: symbol 'versal_iclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:54:11: warning: symbol 'versal_oclk_phases' was not declared. Should it be static?
drivers/mmc/zynq_sdhci.c:546:24: warning: symbol 'arasan_ops' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fix these kernel doc warnings:
drivers/mmc/zynq_sdhci.c:181: warning: contents before sections
drivers/mmc/zynq_sdhci.c:236: warning: contents before sections
drivers/mmc/zynq_sdhci.c:291: warning: contents before sections
drivers/mmc/zynq_sdhci.c:297: warning: Function parameter or member 'degrees' not described in 'sdhci_versal_sdcardclk_set_phase'
drivers/mmc/zynq_sdhci.c:354: warning: contents before sections
drivers/mmc/zynq_sdhci.c:360: warning: Function parameter or member 'degrees' not described in 'sdhci_versal_sampleclk_set_phase'
drivers/mmc/zynq_sdhci.c:467: warning: contents before sections
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Split arasan_zynqmp_set_tapdelay() to handle input and output tapdelays
separately. This is required to handle zero values for ITAP and OTAP
values. If we dont split, we will have to remove the if() in the
function, which makes ITAP values to be overwritten when OTAP values are
called to set and vice-versa.
Restrict tap_delay value calculated to max allowed 8 bits for ITAP and 6
bits for OTAP for ZynqMP.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Restrict tap_delay value to the allowed size(8bits for itap and 6 bits
for otap) before writing to the tap delay register.
Clear ITAP and OTAP delay bits before updating with the new tap value
for Versal platform.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Allow configuring ITAP and OTAP values with zero to avoid failures in
some cases (one of them is SD boot mode). Legacy, SDR12 modes require
to program the ITAP and OTAP values as zero, whereas for SDR50 and SDR104
modes ITAP value is zero.
In SD boot mode firmware configures the SD ITAP and OTAP values and
in this case u-boot has to re-configure required tap values(including zero)
based on the operating mode.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
set_phase() functions are not modifying the ret value and returning
the same uninitialized ret, return 0 instead.
Keep the return type as int to return errors when the tapdelay's are
set via xilinx_pm_request() in future.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Commit b81406db51 ("arm: serial: Add debug UART capability to the
pl01x driver") add supports to use pl01x as a debug UART. However,
due to CONFIG_IS_ENABLED macro requires CONFIG_SPL_* prefix, the
_debug_uart_init() would not choose TYPE_PL011 in SPL build. This
patch fixes the bug by judging CONFIG_DEBUG_UART_PL011 explicitly.
Signed-off-by: Chen Baozi <chenbaozi@phytium.com.cn>
Reviewed-by: Simon Glass <sjg@chromium.org>
pl01x_putc() might return -EAGAIN if there was no space in FIFO. In that
case, high-level caller should wait until there is space and resend the
character.
Signed-off-by: Chen Baozi <chenbaozi@phytium.com.cn>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
For some reason, the DragonBoard 410c aborts autoboot immediately if
U-Boot is started without LK. It looks like it picks up a single broken
character via serial and therefore believes a key was pressed to abort
autoboot.
After some debugging, it seems like adding some delay after pinctrl
setup but before UART initialization fixes the issue. It's also worth
mentioning that unlike when booting from LK, the pinctrl setup is
actually necessary when booting U-Boot without LK since UART is broken
if the pinctrl line is removed.
I suspect that reconfiguring the pins might take some time to stabilize
and if the UART controller is enabled too quickly it will pick up some
random noise. Adding a few milliseconds of delay fixes the issue and
shouldn't have any other negative side effects.
3ms seems to be the minimum delay required in my tests, use 5ms instead
just to be sure.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.
Move the SMMU initialization code into board support
and call it from board_init().
Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
RTC devices could provide battery-backed memory that can be used for
storing the reboot mode magic value.
Add a new reboot-mode back-end that uses RTC to store the reboot-mode
magic value. The driver also supports both endianness modes.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A use case for controlling the boot mode is when the user wants
to control the device boot by pushing a button without needing to
go in user-space.
Add a new backed for reboot mode where GPIOs are used to control the
reboot-mode. The driver is able to scan a predefined list of GPIOs
and return the magic value. Having the modes associated with
the magic value generated based on the GPIO values, allows the
reboot mode uclass to select the proper mode.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A new driver uclass is created to handle the reboot mode control.
The new uclass driver is updating an environment variable with the
configured reboot mode. The mode is extracted from a map provided
at initialization time. The map contains a list of modes
and associated ids.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch add support for using NXP's pca8574 I2C IO expander, which
has only 8 IO lines.
After this change the .data member's information from struct udevice_id
are used to either sent one or two bytes.
Moreover, the '_le16' suffix from pcf8575_i2c_{write|read}_le16()
functions have been removed as now we also sent 8 bit data.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Those members are not used anymore as ones from gpio_dev_priv
structure (when DM_GPIO support is enabled) are used instead.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
This change ensures both U-Boot and OP-TEE see the same content
from shared memory when OP-TEE is invoked prior U-Boot relocation.
This change is required since U-Boot may execute with data cache off
while OP-TEE always enables cache on memory shared with U-Boot.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The result of dpio_close() is actually taken into account.
Signed-off-by: Cosmin-Florin Aluchenesei <aluchenesei.cosmin-florin@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Change the reg variable to not be unsigned so that we not get into an
unsigned compared against 0.
Signed-off-by: Cosmin-Florin Aluchenesei <aluchenesei.cosmin-florin@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Define LOG_CATEGORY to allow filtering with log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Define LOG_CATEGORY to allow filtering with log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a common empty ops: eqos_null_ops() to remove the duplicated empty
functions and reduce the driver size for stm32 and imx config.
This patch also aligns the prototype of ops 'eqos_stop_clks' with other
eqos ops by adding return value.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Use the generic ethernet phy which already manages the correct binding
for gpio reset, including the assert an deassert delays.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Since the commit commit 6a895d039b ("net: Update eQos driver and FEC
driver to use eth phy interfaces") the field phyaddr of driver private data
struct eqos_priv is no more used in eqos_start() for the phy_connect()
parameter.
Now this variable is only initialized in eqos_probe_resources_stm32()
it can be removed.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Bind any subnode with name beginning by mdio, mdio0 for example,
and not only the "mdio" as namei of subnode.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Replace debug trace and printf to log macros:
- debug() replaced by dev_dbg() when device is available, this macro
indicate the device name since commit ceb70bb870 ("dm: Print device
name in dev_xxx like Linux")
- printf() replaced by log_notice() to allow dispatch to log backends.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The gpio reset and the assert or deassert delay are defined in generic
binding of the ethernet phy in Linux:
Documentation/devicetree/bindings/net/ethernet-phy.yaml
reset-gpios:
maxItems: 1
description:
The GPIO phandle and specifier for the PHY reset signal.
reset-assert-us:
description:
Delay after the reset was asserted in microseconds. If this
property is missing the delay will be skipped.
reset-deassert-us:
description:
Delay after the reset was deasserted in microseconds. If
this property is missing the delay will be skipped.
See also U-Boot: doc/device-tree-bindings/net/phy.txt
This patch adds the parsing of this common DT properties in the
u-class "eth_phy_generic", used by default in the associated driver
"eth_phy_generic_drv"
This parsing function eth_phy_of_to_plat can be reused by other
ethernet phy drivers for this uclass UCLASS_ETH_PHY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use same type as eth_device->iobase and support addresses greater
than INT_MAX.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Fixed a defect of a null pointer being discovered by Coverity Scan:
CID 331544: Null pointer dereferences (REVERSE_INULL)
Null-checking "size" suggests that it may be null, but it has already been
dereferenced on all paths leading to the check.
Signed-off-by: Chen Guanqiao <chenguanqiao@kuaishou.com>
It is useful to be able to iterate over block devices. Typically there
are fixed and removable devices. For security reasons it is sometimes
useful to ignore removable devices since they are under user control.
Add iterators which support selecting the block-device type.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for reading devicetree flags for MMC devices. With this we
can distinguish between fixed and removable drives. Note that this
information is only available when the device is probed, not when it is
bound, since it is read in the of_to_plat() method. This could be changed
if needed later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Rather than calling directly into the sandbox SDL code, we can use the
normal U-Boot console handling for this feature. Update the code, to make
it more generic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to read this information from the EC. It is useful for
determining whether the battery has enough charge to boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Renesas R-Car Gen3 development kits contain board ID EEPROM.
This driver parses out the board ID and revision out of that
EEPROM and exports it e.g. for the board-info print on boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Sean Anderson <sean.anderson@seco.com>
Cc: Simon Glass <sjg@chromium.org>
- Enabled distro boot for all TI platforms.
- Cleanup for AM335x Guardian Board
- PRUSS rproc on AM65 platform.
- Add PMIC support for J7200
- Misc fixes for Nokia RX-51
# Conflicts:
# arch/arm/mach-omap2/am33xx/Kconfig
As the deadline for migration to DM_USB, when using a USB host
controller has now gone two years past the deadline, enforce migration.
This is done by:
- Ensuring that all host controller options (other than the very legacy
old MUSB ones) now select USB_HOST. USB_HOST now enforces DM_USB and
OF_CONTROL.
- Remove other parts of Kconfig logic that had platforms pick DM_USB.
- To keep Kconfig happy, have some select statements test for USB_HOST
as well.
- Re-order some Kconfig entries and menus so that we can cleanly pick
host or gadget roles. For the various HCD options that have platform
glue options, group them together and update dependencies in some
cases.
- As SPL_DM_USB is not required, on platforms that had not yet enabled
it, disable it.
Cc: Marek Vasut <marex@denx.de>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Samuel Holland <samuel@sholland.org>
Cc: FUKAUMI Naoki <naobsd@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is also the last in family remove the related
support as well.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver is currently only used on MIPS Malta boards.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver is currently only used on MIPS Malta boards.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On MIPS the DRAM start address respectively CONFIG_SYS_SDRAM_BASE
is still used as a virtual, CPU-mapped address instead of being used
as physical address. Converting all MIPS boards and generic MIPS code
to fix that is not trivial. Due to the approaching deadline for
PCI DM conversion, this workaround is required for MIPS boards with
PCI support until the CONFIG_SYS_SDRAM_BASE issue could be solved.
Add a compile-time option to let the PCI uclass core optionally map
the DRAM address to a physical address when adding the PCI region
of type PCI_REGION_SYS_MEMORY.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
According to i.MX7ULP Reference Manual we should wait for WDOG unlock
and reconfiguration to complete.
Section "59.5.3 Configure Watchdog" provides the following example:
DisableInterrupts; //disable global interrupt
WDOG_CNT = 0xD928C520; //unlock watchdog
while(WDOG_CS[ULK]==0); //wait until registers are unlocked
WDOG_TOVAL = 256; //set timeout value
WDOG_CS = WDOG_CS_EN(1) | WDOG_CS_CLK(1) | WDOG_CS_INT(1) |
WDOG_CS_WIN(0) | WDOG_CS_UPDATE(1);
while(WDOG_CS[RCS]==0); //wait until new configuration takes effect
EnableInterrupts; //enable global interrupt
Update U-Boot WDOG driver to align with i.MX7ULP reference manual.
Use 32 bits accessing to CS register. According to RM, the bits in
this register only can write once after unlock. So using 8 bits access
will cause problem.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to i.MX7ULP Reference Manual the second word write for both
UNLOCK and REFRESH operations must occur in maximum 16 bus clock.
The current code is using writel() function which has a DMB barrier to
order the memory access. The DMB between two words write may introduce
some delay in certain circumstance, causing a WDOG timeout due to 16 bus
clock window requirement.
Replace writel() function by __raw_writel() to achieve a faster memory
access and avoid such issue.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Add the USB PHY driver for i.MX8MQ to work with DWC3 USB controller.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Patrick Wildt <patrick@blueri.se>
There is no separate SPL/TPL config for WATCHDOG_AUTOSTART.
So use IS_ENABLED instead of CONFIG_IS_ENABLED to make watchdog
working in SPL again.
Fixes: 830d29ac37 ("watchdog: Allow to use CONFIG_WDT without starting watchdog")
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Stefan Roese <sr@denx.de>
In uboot command line environment, watchdog is not able to be
stopped with below commands:
SOCFPGA_STRATIX10 # wdt dev watchdog@ffd00200
SOCFPGA_STRATIX10 # wdt stop
Refer to watchdog driver in linux kernel, it is also need to reset
watchdog after disable it so that the disable action takes effect.
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Add the support of SYSCFG clock used by syscon driver
to prepare the clock management of STM32MP_SYSCON_SYSCFG.
This clock is already defined in kernel device tree,
stm32mp151.dtsi but not yet supported in the syscon driver:
syscfg: syscon@50020000 {
compatible = "st,stm32mp157-syscfg", "syscon";
reg = <0x50020000 0x400>;
clocks = <&rcc SYSCFG>;
};
It is safe to support this clock in U-Boot driver with
RCC_MC_APB3ENSETR, Bit 11 SYSCFGEN: SYSCFG peripheral clocks
enable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Fix wrong register use when set/reset ST bit.
ST bit is in register M41T62_REG_SEC not in M41T62_REG_ALARM_HOUR.
I have not actually tested this. But this seemed buggy from inspection.
Fixes: 9bbe210512 ("rtc: m41t62: add oscillator fail bit reset support")
Signed-off-by: Max Yang <max.yang@deltaww.com>
When the default clocks cannot be set, the clock is silently probed and
the error is ignored. This is incorrect, since having the clocks at the
correct speed may be important for operation of the system.
Fix it by checking the return code.
Signed-off-by: Simon Glass <sjg@chromium.org>
The width is set up in single_of_to_plat() and can only have three values,
all of which result in a non-zero divisor. Add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Coverity (CID: 331154)
At present the return value of ofnode_get_property() is not checked, which
causes a coverity warning. While we are here, use logging for the errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Coverity (CID: 331157)
Update dm_dump_drivers() to use the return value from uclass_get() to
check the validity of uc. This is equivalent and should be more attractive
to Coverity.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Coverity (CID: 316601)
The devres_alloc() function is intended to avoid the need for freeing
memory, although in practice it may not be enabled, thus leading to a true
leak.
Nevertheless this is intended. Add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Coverity (CID: 312951)
The devres_alloc() function is intended to avoid the need for freeing
memory, although in practice it may not be enabled, thus leading to a true
leak.
Nevertheless this is intended. Add a comment to explain this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Coverity (CID: 312952)
This cannot actually fail, but check the value anyway to keep coverity
happy.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Coverity (CID: 316351)
At present if ifname is exactly IFNAMSIZ characters then it will result
in an unterminated string. Fix this by using strlcpy() instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Coverity (CID: 316358)
Acked-by: Ramon Fried <rfried.dev@gmail.com>
TI J7200 EVM has lp876441 pmic that is similar to tps65941. Add support
for same with existing driver with new compatible.
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210714205300.17424-2-g-tammana@ti.com
The K3 AM65x family of SoCs have the next generation of the PRU-ICSS
processor subsystem, commonly referred to as ICSSG. Each ICSSG processor
subsystem on AM65x SR1.0 contains two primary PRU cores and two new
auxiliary PRU cores called RTUs. The AM65x SR2.0 SoCs have a revised
ICSSG IP that is based off the subsequent IP revision used on J721E
SoCs. This IP instance has two new custom auxiliary PRU cores called
Transmit PRUs (Tx_PRUs) in addition to the existing PRUs and RTUs.
Each RTU and Tx_PRU cores have their own dedicated IRAM (smaller than
a PRU), Control and debug feature sets, but is different in terms of
sub-modules integrated around it and does not have the full capabilities
associated with a PRU core. The RTU core is typically used to aid a
PRU core in accelerating data transfers, while the Tx_PRU cores is
normally used to control the TX L2 FIFO if enabled in Ethernet
applications. Both can also be used to run independent applications.
The RTU and Tx_PRU cores though share the same Data RAMs as the PRU
cores, so the memories have to be partitioned carefully between different
applications. The new cores also support a new sub-module called Task
Manager to support two different context thread executions.
The driver currently supports the AM65xx SoC
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210622063431.3151-3-lokeshvutla@ti.com
The Programmable Real-Time Unit - Industrial Communication
Subsystem (PRU-ICSS) is present of various TI SoCs such as
AM335x or AM437x or the AM654x family. Each SoC can have
one or more PRUSS instances that may or may not be identical.
The PRUSS consists of dual 32-bit RISC cores called the
Programmable Real-Time Units (PRUs), some shared, data and
instruction memories, some internal peripheral modules, and
an interrupt controller. The programmable nature of the PRUs
provide flexibility to implement custom peripheral interfaces,
fast real-time responses, or specialized data handling.
Add support for pruss driver. Currently am654x family
is supported.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210622063431.3151-2-lokeshvutla@ti.com
RTC second scratch register[32-bit]:
-zero byte hold boot count value
-first byte hold update available state
-second byte hold version
-third byte hold magic number
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210611161350.2141-17-Gireesh.Hiremath@in.bosch.com
Gbp-Pq: Topic apertis/guardian
Gbp-Pq: Name am335x-guardian-software-update-available-status-is-store.patch
These headers are not actually used. Drop them so that this driver can
be used by other boards, e.g. coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When booting from coreboot we may not have a PCH driver available. The
SPI driver can operate without the PCH but currently complains in this
case. Update it to continue to work normally. The only missing feature
is memory-mapping of SPI-flash contents, which is not essential.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
At present only bridge devices are bound before relocation, to save space
in pre-relocation memory. In some cases we do actually want to bind a
device, e.g. because it provides the console UART. Add a devicetree
binding to support this.
Use the PCI_VENDEV() macro to encode the cell value. This is present in
U-Boot but not used, so move it to the binding header-file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These functions don't modify the device-ID struct that is passed in, so
mark the argument as const, so the data structure can be declared that
way. This allows it to be placed in the rodata section.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new 'quiet' argument to mmc_get_op_cond() function which avoids
printing error message when SD/eMMC card is not detected.
Espressobin and mx6cuboxi boards use this function for detecting presence
of eMMC and therefore it is expected and normal that eMMC does not have to
be connected. So error message "Card did not respond to voltage select!"
should be skipped in this case as it is not an error.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
The config option CONFIG_DEBUG_UART_CLOCK is not used by Armada 3720's
serial driver (it wasn't even before the recent update of that driver).
Even if it was used, the value was incorrect (the frequency of the clock
is 25 MHz, not 25.8048 MHz).
Remove it from config files and set the default value to 0.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Pali Rohár <pali@kernel.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Remapped address of PCIe outbound window may have set only bits from the
mask. Add additional check that remapped address which is calculated from
PCIe bus address specified in DTS file is valid.
Remove also useless clearing of low 16 bits in win_mask. As win_size is
power of two and is at least 0x10000 it means that it always has zero low
16 bits.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Function rtc_to_tm() is needed for FAT file system support even if we don't
have a real time clock. So move it from drivers/ to lib/.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The ST-Ericsson DB8500 SoC contains a MUSB OTG controller which
supports both host and gadget mode. For some reason there is
nothing special about it - add a simple glue driver for Ux500
that literally just sets up MUSB together with a generic PHY.
There are no SoC-specific registers etc needed to make USB work.
The new Ux500 glue driver is only tested to work with DM_USB
and DM_USB_GADGET. Both host and gadget mode work fine on
the u8500 "stemmy" board that is already present in U-Boot.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
The AB8500 PMIC contains an USB PHY that needs to be set up in
device or host mode to make USB work properly. Add a simple driver
for the generic PHY uclass that allows enabling it.
The if (CONFIG_IS_ENABLED(USB_MUSB_HOST)) might be a bit strange.
The USB PHY must be configured in either host or device mode and
somehow the USB PHY driver must be made aware of the mode.
Actually, the MUSB driver used together with this PHY does not
support dynamic selection of host/device mode in U-Boot at the moment.
Therefore, one very simple approach that works fine is to select
the mode to configure at compile time. When the MUSB driver is
configured in host mode the PHY is configured in host mode, and
similarly when the MUSB driver is configured in device/gadget mode.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
All devices based on ST-Ericsson Ux500 use a PMIC similar to AB8500
(Analog Baseband). There is AB8500, AB8505, AB9540 and AB8540
although in practice only AB8500 and AB8505 are relevant since the
platforms with AB9540 and AB8540 were cancelled and never used in
production.
In general, the AB8500 PMIC uses I2C as control interface, where the
different register banks are represented as separate I2C devices.
However, in practice AB8500 is always connected to a special I2C bus
on the DB8500 SoC that is controlled by the power/reset/clock
management unit (PRCMU) firmware.
Add a simple driver that allows reading/writing registers of the
AB8500 PMIC. The driver directly accesses registers from the PRCMU
parent device (represented by syscon in U-Boot). Abstracting it
further (e.g. with the i2c uclass) would not provide any advantage
because the PRCMU I2C bus is always just connected to AB8500 and
vice-versa.
The ab8500.h header is mostly taken as-is from Linux (with some
minor adjustments) to allow using similar code in both Linux and
U-Boot.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Add PCIe driver for UniPhier SoCs. This PCIe controller is based on
Synopsys DesignWare Core IP.
This version doesn't apply common DW functions because supported
controller doesn't have unroll version of iATU.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Linux kernel binding is using atmel,24c01 compatible string. On the
other hand there is atmel,24c01a which is not listed in the kernel.
Add compatible string without "a" suffix to be compatible with Linux
kernel binding.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Simplify the code a bit by using dev_read_addr_ptr() instead of
dev_read_addr(). This avoids having to cast explicitly to the
struct nomadik_mtu_regs.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Nomadik GPIO is a fairly simple GPIO module used in the ST-Ericsson
Ux500 SoCs (and some older Nomadik SoCs). It uses registers where
each GPIO is represented as a single bit, plus "set" and "clear"
registers that allow updating the state without having to read the
existing state.
The driver implements support for it for use together with DM_GPIO
and the existing ste-dbx5x0.dtsi device tree.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The original U-Boot port for the ST-Ericsson U8500 SoC was dropped
in commit 68282f55b8 ("arm: Remove unused ST-Ericsson u8500 arch").
Most of the drivers related to the old port were removed, but the
db8500_gpio.c driver was forgotten for some reason. There is no way
to select it and it does not compile anymore because of missing
headers, so let's just remove it.
The new port for U8500 introduced in commit 689088f9da
("arm: Add support for ST-Ericsson U8500 SoC") fully embraces the
new Driver Model and device trees where possible, so this is
preparation to add a new, simplified GPIO driver based on DM_GPIO.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The Microchip KSZ9477/KSZ9897/KSZ9567 7-Port Gigabit Ethernet Switches
support SGMII/RGMII/MII/RMII with register access via SPI, I2C, or MDIO.
This driver currently supports I2C register access but SPI or MDIO register
access can be easily added at a later time.
Tagging is not implemented and instead the active port is tracked to
avoid needing a tag to store port information.
This was tested with the imx8mm-venice-gw7901 board which has a
KSZ9897S switch with an IMX8MM FEC MAC master connected via RGMII_ID.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Enabling promiscuous mode is necessary if FEC is the master of a DSA
switch driver where each port has their own MAC address.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If the FEC is connected to a fixed-link (upstream switch port for
example) the phy_of_node should be set to the fixed-link node
so that speed and other properties can be found properly.
In addition fix a typo in the debug string.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
When using uclass_get_device* to get the FEC device we need to use
device sequence instead of index into UCLASS_ETH. In systems where for
example a I2C based DSA switch exists it will probe before the FEC
master and its ports will be registered first and have the first
indexes yet the FEC's sequence comes from the device-tree alias.
Take for example the imx8mm-venice-gw7901 board which has an i2c based
DSA switch:
u-boot=> net list
eth1 : lan1 00:0d:8d:aa:00:2f
eth2 : lan2 00:0d:8d:aa:00:30
eth3 : lan3 00:0d:8d:aa:00:31
eth4 : lan4 00:0d:8d:aa:00:32
eth0 : ethernet@30be0000 00:0d:8d:aa:00:2e active
Thus in this case uclass_get_device(UCLASS_ETH, 0, &dev) returns lan1
which is wrong but uclass_get_device_seq(UCLASS_ETH, 0, &dev) returns
ethernet@30be000 which is correct.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The driver depends on DM_SPI and if it's not available (e. g. in SPL),
then we should not try to build it as this will fail.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
If reset-gpio is defined by device-tree use that if
CONFIG_PCIE_IMX_PERST_GPIO is not defined.
Note that after this the following boards which define
CONFIG_PCIE_IMX_PERST_GPIO in their board header file as well as their
device-tree should be able to remove CONFIG_PCIE_IMX_PERST_GPIO without
consequence:
- mx6sabresd
- mx6sxsabresd
- novena
- tbs2910
- vining_2000
Note that the ge_bx50v3 board uses CONFIG_PCIE_IMX_PERST_GPIO and does
not have reset-gpios defined it it's pcie node in the dt thus removing
CONFIG_PCIE_IMX_PERST_GPIO globally can't be done until that board adds
reset-gpios.
Cc: Ian Ray <ian.ray@ge.com> (maintainer:GE BX50V3 BOARD)
Cc: Sebastian Reichel <sebastian.reichel@collabora.com> (maintainer:GE BX50V3 BOARD)
Cc: Fabio Estevam <festevam@gmail.com> (maintainer:MX6SABRESD BOARD)
Cc: Marek Vasut <marex@denx.de> (maintainer:NOVENA BOARD)
Cc: Soeren Moch <smoch@web.de> (maintainer:TBS2910 BOARD)
Cc: Silvio Fricke <open-source@softing.de> (maintainer:VINING_2000 BOARD)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The MX25V8035F is a 8Mb SPI NOR flash and the MX25R1635F is very
similar, but has twice the size (16Mb) and supports a wider supply
voltage range.
They were tested on the Kontron Electronics i.MX6UL and i.MX8MM SoMs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Aside from the usual fixes and updates one visible change is the
MMC update, which fixes some lingering bugs and gives a decent speed
increase on some boards (9->19 MB/s on H6, 21->43 MB/s on A64 eMMC).
I am keeping an watchful eye on bug reports here, to spot any correctness
regressions.
Another change is finally the enablement of the first USB host port on
many boards without micro-USB (data) sockets, like the Pine64 family.
That doubles the number of usable USB ports from 1 to 2 on those boards.
Some smaller fixes, 4GB DRAM support (on the H616) and a new board (ZeroPi)
conclude this first round of changes.
Compile-tested for all 157 sunxi boards, boot-tested on Pine H64,
Pine64-LTS, OrangePi Zero 2 and BananaPi M2 Berry.
Summary:
- DT update for H3/H5/H6
- Enable first USB port on boards without micro-USB
- ZeroPi board support
- 4GB DRAM support for H616 boards
- MMC fixes and speed improvement
- some fixes
At the moment the Allwinner MMC driver parses the bus-width and
non-removable DT properties itself, in the probe() routine.
There is actually a generic function provided by the MMC framework doing
this job, also it parses more generic properties like broken-cd and
advanced transfer modes.
Drop our own code and call mmc_of_parse() instead, to get all new
features for free.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
To avoid the complexity of DMA operations (with chained descriptors), we
use repeated MMIO reads and writes to the SD_FIFO_REG, which allows us
to drain or fill the MMC data buffer FIFO very easily.
However those MMIO accesses are somewhat costly, so this limits our MMC
performance, to between 17 and 22 MB/s, but down to 9.5 MB/s on the H6
(partly due to the lower AHB1 frequency).
As it turns out we read the FIFO status register after *every* word we
read or write, which effectively doubles the number of MMIO accesses,
thus effectively more than halving our performance.
To avoid this overhead, we can make use of the FIFO level bits, which are
in the very same FIFO status registers.
So for a read request, we now can collect as many words as the FIFO
level originally indicated, and only then need to update the status
register.
We don't know for sure the size of the FIFO (and it seems to differ
across SoCs anyway), so writing is more fragile, which is why we still
use the old method for that. If we find a minimum FIFO size available on
all SoCs, we could use that, in a later optimisation.
This patch increases the eMMC read speed on a Pine64-LTS from about
22MB/s to 44 MB/s. SD card reads don't gain that much, but with 23 MB/s
we now reach the practical limit for 3.3V SD cards.
On the H6 we double our transfer speed, from 9.5 MB/s to 19.7 MB/s.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Newer SoCs have a self calibration feature, which avoids us writing hard
coded phase delay values into the controller.
Consolidate the code by avoiding unnecessary #ifdefs, and also enabling
the feature for all those newer SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Among the SoCs using the "new timing mode", only the A83T needs to
explicitly switch to that mode.
By just defining the symbol for that one odd A83T bit to 0 for any other
SoCs, we can always OR that in, and save the confusing nested #ifdefs.
Clean up the also confusing new_mode setting on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Most Allwinner SoCs which use the so called "new timing mode" in their
MMC controllers actually use the double-rate PLL6/PERIPH0 clock as their
parent input clock. This is interestingly enough compensated by a hidden
"by 2" post-divider in the mod clock, so the divider and actual output
rate stay the same.
Even though for the H6 and H616 (but only for them!) we use the doubled
input clock for the divider computation, we never accounted for the
implicit post-divider, so the clock was only half the speed on those SoCs.
This didn't really matter so far, as our slow MMIO routine limits the
transfer speed anyway, but we will fix this soon.
Clean up the code around that selection, to always use the normal PLL6
(PERIPH0(1x)) clock as an input. As the rate and divider are the same,
that makes no difference.
Explain the hardware differences in a comment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When enabling PHYS_64BIT on 32-bit platforms, we get two warnings about
pointer casts in sunxi_mmc.c. Those are related to MMIO addresses, which
are always below 1GB on all Allwinner SoCs, so there is no problem with
anything having more than 32 bits.
Add the proper casts to make it compile cleanly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The delay and bus-width setup are slightly different across the
Allwinner SoC generations, and we covered this so far with some
preprocessor conditionals.
Use the more readable IS_ENABLE() instead.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Recent Allwinner platforms (starting with the H3) only use the MUSB
controller for peripheral mode and use HCI for host mode. As a result,
extra steps need to be taken to properly route USB signals to one or
the other. More precisely, the following is required:
* Routing the pins to either HCI/MUSB (controlled by PHY);
* Enabling USB PHY passby in HCI mode (controlled by PMU).
The current code will enable passby for each PHY and reroute PHY0 to
MUSB, which is inconsistent and results in broken USB peripheral support.
Passby on PHY0 must only be enabled when we want to use HCI. Since
host/device mode detection is not available from the PHY code and
because U-Boot does not support changing the mode dynamically anyway,
we can just mux the controller to MUSB if it is enabled and mux it to
HCI otherwise.
This fixes USB peripheral support for platforms with PHY0 dual-route,
especially H3/H5 and V3s.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Unfortunately the UART driver in current Linux for Armada 3700 expects
UART's parent clock to be XTAL and calculats baudrate divisor according
to XTAL clock. Therefore we must switch back to XTAL clock before
booting kernel.
Implement .remove method for this driver with DM_FLAG_OS_PREPARE flag
set.
If current baudrate is unsuitable for XTAL clock then we do not change
anything. This can only happen if the user either configured unsupported
settings or knows what they are doing and has kernel patches which allow
usage of non-XTAL parent clock.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Using TBG clock as parent clock for UART allows us using higher
baudrates than 230400.
Turris MOX with external FT232RL USB-UART works fine up to 3 MBaud
(which is maximum for this USB-UART controller), while EspressoBIN with
integrated pl2303 USB-UART also works fine up to 6 MBaud.
Slower baudrates with TBG as a parent clock can be achieved by
increasing TBG dividers and oversampling divider. When using the slowest
TBG clock, minimal working baudrate is 300.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Setting DM_FLAG_PRE_RELOC for Armada 3720 clock drivers (TBG and
peripheral clocks) makes it possible for serial driver to retrieve clock
rates via clk API.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
UART parent clock is by default the platform's xtal clock, which is
25 MHz.
The value defined in the driver, though, is 25.8048 MHz. This is a hack
for the suboptimal divisor calculation
Divisor = UART clock / (16 * baudrate)
which does not use rounding division, resulting in a suboptimal value
for divisor if the correct parent clock rate was used.
Change the code for divisor calculation to round to closest value, i.e.
Divisor = Round(UART clock / (16 * baudrate))
and change the parent clock rate value to that returned by
get_ref_clk().
This makes A3720 UART stable at standard UART baudrates between 1800 and
230400.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
also the last SPEAR3XX platform, remove that symbol as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it.
This is also the last PL010_SERIAL using board, so remove those
references.
Cc: Sergey Kostanbaev <sergey.kostanbaev@fairwaves.ru>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_T4160 platform, remove that support as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. This is also the last
of the ARCH_MPC8641/MPC8610 platforms, so remove that support as well.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this includes
the last ARCH_MPC8572 platform, remove that as well.
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the only ARCH_T1023 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is the last of the mcf547x_8x family of boards,
remove that support as well.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
With gcc-11 we get a multiple errors here as the declarations for
mscc_pinctrl_ops and mscc_gpio_ops are missing an extern.
CC: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With gcc-11 we see:
drivers/ddr/marvell/a38x/ddr3_debug.c:672:47: error: argument 2 of type 'u32[5]' {aka 'unsigned int[5]'} with mismatched bound [-Werror=array-parameter=]
672 | int ddr3_tip_read_adll_value(u32 dev_num, u32 pup_values[MAX_INTERFACE_NUM * MAX_BUS_NUM],
| ~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/ddr/marvell/a38x/ddr3_training_ip_engine.h:10,
from drivers/ddr/marvell/a38x/ddr3_init.h:17,
from drivers/ddr/marvell/a38x/ddr3_debug.c:6:
drivers/ddr/marvell/a38x/ddr3_training_ip_flow.h:116:47: note: previously declared as 'u32[]' {aka 'unsigned int[]'}
And similar warnings. Correct these by updating the prototype. Remove
the prototype for ddr3_tip_read_pup_value as it is unused.
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmDkSkAcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyD24B/9t87hFqWovJvVAcoUT
JoTqFblplE4Sckssy0cQyR7sRpzuZEaakUeAxaLFecBN6Tn30YJEG3hNpEDCLEbA
hn/oiZ4hQ3JA9Yu2SHepQi0fLqdAjkQtMXy57o3Mk20GBLtPtpdItUHxg3iyeMSj
Ny1mm/KjL6ltmNeGfYfeqRf435Rm718DB94wCZTgS9woYe3Z5YRDNBPyL7u27hpY
2WiyvvU9EA12mjGYdEt5sCqnTQZFtHHlEWNHz4a3db6HkcPV7pfr+SpTNJjcFhIg
O7VN7yUTwnV0UGu5IXTWcZqFIqJkLPbPX5cvkSBnnaGge4e0K3Cw36Nv/EqCY8LX
gWfu
=Ru8k
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2021.10 cycle:
This small fixes set is dedicated to fixing the onewire subsystem for
the at91 boards which was broken since 2020.04.
- mpc8379erdb DM_USB, DM_PCI and DM_ETH support.
- Drop PCI support from the integrator family of boards
- Add synquacer support
- Assorted lpc32xx updates and improvements
- snapdragon (and related) fixes, Broadcom iproc update
At the moment, the U-Boot serial_msm driver does not initialize the
UART_DM_DMEN register with the required value. Usually this does not
cause any problems, because there is Qualcomm's LK bootloader running
before U-Boot which initializes the register with the correct value.
It's important that this register is initialized correctly, because
the U-Boot driver does not make use of the BAM/DMA or single character
mode functionality of the UART controller. A different bootloader
before U-Boot might initialize the register differently.
For example, on DragonBoard 410c U-Boot can also be installed to the
"aboot" partition (replacing LK entirely). In this case U-Boot is
loaded directly by SBL, which seems to use the single-character mode
for some reason. In single character mode there is always just one
char in the FIFO, instead of the 4 characters expected by
msm_serial_fetch(). It also causes issues with "earlycon" later in
the Linux kernel, which tries to output 4 chars at once,
but only the first char will be written.
This causes early UART log in Linux to be corrupted like this:
[ 00ano:ameoi .Q1B[ 00ac _idaM00080oo'ahani-lcle._20). 15NdNii 5 SPMSJ20:U2
[ 00rkoolmsamel
[ 00Fw ]elamletopsioble
[ 00ore
instead of
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd030]
[ 0.000000] Machine model: Qualcomm Technologies, Inc. APQ 8016 SBC
[ 0.000000] earlycon: msm_serial_dm0 at MMIO 0x00000000078b0000 (options '')
[ 0.000000] printk: bootconsole [msm_serial_dm0] enabled
Make sure to initialize UART_DM_DMEN correctly to fix this issue
when loading U-Boot directly after SBL (instead of through LK).
There is no functional difference when loading U-Boot through LK
since LK also initializes UART_DM_DMEN to 0x0. [1]
[1]: https://git.linaro.org/landing-teams/working/qualcomm/lk.git/tree/platform/msm_shared/uart_dm.c?h=dragonboard410c-LA.BR.1.2.7-03810-8x16.0-linaro3#n203
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Convert the CONFIG_SYS_I2C_LPC32XX configuration symbol from an include
directive to a Kconfig value.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the of_match/compatible string to the lpc32xx i2c driver so it works
correctly with device-tree.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
The lpc32xx driver was not obtaining the per-device base address correctly
from the device tree. Fix the FIXME in order to get the correct base address.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
This is a driver for the HSSPI SPI controller on SynQuacer SoC.
The HSSPI has command sequence mode (memory mapped) and
direct mode (FIFO access). The driver will operate it under
the direct mode. And before booting OS, it switch back to the
command sequence mode since that is compatible with default
EDK2 behavior.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Add ECAM based SynQuacer PCIe RC driver. This driver configures the
PCIe RC and filter out a ghost pcie config.
Since the Linux kernel expects "socionext,synquacer-pcie-ecam" device
is configured by firmware (EDK2), it doesn't re-configure in the kernel.
So as same as EDK2, U-Boot needs to configure it before boot the kernel.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Without this fix, scsi-scan will cause a synchronous abort
when accessing ops->scan.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds a limited pulse-width modulator to sandbox's Chromium OS
Embedded Controller emulation. The emulated PWM device supports multiple
channels but can only set a duty cycle for each, as the actual EC
doesn't expose any functionality or information other than that. Though
the EC supports specifying the PWM channel by its type (e.g. display
backlight, keyboard backlight), this is not implemented in the emulation
as nothing in U-Boot uses this type specification.
This emulated PWM device is then used to test the Chromium OS PWM driver
in sandbox. Adding the required device node to the sandbox test
device-tree unfortunately makes it the first PWM device, so this also
touches some other tests to make sure they still use the sandbox PWM.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Each _device_ belonging to a given uclass of course has its own ->ops,
of a type determined by and known to the uclass.
However, no instance of a uclass_driver seems to populate ->ops, and
the only reference to it in code is this relocation.
Moreover, it's not really clear what could sensibly be assigned; it
would have to be some "struct uclass_ops *" providing a set of methods
for the core to call on that particular uclass, but should the need
for that ever arise, it would be better to have a member of that
particular type instead of void*.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpio_request_by_name should be called with proper flags.
The 0 value flag is invalid, and causes bad initialization of the gpio.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This commit adds support to piton_mmc driver for OpenPiton-riscv64
This driver has many things set as preconfigured because the hardware
automatically configures most of the settings during startup.
Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com>
Signed-off-by: Jonathan Balkind <jbalkind@ucsb.edu>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Replace 'pciaux' with 'pcieaux', including name string and function
prefix. The old name string, 'pciaux', might cause an error if PCIe
driver is changed to use clk_get_by_name() with 'pcieaux' to get
clock.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Remove the define EQOS_DESCRIPTOR_ALIGN unused since the
commit 6f1e668d96 ("net: dwc_eth_qos: Pad descriptors to cacheline size")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Make sure that errors in the PHY driver .startup() method, such as no
link, are propagated and not ignored.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The RGMII spec supports optional in-band status reporting for the speed
and duplex negotiated on the copper side, and the ENETC driver enables
this feature by default.
However, this does not work when the PHY does not implement the in-band
reporting, or when there is a MAC-to-MAC connection described using a
fixed-link. In that case, it would be better to disable the feature in
the ENETC MAC and always force the speed and duplex to the values that
were negotiated and retrieved over MDIO once the autoneg is finished.
Since this works always, we just do it unconditionally and drop the
in-band code.
Note that because we need to wait for the autoneg to complete, we need
to move enetc_setup_mac_iface() after phy_startup() returns, and then
pass the phydev pointer all the way to enetc_init_rgmii().
The same considerations have led to a similar Linux driver patch as well:
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=c76a97218dcbb2cb7cec1404ace43ef96c87d874
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Given that even a fixed-link has an associated phy_device, there is no
reason to operate in a mode when dm_eth_phy_connect fails.
Remove the driver checks for a NULL priv->phy and just return -ENODEV
when that happens.
Copyright updated according to corporate requirements.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The SMC911x Ethernet MACs can be integrated using a 16 or 32-bit bus.
The driver needs to know about this choice, which is the reason for us
having a Kconfig symbol for that.
Now this bus width is already described using a devicetree property, and
since the driver is DM compliant and is using the DT now, we should query
this at runtime. We leave the Kconfig choice around, in case the DT is
missing this property.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The SMC911x Ethernet driver needs to know which accessor functions it
can use to access the MMIO registers. For that reason we have a Kconfig
choice between 16 and 32-bit bus width.
Since it's only those two options that we (and the Linux kernel)
support, and there does not seem to be any evidence of another bus
width anywhere, limit the Kconfig construct to a simple symbol.
This simplifies the code and allows a later rework to be much easier.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYN105QAKCRDKSWXLKUoM
IZiFAJ9CIiEpHiBbnAhA0VOMGoaXHGULywCdED/5dNgVtc1C7y4avzETbEyWzD4=
=CdMa
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.10
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
It is working in a way that only minimal timeout is setup to reach
expiration just right after it is setup.
Please make sure that PMUFW is compiled with ENABLE_EM flag.
On U-Boot prompt you can test it like:
ZynqMP> wdt dev watchdog@fd4d0000
ZynqMP> wdt list
watchdog@fd4d0000 (cdns_wdt)
ZynqMP> wdt dev
dev: watchdog@fd4d0000
ZynqMP> wdt expire
(And reset should happen here)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The spi_get_bus_and_cs() may be called on the same bus and chipselect
with different frequency or mode. This is valid usecase, but the code
fails to notify the controller of such a configuration change. Call
spi_set_speed_mode() in case bus frequency or bus mode changed to let
the controller update the configuration.
The problem can easily be triggered using the sspi command:
=> sspi 0:0@1000
=> sspi 0:0@2000
Without this patch, both transfers happen at 1000 Hz. With this patch,
the later transfer happens correctly at 2000 Hz.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Fixes mode clocks for SPINOR_OP_READ_FAST_4B in tiny.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The nor->ready() and spansion_sr_ready() introduced earlier in this
series are used for multi-die package parts.
The nor->quad_enable() sets the volatile QE bit on each die.
The nor->erase() is hooked if the device is not configured to uniform
sectors, assuming it has 32 x 4KB sectors overlaid on bottom address.
Other configurations, top and split, are not supported at this point.
Will submit additional patches to support it as needed.
The post_bfpt/sfdp() fixes the params wrongly advertised in SFDP.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cypress chips support SPINOR_OP_EN4B(B7h) to enable 4-byte addressing mode.
Cypress chips support B8h to disable 4-byte addressing mode instead of
SPINOR_OP_EX4B(E9h).
This patch defines new opcode and updates set_4byte() to support
enable/disable 4-byte addressing mode for Cypress chips.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The spansion_sr_ready() reads status register 1 by Read Any Register
commnad. This function is called from Flash specific hook with die address
and dummy cycles to support multi-die package parts from Spansion/Cypress.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
For dual/quad die package devices from Spansion/Cypress, the device's
status needs to be checked by reading status registers in all dies, by
using Read Any Register command. To support this, a Flash specific hook
that can overwrite the legacy status check is needed.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some of Spansion/Cypress chips support volatile version of configuration
registers and it is recommended to update volatile registers in the field
application due to a risk of the non-volatile registers corruption by
power interrupt. This patch adds a function to set Quad Enable bit in CFR1
volatile.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some of Spansion/Cypress chips support Read/Write Any Register commands.
These commands are mainly used to write volatile registers and access to
the registers in second and subsequent die for multi-die package parts.
The Read Any Register instruction (65h) is followed by register address
and dummy cycles, then the selected register byte is returned.
The Write Any Register instruction (71h) is followed by register address
and register byte to write.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for 10G/25G (XXV) high speed ethernet. This Makes use of
the exiting AXI DMA, similar to 1G.
Signed-off-by: Alessandro Temil <atemil@waymo.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are lot of accesses to priv data in of_to_plat(), which is incorrect.
Create a platform data structure and use it in of_to_plat(), then copy all
platform data to priv data in probe.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds serial parameters that include stop bit mode, parity mode,
and character length. Mark parity and space parity modes are not
supported.
At the moment, the only path to call setconfig directly is DM testing,
however, this affects the size of SPL for DM testing, so it doesn't
apply to SPL.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Both of these drivers are implemented with and without DM that's why more
symbols should be handled.
The most problematic one is enabling DEBUG_UART_PL011 based on
PL01X_SERIAL(DM based) because debug console has type selection based on
it.
enum pl01x_type type = CONFIG_IS_ENABLED(DEBUG_UART_PL011) ?
TYPE_PL011 : TYPE_PL010;
Without it pl01x_generic_setbrg() is configuring different registers.
Fixes: 4cc24aeaf4 ("serial: Add missing Kconfig dependencies for debug consoles")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since this flash doesn't have a Profile 1.0 table, the Octal DTR
capabilities are enabled in the post SFDP fixup, along with the 8D-8D-8D
fast read settings.
Enable Octal DTR mode with 20 dummy cycles to allow running at the
maximum supported frequency of 200Mhz.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Cypress Semper flash is an xSPI compliant octal DTR flash. Add
support for using it in octal DTR mode.
The flash by default boots in a hybrid sector mode. Switch to uniform
sector mode on boot. Use the default 20 dummy cycles for a read fast
command.
The SFDP programming on some older versions of the flash was incorrect.
Fixes for that are included in the fixup hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some of Spansion/Cypress chips have overlaid 4KB sectors at top and/or
bottom, depending on the device configuration, while U-Boot supports
uniform sector layout only.
The spansion_erase_non_uniform() erases overlaid 4KB sectors,
non-overlaid portion of normal sector, and remaining normal sectors, by
selecting correct erase command and size based on the address to erase
and size of overlaid portion in parameters. Since different Spansion
flashes can use different opcode for erasing the 4K sectors, the opcode
must be passed in as a parameter based on the flash being used.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
[p.yadav@ti.com: Refactor the function to be compatible with nor->erase,
make 4K opcode customizable, call spi_nor_setup_op() before executing
the op.]
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
On devices with non-uniform sector sizes like Spansion S25 or S28 family
of flashes the sector under erase does not necessarily have to be
mtd->erasesize bytes long. For example, on S28 flashes the first 128 KiB
region is composed of 32 4 KiB sectors, then a 128 KiB sector, and then
256 KiB sectors till the end.
Let the flash-specific erase functions erase less than the requested
length in case of the 4 or 128 KiB sectors and report the number of
bytes erased back to the calling function.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When the flash is handed to us in a stateful mode like 8D-8D-8D, it is
difficult to detect the mode the flash is in. One option is to read SFDP
in all modes and see which one gives the correct "SFDP" signature, but
not all flashes support SFDP in 8D-8D-8D mode.
Further, even if you detect the mode of the flash via SFDP, you still
have the problem of actually reading the ID. The Read ID command is not
standardized across flash vendors. Flashes can have different dummy
cycles needed for reading the ID. Some flashes even expect a 4-byte
dummy address with the Read ID command. All this information cannot be
obtained from the SFDP table.
So, perform a Software Reset sequence before reading the ID and
initializing the flash. A Soft Reset will bring back the flash in its
default protocol mode assuming no non-volatile configuration was set.
This will let us detect the flash even if ROM hands it to us in Octal
DTR mode.
To accommodate cases where there is more than one flash on a board, and
only one of them needs a soft reset, failure to reset is not made fatal,
and we still try to read ID if possible.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
On probe, the SPI NOR core will put a flash in 8D-8D-8D mode if it
supports it. But Linux as of now expects to get the flash in 1S-1S-1S
mode. Handing the flash to Linux in Octal DTR mode means the kernel will
fail to detect the flash.
So, we need to reset to Power-on-Reset (POR) state before handing off
the flash. A Software Reset command can be used to do this.
One limitation of the soft reset is that it will restore state from
non-volatile registers in some flashes. This means that if the flash was
set to 8D mode in a non-volatile configuration, a soft reset won't help.
This commit assumes that we don't set any non-volatile bits anywhere,
and the flash doesn't have any non-volatile Octal DTR mode
configuration.
Since spi-nor-tiny doesn't (and likely shouldn't) have
spi_nor_soft_reset(), add a dummy spi_nor_remove() for it that does
nothing.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
A Soft Reset sequence will return the flash to Power-on-Reset (POR)
state. It consists of two commands: Soft Reset Enable and Soft Reset.
Find out if the sequence is supported from BFPT DWORD 16.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Micron MT35XU512ABA flash does not support the quad enable bit. But
instead of programming the Quad Enable Require field to 000b ("Device
does not have a QE bit"), it is programmed to 111b ("Reserved").
While this is technically incorrect, it is not reason enough to abort
BFPT parsing. Instead, continue BFPT parsing assuming there is no quad
enable bit present.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Allow flashes to specify a hook to enable octal DTR mode. Use this hook
whenever possible to get optimal transfer speeds.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The xSPI Profile 1.0 table specifies how many dummy cycles and address
bytes are needed for the Read Status Register command in Octal DTR mode.
Use that information to send the correct Read SR command.
Some controllers might have trouble reading just 1 byte in DTR mode. So,
when we are in DTR mode read 2 bytes and discard the second. This shows
no side effects with the two flashes I tested: Micron mt35xu512aba and
Cypress s28hs512t.
Update Read FSR to mimic Read SR because they share the same
characteristics.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This table is indication that the flash is xSPI compliant and hence
supports octal DTR mode. Extract information like the fast read opcode,
the number of dummy cycles needed for a Read Status Register command,
and the number of address bytes needed for a Read Status Register
command.
The default dummy cycles for a fast octal DTR read are set to 20. Since
there is no simple way of determining the dummy cycles needed for the
fast read command, flashes that use a different value should update it
in their flash-specific hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Some devices in DTR mode expect an extra command byte called the
extension. The extension can either be same as the opcode, bitwise
inverse of the opcode, or another additional byte forming a 16-byte
opcode. Get the extension type from the BFPT. For now, only flashes with
"repeat" and "inverse" extensions are supported.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
JESD216 rev D makes BFPT 20 DWORDs. Update the BFPT size define to
reflect that.
The check for rev A or later compared the BFPT header length with the
maximum BFPT length, BFPT_DWORD_MAX. Since BFPT_DWORD_MAX was 16, and so
was the BFPT length for both rev A and B, this check worked fine. But
now, since BFPT_DWORD_MAX is 20, it means this check will also stop BFPT
parsing for rev A or B, since their length is 16.
So, instead check for BFPT_DWORD_MAX_JESD216 to stop BFPT parsing for
the first JESD216 version, and check for BFPT_DWORD_MAX_JESD216B for the
next two versions.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Double Transfer Rate (DTR) is SPI protocol in which data is transferred
on each clock edge as opposed to on each clock cycle. Make
framework-level changes to allow supporting flashes in DTR mode.
Right now, mixed DTR modes are not supported. So, for example a mode
like 4S-4D-4D will not work. All phases need to be either DTR or STR.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Even when spi_nor_write_reg() has no data to write, like when executing
a write enable operation, it sets the data direction to
SPI_MEM_DATA_OUT. This trips up spi_mem_check_buswidth() because it
expects a data phase when there is none. Make sure the data direction is
set to SPI_MEM_NO_DATA when there is no data to write.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The spi-mem layer provides a spi_mem_supports_op() function to check
whether a specific operation is supported by the controller or not.
This is much more accurate than the hwcaps selection logic based on
SPI_{RX,TX}_ flags.
Rework the hwcaps selection logic to use spi_mem_supports_op().
To make sure the build doesn't break for boards not using CONFIG_DM_SPI,
add a simple SPI_{RX,TX}_ based hwcaps selection logic in spi-mem-nodm
similar to spi_mem_default_supports_op(). This change is only
compile-tested.
To avoid SPL size problems on the x530 board, the old hwcaps selection
is still kept around. Leaving the code in-place was getting difficult to
read and understand, so the code is restructured to have it all in one
isolated function. As a result of this, the parameter hwcaps to
spi_nor_setup() is no longer needed. Remove it.
Based on the Linux commit c76f5089796a (mtd: spi-nor: Rework hwcaps
selection for the spi-mem case, 2019-08-06)
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sometimes the information in a flash's SFDP tables is wrong. Sometimes
some information just can't be expressed in the SFDP table. So,
introduce the fixup hooks to allow tailoring settings for a specific
flash.
Three hooks are added: default_init, post_sfdp, and post_bfpt. These
allow tweaking the flash settings at different point in the probe
sequence. Since the hooks reside in nor->info, set that value just
before the call to spi_nor_init_params().
The hooks and at what points they are executed mimics Linux's spi-nor
framework. One major difference is that Linux puts the struct
spi_nor_fixups in nor->info. This is not possible in U-Boot because the
spi-nor-ids list is shared between spi-nor-core.c and spi-nor-tiny.c.
Since spi-nor-tiny shouldn't have those fixup hooks populated, add a
separate function that lets flashes populate their fixup hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
These structures will be used in a later commit inside another structure
definition. Also take the declarations out of the ifdef since they won't
affect the final binary anyway and will be used in a later commit.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
