These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The deadline for migration to CONFIG_DM is v2020.01. The VCT
baords would need an almost complete rewrite of all drivers to
support driver model.
Unless someone has access to the hardware and volunteers to do the migration,
the board should be scheduled for removal.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Some drivers (clk, pinctrl, reset, ...) are necessary for reset of the
system, they should be always selected.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds default eth pinctrl for all boards.
There are two pinctrl nodes used for two scenarios:
ephy_iot_mode - for IOT boards which have only one port (PHY0)
ephy_router_mode - For routers which have more than one ports
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds default p0led status and phy0 link polling for all boards.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
All three UARTs of mt7628 are actually MediaTek's high-speed UARTs which
support baudrate up to 921600.
The high-speed UART is compatible with ns16550 when baudrate <= 115200.
Add compatible string to dtsi file so u-boot can use it when serial_mtk
driver is built in.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The UART of MT7628 has fixed 40MHz input clock so there is no need to put
clock-frequency in every dts files. Just put it into the common dtsi file.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
If configuration is set to skip low level init, automatic
probe of L2 cache size is not performed and the size is set to 0.
Flushing or invalidating the L2 cache will fail in this case.
Add a static configuration (SYS_DCACHE_LINE_SIZE) with default set to 0.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
With commit 06985289d4 ("watchdog: Implement generic watchdog_reset()
version") the init sequence has changed in arch_misc_init(), resulting
in a re-appearance of the d-cache issue on MT7688 boards (e.g. gardena).
When this happens, the first (or sometimes later ones as well) TFTP
command hangs and does not complete correctly. This leads to the
assumption that the d-cache is not in a clean state once the ethernet
driver is called (d-cache is used here for the buffers). The old work-
around with the cache flush somehow does not work any more now with
the new code change.
Unfortunately adding CONFIG_SYS_MALLOC_CLEAR_ON_INIT also did not fix
this issue. With v2019.07-rc3 it shows again. The time of accessing
the data seems to be very important here. It needs to be "very late"
in the boot process.
Testing has shown, that copying a 64KiB area in DDR at a very late
bootup time, directly before calling into the prompt, fixes this issue.
Flushing of the complete d-cache does not seem to necessary, as this
copy alone seems to fix this problem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With commit 06985289d4 ("watchdog: Implement generic watchdog_reset()
version") the init sequence has changed in arch_misc_init(), resulting
in a re-appearance of the d-cache issue on MT7688 boards (e.g. gardena).
When this happens, the first (or sometimes later ones as well) TFTP
command hangs and does not complete correctly. This leads to the
assumption that the d-cache is not in a clean state once the ethernet
driver is called (d-cache is used here for the buffers). The old work-
around with the cache flush somehow does not work any more now with
the new code change.
To fix this issue, this patch now removes the old workaround and selects
CONFIG_SYS_MALLOC_CLEAR_ON_INIT for ARCH_MTMIPS. With this option the
complete malloc area is initialized with zeros (cache lines are touched).
Testing has shown that this also fixes the issue on the MT7688 boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Update device tree for luton to add support for luton pcb90.
This pcb has 24 ports from which 12 ports are connected to
SerDes6G.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Currently mach-mt7620 contains only support for mt7628. To avoid confusion,
rename mach-mt7620 to mach-mtmips, which means MediaTek MIPS platforms.
MT7620 and MT7628 should be distinguished by SOC_MT7620 and SOC_MT7628
because they do not share the same lowlevel codes.
Dependencies of four drivers are changed to SOC_MT7628 as these drivers
are only used by MT7628.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Microsemi SoC defines CONFIG_SYS_SDRAM_BASE to be 0x80000000, which
represents the start of kseg0 and represents a virtual address. Meaning
that the initrd_start and initrd_end point somewhere kseg0.
When these parameters are passed to linux kernel through DT
they are pointing somewhere in kseg0 which is a virtual address but linux
kernel expects the addresses to be physical addresses(in kuseg) because
it is converting the physical address to a virtual one.
Therefore update the uboot to pass the physical address of initrd_start
and initrd_end by converting them using the function virt_to_phys before
setting up the DT.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Remove "select MSCC_BITBANG_SPI_GPIO" since Kbuild option was deleted
back in commit ace9c103df:
commit ace9c103df
Author: Lars Povlsen <lars.povlsen@microchip.com>
Date: Tue Jan 8 10:38:35 2019 +0100
mips: gpio: mscc: Obsoleted gpio-mscc-bitbang-spi.c
Add ethernet nodes for Serval SoCs family. There are 2 pcb in this
family: pcb105 and pcb106.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
In case the ddr training was failing, it couldn't reset, it was just
hanging. Therefore reimplement it, so when ddr training is failing
it would call _machine_restart, which power downs the DDR and does
a force reset.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
This patch tries to implement a generic watchdog_reset() function that
can be used by all boards that want to service the watchdog device in
U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG.
Without this approach, new boards or platforms needed to implement a
board specific version of this functionality, mostly copy'ing the same
code over and over again into their board or platforms code base.
With this new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
This patch also adds a new flag to the GD flags, to flag that the
watchdog is ready to use and adds the pointer to the watchdog device
to the GD. This enables us to remove the global "watchdog_dev"
variable, which was prone to cause problems because of its potentially
very early use in watchdog_reset(), even before the BSS is cleared.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Maxim Sloyko <maxims@google.com>
Cc: Erik van Luijk <evanluijk@interact.nl>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: "Álvaro Fernández Rojas" <noltari@gmail.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Add ethernet nodes for ServalT SoCs family. Currently there is only one
pcb(pcb116) in this family.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Add network driver for Microsemi Ethernet switch.
It is present on ServalT SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add ethernet nodes for Jaguar2 SoCs family. There are 3 pcb in this
family: pcb110, pcb111 and pcb112.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Enable the gpio controllers in the device tree
of the board bcm968380gerg.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add gpio controllers in bcm6838 device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
QCA9563 is CPU used on AP152 board :
Clock speed : 750 MHz ,
Arch : Mips 74Kc,
Eth : SGMII interface,
MIMO config : 3 * 3 450M,
2 * USB 2.0,
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Changes for v2:
- coding style cleanup
- remove ununsed flash chip in defconfig
- enable automatic icache / dcache size in defconfig
Changes for v3:
- add detailed information for qca956x in commit message
Changes for v4:
- remove pre-configured network settings in ap152.h
Changes for v5:
- coding style cleanup
See details in chapter 8.6.2 and 8.6.4 (page 140-141) of qca9563 datasheet,
NFRAC[17:0]
So the mask of [17:5] is 0x1fff not 0x3fff.
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Changes for v2-v3:
- add more information for this commit
Changes for v4-v5:
- coding style cleanup
Remove the function boot_reloc_ramdisk in the file arch/mips/lib/bootm
because it is relocating again the ramdisk. The function do_bootm_states()
already relocates the ramdisk even if it is a legacy uImage or a FIT image.
The relocation in the function do_bootm_states() was introduce in the
commit c2e7e72bb9 ("bootm: relocate ramdisk
if CONFIG_SYS_BOOT_RAMDISK_HIGH set")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch changes Gardena to the correct GARDENA spelling. Also the
platform name is "GARDENA smart Gateway". This patch changes the
incorrect occurrances.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
There is no reason not to use the Linux "jedec,spi-nor" binding in U-Boot
dts files. This compatible has been added in sf_probe, let use it.
This patch switches to jedec,spi-nor when spi-flash is used in the DTS
and DTSI files, and removed spi-flash when jedec,spi-nor is already
present.
The x86 dts are switched in a separate commit since it depends on a change
in fdtdec.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Evgeniy Paltsev <paltsev@synopsys.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Patrick Delaunay <Patrick.delaunay@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch moves all instances of static "watchdog_dev" declarations to
the "data" section. This may be needed, as the BSS may not be cleared
in the early U-Boot phase, where watchdog_reset() is already beeing
called. This may result in incorrect pointer access, as the check to
"!watchdog_dev" in watchdog_reset() may not be true and the function
may continue to run.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Since commit 27cb7300ff ("Ensure device tree DTS is compiled"),
build succeeds irrespective of the correctness of Makefile.
In fact, you can compile any defconfig without adding any entry in
arch/*/dts/Makefile.
I am going to revert that commit, so device tree must be explicitly
listed in Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than
CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the
same script for both SPL and TPL. Add logic to scripts/Makefile.spl to
pass in the right value when preprocessing the script.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add board support and configuration for Jaguar2 SoC family.
The detection of the board type is based on the phy ids.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
As Ocelot, Servalt, Luton and Jaguar2, this family of SoCs are
found in Microsemi Switches solution.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add board support, configuration and DTS for Servalt SoC
family. Currently there is one board in this family.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
As Ocelot, Luton and Jaguar2, this family of SoCs are found
in Microsemi Switches solution.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Set the correct power-up state (default-state) of the green power LED.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add board support and configuration for Jaguar2 SOC family.
The detection of the board type in this family is based on the phy ids.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
As the Ocelot and Luton SoCs, this family of SoCs are found
in Microsemi Switches solution.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Thes patch change the luton base device tree to use the newly added
SPI bitbang driver.
It also updates the "mscc_luton_defconfig" to use the new driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch add a new SPI driver for MSCC SOCs that does not sport the
designware SPI hardware controller.
Performance gain: 7.664 seconds vs. 17.633 for 1 Mbyte write.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
There is no real difference between the generic variant and
the custom variant except that the generic variant is more
optimised. This also saves 24 Bytes in the SPL binary.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@collabora.com>
Discard ABI related sections which are not required for debugging.
Rearrange debug sections similar to Linux. Remove the remaining
explicitely specified sections in the unused part because those
sections are not created anymore or because the linker puts them
by default at the end of the ELF binary.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@collabora.com>
This enables the use of the MSCC serial GPIO driver on the MSCC
VCoreIII 'ocelot' SOC, and add gpio-leds nodes to the pcb123 and
pcb120 DT.
Signed-off-by: Lars Povlsen <lars.povlsen@microsemi.com>
This enables the use of the MSCC serial GPIO driver, and add gpio-leds
nodes to the 'luton' pcb090 and pcb091 DT.
Signed-off-by: Lars Povlsen <lars.povlsen@microsemi.com>
As we are moving to multi-dtb and board detection, remove static board
config options, and introduce board probing instead.
Luton: This add single-binary support for the two MSCC luton-based
reference boards - pcb090 and pcb091. The SoC chip ID is used to
determine the board type.
Ocelot: This add single-binary support for the two MSCC ocelot-based
reference boards - pcb120 and pcb123. The PHY ids on specific ports
are used to determine the board type.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
This prepares individual device trees for MSCC luton-based reference
boards - pcb090 and pcb091.
Note: Even though the devices trees are quite common, they will differ
significantly in coming patches.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
The GPIO control function can be used for controlling alternate
functions associated with a GPIO.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Add support for the Creator CI20 platform based on the JZ4780 SoC.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add initial support for the Ingenic JZ47xx MIPS SoC.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add header with SPL boot mode and type definitions.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Adding the support for the Luton boards PCB91 which share common code with
the Ocelots boards, including board code, device tree and configuration.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This family of SoCs are found in the Microsemi Switches solution and have
already a support in the linux kernel.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This path add a new helper allowing to prefetch and lock instructions
into cache. This is useful very early in the boot when no RAM is
available yet.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Export create_tlb() as an inline function in mipsregs.h. It allows to
remove the declaration of the function from the board files.
Then it will allow also to use this function very early in the boot when
the stack is not usable.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
With moving write_on_tlb() to arch/mips/include/asm/mipsregs.h
there are now compiler warnings when some generic code includes
asm/io.h. This happens for example when enabling OF live tree.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
It has been noticed, that sometimes the d-cache is not in a
"clean-state" when U-Boot is running on MT7688. This was detected when
using the ethernet driver (which uses d-cache) and a TFTP command does
not complete. Flushing the complete d-cache (again?) here seems to fix
this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This fixes following DTC warning:
arch/mips/dts/nexys4ddr.dtb: Warning (compatible_is_string_list): /ethernet@10e00000/mdio/phy@1:compatible: property is not a string list
As upstream DTS in Linux doesn't have the offending property,
simply remove it to fix the warning.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Remove all interrupt nodes that cause warnings regarding a missing
interrupt parent. There are no interrupt controller nodes defined
and the device trees don't match the ones in Linux anymore.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
As the driver has been changed to be more specific, the DT compatible
property also needs to be adapted.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Commit 86f21c96f4 (mips: Use common _AC macro now.) removed the _AC
definition from const.h. All other macros defined in const.h are not
used anywhere, and there is now no user of this header. Remove this
header.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Drop the _AC and UL macros from common.h. Linux headers is the original
source of this macro, so keep its definition in the same header.
Update existing users of these macros to include const.h directly.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Rick Chen <rick@andestech.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Use the global MIPS specific u-boot.lds for linking standalone programs
instead of the outdated ones in examples/standalone/. Also pass --gc-sections
in LDFLAGS_STANDALONE to optimize the size of standalone programs.
Finally remove the deprecated config.mk files in arch/mips/cpu/mips[32,64]/.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Introduce a new Makefile variable for passing LDFLAGS to standalone
programs. Currently the variable CONFIG_STANDALONE_LOAD_ADDR is
misued on some archs to pass a specific linker script.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
These misc updates include the following changes:
- Change baudrate from 57600 to 115200
- Enable MIPS_BOOT_CMDLINE_LEGACY
- Enable FIT support
- Enable ethernet support
- Enable SPI support
- Enable GPIO support
- Change max image size from 0x40000 to 0x80000
A note about the baudrate change:
The original Mediatek U-Boot version used 57600 baud. Lets move to a
more common and faster speed of 115200 baud. And remove the "console="
property from the DT as its not needed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
These misc updates include the following changes:
- Change baudrate from 57600 to 115200
- Enable MIPS_BOOT_CMDLINE_LEGACY
- Enable FIT support
- Enable ethernet support
- Enable SPI NOR and NAND support
- Change MTD_UBI_BEB_LIMIT to 22
- Enable MTD Support
- Enable GPIO support
- Enable watchdog support
- Enable bootcounter support
- Enable version variable
- Change max image size from 0x80000 to 0xa0000
- Change SYS_MALLOC_LEN to 16MiB (because of UBI/UBIFS)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This is needed to set the LEDs automatically to a default state, as
configured in the dts.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add the available LEDs to the DTS file so that they can be used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch enables and starts the watchdog on the MT7620 platform.
Currently the WD timeout is configured to 60 seconds.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
[fixed build error due to missing function prototype arch_misc_init]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Imply DM_ETH and DM_GPIO for ARCH_MT7620, as this platform now supports
ethernet and GPIO as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This fixes an issue which has been noticed on the Gardena board, with
the watchdog enabled, where the watdchdog reset (after a system hang)
did result in reporting of 2.9 GiB and a hang after this. With this
patch applied the memory controller is correctly reset and initialized
again even after a watchdog reset.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
MIPS is the only architecture currently supported by U-Boot that does
not implement any of the in/out register access functions.
To have a interface that is useable across architectures, add the
functions to the MIPS architecture (implemented using the __raw_write
and __raw_read functions).
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Currently the size of the relocation table will be shrunk
to the actual size needed. Although this gives a maximal
space saving, it messes up the _end symbol. This breaks
features like appended DTBs because the _end symbol doesn't
point to the real end of the U-Boot binary.
Remove the size shrinking and make the size of the relocation
table fixed but configurable. This follows the Linux approach
and the user can adjust the size to his needs.
Also rename the relocation table section from .rel to .data.reloc
to follow the Linux approach and to avoid ambiguities with the
.rel.* sections added by the linker.
Reported-by: Lars Povlsen <lars.povlsen@microsemi.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds the clock-frequency property to the SPI controller
DT node. It will be used by the SPI driver to calculate the baud rate.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds the necessary sysreset DT node and enables the required
drivers via Kconfig.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The Gardena Smart-Gateway boards have a MT7688 SoC with 128 MiB of RAM
and 8 MiB of flash (SPI NOR) and additional 128MiB SPI NAND storage.
This patch also includes 2 targets. One is the target that can be
programmed into the SPI NOR flash and a 2nd target "xxx-ram" is
added to support loading and booting via an already running U-Boot
version. This allows easy development and testing without the
need to flash the image each time.
Signed-off-by: Stefan Roese <sr@denx.de>
[fixed and regenerated defconfig files]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The LinkIt Smart 7688 modules have a MT7688 SoC with 128 MiB of RAM
and 32 MiB of flash (SPI NOR).
This patch also includes 2 targets. One is the target that can be
programmed into the SPI NOR flash and a 2nd target "xxx-ram" is
added to support loading and booting via an already running U-Boot
version. This allows easy development and testing without the
need to flash the image each time.
Signed-off-by: Stefan Roese <sr@denx.de>
[fixed and regenerated defconfig files]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds basic support for the MediaTek MT7620/88 SoCs. Parts of
the code is copied from the MediaTek GitHub repository:
https://github.com/MediaTek-Labs/linkit-smart-uboot.git
The mt7628a.dtsi file is imported from Linux v4.17.
Support for the LinkIt Smart 7688 module and the Gardena Smart Gateway
both based on the MT7688 will be added in further patches.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This is needed for the UBIFS support. The file is a copy of
arch/xtensa/include/asm/atomic.h
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Caches should be configured to mode CONF_CM_CACHABLE_NONCOHERENT
(or CONF_CM_CACHABLE_COW when a CM is available). There is no
need to make this configurable.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The index base address used for the cache initialisation is currently
hard-coded to CKSEG0. Make this value configurable if a MIPS system
needs to have a different address (e.g. in SRAM or ScratchPad RAM).
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Changing the Cache Coherency Algorithm (CCA) for kernel mode
requires executing from KSEG1. Thus do a jump from KSEG0 to KSEG1
before changing the CCA mode. Jump back to KSEG0 afterwards.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Those functions are not needed during cache init and can be
implemented in C. Only support the safe disabling of caches when
this is required for booting an OS. Reenabling caches is much
harder to implement if an optional coherency manager must be
supported. As there is no real use-case anyway, dcache_enable
is implemented with an error message.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Some MIPS systems store some board-specific boot configuration
in the U-Boot binary at offset 0x10. This is used by Malta boards
and by Lantiq/Intel SoC's when booting from parallel NOR flash.
Convert the hard-coded values to Kconfig options to remove such
board-specific stuff out of the generic start.S code. This also
deprecates the config option CONFIG_SYS_XWAY_EBU_BOOTCFG.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
All architectures have the same definition for s8/16/32/64
and u8/16/32/64.
Factor out the duplicated code into <asm-generic/int-ll64.h>.
BTW, Linux unified the kernel space definition into int-ll64.h
a few years ago as you see in Linux commit 0c79a8e29b5f
("asm/types.h: Remove include/asm-generic/int-l64.h").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This add the initial support of the broadcom reference
board bcm968380gerg with a bcm68380 SoC.
This board has 512 MB of RAM, 128 MB of flash (nand),
2 USB port, 1 UART, 4 ethernet ports and BCM43217 (wifi).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This adds the initial support of the Broadcom BCM6838 SoC familly,
only cpu, dram, uart and leds are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The only platform left for the AU1x00 SoCs was the pb1x00 platform, an
apparent clone of the dbau1x00 platform. As pb1x00 had no listed
maintainer I am assuming that it is also orphaned. Remove this platform
and then remove the unused SoC support.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
