On i.MX7ULP B0, there is change in NIC clock dividers architecture.
On A0, the NIC1 BUS and EXT dividers were in a chain with NIC1 DIV, but
on B0 they are parallel with NIC1 DIV. So now the dividers are independent.
This patch modifies the scg_nic_get_rate function according to this change.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The normal target frequency for ULP A7 core is 500Mhz, but now ROM
set the core frequency to 413Mhz. So change it to 500Mhz in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The GPU uses APLL PFD2 as its clock parent (483.84Mhz) with divider
set to 1. This frequecy is out of ULP A0 spec. The MAX rate for GPU
is 350Mhz. So we simply configure the APLL PFD2 to 345.6Mhz (FRAC=28)
to workaround the problem. The correct fix should let GPU handle the
clock rate in kernel.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The num/denom is a float value, but in the calculation it is convert
to integer 0, and cause the result wrong.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Wrong I2c driver configuration name is used in codes, so I2c driver is
not built. Correct it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since many drivers need this CONFIG_MX7ULP to distiguish the settings
for i.MX7ULP only. Add this entry to cpu's kconfig.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On i.MX7ULP, value zero is reserved in SCG1 RCCR register,
so the val should be decreased by 1 to get the correct clock
source index.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board will reboot if A7 core enter mem mode by rtc, then M4 core
enter VLLS mode after the RTC alarm expired. Enable the dumb PMIC mode
to fix this issue.
Since i.MX7ULP B0 moves the SNVS LP into M4 domain, A core can't access
it. So check the CPU rev and not apply the settings for B0.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Previously the SPL size on all iMX6 platforms was restricted to 68KB
because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
other iMX6 variants have 256KB of OCRAM. Add an option
CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
don't need to support the SL/DL variants. This allows for an SPL size of
196KB, which makes it much easier to use configurations such as SPL with
driver model and FDT control.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
There is no need to use HAB for FIT signature validation when
SPL_FIT_SIGNATURE is also enabled, as that will be validated via the
normal U-Boot signed FIT image flow.
This allows having SPL validated by HAB and the payloads to follow
being validated with FIT signatures only.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Toradex Apalis iMX6 modules are available in the iMX6D and iMX6Q
variants, which are quite similar and already managed via only one
dtb in u-boot (imx6-apalis.dtb). Select MX6Q via Kconfig by default in
order to automatically enable the HAS_CAAM and MX6_SMP features.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Add i.MX6ULZ cpu type and helper.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move these functions to the new header file and rename set_default_env()
to env_set_default() so that it has a consistent env_ prefix.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
1. This fixes linking issues when building with DM_VIDEO enabled mxsfb
driver.
2. Provide proper defines for both VIDEO=y and DM_VIDEO=y.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This patch solves the following warnings:
arch/arm/mach-stm32mp/psci.c:
warning: no previous prototype for ‘psci_set_state’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_arch_cpu_entry’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_features’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_version’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_affinity_info’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_migrate_info_type’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_cpu_on’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_cpu_off’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_system_reset’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_system_off’ [-Wmissing-prototypes]
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
For a single binary approach for imx6 quad/dual/duallite/solo it
is necessary to enable CONFIG_SATA for quad/dual. On the other hand
on imx6 duallite/sole SATA is not available.
Therefore sata_remove() is skipped according to a blacklist scheme.
Adding further imx derivates is probably not recessary as they are
usually not pin-compatible and therefore a different board with its
own configuration.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
According to iMX6DQ RM, the minor field (low 8 bits) in DIGPROG is not
aligned on silicon revision 1.3. So update get_cpu_rev to correct the
revision.
0x00630002 Silicon revision 1.2
0x00630005 Silicon revision 1.3
0x00630006 Silicon revision 1.6
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
New imx8 boards started adding duplicated UART init code.
Factor out this to common function sc_pm_setup_uart().
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Currently, when the spl_boot_device checks the boot device, it
will only return MMC1 when it's either sd or eMMC regardless
of whether or not it's MMC1 or MMC2. This is a problem when
booting from MMC2 if MMC isn't being manually configured like in
the DM_SPL case with SPL_OF_CONTROL.
This patch will check the register and return either MMC1 or MMC2.
Signed-off-by: Adam Ford <aford173@gmail.com>
Writing/updating boot image in nand device is not
straight forward in i.MX6 platform and it requires
boot control block(BCB) to be configured.
It becomes difficult to use uboot 'nand' command to
write BCB since it requires platform specific attributes
need to be taken care of.
It is even difficult to use existing msx-nand.c driver by
incorporating BCB attributes like mxs_dma_desc does
because it requires change in mtd and nand command.
So, cmd_nandbcb implemented in arch/arm/mach-imx
BCB contains two data structures, Firmware Configuration Block(FCB)
and Discovered Bad Block Table(DBBT). FCB has nand timings,
DBBT search area, page address of firmware.
On summary, nandbcb update will
- erase the entire partition
- create BCB by creating 2 FCB/DBBT block followed by
1 FW block based on partition size and erasesize.
- fill FCB/DBBT structures
- write FW/SPL on FW1
- write FCB/DBBT in first 2 blocks
for nand boot, up on reset bootrom look for FCB structure in
first block's if FCB found the nand timings are loaded for
further reads. once FCB read done, DTTB will load and finally
firmware will be loaded which is boot image.
Refer section "NAND Boot" from doc/imx/common/imx6.txt for more usage
information.
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
The name CONFIG_LEGACY_IMAGE_FORMAT reads slightly better along with
allowing us to avoid a rather nasty Kbuild/Kconfig issue down the line
with CONFIG_IS_ENABLED(IMAGE_FORMAT_LEGACY). In a few places outside of
cmd/ switch to using CONFIG_IS_ENABLED() to test what is set.
Signed-off-by: Tom Rini <trini@konsulko.com>
According to hab.c code we have to notify the ROM code if the MMU is
enabled or not. This is achieved by setting the "pu_irom_mmu_enabled"
to 0x1.
The current address in hab.c code is wrong for i.MX6SL, according to ROM
map file the correct address is 0x00901c60.
As we are writing in the wrong address the ROM code is not flushing the
caches when needed, and the following HAB event is observed in certain
scenarios:
--------- HAB Event 1 -----------------
event data:
0xdb 0x00 0x14 0x41 0x33 0x18 0xc0 0x00
0xca 0x00 0x0c 0x00 0x01 0xc5 0x00 0x00
0x00 0x00 0x07 0xe4
STS = HAB_FAILURE (0x33)
RSN = HAB_INV_SIGNATURE (0x18)
CTX = HAB_CTX_COMMAND (0xC0)
ENG = HAB_ENG_ANY (0x00)
Update MX6SL_PU_IROM_MMU_EN_VAR to address this issue.
Reported-by: Frank Zhang <frank.zhang@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Converted to use fsl_esdhc_imx for i.MX platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
The company Samtec was merged into Softing, migrate the board over to
the new name and update copyright headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
The DM iMX PCI driver has DM_FLAG_OS_PREPARE set and will call
imx_pcie_remove() from the .remove callback. Do not call it from
the architecture code again.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This commit adds initial support for the Toradex Apalis iMX8QM 4GB WB IT
V1.0B module. Unlike the V1.0A early access samples exclusively booting
from SD card, they are now strapped to boot from eFuses which are
factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Gigabit Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QM as of yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
CPU frequency reporting failed with the following error message being
printed:
sc_pm_get_clock_rate: resource:507 clk:2: res:3
Could not read CPU frequency: -22
CPU: NXP i.MX8QM RevB A53 at 0 MHz
Fix this by differentiating between the A35 as found on the i.MX 8QXP
and the A53 as found on the i.MX 8QM SoCs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
Correct uart clock root ID. Incorrect ID may result the
clock is gated because rate value 0 is returned in
imx_get_uartclk()
The ID can be ignored if CONFIG_SKIP_LOWLEVEL_INIT is not enabled
because init_clk_uart() will enable all uart clocks in that case.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Skip secure related initialization in arch_cpu_init if low level
init is skipped. Because these should be done in early stage
firmware, such as ARM trusted firmware.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
in case CONFIG_MULTI_DTB_FIT is set and u-boot-dtb.imx
image is build, currently u-boot-dtb.bin is used for
generating the u-boot-dtb.imx binary, which is wrong, as
it contains only a dtb blob not the fit.blob
Use instead the u-boot-fit-dtb.bin for generating
u-boot-dtb.imx which contains the fit.blob.
Signed-off-by: Heiko Schocher <hs@denx.de>
Add common plugin codes to call ROM's hwcnfg_setup and generate IVT2
header.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This commit adds initial support for the Toradex Colibri iMX8QXP 2GB WB
IT V1.0B module. Unlike the V1.0A early access samples exclusively
booting from SD card, they are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Building with Travis CI complained and stopped with the following error:
+cc1: fatal error: opening output file spl/u-boot-spl.cfgout: No such
file or directory
+compilation terminated.
This fixes commit caceb739ea ("imx: build flash.bin for i.MX8") which
took SPL being enabled on i.MX8 for granted.
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
We currently have duplicate definitions for BOARD_SIZE_CHECK in Makefile
and arch/arm/mach-imx/Makefile.
Move the board size check from arch/arm/mach-imx/Makefile to Makefile.
Depending on the value of CONFIG_BOARD_SIZE_LIMIT an error like an error
like the following is thrown:
u-boot-dtb.imx exceeds file size limit:
limit: 503696 bytes
actual: 509720 bytes
excess: 6024 bytes
make: *** [Makefile:1051: u-boot-dtb.imx] Error 1
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Extend the driver to build with DM_VIDEO enabled. DTS files
must additionally include 'u-boot,dm-pre-reloc' property in
soc and child nodes to enable driver binding to mxsfb device.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
Sometimes we met SERROR, but only to catch it when Linux boots up.
Let's enable catching in U-Boot to catch it ealier and ease debug.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Correct CPU_ARM926EJS1 to CPU_ARM926EJS.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Allow using bootaux also on VF610 aka Vybrid.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Extend the driver to build with DM_VIDEO enabled. DTS files
must additionally include 'u-boot,dm-pre-reloc' property in
soc and ipu nodes to enable driver binding to ipu device.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Currently the CPU frequency is incorrectly reported:
CPU: NXP i.MX8QXP RevB A35 at 147228 MHz
Fix this problem by using a direct call to the SCU firmware to
retrieve the Cortex A35 CPU frequency.
With this change applied the CPU frequency is displayed correctly:
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz
Tested-by: Marcelo Macedo <marcelo.macedo@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Select CONFIG_DM_MMC=y in order to support MMC driver model.
This allows the MMC board related code to be removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
This makes get_imx_reset_cause() accessible in SPL, but keeps the SRSR
register content intact so that U-Boot proper can evaluated the
reset_cause again should this be needed.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This patch extends the vf610 DDR memory controller code to support SW
leveling.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
This patch provides the code to calibrate the DDR's
DQS to DQ signals (RDLVL).
It is based on:
VFxxx Controller Reference Manual, Rev. 0, 10/2016, page 1600
10.1.6.16.4.1 "Software Read Leveling in MC Evaluation Mode"
and NXP's community thread:
"Vybrid: About DDR leveling feature on DDRMC."
https://community.nxp.com/thread/395323
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When framebuffer driver init is failed, we should return the err value not 0.
So the video init can exit immediately.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Passover info only for revA.
move get_cpu_rev out of CONFIG_CPU to avoid build failure when using
get_cpu_rev in SPL.
Add a CONFIG_SPL_BUILD for passover usage, no need to execute it again
in normal U-Boot stage. Also if still checking passover info in normal
U-Boot stage, need to make the passover code executed after
arch_cpu_init_dm.
So to make it easy and clean, only execute the code for SPL stage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Apply errata based on PL310 version instead of compile
time. Also set Prefetch offset to 15, since it improves
memcpy performance by 35%. Don't enable Incr double
Linefill enable since it adversely affects memcpy
performance by about 32MB/s and reads by 90MB/s. Tested
with 4K to 16MB sized src and dst aligned buffer.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
At default, u-boot reserves the memory from SP - 4KB to DRAM end for
lmb in arch_lmb_reserve. So lmb won't allocate any memory from it.
But we found the 4K gap for SP is not enough now, because some FDT
updating operations are added in our u-boot before jumping to kernel,
which needs larger stack. This causes the lmb allocated memory is overwritten
by stack.
Fix the issue by implementing the board_lmb_reserve to reserve from
SP - 16KB to memory end for lmb.
Signed-off-by: Ye Li <ye.li@nxp.com>
SPL runs in EL3 mode, except MU0_A, others are not powered on,
and could not be used. However normal U-Boot use MU1_A, so we
could not reuse the one in dts. And we could not replace the one
in dts with MU0_A, because MU0_A is reserved in secure world.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Like it was done on imx6 in commit 9236269de5 ("imx: mx6: Fix
implementantion reset_misc")
Do not call lcdif_power_down() in the SPL case to fix the following
build error:
LD spl/u-boot-spl
MKIMAGE u-boot.img
arch/arm/mach-imx/built-in.o: In function `reset_misc':
/home/fabio/ossystems/u-boot/arch/arm/mach-imx/mx7/soc.c:372: undefined reference to `lcdif_power_down'
scripts/Makefile.spl:375: recipe for target 'spl/u-boot-spl' failed
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
the PHYTEC phyCORE-i.MX6UL SOM (PCL063).
CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 44C
Reset cause: POR
Board: PHYTEC phyCORE-i.MX6UL
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
The following NXP application notes and manual recommend to ensure the
IVT DCD pointer is Null prior to calling HAB API authenticate_image()
function:
- AN12263: HABv4 RVT Guidelines and Recommendations
- AN4581: Secure Boot on i.MX50, i.MX53, i.MX 6 and i.MX7 Series using
HABv4
- CST docs: High Assurance Boot Version 4 Application Programming
Interface Reference Manual
Commit ca89df7dd4 ("imx: hab: Convert DCD non-NULL error to warning")
converted DCD non-NULL error to warning due to the lack of documentation
at the time of first patch submission. We have warned U-Boot users since
v2018.03, and it makes sense now to follow the NXP recommendation to
ensure the IVT DCD pointer is Null.
DCD commands should only be present in the initial boot image loaded by
the SoC ROM. Starting in HAB v4.3.7 the HAB code will generate an error
if a DCD pointer is present in an image being authenticated by calling the
HAB RVT API. Older versions of HAB will process and run DCD if it is
present, and this could lead to an incorrect authentication boot flow.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
OSC_27M_CLK should return 27MHz and OSC_32K_CLK should return
32768Hz to reflect the reality.
This also keeps the values in sync with the Linux clock tree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The CPU banner printed is as following:
CPU: CPU: Freescale i.MX8QXP RevB A35 at 147228 MHz
1. Drop the CPU:
2. Change vendor from Freescale to NXP
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current value CTLUPD_AREF(0) is the reset value of the register,
so there is no need to write a value. If needed, the register can be
written using board specific CR settings.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
The CR80 register has multiple interrupt bits, the code is supposed
to check bit 8 but instead uses a logical and. In most cases this
probably did not affect real operations since at that stage typically
none of the other bits are set.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The Vybrid reference manual VFXXXRM Rev. 0 10/2016 states in chapter
5.2.6.1 DUMMY PADS (DDR/QuadSPI) that those pads need to be programed
for correct operation of DDR. Assume the default DDR pin configuration
which seems to work well on a Colibri VF50.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Build flash.bin for i.MX8MQ, it will include signed hdmi firmware,
spl, ddr firmware, fit image(bl31.bin, u-boot-nodtb.bin, dtb).
Burn it to 33KB offset of SD card.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Refactor dram_pll_init to accept args to configure different pll freq.
Introduce dram_enable_bypass and dram_disable_bypass
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Build u-boot-dtb.cfgout before checking files, otherwise
u-boot-dtb.cfgout is generated at late stage and cause final image not
generated.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Current implementation of hab_auth_img command needs ivt_offset to
authenticate the image. But ivt header is placed at the end of image
date after padding.
This leaves the usage of hab_auth_img command to fixed size or static
offset for ivt header. New function "get_image_ivt_offset" is introduced
to find the ivt offset during runtime. The case conditional check in this
function is same as boot_get_kernel in common/bootm.c
With this variable length image e.g. FIT image with any random size can
have IVT at the end and ivt_offset option can be left optional
Can be used as "hab_auth_img $loadaddr $filesize" from u-boot script
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Breno Lima <breno.lima@nxp.com>
Introduce two board level callback functions to FIT image loading process, and
a SPL_FIT_FOUND flag to differentiate FIT image or RAW image.
Implement functions in imx common SPL codes to call HAB funtion
to authenticate the FIT image. Generally, we have to sign multiple regions
in FIT image:
1. Sign FIT FDT data (configuration)
2. Sign FIT external data (Sub-images)
Because the CSF supports to sign multiple memory blocks, so that we can use one
signature to cover all regions in FIT image and only authenticate once.
The authentication should be done after the entire FIT image is loaded into
memory including all sub-images.
We use "-p" option to generate FIT image to reserve a space for FIT IVT
and FIT CSF, also this help to fix the offset of the external data (u-boot-nodtb.bin,
ATF, u-boot DTB).
The signed FIT image layout is as below:
--------------------------------------------------
| | | | | | | |
| FIT | FIT | FIT | | U-BOOT | ATF | U-BOOT |
| FDT | IVT | CSF | | nodtb.bin | | DTB |
| | | | | | | |
--------------------------------------------------
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Using ulong is wrong as its size depends on the Host CPU architecture
(32-bit vs. 64-bit) although the Cortex-M4 is always 32-bit.
Without this patch, the stack and PC are obviously wrong and it
generates an abort when used on 64-bit processors such as the i.MX8MQ.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Otherwise can't boot the M4 core as it is impossible to load its
firmware into the TCM memory.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
