AM62 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM625 SoC. It supports the following interfaces:
* 2 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 HDMI Port with audio + x1 OLDI/LVDS Display interface for Dual Display
* x1 Headphone Jack
* x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x4 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 20-pin header for Programmable Realtime Unit (PRU) IO pins
* 15-pin CSI header
Add basic support for AM62-SK.
To keep the changes to minimum. Only UART And SD are supported at the
moment. This should serve as good example for adding new board support
based on AM62x SoC
Schematics: https://www.ti.com/lit/zip/sprr448
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add basic support for AM62 SK. This has 2GB DDR.
Note that stack for R5 SPL is in OCRAM @ 0x7000ffff so that is away from
BSS and does not step on BSS section
Add only the bare minimum required to support UART and SD.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Introduce autogenerated SoC data support clk and device data for the
AM62. Hook it upto to power-domain and clk frameworks of U-Boot.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The AM62 SoC family is the follow on AM335x built on K3 Multicore SoC
architecture platform, providing ultra-low-power modes, dual display,
multi-sensor edge compute, security and other BOM-saving integration.
The AM62 SoC targets broad market to enable applications such as
Industrial HMI, PLC/CNC/Robot control, Medical Equipment, Building
Automation, Appliances and more.
Some highlights of this SoC are:
* Quad-Cortex-A53s (running up to 1.4GHz) in a single cluster.
Pin-to-pin compatible options for single and quad core are available.
* Cortex-M4F for general-purpose or safety usage.
* Dual display support, providing 24-bit RBG parallel interface and
OLDI/LVDS-4 Lane x2, up to 200MHz pixel clock support for 2K display
resolution.
* Selectable GPUsupport, up to 8GFLOPS, providing better user experience
in 3D graphic display case and Android.
* PRU(Programmable Realtime Unit) support for customized programmable
interfaces/IOs.
* Integrated Giga-bit Ethernet switch supporting up to a total of two
external ports (TSN capable).
* 9xUARTs, 5xSPI, 6xI2C, 2xUSB2, 3xCAN-FD, 3x eMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 3xMcASP for audio,
1x CSI-RX-4L for Camera, eCAP/eQEP, ePWM, among other peripherals.
* Dedicated Centralized System Controller for Security, Power, and
Resource Management.
* Multiple low power modes support, ex: Deep sleep,Standby, MCU-only,
enabling battery powered system design.
AM625 is the first device of the family. Add DT bindings for the same.
More details can be found in the Technical Reference Manual:
https://www.ti.com/lit/pdf/spruiv7
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The node name of the bus in the device tree has changed. Also, the length
argument to be passed should be the length of new value. Therefore, fix the
path to usb device tree node as well as the length argument passed.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
For dfu boot mode, the clocks property needs to be deleted and dr_mode
needs to be set to peripheral. Therefore, add the required fixes for the
same.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This is the initial support for Broadcom's ARM-based 47622 SOC.
In this change, our first SOC is an armv7 platform called 47622. The
initial support includes a bare-bone implementation and dts with ARM
PL011 uart.
The SOC-specific code resides in arch/arm/mach-bcmbca/<soc> and board
related code is in board/broadcom/bcmba.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Add wkup_gpio pinmux setting which will be used for performing the
DT fixup for hbmc node according to mux selection state, on J721E
EVM, hypermux sel is tied to ·WKUP_GPIO0_8.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Add DT node for HyperBus Memory Controller and hbmc-mux in the
FSS. hbmc-am654 driver uses syscon_get_regmap() call which fails
with current compatible setting.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
This uses the nvmem API to load a mac address from an RTC.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This uses an i2c eeprom to load a mac address using the nvmem interface.
Enable I2C_EEPROM for sandbox SPL since it is the only sandbox config
which doesn't enable it eeprom.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This prevents some conflicts when running sandbox with -D, since the
"rom" mac address will be random and won't match the environment. We
still need to keep addresses for eth1 and eth6 in the environment,
because dm_test_eth_rotate expects to be able to disable them by
removing their envaddr variables. This can likely be fixed in a future
series by adding a function to cause sandbox eth_opts callback for a
particular mac to fail immediately.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of reading a pseudo-rom mac address from the device tree, just use
whatever we get from write_hwaddr. This has the effect of using the mac
address from the environment (or from the device tree, if it is
specified).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
CONFIG_VAL(DEBUG_UART_BASE) expands to CONFIG_DEBUG_UART_BASE or
CONFIG_SPL_DEBUG_UART_BASE or CONFIG_TPL_DEBUG_UART_BASE and allows boards
to set different values for SPL, TPL and U-Boot Proper.
For ns16550 driver this support is there since commit d293759d55
("serial: ns16550: Add support for SPL_DEBUG_UART_BASE").
Signed-off-by: Pali Rohár <pali@kernel.org>
Update the way KWB_CFG_SEC_BOOT_DEV is determined to use
CONFIG_MVEBU_SPL_BOOT_DEVICE_{SPI,MMC} instead of
CONFIG_SPL_BOOT_DEVICE.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
In some cases, when we don't use CONFIG_SPL_FRAMEWORK nor are we on
PowerPC using their specific SPL/TPL framework, we need to specify the
start.S file to use for these typically very constrained systems. Do
this within the Makefile logic, rather than introducing a string-based
CONFIG option, as this would get slightly complex to do in Kconfig for a
very limited number of users.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the places where PowerPC references CONFIG_SYS_GBL_DATA_OFFSET it
does so as (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET). And
it defines CONFIG_SYS_GBL_DATA_OFFSET in the same manner that other
architectures define CONFIG_SYS_INIT_SP_OFFSET. Other architectures
define CONFIG_SYS_INIT_SP_ADDR as (CONFIG_SYS_INIT_RAM_ADDR +
CONFIG_SYS_INIT_SP_OFFSET) typically. Rename things within PowerPC for
consistency with other architectures.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, since we know that in the combination of
CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET all of the "high"
bits are in CONFIG_SYS_INIT_RAM_ADDR and "low" bits are in
CONFIG_SYS_GBL_DATA_OFFSET we reference this separately in start.S, but
added together everywhere else. For clarity consistency, reference the
combined value here instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
The definition of CONFIG_SPL_BOOTROM_SAVE is always a fixed
CONFIG_SPL_STACK + 4, while CONFIG_SPL_STACK is not constant. This
change will make it clear where the location is still, once
CONFIG_SPL_STACK moves to Kconfig.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of PowerPC platforms define this, for SPL. To move this to
Kconfig, it needs to be CONFIG_SPL_SYS_CCSR_DO_NOT_RELOCATE, so use
CONFIG_IS_ENABLED() to check for usage. A number of layerscape
platforms bring this logic from PowerPC, but only need a small part of
it, for the fman driver. Remove their unused portion at least.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_INIT_MINIMAL
CONFIG_SPL_FLUSH_IMAGE
CONFIG_SPL_SKIP_RELOCATE
Signed-off-by: Tom Rini <trini@konsulko.com>
This is always defined to 2, and referenced in two places. Move the
define to <asm/omap_common.h> and make sure the code that uses this
includes that file. Make <asm/arch-omap*/clock.h> not include that
file, as we don't need to be doing so.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since the power domain driver default select CONFIG_CLK, so we will
meet lots failures without CLK_IMX8MQ, so default select it.
Fixes: commit 4eb82c2e56 ("imx: power-domain: Get rid of SMCCC dependency")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The AArch64 TCR_ELx register is a 64-bit register, and many newer
architecture features use bits in the upper half. So far U-Boot was
igorant of those bits, trying to leave them alone.
However, in an effort to set bit 31 to 1, it failed doing so, because
the compiler sign-extended "1 << 31", so that all bits[63:31] got set.
Older ARMv8.0 cores don't define anything dangerous up there, but newer
architecture revisions do, and setting all those bits will end badly:
=================
$ qemu-system-aarch64 -cpu max ....
U-Boot 2022.07-rc1 (May 09 2022 - 15:21:00 +0100)
DRAM: 1.5 GiB
================= (hangs here)
Defining TCR_ELx_RSVD to "1U << 31" avoids the sign-extension, so all
upper bits stay at a safe 0 value. This means no more surprises when
U-Boot runs on a more capable CPU core.
Reported-by: Balaji Anandapadmanaban <Balaji.Anandapadmanaban@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Peter Collingbourne <pcc@google.com>
Since commit dffdb1f8eb ("board: ti: am64x: Use fdt functions
for ram and bank init") ddr_init() and dram_bank_init() have
switched to fdtdec for getting the memory configuration from
the am64xx dts files instead of using hardcoded values. This
requires an accessible memory node in SPL as we already have
in k3-am642-r5-evm.dts.
Make the memory node accessible in A53 SPL for both am642-sk
and am642-evm and in am642-sk R5 SPL.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Clean up asm/io.h by
- removing commented code
- removing outdated comments
- removing unused definitions (for mem_isa, mem_pci)
This massively improves the readability of the file.
Suggested by commits:
7ab2e47d27 ("arm: Clean up asm/io.h")
909d0399a5 ("ARM: asm/io.h: kill off confusing #ifdef __mem_pci block")
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Commit ba1ed5b022 ("Convert CONFIG_ARCH_MAP_SYSMEM to Kconfig") clearly
defined that this option is available for SANDBOX (was also for already
removed NDS32). That's why there is no way how this code can be enabled
with current Kconfig layout for riscv.
Based on this removing this code.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYo4bYwAKCRDKSWXLKUoM
IYmTAJ9t4GDXggJ7ErB3Kk7/qSrywjEGAgCgnKQVgQvjo1B6o5aiwbk1wR86zkQ=
=W7X8
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc4' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc4
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
The bulk of it is (finally!) some DT sync from the kernel. We refrained
from syncing one incompatible change, as this would spoil booting Linux
kernels before v5.13 with U-Boot's DT (via UEFI, for instance).
I test booted Linux v5.18 and v5.4 with that new DT on some boards, and
the headless peripherals (MMC, USB, Ethernet) seemed to work.
The rest are fixes:
- silencing missing clock warnings due to the new pinctrl driver
- fixing "UART0 on PortF", allowing UART access through the SD card pins
- add an F1C100s clock driver, to enable MMC support (SPI comes later)
- some cleanups for CONS_INDEX_n in Kconfig
Tested on BananaPi-M1, Pine64-LTS, Pine-H64, X96-Mate (H616) and
OrangePi-Zero.
ARCH_SUNXI selects DM_SERIAL, so the condition can never be satisfied.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When CONFIG_UART0_PORT_F is defined, we try to configure two PortF pins
(usually used for the SD card) as UART0. Some SoCs use the mux value of
3 for this, while others use 4.
The combination of Kconfig symbols we currently use was not quite right:
we mis-configure the A31, A64, H6 and H616.
Going through the list in the pinctrl driver, there are only a few older
SoCs that use a value of 4, so revert the #ifdef clause, and name those
explicitly, instead of the other way around.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Use the de10-nano files as templates for the de10-standard board.
The files in qts directory are generated by quartus from the GHRD
design.
Signed-off-by: Humberto Naves <hsnaves@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This would prevent configuring non-secure regs in case gic security
extensions are not emulated in Qemu.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Commit e8c0e0064c ("powerpc: mpc85xx: Fix CONFIG_OF_SEPARATE support")
fixed SD card booting on mpc85xx boards but broke NOR booting on these
boards. Reason is that U-Boot build system for NOR images uses binman and
this binman ignores alignment defined in linker script. Instead it has own
config file where is alignment defined.
Fix binman alignment for mpc85xx boards to match what is _now_ defined in
linker script.
This change fixes building of U-Boot for NOR booting on P2020 board.
Fixes: e8c0e0064c ("powerpc: mpc85xx: Fix CONFIG_OF_SEPARATE support")
Signed-off-by: Pali Rohár <pali@kernel.org>
