Commit graph

1026 commits

Author SHA1 Message Date
Ian Campbell
49692c5f51 net/designware: Make DMA burst length configurable and reduce by default
The correct value for this setting can vary across SoCs and boards, so make it
configurable.

Also reduce the default value to 8, which is the same default as used in the
Linux driver.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
2014-05-25 17:23:58 +02:00
Ian Campbell
1857075a7f net/designware: reorder struct dw_eth_dev to pack more efficiently.
On Thu, 2014-05-08 at 22:26 +0100, Ian Campbell wrote:
> The {r,t}xbuffs fields also need to be aligned. Previously this was done
> implicitly because they immediately followed the descriptor tables. Make this
> explicit and also move to the head of the struct.

Looks like I managed to not actually commit the move of the field to the
head of the struct! v3.1 follows....

Ian.

8<------------

>From 2937ba01841887317f6792709ed57cb86b5fc0cd Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Thu, 1 May 2014 19:45:15 +0100
Subject: [PATCH] net/designware: reorder struct dw_eth_dev to pack more
 efficiently.

The {tx,rx}_mac_descrtable fields are aligned to ARCH_DMA_MINALIGN, which could
be 256 or even larger. That means there is a potentially huge hole in the
struct before those fields, so move them to the front where they are better
packed.

Moving them to the front also helps ensure that so long as dw_eth_dev is
properly aligned (which it is since "net/designware: ensure device private data
is DMA aligned.") the {tx,rx}_mac_descrtable will be too, or at least avoids
having to worry too much about compiler specifics.

The {r,t}xbuffs fields also need to be aligned. Previously this was done
implicitly because they immediately followed the descriptor tables. Make this
explicit and also move to the head of the struct.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
2014-05-25 17:23:48 +02:00
Ian Campbell
964ea7c1ce net/designware: ensure cache invalidations are aligned to ARCH_DMA_MINALIGN
This is required at least on ARM.

When sending instead of simply invalidating the entire descriptor, flush
as little as possible while still respecting ARCH_DMA_MINALIGN, as
requested by Alexey.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
2014-05-25 17:23:15 +02:00
Ian Campbell
1c848a2586 net/designware: ensure device private data is DMA aligned.
struct dw_eth_dev contains fields which are accessed via DMA, so make sure it
is aligned to a dma boundary. Without this I see:
    ERROR: v7_dcache_inval_range - start address is not aligned - 0x7fb677e0

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Marek Vasut <marex@denx.de>
2014-05-25 17:23:12 +02:00
Chunhe Lan
ffc8667acf net: phy/vitesse: Add support for VSC8664 phy module
This patch adds support for VSC8664 PHY module which can
be found on Freescale's T4240RDB boards.

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-05-16 16:24:05 -05:00
Shengzhou Liu
5122dfae5d powerpc/85xx: add T4080 SoC support
The T4080 SoC is a low-power version of the T4160.
T4080 combines 4 dual-threaded Power Architecture e6500
cores with single cluster and two memory complexes.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2014-05-13 08:26:54 -07:00
Shaohui Xie
3a7ed5aa23 powerpc/fman/memac: use default MDIO_HOLD value
Current driver uses a Maximum value for MDIO_HOLD when doing 10G MDIO
access, this is due to an errata A-006260 on T4 rev1.0 which is fixed
on rev2.0, so remove the maximum value to use the default value for rev2.0.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2014-05-13 08:26:54 -07:00
Ian Campbell
15e82e5309 net/designware: call phy_connect_dev() to properly setup phylib device
This sets up the linkage from the phydev back to the ethernet device. This
symptom of not doing this which I noticed was:
    <NULL> Waiting for PHY auto negotiation to complete....
rather than:
    dwmac.1c50000 Waiting for PHY auto negotiation to complete....

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
2014-05-12 16:31:51 -04:00
Masahiro Yamada
da384a9d76 net: rename and refactor eth_rand_ethaddr() function
Some functions in include/net.h are ported from
include/linux/etherdevice.h of Linux Kernel.

For ex.
  is_zero_ether_addr()
  is_multicast_ether_addr()
  is_broadcast_ether_addr()
  is_valid_ether_addr();

So, we should use the same function name as that of Linux Kernel,
eth_rand_addr(), for consistency.

Besides, eth_rand_addr() has been implemented as an inline function.
So it should not be surrounded by #ifdef CONFIG_RANDOM_MACADDR.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2014-05-12 15:19:46 -04:00
Shengzhou Liu
597fe041a8 net/phy: enable get_phy_id redefinable
As some PHYs have non-standard PHY ID registers, PHY Id can't
be read correctly by current get_phy_id function, so we enable
get_phy_id redefinable to permit specific PHY driver having own
specific get_phy_id function.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2014-05-12 15:19:45 -04:00
Xiaobo Xie
02aa4c5388 AR8035/phy: Enable autonegotiation function for ar8035
Function "genphy_parse_link()" used "if (mii_reg & BMSR_ANEGCAPABLE)" before,
but used "if (phydev->supported & SUPPORTED_Autoneg)" now.
So assign "phydev->supported" to "phydev->drv->features" for ar8035
to enable autonegotiation. Then removed the genphy_config_aneg() function.

Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
2014-05-12 15:19:45 -04:00
Albert ARIBAUD
d2a3e91139 Merge branch 'u-boot/master'
Conflicts:
	drivers/net/Makefile

(trivial merge)
2014-05-09 11:50:14 +02:00
Michal Simek
2fd2489b7a net: zynq: Fix sparse warnings in gem
Add missing header.

Warnings:
drivers/net/zynq_gem.c:491:5: warning: symbol 'zynq_gem_initialize' was not declared. Should it be static?
drivers/net/zynq_gem.c:542:5: warning: symbol 'zynq_gem_of_init' was not declared. Should it be static?

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-06 13:41:55 +02:00
Michal Simek
c1a9fa4ba6 net: zynq: Use predefined macros instead of hardcoded value
MII is used by this driver.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-06 13:41:33 +02:00
Tom Rini
080d897585 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2014-04-25 14:53:51 -04:00
Zhao Qiang
08ad9b068a ar8031: modify the config func of ar8031 to ar8021_config
ar8031 has the same config steps with ar8021, so change its
config func to ar8021_config instead of genphy_config.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:53 -07:00
Priyanka Jain
2ee6c52e22 driver/net/fm/memac_phy: Initialize mdio_clock for SoCs wih FMANv3
MDIO clock needs to be initialized in u-boot code for SoCs
having FMAN-v3(v3H or v3L) controller due to below reasons

-On SoCs that have FMAN-v3H  like B4860, default value of
MDIO_CLK_DIV bits in mdio_stat(mdio_cfg) register generates
mdio clock too high (much higher than 2.5MHz), violating the
IEEE specs.
-On SOCs that have FMAN-v3L like T1040, default value of
MDIO_CLK_DIV bits is zero, so MDIO clock is disabled.

So, for proper functioninig of MDIO, MDIO_CLK_DIV bits needs to
be properly initialized.
Also this type of initialization is generally done in
PBI(pre-bootloader) phase using rcw.But for chips like T1040
which support deep-sleep, such type of initialization cannot be
done in PBI phase due to the limitation that during deep-sleep
resume, FMAN (MDIO) registers are not accessible in PBI phase.
So, mdio clock initailization must be done as part of u-boot.

This initialization code is implemented in memac_phy.c which
gets compiled only for SoCs having FMANv3, so no extra compilation
flag is required.

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:49 -07:00
Codrin Ciubotariu
44afbbc0f0 net/phy: Fix PHY id for VSC8514
In the current Datasheet for VSC8514 there is a mistake, saying that
the PHY id is 0x70570. The real value in the identifier registers is
0x70670. Linux PHY driver uses 0x70670 also.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:47 -07:00
Zhao Qiang
dcf1d774bf QE/FMAN: modify CONFIG_SYS_QE_FMAN_FW_ADDR to CONFIG_SYS_FMAN_FW_ADDR and CONFIG_SYS_QE_FW_ADDR
CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address.
Now using CONFIG_SYS_FMAN_FW_ADDR for Fman microcode address,
and CONFIG_SYS_QE_FW_ADDR for QE microcode address.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:47 -07:00
Daniel Schwierzeck
538cf92c8c MIPS: drop incaip board
This is dead hardware and no one is interested in making the
necessary changes for upcoming features like generic board or
driver model.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
2014-04-20 13:16:43 +02:00
David Müller (ELSOFT AG)
d2ff5e55c3 e1000: remove redundant assignment
Signed-off-by: David Mueller <d.mueller@elsoft.ch>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2014-04-18 16:14:10 -04:00
Paul Burton
6fb49e4aa0 pcnet: force ordering of descriptor accesses
The ordering of accesses to the rx & tx descriptors is important, yet
the send & recv functions accessed them via regular structure accesses.
This leaves the compiler with the opportunity to reorder those accesses
or to hoist them outside of loops. Prevent that from happening by using
readl & writel to access the descriptors. As a nice bonus, this removes
the need for the driver to care about endianness.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-18 10:42:30 -04:00
Paul Burton
a354ddc3d7 pcnet: align rx buffers for cache invalidation
The RX buffers are invalidated when a packet is received, however they
were not suitably cache-line aligned. Allocate them seperately to the
pcnet_priv structure and align to ARCH_DMA_MINALIGN in order to ensure
suitable alignment for the cache invalidation, preventing anything else
being placed in the same lines & lost.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-18 10:42:30 -04:00
Paul Burton
f1ae382dfd pcnet: access descriptor rings & init block uncached
The prior accesses to the descriptor rings & init block via cached
memory had a few issues:

  - The memory needs cache flushes or invalidation at the appropriate
    times, but was not necessarily aligned on cache line boundaries.
    This could lead to data being incorrectly lost or written back to
    RAM at the wrong time.

  - There are points where ordering of writes to the memory is
    important, but because it's cached memory the pcnet controller
    would see cache lines written back ordered by address. This could
    occasionally lead to hardware seeing descriptors in an incorrect
    state.

  - Flushing the cache constantly is inefficient.

So, to avoid all of those issues simply access the descriptors & init
block via uncached memory. The MIPS-specific UNCACHED_SDRAM macro is
used to do this (retrieving an address in kseg1) as I could see no
existing generic solution. Since the MIPS Malta board is the only user
of the pcnet driver, hopefully this doesn't matter.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-18 10:42:30 -04:00
Masahiro Yamada
36bf57b6fb arm: remove lubbock board support
Enough time has passed since this board was moved to Orphan. Remove.

 - Remove board/lubbock/*
 - Remove include/configs/lubbock.h
 - Cleanup defined(CONFIG_LUBBOCK)
 - Move the entry from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-04-18 10:42:30 -04:00
Karicheri, Muralidharan
fc9a8e8d40 keystone2: net: add keystone ethernet driver
Ethernet driver configures the CPSW, SGMI and Phy and uses
the the Navigator APIs. The driver supports 4 Ethernet ports and
can work with only one port at a time.

Port configurations are defined in board.c.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
2014-04-17 17:24:39 -04:00
Albert ARIBAUD
519fdde9e6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	include/configs/trats.h
	include/configs/trats2.h
	include/mmc.h
2014-04-08 09:25:08 +02:00
Alexey Brodkin
a7b26dbb49 net/designware: align DMA buffer descriptors to D$ line
It's important to have ability to flush/invalidate each DMA buffer descriptor
individually to prevent incoherency of adjacent BDs.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
2014-03-28 15:06:30 -04:00
Ilya Ledvich
ef59bb7cc8 drivers: net: cpsw: init phy with gigabit features
CPSW ia a gigabit device. Use the PHY_GBIT_FEATURES macro to determine phy
supported features.
Tested on cm_t335.

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
2014-03-12 16:22:12 -04:00
Tom Rini
5495dae7aa Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-03-10 14:22:54 -04:00
Haijun.Zhang
dc116bd6c4 net/phy: Correct AR8021 phy_mask
There was wrong phy_mask for AR8021 device,
so the AR8021 can't be probed correctly.
Changed it from 0x4fffff to 0x4ffff0.

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
2014-03-07 10:59:06 -05:00
Mugunthan V N
9c653aad16 drivers: net: cpsw: add support to have phy address from cpsw platform data
Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04 09:41:53 -05:00
Michal Simek
f88a6869a1 net: gem: Add OF initialization support
Gem can be directly initialized from DTB.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-03-04 09:27:35 -05:00
Michal Simek
0c9c99a20b net: emaclite: Fix OF initialization
- Add xilinx_emaclite_of_init to netdev.h
- Remove global data pointer from the driver
- Add better handling for error state.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-03-04 09:27:32 -05:00
Tom Rini
a7e8c15f71 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
With this, fixup a trivial build error of get_effective_memsize needing
to be updated in the new board/freescale/p1010rdb/spl.c

Signed-off-by: Tom Rini <trini@ti.com>
2014-02-25 13:55:49 -05:00
Zhao Qiang
e0d809647f ar8031/8033/phy:enable autonegotiation for ar8031/8033
Function "genphy_parse_link()" used "if (mii_reg & BMSR_ANEGCAPABLE)" before
while "if (phydev->supported & SUPPORTED_Autoneg)" now.
So assign "phydev->supported" to "phydev->drv->features" for ar8031/8033
to enable autonegotiation.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-24 15:23:41 -08:00
Bhupesh Sharma
ee456337c6 SMC91111: Fix compilation warnings
This patch fixes the following warning messages coming out of
'drivers/net/smc91111.h' when compiled for 'vexpress_aemv8a':

warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]

Currently this issue seems to surface when SMSC is compiled for 64-bit
ARMv8 platforms, so the change is protected under CONFIG_ARM64, so that
it doesn't break other existing platforms.

In addition this patch tries to fix some checkpatch errors and warnings
(others related to camel-casing and volatile usage will be addressed
by a later patch).

This fix has been tested on both ARMv8 foundation model v1 and v2.

Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
2014-02-21 11:33:18 -05:00
Tom Rini
6853e6aa77 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-20 12:18:59 -05:00
Tom Rini
130fbeb1c5 blackfin: Add <asm/clock.h> to numerous drivers
With d6a320d we moved some clock externs out of blackfin_local.h and
into clock.h but now need to include <asm/clock.h> in more drivers to
avoid warnings.

Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-20 12:00:27 -05:00
Albert ARIBAUD
3e11350255 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	Makefile
	drivers/net/npe/Makefile

These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.
2014-02-20 13:16:05 +01:00
Masahiro Yamada
6825a95b0b kbuild: use Linux Kernel build scripts
Now we are ready to switch over to real Kbuild.

This commit disables temporary scripts:
  scripts/{Makefile.build.tmp, Makefile.host.tmp}
and enables real Kbuild scripts:
  scripts/{Makefile.build,Makefile.host,Makefile.lib}.

This switch is triggered by the line in scripts/Kbuild.include
  -build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build.tmp obj
  +build := -f $(if $(KBUILD_SRC),$(srctree)/)scripts/Makefile.build obj

We need to adjust some build scripts for U-Boot.
But smaller amount of modification is preferable.

Additionally, we need to fix compiler flags which are
locally added or removed.

In Kbuild, it is not allowed to change CFLAGS locally.
Instead, ccflags-y, asflags-y, cppflags-y,
CFLAGS_$(basetarget).o, CFLAGS_REMOVE_$(basetarget).o
are prepared for that purpose.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
2014-02-19 11:07:50 -05:00
Heiko Schocher
9137d19bdd net, phy: atheros ar803x bug
commit 626ee1e3 "phylib: update atheros ar803x phy"

leads in failing ethernet on the pxm2 board.

Calling genphy_config() instead of ar8021_config(),
which seems for ar8021 phys not ar803x phys, make
it working again.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
2014-02-19 10:47:33 -05:00
Albert ARIBAUD
e7538fee99 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-02-19 12:04:45 +01:00
Soren Brinkmann
97598fcf10 net: zynq_gem: Calculate clock dividers dynamically
Remove hard coded clock divider setting and use the Zynq clock framework
to dynamically calculate appropriate dividers at run time.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Soren Brinkmann
1cd46ed2d3 net: zynq_gem: Move RCLK details out of driver
The GEM driver should not need to know about Zynq specific details of
RCLK related registers and bitfields in the SLCR. Move those details to
the slcr driver.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Albert ARIBAUD
a87a0ce702 Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master' 2014-02-19 07:15:01 +01:00
Stefano Babic
17998eff90 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-11 12:55:32 +01:00
Markus Niebel
6ba45cc0f8 NET: fec_mxc: fix MDIO clock prescaler calculation
The prescaler value for MDC is calculated wrong for
MX6S. Implement the same logic as linux here which handles
ENET_MAC different then original FEC.

Tested on a custom board with i.MX6S and 100MBit PHY

Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
2014-02-11 11:33:45 +01:00
Alexey Brodkin
50b0df814b net/designware: make driver compatible with data cache
Up until now this driver only worked with data cache disabled.
To make it work with enabled data cache following changes were required:

 * Flush Tx/Rx buffer descriptors their modification
 * Invalidate Tx/Rx buffer descriptors before reading its values
 * Flush cache for data passed from CPU to GMAC
 * Invalidate cache for data passed from GMAC to CPU

Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2014-02-07 09:17:05 -05:00
Alexey Brodkin
92a190aaab net/designware - switch driver to phylib usage
With this change driver will benefit from existing phylib and thus
custom phy functionality implemented in the driver will go away:
 * Instantiation of the driver is now much shorter - 2 parameters
instead of 4.
 * Simplified phy management/functoinality in driver is replaced with
rich functionality of phylib.
 * Support of custom phy initialization is now done with existing
"board_phy_config".

Note that after this change some previously used config options
(driver-specific PHY configuration) will be obsolete and they are simply
substituted with similar options of phylib.

For example:
 * CONFIG_DW_AUTONEG - no need in this one. Autonegotiation is enabled
by default.
 * CONFIG_DW_SEARCH_PHY - if one wants to specify attached phy
explicitly CONFIG_PHY_ADDR board config option has to be used, otherwise
automatically the first discovered on MDIO bus phy will be used

I believe there's no need now in "doc/README.designware_eth" because
user only needs to instantiate the driver with "designware_initialize"
whose prototype exists in "include/netdev.h".

Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2014-02-07 09:16:46 -05:00
Alexey Brodkin
74cb708d58 net/designware: add explicit reset of {tx|rx}_currdescnum
Driver "init" function might be called multiple times.
On every "init" Tx/Rx buffer descriptors are initialized: "descs_init"
-> "{tx|rx}_descs_init".

In its turn those init functions set MAC's "{tx|rx}desclistaddr" to
point on the first buffer descriptor in the list.

So CPU to start operation from the first buffer descriptor as well after
every "init" we have to reset "{tx|rx}_currdescnum".

Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2014-02-07 09:16:26 -05:00
Aaron Wu
819ca38fa7 blackfin: Initialize the EMAC VLAN with proper default value
EMAC_VLANx regs is not properly initiallized in u-boot, once it's overwrite in the
kernel when DSA enabled, hot reset will lead to bringing up EMAC fail in u-boot.

Signed-off-by: Aaron Wu <Aaron.Wu@analog.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2014-02-07 11:18:06 +08:00
Marek Vasut
0b2d3f209a ARM: NET: Remove the IXP NPE ethernet driver
This driver is no longer used, remove it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
2014-02-06 02:51:52 +01:00
Tom Rini
f763be224f Merge branch 'net' of git://www.denx.de/git/u-boot-microblaze 2014-02-04 11:51:20 -05:00
Michal Simek
6f9b93723a net: axi_emac: Check if phy was correctly detected
As tsec and fm drivers checking phydev->link
ensure that u-boot don't try access device if link is not ready.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-04 16:42:45 +01:00
Prabhakar Kushwaha
5b7672fc49 boards/t1040qds: Adds ethernet support for T1040
Enable entherent for T1040QDS. It enables FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5
    Define MDIO related configs
    Added eth.c file
    Update t1040.c to support RGMII and SGMII
    Update t1040qds.c to support ethernet
    Define the PHY address

Signed-off-by: Arpit Goel <B44344@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: remove dash from commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-03 08:38:48 -08:00
Masahiro Yamada
4d764244bd drivers: delete unused header files
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-01-24 16:59:07 -05:00
Shengzhou Liu
4399434fef net/fm: revert commit 732dfe090d
This patch reverts patch 'add ft_fixup_xgec to support 3rd and 4th 10GEC'.
When dual-role MAC acts as 10G,it still uses fsl,fman-port-1g-rx/tx as before.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2014-01-21 14:05:52 -08:00
Shengzhou Liu
1576b558b9 powerpc/t2080qds: some update for t2080qds
- add more serdes protocols support.
- fix some serdes lanes route.
- fix SGMII doesn't work and incorrect mdio display for XFI when serdes 0x6d.
- correct boot location info for SD/SPI boot.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-21 13:37:41 -08:00
Michal Simek
4ed4aa20de net: gem: Check if phy was correctly detected
As tsec and fm drivers checking phydev->link
ensure that u-boot don't try access device if link is not ready.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-01-21 16:07:10 +01:00
Fabio Estevam
f66e3ded61 net: phy: atheros: Fix the masks for AR8031/8035
Use the same masks as used in the kernel:
https://git.kernel.org/cgit/linux/kernel/git/stable/linux-stable.git/tree/drivers/net/phy/at803x.c?id=refs/tags/v3.12.6

With such changes Ethernet is functional on hummingboard solo.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Marek Vasut <marex@denx.de>
Patch: 306640
2014-01-14 14:00:41 -06:00
Tom Rini
7f673c99c2 Merge branch 'master' of git://git.denx.de/u-boot-arm
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.

Conflicts:
	include/configs/exynos5250-dt.h

Signed-off-by: Tom Rini <trini@ti.com>
2014-01-10 10:56:00 -05:00
Albert ARIBAUD
a891601ce5 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Conflicts:
	include/micrel.h

The conflict above was trivial, caused by four lines being
added in both branches with different whitepace.
2014-01-06 08:49:58 +01:00
Yoshihiro Shimoda
3067f81f16 net: sh-eth: add support for SH7753
SH7753 has two fast ethernet controllers and two gigabit ethernet
controllers. It is similar to SH7757.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2013-12-18 16:49:45 +09:00
Shengzhou Liu
732dfe090d net/fman: add ft_fixup_xgec to support 3rd and 4th 10GEC
As mEMAC1 and mEMAC2 are dual-role MACs, which are used as 1G or 10G MAC.
So we update dynamically 'cell-index' to '2' and '3' for 10GEC3 and 10GEC4.
Also change 'fsl,fman-port-1g-rx' to 'fsl,fman-port-10g-rx', ditto for Tx.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-12-11 11:12:20 -08:00
Albert ARIBAUD
f15ea6e1d6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/armv7/rmobile/Makefile
	doc/README.scrapyard

Needed manual fix:
	arch/arm/cpu/armv7/omap-common/Makefile
	board/compulab/cm_t335/u-boot.lds
2013-12-10 22:23:59 +01:00
Vladimir Koutny
74007b8519 am335x: cpsw: optimize cpsw_recv to increase network performance
In 48ec5291, only TX path was optimized; this does the same also for RX
path. This results in huge increase of TFTP throughput on custom am3352
board (from 312KiB/s to 1.8MiB/s) and eliminates occasional transfer
timeouts.

Signed-off-by: Vladimir Koutny <vladimir.koutny@streamunlimited.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Tom Rini <trini@ti.com>
2013-12-04 11:41:13 -05:00
Tom Rini
77fdd6d1eb Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2013-12-02 08:38:28 -05:00
Shengzhou Liu
629d6b32d6 powerpc/mpc85xx: Add T2080/T2081 SoC support
Add support for Freescale T2080/T2081 SoC.

T2080 includes the following functions and features:
- Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz
- 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- Hierarchical interconnect fabric
- One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- 16 SerDes lanes up to 10.3125 GHz
- 8 mEMACs for network interfaces (four 1Gbps MACs and four 10Gbps/1Gbps MACs)
- High-speed peripheral interfaces
  - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
  - Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- Additional peripheral interfaces
  - Two serial ATA (SATA 2.0) controllers
  - Two high-speed USB 2.0 controllers with integrated PHY
  - Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC)
  - Enhanced serial peripheral interface (eSPI)
  - Four I2C controllers
  - Four 2-pin UARTs or two 4-pin UARTs
  - Integrated Flash Controller supporting NAND and NOR flash
- Three eight-channel DMA engines
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0

Differences between T2080 and T2081:
  Feature               T2080 T2081
  1G Ethernet numbers:  8     6
  10G Ethernet numbers: 4     2
  SerDes lanes:         16    8
  Serial RapidIO,RMan:  2     no
  SATA Controller:      2     no
  Aurora:               yes   no
  SoC Package:          896-pins 780-pins

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-11-25 11:44:25 -08:00
Shengzhou Liu
82a55c1ef8 net/fman: Add support for 10GEC3 and 10GEC4
There are more than two 10GEC in single FMAN in some SoCs(e.g. T2080).
This patch adds support for 10GEC3 and 10GEC4.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2013-11-25 11:43:47 -08:00
Tom Rini
1a1326d2da Merge branch 'master' of git://git.denx.de/u-boot-net 2013-11-25 10:42:19 -05:00
Masahiro Yamada
3c6dc17eae drivers: delete unnecessary HOSTCFLAGS
HOSTCFLAGS is meaningless because no host programs
are compiled there.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-25 10:41:54 -05:00
Thierry Reding
2287286be4 net: rtl8169: Add support for RTL8168d/8111d
This chip is compatible with the existing driver, except that it uses
BAR2 instead of BAR1 for the I/O memory region. Using this patch I can
use the PCIe ethernet interface on the CompuLab Trimslice to boot from
the network.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276477
2013-11-22 17:03:21 -06:00
Thierry Reding
22ece0e2e2 net: rtl8169: Improve cache maintenance
Instead of directly calling the low-level invalidate_dcache_range() and
flush_cache() functions, provide thin wrappers that take into account
alignment requirements.

While at it, fix a case where the cache was flushed but should have been
invalidated, two cases where the buffer data was flushed instead of the
descriptor and a missing cache invalidation before reading the packet
data that the NIC just wrote to memory.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276474
2013-11-22 17:03:21 -06:00
Srikanth Thokala
a5144237ac net: zynq_gem: Add d-cache support
Added d-cache support for zynq_gem.c,
Observed a difference of +0.8 MiB/s when downloading
a file of size of 3007944Bytes.

With d-cache OFF:
----------------
Filename 'uImage'.
Load address: 0x800
Loading: #################################################################
         #################################################################
         #################################################################
         ##########
         1.3 MiB/s
done
Bytes transferred = 3007944 (2de5c8 hex)

With d-cache ON:
---------------
Filename 'uImage'.
Load address: 0x800
Loading: #################################################################
         #################################################################
         #################################################################
         ##########
         2.1 MiB/s
done
Bytes transferred = 3007944 (2de5c8 hex)

Changes on zynq_gem for d-cache support:
- Tx and Rx buffers are cache-aligned
- Updated logic for invalidating Rx buffers and flushing Tx buffers.
- Tx and Rx BD's are allocated from non-cacheable region.
  (When BDs are cached, we don't see a consistent link)
- Use TX BD status intead of txsr status checks.

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-11-22 17:03:20 -06:00
David Dueck
f27f3b5266 phy: Use general phy code for smsc lan8720a
Signed-off-by: David Dueck <davidcdueck@googlemail.com>
2013-11-22 17:03:20 -06:00
David Dueck
3a530d1b3e phy: Use supported field during autonegotiation
The current code incorrectly detects gigabit capabilities for some
100Mbit/s phys. (lan8720a)

Signed-off-by: David Dueck <davidcdueck@googlemail.com>
2013-11-22 17:03:20 -06:00
Andrew Ruder
c583ee16cb net: dm9000: random mac address support
When an unprogrammed EEPROM is attached to a dm9000, the dm9000 will
come up with a invalid MAC address of ff:ff:ff:ff:ff:ff.  Add code that
gets enabled if CONFIG_RANDOM_MACADDR is enabled that generates a random
(and valid) locally administered MAC address that allows the system to
network boot until a real MAC address can be configured.

Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
2013-11-22 17:03:19 -06:00
Rojhalat Ibrahim
8712adfd05 drivers/net/e1000: Introduce CONFIG_E1000_NO_NVM
The e1000 driver expects to always have some kind of non-volatile memory
attached directly to the ethernet controller chip. This means that I would
have to add an additional separate flash chip to my custom board just to
store essentially the MAC address. Since I don't want to do that, this patch
introduces a new config option CONFIG_E1000_NO_NVM. If defined it disables
all accesses to the NVM. I have tested the patch with a 82574 controller.

Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
2013-11-22 17:03:19 -06:00
Fabio Estevam
e003ba5bfc net: phy: atheros: Fix masks for AR8035 and AR8021
The masks were ignoring the last 4 bits which didn't allow detection differences
between the ar8031 and ar8035.

Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Patch: 288018
2013-11-22 17:03:18 -06:00
Chunhe Lan
3177457853 net/phy: Fix the phy id mask of AR8031
The both AR8031 and AR8035 belong to Atheros 803x serial PHY.
So the phy id mask of AR8031 is the same to the phy id mask
of AR8035. The right mask value is 0x4fffff.

This patch has been tested on the P1010 and P1023.

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Patch: 287748
2013-11-22 17:03:18 -06:00
Claudiu Manoil
b1690bc39c net: tsec: Fix mac addr setup portability, cleanup
Fix the 32-bit memory access that is not "endianess safe",
i.e. not giving the desired byte layout for LE cpus:
tempval = *((uint *) (tmpbuf + 4)), where 'char tmpbuf[]'.

Free the stack from rendundant local vars:
tmpbuf[] and i.

Use a portable type (u32) for the 32bit tsec register value
holder: tempval.

Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
2013-11-22 17:03:17 -06:00
Claudiu Manoil
82ef75ca5c net: tsec: Use portable regs type (uint->u32)
Use cross arch portable u32 instead of uint for the
tsec registers.  Remove the typedefs for the register
struct definitions in the process.  Fix long lines.

Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
2013-11-22 17:03:17 -06:00
Claudiu Manoil
9c9141fd04 net: tsec: Use portable types and accessors for BDs
Currently, the buffer descriptor (BD) fields cannot be
correctly accessed by a little endian processor.  This
patch fixes the issue by making the access of BDs to be
portable among different cpu architectures.

Use portable data types for the Rx/Tx buffer descriptor
fields.  Use portable I/O accessors to insure that the
big endian BDs are correctly accessed by little endian
cpus too, and to insure proper sync with the H/W.
Removed the redundant RTXBD "volatile" type, as proper
synchronization around BD data accesses is provided by
the I/O accessors now.
The "sparse" tool was also used to verify the correctness
of these changes.

Cc: Scott Wood <scottwood@freescale.com>

Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
2013-11-22 17:03:16 -06:00
Claudiu Manoil
18b338fb34 net: tsec: Fix CamelCase issues around BD code
Fix bufPtr and the rxIdx/ txIdx occurrences to
solve the related checkpatch warnings for the
coming patches.

Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
2013-11-22 17:03:16 -06:00
Claudiu Manoil
5be00a0164 net: fsl_mdio: Fix warnings for __iomem pointers
Add the __iomem address space marker for the tsec pointers
to struct tsec_mii_mng memory mapped register regions.
This solves the sparse warnings for mixig normal pointers with
__iomem pointers for tsec. E.g.:

fsl_mdio.c:34:19: warning: incorrect type in argument 1 (different
address spaces)
fsl_mdio.c:34:19:    expected unsigned int volatile [noderef]
<asn:2>*addr
fsl_mdio.c:34:19:    got unsigned int *<noident>
[...]

tsec.c:91:35: warning: incorrect type in argument 1 (different address
spaces)
tsec.c:91:35:    expected struct tsec_mii_mng *phyregs
tsec.c:91:35:    got struct tsec_mii_mng [noderef] <asn:2>*phyregs_sgmii
[...]

tsec.c:680:19: warning: incorrect type in assignment (different address
spaces)
tsec.c:680:19:    expected struct tsec_mii_mng *regs
tsec.c:680:19:    got struct tsec_mii_mng [noderef] <asn:2>*<noident>
[...]

Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
2013-11-22 17:03:15 -06:00
Claudiu Manoil
aec84bf671 net: tsec: Cleanup tsec regs init and fix __iomem warns
Remove tsec_t typedef.  Define macros as getters of
tsec and mdio register memory regions, for consistent
initialization of various 'regs' fields and also to
manage overly long initialization lines.
Use the __iomem address space marker to address sparse
warnings in tsec.c where IO accessors are used, like:

tsec.c:394:19: warning: incorrect type in argument 1 (different
address spaces)
tsec.c:394:19:    expected unsigned int volatile [noderef]
<asn:2>*addr
tsec.c:394:19:    got unsigned int *<noident>
[...]

Add the __iomem address space marker for the tsec pointers
to struct tsec_mii_mng memory mapped register regions.
This solves the sparse warnings for mixig normal pointers
with __iomem pointers for tsec.

Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
2013-11-22 17:03:15 -06:00
Claudiu Manoil
b200204e8e net: tsec: Fix priv pointer in tsec_mcast_addr()
Access to privlist[1] (hardcoded referece to the 2nd tsec's
priv area) is neither correct nor does it make sense in the
current context.  Each tsec dev has access to its own priv
instance only, and hence to its own set of group address
registers (GADDR) to filter multicast addresses.

This fix leads to removal of the unused (faulty) privlist[]
and related global static vars.  Note that mcast() can be
called only after eth_device allocation and init, and hence
after priv area allocation, so dev->priv is correctly
initialized upon mcast() call.

Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Patch: 278990
2013-11-22 17:02:56 -06:00
Claudiu Manoil
876d4515e3 net: tsec: Fix and cleanup tsec_mcast_addr()
There are several implementation issues for tsec_mcast_addr()
addressed by this patch:
* unmanaged, not portable r/w access to registers; fixed with
setbits_be32()/ clrbits_be32()
* use of volatile pointers
* unnecessary forced cast to u8 for the ether_crc() result
* removed redundant parens
* corrected some comment slips

Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Patch: 279000
2013-11-22 16:57:47 -06:00
Claudiu Manoil
9c4cffacec net: Fix mcast function pointer prototype
This fixes the following compiler warnings when activating
CONFIG_MCAST_TFTP:

tsec.c: In function 'tsec_mcast_addr':
tsec.c:130:2: warning: passing argument 2 of 'ether_crc' makes pointer
from integer without a cast [enabled by default]
In file included from /work/u-boot-net/include/common.h:874:0,
                 from tsec.c:15:
/work/u-boot-net/include/net.h:189:5: note: expected 'const unsigned
char *' but argument is of type 'u8'
tsec.c: In function 'tsec_initialize':
tsec.c:646:13: warning: assignment from incompatible pointer type
[enabled by default]
eth.c: In function 'eth_mcast_join':
eth.c:358:2: warning: passing argument 2 of 'eth_current->mcast' makes
integer from pointer without a cast [enabled by default]
eth.c:358:2: note: expected 'u32' but argument is of type 'u8 *'

In the eth_mcast_join() implementation, eth_current->mcast()
takes a u8 pointer to the multicast mac address and not a ip
address value as implied by its prototype.

Fix parameter type mismatch for tsec_macst_addr() (tsec.c):
ether_crc() takes a u8 pointer not a u8 value.
mcast() is given a u8 pointer to the multicats mac address.
Update parameter type for the rest of mcast() instances.

Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Patch: 278989
2013-11-22 16:57:13 -06:00
Alexey Brodkin
ed102be70f net: designware: Fix alignment of buffer descriptors
It's important that buffer descriptors are aligned in accordance to GMAC
data bus width (32/64/128-bit). It's safe to align to 128-bit (16-bytes)
for every bus width type.

If buffer descriptor is improperly aligned GMAC discards lower bits of
provided address and as a result reads from improper location that
doesn't match expected fields.

Commit ef76025a99 "net: Multiple
updates/enhancements to designware.c" introduced another structure
member "link_printed" right before buffer descriptors while "padding"
member was left untouched. This together with alignment of structure
itself to 16-byte boundary forces buffer descriptoprs always to be
4-byte aligned that causes driver complete disfunction if GMAC bus width
is 64 or 128-bit.

Proposed change makes sure all buffer descriptors are 16-byte (128-bit)
aligned.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Patch: 277902
2013-11-22 16:50:55 -06:00
Alexey Brodkin
227ad7b2b6 net: designware: Respect "bus mode" register contents on SW reset
"bus mode" register contains lots of fields and some of them don't
expect to be written with 0 (zero). So since we're only interested in
resetting MAC (which is done with setting the least significant bit of
this register with "0") I believe it's better to modify only 1 bit of
the register.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Vipin Kumar <vipin.kumar@st.com>
Patch: 277864
2013-11-22 16:50:54 -06:00
Nobuhiro Iwamatsu
47ce889048 net: sh-eth: Add support R8A7791
R8A7791 has the same sh-ether IP core as other SH/rmobile.
This patch adds support of R8A7791.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Joe Hershberger <joe.hershberger@gmail.com>
2013-11-22 16:50:54 -06:00
Heiko Schocher
dfcaa61c33 net, phy: fix AR8031 phy_mask
AR8035 driver will be never applied because of wrong mask for
AR8031 driver. Fix this.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reported-by: Pavel Nakonechny <pavel.nakonechny@skitlab.ru>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Patch: 276944
2013-11-22 16:50:54 -06:00
Thierry Reding
65a6691ed3 net: rtl8169: Add support for RTL8168evl/8111evl
This chip is compatible with other RTL8168 chips and can be found on the
NVIDIA Cardhu and Beaver boards.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276475
2013-11-22 16:50:53 -06:00
Thierry Reding
7a36b9c1ac net: rtl8169: Fix format string
currticks() is defined as get_timer(0), which returns an unsigned long,
so use %lu instead of %d to print the result.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276473
2013-11-22 16:50:53 -06:00
Stefano Babic
9ced16fefa net: add function to read/write extended registers in Micrel Phy
Signed-off-by: Stefano Babic <sbabic@denx.de>
2013-11-22 16:50:52 -06:00
Stefano Babic
e8194d58bd net: fix mask for phy Micrel KSZ9031
Signed-off-by: Stefano Babic <sbabic@denx.de>
2013-11-22 16:50:51 -06:00
Bhupesh Sharma
4220504767 net/phy: realtek: Fix the PHY ID mask to ensure the correct Realtek PHY is detected
The 'get_phy_driver' code in 'drivers/net/phy/phy.c' uses the following
method to determine which driver is to be loaded for a particular PHY
module:

list_for_each(entry, &phy_drivers) {
	drv = list_entry(entry, struct phy_driver, list);
	if ((drv->uid & drv->mask) == (phy_id & drv->mask))
		return drv;
}

This means that a drv->mask of 0xfffff0 will return incorrect phy driver
for the logic above, even if the drv->uid is anything other than
something ending with a 0x0.

For e.g. if the RTL8211E drv->uid is 0x1cc915 and drv->mask is 0xffffff
and the RTL8211B drv->uid is 0x1cc910 and drv->mask is 0xffffff0, then
the phy driver selected will always be RTL8211B even though the
underlying phy connected on the board is a 8211E module.

This patch fixes this issue.

Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
2013-11-22 16:50:51 -06:00
Arpit Goel
e97a78cfed net: phy/vitesse: Add support for VSC8514 phy module
This patch adds support for VSC8514 PHY module which can be
found on Freescale's T1040RDB boards.

Signed-off-by: Arpit Goel <B44344@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
2013-11-22 16:50:50 -06:00
Nobuhiro Iwamatsu
8707678cc4 net: sh-eth: Add support R8A7790
R8A7790 has the same sh-ether IP core as other SH/rmobile.
This patch adds support of R8A7790.

Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-11-22 16:50:50 -06:00
Nobuhiro Iwamatsu
92f0713408 net: sh-eth: Add invalidate cache control for rmobile (ARM SoC)
The sh-eth of rmobile needs to use invalidate_cache* function.
This patch adds invalidate_cache* function.

Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Patch: 268948
2013-11-22 16:50:49 -06:00
Nobuhiro Iwamatsu
f8b7507d41 net: sh-eth: Add control for padding size of packet descriptor
sh-eth can change the alignment size of a packet descriptor according to BUS
size. This patch adds this function.

Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-11-22 16:50:49 -06:00
Nobuhiro Iwamatsu
870cc23f07 net: sh-eth: Change cache API of SH
The cache API of SH was changed from dcache_wback_range to flush_dcache_range.
sh-eth uses dcache_wback_range. This patch changes to flush_dcache_range.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-11-22 16:50:49 -06:00
Sascha Silbe
0611c6017c NET: mvgbe: avoid unused variable warning when used without phylib support
Avoid a recently introduced unused variable warning for boards that
use mvgbe but not phylib.

Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
Patch: 266334
2013-11-22 16:50:34 -06:00
Shengzhou Liu
626ee1e32e phylib: update atheros ar803x phy
As AR8031 and AR8033 have same PHY ID 0x4dd074, they use the
common driver. Currently AR8031_driver didn't work for AR8033,
hence updated it to have it work on AR8031/AR8033.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2013-11-22 14:39:54 -06:00
Marek Vasut
79e5f27b09 Net: FEC: Fix huge memory leak
The fec_halt() never free'd both RX and TX DMA descriptors that
were allocated in fec_init(), nor did it free the RX buffers.
Rework the FEC driver so that these descriptors and buffers are
allocated only once in fec_probe().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-11-21 16:32:29 +01:00
Masahiro Yamada
fdd91faef9 drivers/net/npe: descend only when CONFIG_IXP4XX_NPE=y
CONFIG_IXP4XX_NPE is defined only for CPU ixp.
It is not necessary to filter by CPU ixp.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-17 14:11:32 -05:00
Masahiro Yamada
fc9ac3565a drivers/net/fm: descend only when CONFIG_FMAN_ENET=y
CONFIG_FMAN_ENET is defined only for CPU mpc85xx.
We do not need to filter by CPU mpc85xx.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-17 14:11:31 -05:00
Andreas Bießmann
1bcdde2499 net: remove unused CONFIG_AT91_LEGACY
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-13 22:13:32 +01:00
Priyanka Jain
2967af6816 powerpc/t1040: Update defines to support T1040SoC personalities
T1040 Soc has four personalities:
-T1040 (4 cores with L2 switch)
-T1042:Reduced personality of T1040 without L2 switch
-T1020:Reduced personality of T1040 with less cores(2 cores)
-T1022:Reduced personality of T1040 with 2 cores and without L2 switch

Update defines in arch/powerpc header files, Makefiles and in
driver/net/fm/Makefile to support all T1040 personalities

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: fixed Makefiles]
Acked-by: York Sun <yorksun@freescale.com>
2013-11-13 12:41:08 -08:00
Wolfgang Denk
649acfe149 MPC824x: remove obsolete "PN62" board
The MPC824x processors have long reached EOL, and the PN62 board has
not seen any board-specific updates for more than a decade.  It is now
causing build issues.  Instead of wasting time on things nobody is
interested in any more, we rather drop this board.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
cc: Tom Rini <trini@ti.com>
2013-11-11 14:46:24 -05:00
Tom Rini
60390d70be Merge branch 'master' of git://git.denx.de/u-boot-mips 2013-11-11 09:40:34 -05:00
Albert ARIBAUD
85b8c5c4bf Merge branch 'iu-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h
2013-11-09 22:59:47 +01:00
Paul Burton
62715a2c57 pcnet: enable the NOUFLO feature
On relatively slow boards (such as the MIPS Malta with an FPGA core
card) it can be extremely common for transmits to underflow - to the
point where it appears they simply do not work at all. Setting the
NOUFLO bit causes the ethernet controller to not begin transmission on
the wire until a transmit start point is reached. Setting that transmit
start point to the full packet will cause the controller to only
transmit the packet once it has buffered it entirely thus preventing any
transmit underflows from occuring and allowing the controller to
function on slower boards.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09 17:21:01 +01:00
Paul Burton
f3ac866c78 pcnet: add cache flushing & invalidation
Ensure that the view of memory from the CPU & the ethernet controller is
coherent at the various points where they exchange data. This prevents
stale data from being transmitted or received, and prevents the driver
from getting stuck waiting for the ethernet controller to update
descriptors when in reality it has but the old values are being read
from cache.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09 17:21:01 +01:00
Paul Burton
a95400411b pcnet: s/le16_to_cpu/cpu_to_le16/ in pcnet_send
This should cause no change to the generated code, but is semantically
correct.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09 17:21:01 +01:00
Paul Burton
6011dabd0a pcnet: code style cleanup
Fix up the code to match Documentation/CodingStyle. This is mostly
removing extraneous spaces.

No functional change is intended.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09 17:21:01 +01:00
Suriyan Ramasami
efd9bb9c02 netconsole loses 2nd character of input
Netconsole loses the second character when used as input by
either setenv stdin nc or setenv stdin serial,nc if using CONSOLE_CONSOLE_MUX

Before a nc_send_packet() to echo the input, a check is done to see if
nc_ether is valid. If its not, it waits for an arp request and then sends
the packet (which contains the first character of line to be displayed as
output). As part of reaping the arp request, the second character is consumed.
We protect this by making the call to NetLoop(NETCONS) between
input_recursion.

Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2013-11-08 15:25:14 -05:00
Masahiro Yamada
0f0f75774e cosmetic: remove empty lines at the top of file
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-08 09:41:37 -05:00
Bo Shen
32e4f6bf2e net: macb: get DMA bus width from design config register
Get DMA bus width from design config register

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04 20:32:31 +01:00
Masahiro Yamada
e32459e24a drivers: net: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 13:22:13 -04:00
Valentin Longchamp
f51d3b71d4 net/fman: add a fm_enable_port function
This can be useful if one wants to disable an interface in u-boot
because u-boot should not manage it but then later reenable it for FDT
fixing or if the kernel uses this interface.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix conflict in fm_eth.h]
Acked-by: York Sun <yorksun@freescale.com>
2013-10-24 09:35:59 -07:00
Prabhakar Kushwaha
7d436078fe powerpc/t1040qds: Add T1040QDS board
T1040QDS is a high-performance computing evaluation, development and
test platform supporting the T1040 QorIQ Power Architecture™ processor.

 T1040QDS board Overview
 -----------------------
 - Four e5500 cores, each with a private 256 KB L2 cache
 - 256 KB shared L3 CoreNet platform cache (CPC)
 - Interconnect CoreNet platform
 - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
   support
 - Data Path Acceleration Architecture (DPAA) incorporating acceleration
 for the following functions:
    -  Packet parsing, classification, and distribution
    -  Queue management for scheduling, packet sequencing, and congestion
    	management
    -  Cryptography Acceleration
    - RegEx Pattern Matching Acceleration
    - IEEE Std 1588 support
    - Hardware buffer management for buffer allocation and deallocation
 - Ethernet interfaces
    - Integrated 8-port Gigabit Ethernet switch
    - Four 1 Gbps Ethernet controllers
 - SERDES Connections, 8 lanes supporting:
      — PCI Express: supporting Gen 1 and Gen 2;
      — SGMII
      — QSGMII
      — SATA 2.0
      — Aurora debug with dedicated connectors
 - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
   Interleaving
 -IFC/Local Bus
     - NAND flash: 8-bit, async, up to 2GB.
     - NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
     - GASIC: Simple (minimal) target within Qixis FPGA
     - PromJET rapid memory download support
 - Ethernet
     - Two on-board RGMII 10/100/1G ethernet ports.
     - PHY #0 remains powered up during deep-sleep
 - QIXIS System Logic FPGA
 - Clocks
     - System and DDR clock (SYSCLK, “DDRCLK”)
     - SERDES clocks
 - Power Supplies
 - Video
     - DIU supports video at up to 1280x1024x32bpp
 - USB
     - Supports two USB 2.0 ports with integrated PHYs
     — Two type A ports with 5V@1.5A per port.
     — Second port can be converted to OTG mini-AB
 - SDHC
     - SDHC port connects directly to an adapter card slot, featuring:
     - Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC
     — Supporting eMMC memory devices
 - SPI
    -  On-board support of 3 different devices and sizes
 - Other IO
    - Two Serial ports
    - ProfiBus port
    - Four I2C ports

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: fix conflict in boards.cfg]
Acked-by-by: York Sun <yorksun@freescale.com>
2013-10-16 16:15:16 -07:00
Zhao Qiang
ffee1dde3c SGMII:fix PHY addresses for QSGMII Riser Card working in SGMII mode
Fix PHY addresses for QSGMII Riser Card working in
SGMII mode on board P3041/P5020/P4080/P5040/B4860.

QSGMII Riser Card can work in SGMII mode, but
having the different PHY addresses.
So the following steps should be done:
	1. Confirm whether QSGMII Riser Card is used.
	2. If yes, set the proper PHY address.
Generally, the function is_qsgmii_riser_card() is
for step 1, and set_sgmii_phy() for step 2.

However, there are still some special situations,
take P5040 and B4860 as examples, the PHY addresses
need to be changed when serdes protocol is changed,
so it is necessary to confirm the protocol before
setting PHY addresses.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
2013-10-16 16:13:11 -07:00
Wolfgang Denk
93e1459641 Coding Style cleanup: replace leading SPACEs by TABs
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Drop changes for PEP 4 following python tools]
Signed-off-by: Tom Rini <trini@ti.com>
2013-10-14 16:06:54 -04:00
Wolfgang Denk
3765b3e7bd Coding Style cleanup: remove trailing white space
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:53 -04:00
Tom Rini
6297872cd5 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-10-02 11:45:22 -04:00
Albert ARIBAUD
f04c537629 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-10-02 14:53:27 +02:00
Heiko Schocher
93ff255298 net, phy, cpsw: fix NULL pointer deference
if phy_connect() did not find a phy, phydev is NULL and
following code in cpsw_phy_init() crashes. Fix this.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-09-20 16:57:40 -04:00
Fabio Estevam
fd37f195ca net: fec_mxc: Fix timeouts during tftp transfer
Performing tftp transfers on mx28 results in random timeouts.

Hector Palacios and Robert Hodaszi analyzed the root cause being related to the
wrong alignment of the 'buff' buffer inside fec_recv().

Benoît Thébaudeau provided an excellent analysis of the alignment bug that is
present on older versions, such as GCC 4.5.4:

http://marc.info/?l=u-boot&m=137942904906131&w=2

Use ALLOC_CACHE_ALIGN_BUFFER() to avoid alignment issues from older GCC
versions.

Reported-by: Hector Palacios <hector.palacios@digi.com>
Tested-by: Oliver Metz <oliver@freetz.org>
Tested-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
2013-09-20 17:55:37 +02:00
Fabio Estevam
7df51fd8be net: fec_mxc: Add support for mx6 solo-lite
Similarly as mx25 and mx53, mx6solo-lite needs to setup the MII gasket for RMII
mode.

Add support for mx6solo-lite.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20 17:55:36 +02:00
Wolfgang Denk
1b387ef55c SPDX: fix IBM-pibs license identifier
The SPDX License List version 1.19 now contains an official entry for
the IBM-pibs license.  However, instead of our suggestion "ibm-pibs",
the SPDX License List uses "IBM-pibs", with the following rationale:
"The reason being that all other SPDX License List short identifiers
tend towards using capital letters unless spelling a word.  I'd prefer
to be consistent to this end".

Change the license IDs to use the official name.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-09-20 10:30:54 -04:00
Robert P. J. Day
1bce2aeb6f Cosmetic: Fix a number of typos, no functional changes.
Fix various misspellings of things like "environment", "kernel",
"default" and "volatile", and throw in a couple grammar fixes.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2013-09-20 10:30:54 -04:00
Albert ARIBAUD
19d829fa60 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Conflicts:
	drivers/serial/serial.c

The conflict above was a trivial case of adding one init
function in each branch, and manually resolved in merge.
2013-09-05 11:15:26 +02:00
Albert ARIBAUD
4eef93da26 Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master' 2013-09-04 11:50:25 +02:00
Bo Shen
8314ccd8d4 net: macb: fix the following building warning
fix the following building warning
---8>---
macb.c: In function 'macb_init':
macb.c:400:14: warning: 'phydev' may be used uninitialized in this function
macb.c:377:21: note: 'phydev' was declared here
---<8---

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22 16:49:29 +02:00
Eric Nelson
ddb636bd66 fec_mxc: set ethaddr if fuses burned and not previously set
Without this change, the following message is generated:
	Warning: FEC using MAC address from net device

See doc/README.enetaddr for details.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-08-21 19:20:28 +02:00
Shaohui Xie
1c68d01eea powerpc/t4240: add QSGMII interface support
Also some fix for QSGMII.
1. fix QSGMII configure of Serdes2.
2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN.
3. fix dtb for QSGMII interface.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-08-20 10:46:48 -07:00
Wolfgang Denk
cb3761ea99 SPDX-License-Identifier: convert BSD-3-Clause files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini Don't remove some copyrights by accident]
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-19 15:45:35 -04:00
Wolfgang Denk
46263f2de4 SPDX-License-Identifier: convert PIBS licensed files
This commit adapts the files that were derived from PIBS (PowerPC
Initialization and Boot Software) codeto using SPDX License
Identifiers.

So far, SPDX has not assigned an official License ID for the PIBS
license yet, so this should be considered preliminary.

Note that the following files contained incorrect license information:

	arch/powerpc/cpu/ppc4xx/4xx_uart.c
	arch/powerpc/cpu/ppc4xx/start.S
	arch/powerpc/include/asm/ppc440.h

These files included, in addition to the GPL-2.0 / ibm-pibs dual
license as inherited from PIBS, a GPL-2.0+ license header which was
obviously incorrect.  This has been removed.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>

Conflicts:
	Licenses/README
Acked-by: Stefan Roese <sr@denx.de>
2013-08-19 15:34:14 -04:00
Kuo-Jung Su
0628cb2659 net: ftmac110: Update tx/rx descriptor format
1. Reformat tx/rx descriptor as an uniform struct.
2. Replace uint32_t[2] with uint64_t for descriptor control.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Joe Hershberger <joe.hershberger@gmail.com>
2013-08-19 12:34:21 -05:00
Kuo-Jung Su
4b7be19920 net: ftmac110: struct ftmac110_regs __iomem * -> struct ftmac110_regs *
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Joe Hershberger <joe.hershberger@gmail.com>
2013-08-19 12:34:21 -05:00
Kuo-Jung Su
102a8cd3ed net: ftmac110: Update license statement
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Joe Hershberger <joe.hershberger@gmail.com>
2013-08-19 12:34:20 -05:00
Bhupesh Sharma
c624d168bf net: phy/realtek: Add support for RTL8211DN and RTL8211E phy modules
This patch adds support for Realtek PHY modules RTL8211DN and
RTL8211E (variants: RTL8211E-VB-CG, RTL8211E-VL-CG, RTL8211EG-VB-CG),
which can be found on Freescale's T1040RDB boards.

To make the driver more generic across 8211 family, a generic name 8211x
is added for macros and function names.

Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-08-19 12:34:19 -05:00
Axel Lin
a62cd29c98 net: Use ARRAY_SIZE at appropriate places
Use ARRAY_SIZE instead of having similar implementation in each drivers.
The NUMELEMS defined in drivers/net/npe/include/IxOsalTypes.h is not used
at all, so this patch removes it instead of converting it to use ARRAY_SIZE.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
2013-08-19 12:34:18 -05:00
Fabio Estevam
25634210af phy: smsc: LAN8710/8720 are not Gbit PHYs
LAN8710/8720 are 10/100 Mbps PHYs, so fix the '.features' field.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-08-19 12:34:18 -05:00
Tom Rini
e20cc2ca15 Merge branch 'master' of git://88.191.163.10/u-boot-arm
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.

Conflicts:
	arch/arm/include/asm/arch-am33xx/hardware.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-08-18 14:14:34 -04:00
York Sun
7adefb55ad drivers/fm: Fix compiling error if FW location is not defined
FMAN firmware can be in NOR flash, NAND flash, SPI flash, MMC or even
remote. In case none of them is defined, set it to null.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-09 12:41:38 -07:00
Heiko Schocher
f6d1f6e4a5 net, phy, cpsw: fix gigabit register access
accessing a lan9303 switch with the cpsw driver results in wrong
speed detection, as the switch sets the BMSR_ERCAP in BMSR
register, and follow read of the MII_STAT1000 register fails, as
the switch does not support it. Current code did not check,
if a phy_read() fails ... fix this.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30 09:21:42 -04:00