The base address of extended DDR does not change across the K3 family.
Setting this per SoC is not needed. Remove this definition to help
remove the last bits from K3 include/configs/*.h files.
Signed-off-by: Andrew Davis <afd@ti.com>
Updates as a result of TIFS core now reserving a virtual interrupt
for enabling interrupts between DM to TIFS core. Because of this
change other virtual interrupt counts decrease by one.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Share the MCU GPIO interrupts between A53 core and DM R5 core. Allocating
2 instances each to A53 and DM R5.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Update am62ax rm-cfg with allocation entries for C7x core. Following
updates are added for C7x:
- Share split BCDMA tx and rx channels between DM R5 and C7x
- Share rings for split BCDMA tx and rx channels between DM R5 and C7x
- Add Global events and Virtual interrupts for C7x
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
This file is common for all K3, move it out of board/ directory and
into mach-k3. As we need to change the path in k3-binman.dtsi let's
take this opportunity to switch to absolute paths which makes adding
non-TI boards (like Toradex Verdin) not need to override these paths.
Signed-off-by: Andrew Davis <afd@ti.com>
Simplify the way all MTD devices are parsed.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Since MTD devices are partioned, we got the following
error when command "dfu 0" is executed:
DFU alt info setting: done
ERROR: Too many arguments for nor0
ERROR: DFU entities configuration failed!
ERROR: (partition table does not match dfu_alt_info?)
Fixes: 31325e1b8b ("stm32mp1: dynamically build DFU_ALT_INFO")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
- Add TPM support for venice boards
- Add networking support for imx93-evk
- Enable TCP, IPv6, wget for DHCOM and Data Modul boards
- Enable fastboot support for Toradex boards
- Allow pico-imx7d to boot from SD
- Enable fastboot for beacon imx8m beacon boards, disabled
SYS_CONSOLE_IS_IN_ENV
- Fix mxsboot to prevent NAND blocks being reported as bad
- Add imx8mm PWM clock support
- Several devicetree syncs with the kernel
- Add support for i.MX8MP Polyhex Debix Model A SBC
- Reworked ddr_load_train_firmware() to get a 50ms boot time improvement
Technexion PICO-IMX7 SoM is supporting USDHC3 (eMMC or micro SD on SoM)
and USDHC1 (SD on carrier board) to use on any carrier board like
PICO-NYMPH. Based on the U-Boot version from Technexion it adds
baseboard SD card boot detect to able to boot from selected USDHC1
or USDHC3 boot devices.
Signed-off-by: Benjamin Szőke <egyszeregy@freemail.hu>
Tested-by: Fabio Estevam <festevam@gmail.com>
To quote the author:
It would be useful to be able to boot an OS when CONFIG_CMDLINE is
disabled. This could allow reduced code size.
Standard boot provides a way to handle programmatic boot, without
scripts, so such a feature is possible. The main impediment is the
inability to use the booting features of U-Boot without a command line.
So the solution is to avoid passing command arguments and the like to
code in boot/
A similar process has taken place with filesystems, for example, where
we have (somewhat) separate Kconfig options for the filesystem commands
and the filesystems themselves.
This series starts the process of refactoring the bootm logic so that
it can be called from standard boot without using the command line.
Mostly it removes the use of argc, argv and cmdtbl from the internal
logic.
Some limited tidy-up is included, but this is kept to smaller patches,
rather than trying to remove all #ifdefs etc. Some function comments
are added, however.
A simple programmatic boot is provided as a starting point.
This work will likely take many series, so this is just the start.
Size growth with this series for firefly-rk3288 (Thumb2) is:
arm: (for 1/1 boards) all +23.0 rodata -49.0 text +72.0
This should be removed by:
https://source.denx.de/u-boot/custodians/u-boot-dm/-/issues/11
but it is not included in this series as it is already large enough.
No functional change is intended in this series.
Changes in v3:
- Add a panic if programmatic boot fails
- Drop RFC tag
Changes in v2:
- Add new patch to adjust position of unmap_sysmem() in boot_get_kernel()
- Add new patch to obtain command arguments
- Fix 'boot_find_os' typo
- Pass in the command name
- Use the command table to provide the command name, instead of "bootm"
The U_BOOT_CMD_COMPLETE() macro has a semicolon at the end, perhaps
inadvertently. Some code has taken advantage of this.
Tidy this up by dropping the semicolon from the macro and adding it to
macro invocations as required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This commit adds support for Fastboot boot commands by checking both
CONFIG_CMD_USB_SDP and CONFIG_USB_FUNCTION_FASTBOOT. If either of these
configurations is set, it indicates that the board is in recovery mode
and can use either SDP or Fastboot.
The default option remains the SDP command, but if
CONFIG_CMD_FASTBOOT is set, it changes to 'fastboot usb 0' as
the boot command.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
With Ethernet DM in place, there is no longer the need for having
the board_phy_config() anymore.
Remove it.
Tested on imx7d-pico-pi board:
=> setenv autoload no
=> dhcp
BOOTP broadcast 1
*** Unhandled DHCP Option in OFFER/ACK: 42
DHCP client bound to address 192.168.0.138 (138 ms)
=> tftp zImage
Using ethernet@30be0000 device
TFTP from server 192.168.0.16; our IP address is 192.168.0.138
Filename 'zImage'.
Load address: 0x80800000
Loading: #################################################################
....
#################################################################
##########
4.3 MiB/s
done
Bytes transferred = 9034120 (89d988 hex)
Signed-off-by: Fabio Estevam <festevam@denx.de>
In order to use the generic "distro boot" using an extlinux.conf file,
the `fdtfile` environment variable is mandatory. This commit ensure this
variable is properly constructed based on the detected board revision.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
The address ariel.dalessandro@collabora.com is no longer working:
A message that you sent could not be delivered to one or more of its
recipients. This is a permanent error. The following address(es) failed:
ariel.dalessandro@collabora.com
host mx.collabora.co.uk [46.235.227.165]
SMTP error from remote mail server after RCPT TO:<ariel.dalessandro@collabora.com>:
550 5.1.1 <ariel.dalessandro@collabora.com>: Recipient address rejected:
undeliverable address: host mail.collabora.co.uk[46.235.227.172] said:
550 5.1.1 <ariel.dalessandro@collabora.com>: Recipient address rejected:
User unknown in local recipient table (in reply to RCPT TO command)
Remove this address from MAINTAINERS.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
With DM enabled, there is no need for board code to initialize
the FEC interface.
The ethernet PHYs on the symphony carrier board have a dedicated
crystal/oscillator. If the SOM has the EC configuration option
(onboard ethernet PHY), it also has a dedicated crystal/oscillator.
So in all cases, there is no need to enable the RGMII TX clk output.
This follows a similar change introduced by Fabio Estevam:
Link: https://lore.kernel.org/u-boot/20231019170441.1610453-1-festevam@gmail.com/
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
I would like to help maintaining the imx8mn_var_som symphony board.
Add myself to MAINTAINERS.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
With DM enabled, there is no need for board code to initialize
the Ethernet interfaces.
The RTL8211FDI Ethernet PHYs have 25MHz oscillator, so there is no
need to enable the RGMII TX clk output.
Also, there is no need for describing the deprecated phy-reset FEC
properties, nor passing reset properties to the EQOS interface in
u-boot.dtsi.
Remove all these unneeded pieces.
Tested both Ethernet interfaces after these changes.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
I would like to help maintaining the imx8mp_evk board.
Add myself to MAINTAINERS.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Currently, the imx8mp_evk uses the non-DM code to initialize the PMIC.
Convert to DM_PMIC, which is the recommended way to access the PMIC.
While at it, fix multi-line comments style.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add a common board_interface_eth_init() called by the DWC MAC driver to
setup the MAC <-> PHY interface according to the PHY mode obtained from
DT.
Remove the board-side configuration in the i.MX93 EVK files.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Sync the devicetree files used in the kernel for the imx8mm-phyboard-polis
with the corresponding devicetree files in U-Boot.
Replaced phycore-imx8mm.dts with kernel dts imx8mm-phyboard-polis-rdk.dts
Synced with kernel 6.5.0-rc1 commit
e752a4f9589c (arm64: dts: freescale: imx8mm-phyboard: Add I2C4 pinmuxing)
Signed-off-by: Cem Tenruh <c.tenruh@phytec.de>
Commit 0aea5dda29 ("ARM: dts: imx7d-sdb-u-boot: Fix usdhc1 UHS
operation") did a temporary workaround by addng the usdhc1 fix
inside the -u-boot.dtsi file.
The imx7d-sdb.dts from kernel 6.5-rc1 contains the proper UHS
fix, so sync the devicetree tree and remove the previous fix
from -u-boot.dtsi.
Also, adjust the PMIC node name inside pmic_get() to match
the devicetree update.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add support for the Polyhex Debix Model A SBC board.
It is an industrial grade single board computer based on
NXP's i.MX 8M Plus.
Currently supported interfaces are:
- Serial console
- Micro SD
- eQOS and FEC Ethernet
imx8mp-debix-model-a.dts is taken from Linux 6.3.
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
In case of A/B update systems there should be an option to load the same
binary/binaries to different location and they should work.
Before this patch boot.bin with U-Boot SPL can be added to whatever 32k
offset in SPI and SPL finds u-boot.itb at CONFIG_SYS_SPI_U_BOOT_OFFS
offset. In case of A/B update systems that means that SPL is at different
locations but it still points to the same u-boot.itb which is not correct.
That's why include multiboot value to offset calculation to be able to
point to image from the same base.
It doesn't affect any current system which starts from 0 offset.
This patch also change Kria defconfig which uses A/B setup. Partition
A starts at multiboot 64, partition B at multiboot 496.
And also print message about used SPI offset which is useful for all cases.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/93903a53ad9358ae69991558b787f574797effbe.1699619666.git.michal.simek@amd.com
Enable the initial kria SOM specific configurations like pinctrl,
pinconf etc. Also add the environment file.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231109042407.6123-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
To quote the author:
The show_board_info() function was adjusted to weak so that it could be
entirely replaced with a board-specific implementation.
The intended way for boards to provide their own information is via a
sysinfo driver. But currently there is no way to show anything other
than the model name.
This series adds support for showing a few more items, in a way that is
easy for boards to extend.
Since there is already a weak checkboard() function, we don't need to
have two levels of weak function here. So this series drops the weak
attribute from show_board_info()
Existing boards will see a slight change in output, in that the model
name will appear first, before any custom output. If that is a problem,
then the solution is to implement a sysinfo driver for the board.
Create a sysinfo driver to avoid needing a custom checkboard()
function. With this the following information is printed when booting
from coreboot under QEMU:
Model: Standard PC (i440FX + PIIX, 1996)
Manufacturer: QEMU
Prior-stage version: 4.21-885-g2a87ef1eca56
Prior-stage date: 11/11/2023
Signed-off-by: Simon Glass <sjg@chromium.org>
Boards can use a sysinfo driver if a particular model name is needed.
Update this board to use checkboard() directly, rather than having a
weak function laid on top of a weak function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Boards can use a sysinfo driver if a particular model name is needed.
Update this board to use checkboard() directly, rather than having a
weak function laid on top of a weak function.
Make all the checkboard() functions call the new tdx_checkboard() so
that the same information is displayed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Boards can use a sysinfo driver if a particular model name is needed.
Update this board to use checkboard() directly, rather than having a
weak function laid on top of a weak function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Boards can use a sysinfo driver if a particular model name is needed.
Update this board to use checkboard() directly, rather than having a
weak function laid on top of a weak function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
This enables UFS support for QEMU RISC-V 'virt' machine.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is a couple of issues related to SYS_CONFIG_NAME config in
axy17lte Kconfig.
1. The global SYS_CONFIG_NAME in axy17lte Kconfig overrides
SYS_CONFIG_NAME for all boards specified after this line in
arch/arm/mach-exynos/Kconfig:
source "board/samsung/axy17lte/Kconfig"
Right now it's the last 'source' line there, so the issue is not
reproducible. But once some board is moved or added after this line
the next build error will happen:
GEN include/autoconf.mk.dep
In file included from ./include/common.h:16:
include/config.h:3:10: fatal error: configs/exynos78x0-common.h.h:
No such file or directory
3 | #include <configs/exynos78x0-common.h.h>
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
compilation terminated.
That's happening because axy17lte Kconfig defines SYS_CONFIG_NAME
option in global namespace (not guarded with any "if TARGET_..."), so
it basically rewrites the correct SYS_CONFIG_NAME defined in the
hypothetical boards which might appear after axy17lte in mach-exynos
Kconfig.
2. Another side of the issue is that SYS_CONFIG_NAME is defined
incorrectly in axy17lte Kconfig:
config SYS_CONFIG_NAME
default "exynos78x0-common.h"
The .h extension should not have been specified there. It's leading
to a build error, as the generated include file has a double '.h'
extension.
3. Each target in axy17lte/Kconfig defines its own SYS_CONFIG_NAME. But
all of those in fact incorrect, as corresponding
include/configs/<CONFIG_SYS_CONFIG_NAME>.h header files don't exist.
4. The global SYS_CONFIG_NAME pretty much repeats the help description
from arch/Kconfig and doc/README.kconfig.
Corresponding defconfig files (a*y17lte_defconfig) fix above issues by
overriding SYS_CONFIG_NAME and correctly setting it to
"exynos78x0-common".
Fix all mentioned issues by removing the incorrect global
SYS_CONFIG_NAME and instead specifying it (correctly) in SYS_CONFIG_NAME
options for each target instead.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Fixes: 3e2095e960 ("board: samsung: add support for Galaxy A series of 2017 (a5y17lte)")
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
If CONFIG_SYS_SKIP_UART_INIT is enabled, calculate the
current baud rate and update the "console" environment
variable.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Draco is a family of 3 boards: thuban, rastaban & etamin. Rename all
targets of the family adding the draco- prefix to increase readibility
and simplify future commits about concerning all boards of the family.
The name draco was initially used for the first target. It's deprecated
since a 2nd target was introduced. Unfortunately the draco target was
copied to the thuban target instead to be renamed. Remove it to save
unnecessary maintenance effort.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
