The board_eth_init() is only used by legacy ethernet driver framework,
so do not compile it when DM_ETH config has been selected.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The board_eth_init() is only used by legacy ethernet driver framework,
so do not compile it when DM_ETH config has been selected.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Move vsc7835 firmware uploading to board_early_init_r(), so that
the switch also can work in DM eTSEC driver.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Required for the generic distro mechanism.
Linux ships with 4 variants:
marvell/armada-3720-espressobin-v7-emmc.dtb
marvell/armada-3720-espressobin-v7.dtb
marvell/armada-3720-espressobin-emmc.dtb
marvell/armada-3720-espressobin.dtb
Use available information to determine the appropriate filename.
Fixes booting GRUB EFI arm64 on Fedora.
Reported-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Only set the fdtfile environment variable when not already set.
Fixes: 867572f09e ("ARM: mvebu: clearfog: run-time selection of DT file")
Cc: Joel Johnson <mrjoel@lixil.net>
Reported-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andre Heider <a.heider@gmail.com>
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For SPL flow without specifying address for DT loading DTB is automatically
appended behind U-Boot code. Specifically _end symbol is used. Just behind
it there is place for bss section.
It means if early code is using static variable and there is a write to
this variable DTB file is corrupted if variable is located between DTB
start and end.
In this particular case offset of this variable from bss section start is
very small (0x40) that's why DT is currupted which breaks this boot flow.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enabling saving variables to MMC(FAT), NAND, SPI based on primary bootmode.
Maybe that logic can be tuned for more complicated use cases and better
tested for different bootmodes.
Tested on zcu104 to SD(FAT) and JTAG(NOWHERE).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to have name variable saved in BSS section when it
doesn't need to be really used. That's why remove static from variable
definition and use strdup() to duplicate string with exact size from malloc
area instead.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current algorithm used to get the silicon name is bit complicated and
hard to follow. Updated to use more straightforward mechanism based on
the Device ID code table (Table 1-2). The full IDCODE register is used
(except device revision bits [31:28]) to get the device name and IDCODE2
value is used for identifying the variant.
Additionally to make the algorithm bit more clear it also save some space
as the devices table is slightly bit smaller.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot on xilinx boards is checking one address where DTB can be placed as
the first location for DTB. Originally this code was developed for Versal
where QEMU was putting generated DTB for U-Boot to use.
The patch enables changing this address which is necessary for cases where
default address is pointing to location (DDR) which is not present. The
access to this location can cause exception.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We already have a function to retrieve the mac address from one EEPROM.
For boards with a second Ethernet interface, however, we would
require another EEPROM with a second unique MAC address.
Introduce at91_set_eth1addr which will look for a second EEPROM
and set the 'eth1addr' variable with the obtained MAC address.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This patch moves the the config SYS_MALLOC_LEN to Kconfig
as it is already done for zynq arch in commit 01aa5b8f05
("Kconfig: Move config SYS_MALLOC_LEN to Kconfig for zynq").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Toradex product is called apalis-imx8 consisting of SoM with
i.MX8QM and i.MX8QP SoCs.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The Toradex product is called colibri-imx8x consisting of SoM with
i.MX8QXP and i.MX8DX SoCs.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Wrap video specific functionality with ifdefs.
Fixes: 195011b24d("colibri-imx7: fix splash logo drawing")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Drop show_boot_logo legacy function, as splashscreen functionality can
be used instead.
Fixes: d324189772("toradex: common: show boot logo")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Set proper splashscreen env value instead of calling legacy function
to show embed boot logo.
Fixes: 195011b24d("colibri-imx7: fix splash logo drawing")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Set proper splashscreen env value instead of calling legacy function
to show embed boot logo.
Fixes: 391c712dde("colibri-imx6ull: show boot logo")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
enable DTS support for keymile mpc83xx based boards.
get rid of compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Therefore done:
- add DTS for all mpc83xx based boards from keymile
mainly they are not mainlined to linux.
- add u-boot specific dtsi
- add stdout-path
- add missing ucc4 par_io definitions, which were
in board code, but not in linux DTS
- remove not used ethernet nodes
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Series-to: u-boot
Series-version: 3
Series-changes: 3
- rebase patchset to current mainline commit
c0192950df
- update defconfig files
Series-changes: 2
- add patch which fixes Codingstyle errors in drivers/qe
- add patch which converts the mpc83xx based boards from
keymile to DM_ETH
Cover-letter:
powerpc, mpc83xx: add DM_ETH support
This patch series adds DM ethernet support for mpc83xx based
keymile boards.
Travis build:
END
Use board_early_init_f() instead of mach_cpu_init() for board, the
board_early_init_f() is used for board init and after dm_initf, while
the mach_cpu_init() is used for CPU/SOC and before dm_initf()(not able
to use syscon API).
Fixes: 9cec336708 ("rockchip: evb-rv1108: Use syscon API to get grf base")
Fixes: 4aa33690fc {"rockchip: elgin-rv1108: Use syscon API to get grf base")
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
- Hyperflash boot for J7200
- Update Main R5FSS lockstep mode
- R5F remoteproc support for J7200
- Minor env fixes
- Add SPI boot support for am335x-icev2
am335x internal SRAM is too small to support the addition of
SPI bootmode to the default defconfig. Add a separate spiboot_defconfig
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
On J7200 SoC OSPI and HypeFlash are muxed at HW level and only one of
them can be used at any time. J7200 EVM has both HyperFlash and OSPI
flash on board. There is a user switch (SW3.1) that can be toggled to
select OSPI flash vs HyperFlash.
Read the state of this switch via wkup_gpio0_6 line and fixup the DT
nodes to select OSPI vs HyperFlash
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Chimp is a core in Broadcom netxtream controller (bnxt).
Add support to check bnxt's chimp component status.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Extend Kconfig for the board with board-specific commands selection.
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As the error message is now displayed by generic phy functions,
the pr_err can be change to pr_idebug.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Extend fastboot_set_reboot_flag arguments with reboot reason so that
it could handle different reboot cases in future.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
start.S does nothing and can be safely removed. Makefile is still being used
by the build system, so simply replace the rule in it. We use stub C-file
like it's done for other boards.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
start.S does nothing and can be safely removed. Makefile is still being used
by the build system, so simply drop the rule from it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
start.S does nothing and can be safely removed. Makefile is still being used
by the build system, so simply drop the rule from it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
start.S does nothing and can be safely removed. Makefile is still being used
by the build system, so simply drop the rule from it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
start.S does nothing and can be safely removed. Makefile is still being used
by the build system, so simply drop the rule from it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
start.S does nothing and can be safely removed. Makefile is still being used
by the build system, so simply drop the rule from it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
start.S does nothing and can be safely removed. Makefile is still being used
by the build system, so simply drop the rule from it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
start.S does nothing and can be safely removed. Makefile is still being used
by the build system, so simply drop the rule from it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
start.S does nothing and can be safely removed. Makefile is still being used
by the build system, so simply drop the rule from it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
start.S does nothing and can be safely removed. Makefile is still being used
by the build system, so simply drop the rule from it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
start.S does nothing and can be safely removed. Makefile is still being used
by the build system, so simply drop the rule from it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
start.S does nothing and can be safely removed. Makefile is still being used
by the build system, so simply drop the rule from it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
start.S does nothing and can be safely removed. Makefile is still being used
by the build system, so simply drop the rule from it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
start.S does nothing and can be safely removed. Makefile is still being used
by the build system, so simply drop the rule from it.
Cc: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Introduce USE_EARLY_BOARD_INIT option and select it by the actual users.
Cc: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Due to different partition layouts in different U-Boot versions, DTS for
Espressobin in Linux does not contain any definition of MTD partitions.
See commit https://git.kernel.org/stable/c/00954566464a4 for more details.
This patch via ft_board_setup() hook fills current partition layout used by
U-Boot, so booted kernel would see correct MTD partitions layout.
U-Boot env partition is calculated from CONFIG_ENV_OFFSET option.
First partition contains secure firmware, ARM trusted firmware and U-Boot
with checksums. So it is not possible to replace just one image (e.g.
U-Boot) without updating other parts where is stored checksum of U-Boot.
Therefore there is no extra partition defined for U-Boot and first
partition is called just 'firmware'.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Andre Heider <a.heider@gmail.com>
By default Topaz switch on Espressobin board forwards packets between all
ethernet ports, including CPU (port 0), wan (port 1) and lan (ports 2,3).
This default U-Boot setup is unsuitable for using Espressobin as router as
it opens security hole in forwarding all packets between wan and lan ports.
E.g. dhcp packets from wan network leaks to lan network during small time
window until U-Boot boots Linux kernel which loads network drivers which
disallows forwarding between wan and lan.
This patch fixes above problem. For Espressobin board prior putting Topaz
switch into forwarding mode, Topaz switch is reconfigured to allow
forwarding packets from wan and lan ports only to CPU port. This ensures
that packets from wan port are not forwarded to lan ports and vice-versa.
Packets from CPU port are still forwarded to all other ports, so U-Boot
network boot works with any ethernet port as before.
This problem was already discussed on Espressobin forum [1] and on
Marvell's github issue tracker [2]. As a workaround people on Espressobin
forum patched U-Boot to completely disable lan ports on Topaz switch which
prevented forwarding packets. That workaround had an issue that U-Boot was
unable to netboot via lan ports anymore. Change in this patch does not have
such issue.
This security issue has been dicussed here as well: [3].
[1] - https://web.archive.org/web/20191231164238/http://espressobin.net/forums/topic/boot-behavior-of-the-switch-and-security/
[2] - https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/issues/18
[3] - https://forum.armbian.com/topic/12635-espressobin-uboot-security-concerns-switch-init-portmask/
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
There shouldn't be a need to call additional i2c read if above failed
already. Based on comment it should be enough to try to detect legacy
boards which are mentioned in the comment.
Fixes: 2463f6728e ("ti: common: board_detect: Allow DM I2C without CONFIG_DM_I2C_COMPAT")
Fixes: 0bea813d00 ("ARM: omap-common: Add standard access for board description EEPROM")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Most likely these deprecated (removed) variables are not needed. Lets
remove the assignments completely from all spl.c files.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Oleksandr Zhadan and Michael Durrant
Reviewed-by: Simon Glass <sjg@chromium.org>
When this no-op dram_init_banksize() is removed, the weak default will
be used instead, which correctly sets the bi_dram[] banksize values.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Since commit 86cf1c8285 ("configs: Migrate CONFIG_NR_DRAM_BANKS") &
commit 999a772d9f ("Kconfig: Migrate CONFIG_NR_DRAM_BANKS"),
CONFIG_NR_DRAM_BANKS is always defined with a value (4 is default).
It makes no sense to still carry code that is guarded with
"#ifndef CONFIG_NR_DRAM_BANKS" (and similar). This patch removes
all these unreferenced code paths.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Add basic Marvell/Cavium OcteonTX/TX2 support (Suneel)
- Infrastructure changes to PCI uclass to support these SoC's (Suneel)
- Add PCI, MMC & watchdog driver drivers for OcteonTX/TX2 (Suneel)
- Increase CONFIG_SYS_MALLOC_F_LEN for qemu-x86 (Stefan)
- Sipeed Maix support S-mode.
- Provide command sbi.
- Use fdtdec_get_addr_size_auto_parent to get fu540 cache base address.
- Fix a compiler error with CONFIG_SPL_SMP=n.
- Fix sifive ram driver 32 compiler warnings.
- Fix kendryte/pll.h redefine nop() warning.
We have a number of platforms that are a combination of a carrier board
and System-on-Module (SoM) that in turn allows for the board to have
different SoCs on it. In some cases, this is handled via board-specific
Kconfig options. In other cases we make use of
CONFIG_SYS_EXTRA_OPTIONS. This latter case however can lead to invalid
configurations as we will not in turn get options that in Kconfig are
selected by or depend on that setting.
To resolve this, make the SoC option a choice in Kconfig and make boards
depend on what they can support. This change opens us up for further
clean-ups in the cases where a single CONFIG_TARGET_xxx can support
different SoCs and today they do not, or do not cleanly do so.
Reported-by: Matt Porter <mporter@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Soeren Moch <smoch@web.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Cc: Ian Ray <ian.ray@ge.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Cc: Simone CIANNI <simone.cianni@bticino.it>
Cc: Adam Ford <aford173@gmail.com>
Cc: Marcin Niestroj <m.niestroj@grinn-global.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Parthiban Nallathambi <parthiban@linumiz.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Niel Fourie <lusus@denx.de>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Richard Hu <richard.hu@technexion.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Silvio Fricke <open-source@softing.de>
Tested-by: Matt Porter <mporter@konsulko.com> [colibri_imx6]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This patch adds support for all OcteonTX2 96xx/95xx
boards from Marvell.
For 96xx boards, use octeontx_96xx_defconfig and
for 95xx boards, use octeontx_95xx_defconfig.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
This patch adds support for all OcteonTX 81xx/83xx
boards from Marvell.
For 81xx boards, use octeontx_81xx_defconfig and
for 83xx boards, use octeontx_83xx_defconfig.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Marek explained on IRC, that ft_board_setup() is not used / necessary
at all. So its best to just drop it completely, as it interferes with
the cleanup of CONFIG_MAX_PCI_REGIONS (completely removed).
Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide a defconfig that can be used to build U-Boot for the Maix boards
running upon OpenSBI.
Update the documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Total Compute is based on ARM architecture and has
the following features enabled in u-boot:
- PL011 UART
- PL180 MMC
- NOR Flash
- FIT image with Signature
- AVB
Signed-off-by: Usama Arif <usama.arif@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Linux kernel for arm32 requires dtb and initrd to be placed in low memory
to work properly. This requirement is described in chapter 4b) and 5) in
Linux documentation (Documentation/arm/booting.rst).
There is an issue on arm32 with 2GB of memory that bootm_size is bigger
than Linux lowmem (for example with VMSPLIT_3G). That's why limit bootm
size on these systems not to be above 768MB.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
env_set..() can failed that's why check return status and report it back to
make sure that user is aware that's something went wrong.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When bootm_low/bootm_size are setup properly there is no need to setup any
initrd_high address. Location for initrd is determined through LMB.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to build private function when
CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET is not defined. There is already weak
function which handles default case properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Start to use ENV_VARS_UBOOT_RUNTIME_CONFIG to enable/disable updating
variables with run time information.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove chip_id function and integrate the firmware call in the
zynqmp_get_silicon_idcode_name function. The change avoids querying the
firmware twice and makes the code bit more clear.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify the board init function to allow getting the chip ID when U-Boot
proper is executed at EL3.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current implementation for getting chip ID uses either raw access on EL3
or a SMC call to get the silicon information. Following change
simplifies the code using always the firmware driver.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Removes duplicated definition of PAYLOAD_ARG_CNT and define it in the
firmware driver. Additionally fixes payload buffer declarations without
macro usage
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Find and use the lowest memory for Versal to make sure that we keep u-boot
as low as possible and never use memory above u-boot's maximum VA mapping.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Versal loadpdi command is used for loading secure & non-secure
pdi images.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Origin function was calling strsep which replaced delimiter ',' by a null
byte ('\0'). Operation was done directly on FDT which ends up with the
following behavior:
ZynqMP> printenv fdtfile
fdtfile=xilinx/zynqmp.dtb
ZynqMP> fdt addr $fdtcontroladdr
ZynqMP> fdt print / compatible
compatible = "xlnx", "zynqmp"
As is visible fdtfile was correctly composed but a null byte caused that
xlnx was separated from zynqmp.
This hasn't been spotted because in all Xilinx DTs there are at least 3
compatible string and only the first one was affected by this issue.
But for systems which only had one compatible string "xlnx,zynqmp" it was
causing an issue when U-Boot's DT was used by Linux kernel.
The patch removes strsep calling and strchr is called instead which just
locate the first char after deliminator ',' (variable called "name").
And using this pointer in fdtfile composing.
Fixes: 91d7e0c47f ("arm64: zynqmp: Create fdtfile from compatible string")
Reported-by: Igor Lantsman <igor.lantsman@opsys-tech.com>
Signed-off-by: Igor Lantsman <igor.lantsman@opsys-tech.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On system with PL DDR which is placed before PS DDR in DT
env_get_bootm_size() and env_get_bootm_low() without specifying bootm_low
and bootm_size variables are taking by default gd->bd->bi_dram[0].start and
gd->bd->bi_dram[0].size. As you see 0 means bank 0 which doesn't need to be
PS ddr and even can be memory above 39bit VA which is what U-Boot supports
now.
That's why setup bootm variables based on ram_base/ram_size setting to make
sure that boot images are placed to the same location as U-Boot is placed.
This location should be by default location where OS can boot from.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Remove pinmux definition from pico-imx6ul.c
- Enable NET_RANDOM_ETHADDR for temporary solution, because micrel_ksz8xxx
driver does not support DM_ETH yet, so cannot read MAC address directly.
Before enable DM_ETH:
Net: FEC [PRIME]
After enable DM_ETH:
Net:
Warning: using random MAC address - ca:3f:43:8f:67:d4
eth1: ethernet@20b4000
Here is the test commands:
=> dhcp
BOOTP broadcast 1
DHCP client bound to address 10.88.88.94 (139 ms)
*** ERROR: `serverip' not set
Cannot autoload with TFTPGET
=> ping 8.8.8.8
Using ethernet@20b4000 device
host 8.8.8.8 is alive
Signed-off-by: Wig Cheng <wig.cheng@technexion.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Free resources used by Xen board before jumping to Linux kernel.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make required updates to run on u-boot.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Make required updates to run on u-boot and strip test code.
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Add support for Xen para-virtualized serial driver. This
driver fully supports serial console for the virtual machine.
Please note that as the driver is initialized late, so no banner
nor memory size is visible.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce a minimal Xen guest board running as a virtual
machine under Xen Project's hypervisor [1], [2].
Part of the code is ported from Xen mini-os and also uses
work initially done by different authors from NXP: please see
relevant files for their copyrights.
[1] https://xenbits.xen.org
[2] https://wiki.xenproject.org/
Signed-off-by: Andrii Anisov <andrii_anisov@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
It's better to keep all SPL related functions in the same spl.c.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Leo Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
This option was enabled during the earlier U-Boot porting time. Now
we already have the OTP driver in place and the unique MAC address
is read from the OTP, there is no need to turn on this option.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Leo Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
All FU540 driver related options should be in the SoC level Kconfig.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
spl_soc_init() seems to be a better name, as all SPL functions
names start from the spl_ prefix.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Use the generic board_init_f() provided by the RISC-V library codes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
- Add STM32 FMC2 EBI controller driver
- Fix dwc3-sti-glue which allows STiH410-B2260 to boot again
- Add fitImage its entry for 587-200 DHCOR SoM
- Add both PDK2 and DRC02 DT into DHCOM fitImage its
- Fix DHCOM KS8851 ethernet MAC address
- Remove stm32mp1 board.c file
- Use const for struct node_info in board stm32mp1.c file
-----BEGIN PGP SIGNATURE-----
iQJLBAABCgA1FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAl81JrkXHHBhdHJpY2Uu
Y2hvdGFyZEBzdC5jb20ACgkQysd4L3sz/6ZZBw//TiEtosS/6NRuC3kzK9KrpVUY
hIvrZldrh5lr+RZn7GqmNHD9CUZeXFBweG6ah5oHImsyaUdUnWZSftXykEzdIyoL
+r2j27npjqviATH1dZNliZnb/QiMsPmmf7XmF2MO0U7NTkbc7GMvsPWHAllk7jue
cPfa+uiRWsfM2oiHki6zC+QvfYQ5x+yxsWjoaOXgyAqjC8oIFBTqXFCHEYPhhZPr
9yu7uIXkahpEZe0x2J/5B0rCfgwpaX/fkF9OU35ThhpSEJOLWneiNwMtODGS96CQ
VjJhpdP3T/8TL8cQF+DJVP3tBQn60zepb12LvYY4Lhm08EolBRS8E/reukthkhWP
9C8KBHNFZG/PTccuHhF2t75AsFOQm37xR5S6qf2vjTYddTojqKQ404/BB89+jkJP
2bYfi5VZc9kz5gD4faGObHqqhhaMeC64ihrtJouFR8APS8IMEzsb282LX6mpa+IM
Id9zKHEyLZ9vig/ybQ2G1lpucFYtDrEcl7HBLFGrPkzWXhhvh8Onm6BGda378lBM
JTTstUlDPrmc8OSUR8RSE15LXnoYP4QfJwUUy2/DOYt3GoHWCIHAY2V5Eo+ATl7q
2p2/5pi/mOblSk5LW3cnjAqlnFmH7IVp4rLNLPvunRSDC34lhjvOzTgEiBvwqA/Z
2YbPPXFM7nwU/OXbG7w=
=J4aq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200813' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Use IS_ENABLED to prevent ifdef in board_key_check for STM32MP
- Add STM32 FMC2 EBI controller driver
- Fix dwc3-sti-glue which allows STiH410-B2260 to boot again
- Add fitImage its entry for 587-200 DHCOR SoM
- Add both PDK2 and DRC02 DT into DHCOM fitImage its
- Fix DHCOM KS8851 ethernet MAC address
- Remove stm32mp1 board.c file
- Use const for struct node_info in board stm32mp1.c file
Use const for the variable nodes in ft_board_setup,
this patch follow fdt_fixup_mtdparts prototype and no more use stack.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove the file board/st/stm32mp1/board.c which is not more
compiled since commit 156732cc8939 ("board: stm32mp1: move the
function board_debug_uart_init in spl.c")
Fixes: 4fb46816c7 ("board: stm32mp1: move the function board_debug_uart_init in spl.c")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The STM32MP1 DHCOM has two ethernet interfaces, the on-SoM DWMAC and KS8851.
Set eth1addr for the KS8851 to a MAC address of the DWMAC incremented by 1.
The MAC of the DWMAC is set from on-SoM EEPROM already, but the MAC address
of KS8851 was left uninitialized, so fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The new 587-200 DHCOR SoM is compatible with the 587-100 prototype,
hence just replicate the entries, as there is no pattern matching.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Include both PDK2 and DRC02 DTs in the DHCOM fitImage .its and implement
support in SPL to select the correct configuration entry for U-Boot by
using the machine compatible string from SPL DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in ft_board_setup.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in board_late_init.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in dk2_i2c1_fix.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use CONFIG_IS_ENABLED to prevent ifdef in set_dfu_alt_inf.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in sysconf_init.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in board_check_usb_power.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in g_dnl_board_usb_cable_connected
and in g_dnl_bind_fixup
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in board_key_check
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
On J7200 SoC OSPI0 and HypeFlash are muxed at HW level and only one of
them can be used at any time. J7200 EVM has both HyperFlash and OSPI
flash on board. There is a user switch (SW3.1) that can be toggled to
select OSPI flash vs HyperFlash.
Read the state of this switch via wkup_gpio0_6 line and fixup the DT
nodes to select OSPI0 vs HyperFlash
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add board detection support for j7200 common processor board.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
j7200-evm has minor differences with j721e-evm based on the IPs
available in the SoC. Introduce separate build targets for j7200-evm
to incorporate the differences.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
The DT nodes on J721E SoCs currently use a node name "interconnect" for
the various interconnects. This name is not following the DT schema, and
should simply be "bus". Update the fdt fixup logic to use both the current
and the expected corrected path names so that this logic won't be broken
with newer kernels.
Signed-off-by: Suman Anna <s-anna@ti.com>
Guard all eeprom probe with TI_I2C_BOARD_DETECT to avoid reading eeprom
when eeprom is not available
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Current usage of eeprom apis produce a build failure when
CONFIG_TI_I2C_BOARD_DETECT is not defined. Add stub function for these
apis to avoid build failures.
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Because of space constraints, create a new USB defconfig for R5 to
faciliate booting from USB mass storage devices
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Because of space constraints, create a new USB defconfig for R5 to
faciliate booting in USB peripheral (DFU) bootmode
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The DT nodes on AM65x SoCs currently use a node name "interconnect" for
the various interconnects. This name is not following the DT schema, and
should simply be "bus". Update the fdt fixup logic to use both the
current and the expected corrected path names so that this logic won't
be broken with newer kernels.
The logic also corrects the crypto node name as the DT node
unit-addresses are all expected to be lower case.
Signed-off-by: Suman Anna <s-anna@ti.com>
This commit completes the migrations for DM_ETH and DM_USB. The board
is now consistent with omap3_beagle and other remaining OMAP3 boards.
Cc: Tom Rini <trini@konsulko.com>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Move all assignments to gd->bd->bi_mem{start,size} to generic code in
setup_bdinfo.
Xtensa architecture is special in this regard as it defines its own
handling of gd->bd->bi_mem{start,size} fields. In order to avoid defining
a weak SDRAM function, let arch_setup_bdinfo overwrite the generic flags.
For ARC architecture, remove ARCH_EARLY_INIT_R from Kconfig since it is
not needed anymore.
Also, use gd->ram_base to populate bi_memstart to avoid an ifdef.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Acked-by: Alexey Brodkin <abrokdin@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Luka Perkov to CRS3xx-98DX3236 MAINTAINERS.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS328-4C-20S-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS326-24G-2S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS305-1G-4S Bit board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
The Bit board variant is added, which has a bigger Macronix flash.
Add basic U-Boot, UART and Winbond SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXykjtQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76a1WQCcD+objdS+90mDdT0yTpW3jHS4YiwAn2V2rTTo
4hKj5yxRg3cvb/pBAmbQ
=TyRs
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200804' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2020.10
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
This header file should not be included in other header files. Remove it
from each one and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable CONFIG_SPL_DM_SPI_FLASH to be able to boot from SPI NOR,
modify the offset of U-boot proper in the SPI NOR, so the
difference in offset matches between SPL and U-boot matches that of
the SD Card, allowing u-boot-with-spl.imx to also be copied to SPI
NOR at an offset of 0x400. Update the README to reflect this
change.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
MYS-6ULX is single board computer (SBC) comes with eMMC or NAND based
on imx6ULL SoC from NXP and provision for expansion board. This
commit adds support only for SBC with NAND.
CPU: Freescale i.MX6ULL rev1.1 528 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 45C
Reset cause: WDOG
Model: MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND
Board: MYiR MYS-6ULX 6ULL Single Board Computer
DRAM: 256 MiB
NAND: 256 MiB
MMC: FSL_SDHC: 0
In: serial@2020000
Out: serial@2020000
Err: serial@2020000
Net: FEC0
Working:
- Eth0
- MMC/SD
- NAND
- UART 1
- USB host
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Activate ENV in EXT4 support in sandbox.
The sandbox behavior don't change; the default environment with
the nowhere backend (CONFIG_ENV_IS_NOWHERE)is still used:
the weak function env_get_location() return ENVL_NOWHERE for priority 0.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Refactor to allow any arch to create SPI-flash images
New button uclass
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8g33sRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaeEgf/QhmJjd6lEE3ABncRa3texyqq7j9eu+9P
2JMCahrIzps83LLOkzNSGs1+m1hRuTcdnYNV8FxdmkAjDTYwV5RHOfwtpAr2nkH2
HBbJRA2qMPleqT8wcymouhaCIRTTCGfUkFgZ+OowwSlHnQ4d2oGU/59Z+AkbpfX0
3svA1Mlr5rUTZ3qTvdsepuZckuYOTGYZ5jgjbgr+G8F4iW4Ov+OkBxqDz9zFCveF
md5CHKP1SV+bq67Q9uqUEwatLzYpy1p24j1Qe4G08U1+XCi6r+95VEc7TWxggboj
eV/5d/sZbGESAtJiJ4TmqpGVcOLzBLI0FOunky0JNFwdcyRS/6KcCg==
=Xjil
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-28jul20' of git://git.denx.de/u-boot-dm
Use binman instead of one of the Rockchip build scripts
Refactor to allow any arch to create SPI-flash images
New button uclass
- fix SPL boot issue due to early dbgmcu_init() call
- fix SPL boot issue due to dcache memory region configuration
- add support of CONFIG_ENV_IS_IN_MMC
- add specific SD/eMMC partition for U-Boot enviromnent
- enable env in SPL
- use "env info -q" to remove log during boot
- remove env location override for dh_stm32mp1
- update management of misc_read
- check result of find_mmc_device in stm32prog
- use regulator_set_enable_if_allowed for disabling vdd supply in usbphyc
- enable CMD_ADTIMG flag to handle Android images
- device tree alignment with Linux Kernel v5.8-rc1
- remove hnp-srp-disable for usbotg on dk1
- add reset support to uart nodes on stm32mp15x
- use correct weak function name spl_board_prepare_for_linux
- use cd-gpios for ST and DHSOM boards
- add seeed studio odyssey-stm32mp157c board support
- move ethernet PHY into SoM DT
- add DHSOM based DRC02 board support
Add development keys used in FIT.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default relocation happens to a higher address of DDR,
i.e, DDR start + DDR size.
U-Boot shall be used to collect the ramdump.
Restrict U-Boot to use only the 16MB memory, so that this
memory can be reserved. Limit relocation to happen within
16MB memory, start 0xFF00_0000 and end 0x1_0000_0000
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add both DRAM banks memory information and
the corresponding MMU page table mappings.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add API to save boot parameters passed from BL31
Use assembly implementation of save_boot_params instead of c function.
Because generally ATF does not set up SP_EL2 on exiting.
Thus, usage of a C function immediately after exiting with no stack
setup done by ATF explicitly, may cause SP_EL2 to be not sane,
which in turn causes a crash if this boot was not lucky to get
an SP_EL2 in valid range. Replace C implementation with assembly one
which does not use stack this early, and let u-boot to set up its stack
later.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Signed-off-by: Rajesh Ravi <rajesh.ravi@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Broadcom Northstar 3 SoC.
NS3 is a octo-core 64-bit ARMv8 Cortex-A72 processors
targeting a broad range of networking applications.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On the UniElec U7623 board there is no external SD slot and the preloader
doesn't fill in the magic field at 0x81dffff0 to indicate that it was
booted from eMMC.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- SPL not supported yet --> no spl-dir in arch/arm/cpu/armv7/s5p4418/.
Appropriate line in Makefile removed.
- cpu.c: '#include <cpu_func.h>' added.
- arch/arm/cpu/armv7/s5p4418/u-boot.lds removed, is not required
anylonger.
- "obj-$(CONFIG_ARCH_NEXELL) += s5p-common/" added to
arch/arm/cpu/armv7/Makefile since s5p-common/pwm.c is used instead
of drivers/pwm/pwm-nexell.c.
- s5p4418.dtsi: '#include "../../../include/generated/autoconf.h"'
removed, is not necessary, error at out-of-tree building.
'#ifdef CONFIG_CPU_NXP4330'-blocks (2x) removed. Some minor changes
regarding mmc. 'u-boot,dm-pre-reloc' added to dp0 because of added
DM_VIDEO support.
- board/s5p4418/ renamed to board/friendlyarm/
- All s5p4418-boards except nanopi2 removed because there is no
possibility to test the other boards.
- Kconfig: Changes to have a structure like mach-bcm283x (RaspberryPi),
e.g. "config ..." entries moved from/to other Kconfig.
- "CONFIG_" removed from several s5p4418/nanopi2 specific defines
because the appropriate values do not need to be configurable.
- nanopi2/board.c: All getenv(), getenv_ulong(), setenv() and saveenv()
renamed to env_get(), env_get_ulong(), env_set() and env_save(),
respectively. MACH_TYPE_S5P4418 is not defined anymore, therefore
appropriate code removed (not necessary for DT-kernels).
- nanopi2/onewire.c: All crc8() renamed to crc8_ow() because crc8() is
already defined in lib/crc8.c (with different parameters).
- dts: "nexell,s5pxx18-i2c" used instead of "i2c-gpio", i2c0 and
i2c1 added. gmac-, ehci- and dwc2otg-entries removed because the
appropriate functionality is not supported yet. New mmc-property
"mmcboost" added.
s5p4418-pinctrl.dtsi: gmac-entries removed, mmc- and i2c-entries
added.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
possible (and similar).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Some instructions in the ARM ISA have multiple output registers, such
as ldrd/ldp (load pair), where two registers are loaded from memory,
but also ldr with indexing, where the memory base register is incremented
as well when the value is loaded to the destination register.
MMIO emulation under KVM is based on using the architecturally defined
syndrome information that is provided when an exception is taken to the
hypervisor. This syndrome information describes whether the instruction
that triggered the exception is a load or a store, what the faulting
address was, and which register was the destination register.
This syndrome information can only describe one destination register, and
when the trapping instruction is one with multiple outputs, KVM throws an
error like
kvm [615929]: Data abort outside memslots with no valid syndrome info
on the host and kills the QEMU process with the following error:
U-Boot 2020.07-rc3-00208-g88bd5b179360-dirty (Jun 06 2020 - 11:59:22 +0200)
DRAM: 1 GiB
Flash: error: kvm run failed Function not implemented
R00=00000001 R01=00000040 R02=7ee0ce20 R03=00000000
R04=7ffd9eec R05=00000004 R06=7ffda3f8 R07=00000055
R08=7ffd9eec R09=7ef0ded0 R10=7ee0ce20 R11=00000000
R12=00000004 R13=7ee0cdf8 R14=00000000 R15=7ff72d08
PSR=200001d3 --C- A svc32
QEMU: Terminated
This means that, in order to run U-Boot in QEMU under KVM, we need to
avoid such instructions when accessing emulated devices. For the flash
in particular, which is a hybrid between a ROM (backed by a read-only
KVM memslot) when in array mode, and an emulated MMIO device (when in
write mode), we need to take care to only use instructions that KVM can
deal with when they trap.
So override the flash read accessors that are used when running on QEMU
under KVM. Note that the the 64-bit wide read and write accessors have
been omitted: they are never used when running under QEMU given that it
does not emulate CFI flash that supports it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Add an override for enable_caches to enable the I and D caches, along
with the cached 1:1 mapping of all of DRAM. This is needed for running
U-Boot under virtualization with QEMU/kvm.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
When binman is in use, most of the targets built by the Makefile are
inputs to binman. We then need a final rule to run binman to produce the
final outputs.
Rename the variable to indicate this, and add a new 'inputs' target.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update management of misc_read, which now return length of data
after the commit 8729b1ae2c ("misc: Update read() and write()
methods to return bytes xfered")
Fixes: 8b8b3d6b55 ("stm32mp1: board: add environment variable for board id and board rev")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Overriding the environment location is not necessary as the defconfig
for the relevant boards only enable SPI flash and nowhere sources which
are in the same order per default but having this explicit override
prevents using eMMC or SD card (or EXT4) as environment source.
Signed-off-by: Jakob Riepler <jakob.riepler@aviloo.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate env config in SPL with CONFIG_SPL_ENV_SUPPORT
and use CONFIG_IS_ENABLED macro to test the activated
CONFIG_$(SPL_)ENV_IS_IN_... in env_get_location.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of CONFIG_ENV_IS_IN_MMC in env_get_location, used for
all mmc device (SD card and eMMC).
The 2 configs CONFIG_ENV_IS_IN_MMC and CONFIG_ENV_IS_IN_EXT4 are
incompatible.
Add the weak function mmc_get_env_dev to select the mmc boot instance.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
1. Configure white on black for video console.
2. Enable printing bmp logo during late board init stage.
3. Use iomux configuration from device tree.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Show boot logo embed in U-Boot blob.
2. Drop iomux configration for LCD, and use the one provided in device
tree.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This introduces support for EEPROM as a storage for the main Toradex
config block and additional config blocks on extra EEPROM chips (on
carrier board or video adapters).
To enable EEPROM as a storage for the main config block:
TDX_HAVE_EEPROM=y.
For additional EEPROMs please enable this Kconfig symbol:
TDX_CFG_BLOCK_EXTRA=y.
Information about existing EEPROM chips is provided via Device Tree
using aliases.
You can also write configuration for the carrier board using
create_carrier subcommand for cfgblock. Example:
Verdin iMX8MM # cfgblock create_carrier
Supported carrier boards:
UNKNOWN CARRIER = [0]
Verdin Carrier Board = [1]
Choose your carrier board (provide ID): 1
Enter carrier board version (e.g. V1.1B): V1.0A
Enter carrier board serial number: 10622780
Also with barcode:
Verdin iMX8MM # cfgblock create carrier -y 0156100010622780
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
- Drop ifdef CONFIG_SYS_I2C to initialize
baudrate of i2c
- Drop warning of i2c_early_init_f as follows,
warning: implicit declaration of function 'i2c_early_init_f'; did you
mean 'arch_early_init_r'? [-Wimplicit-function-declaration]
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable secure system counter in board_early_init_f for udelay()
to fix a bug that always return 0 by timer_read_counter()
when boot from qspi(No TFA)
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- Drop ifdef CONFIG_SYS_I2C to initialize
baudrate of i2c
- Drop warning of i2c_early_init_f as follows,
warning: implicit declaration of function 'i2c_early_init_f'; did you
mean 'arch_early_init_r'? [-Wimplicit-function-declaration]
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable secure system counter in board_early_init_f for udelay()
to fix a bug that always return 0 by timer_read_counter()
when boot from qspi(No TFA)
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for SDHC adapter identification and configuration
during board init.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The eSDHC adapter card identification and multiplexing configuration
through FPGA had been implemented in both common mmc driver and
fsl_esdhc driver. However it is proper to move these code to board
files and do it during board initialization. The FPGA registers are
also board specific.
This patch is to move eSDHC adapter card identification and
multiplexing configuration from mmc driver to specific board files.
And the option CONFIG_FSL_ESDHC_ADAPTER_IDENT is no longer needed.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[Rebased, Removed T1040QDS change as board does not exist]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add xspi boot source to qixis command to let the soc boot from
flex-nor flash chip.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The correct setting for the RGMII ports on LS1012ARDB is to
enable delay on both Rx and Tx so the interface mode used should
be PHY_INTERFACE_MODE_RGMII_ID
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The commit 361377dbdb ("ARM: rmobile: Merge prior-stage firmware DT
fragment into U-Boot DT on Gen3") reverted changes introduced by commit
175f502734 ("ARM: renesas: Configure DRAM size from ATF DT fragment")
that's why there is no reason to use functions with _fdt() suffix because
parameter is gd->fdt_blob as is already for functions without _fdt()
suffix.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Beacon EmbeddedWorks kit is based on the R8A774A1 SoC also
known as the RZ/G2M.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi.
Signed-off-by: Adam Ford <aford173@gmail.com>
- Fix SiFive HiFive Unleashed board booting failure problem.
- Enable SiFive fu540 PWM driver.
- Support SiFive fu540: SPI boot.
- Update OpenSBI used for RISC-V CI testing.
- Revert "riscv: Allow use of reset drivers".
- Revert "Revert "riscv: sifive: fu540: Add gpio-restart support"".
- sysreset: syscon:
- Don't assume default value for offset and mask property.
- Support value property.
- qemu: Add syscon reboot and poweroff support.
- Fix SIFIVE debug serial dependency.
- Fix linking error when building u-boot-spl with no SMP support.
- AE350 use fdtdec_get_addr_size_auto_noparent to parse smc reg.
- Make memory node available to SPL in hifive-unleashed-a00-u-boot.dtsi
- SiFive fu540 avoid using hardcoded ram base and size.
Use fdtdec_get_addr_size_auto_noparent to read the "reg" property
instead of fdtdec_get_addr. This will increase the compatibility
of dtb parsing.
Signed-off-by: Rick Chen <rick@andestech.com>
Acked-by: Leo Liang <ycliang@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Leo Liang <ycliang@andestech.com>
This adds syscon reboot and poweroff support to QEMU RISC-V.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
This reverts commit 23da3c682a.
Now the build failure of sifive_fu540_defconfig board has been fixed,
revert this "revert patch".
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Mark the default U-Boot environment as SPI flash since
this is an on board flash device.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Add support to detect boot mode at runtime for
SiFive FU540 boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
This patch enables SiFive PWM driver for the SiFive
Unleashed board.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
- New rk3326 board: Hardkernel Odroid Go2;
- Update board config and dts for RockPI 4/N8/N10;
- Update led boot on support for roc-rk3399-pc;
- Enable SPI Flash suppor for rk3328 rock64 board;
- Update rockchip pcie phy to use generic framework;
ROC-RK3399-PC has specific set of configurations for
on-board led setup.
Due to easiness for user to know the state of the board
roc-rk339-pc board code will setup the low power led
on/off, and waiting for user to press power key and then
glow full power led.
All this needs to happen only during power-on-reset not
for soft reset or WDT.
Also, it is not a proper usage to ask the user to press
the Power key if the board connected remotely, so add
the environment variable 'pwr_key' to check as well.
So, user need to press Power key only
- during POR
- pwr_key=y
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
roc-rk3399-pc has some specific requirements to support LEDS,
environment. board detection and etc prior to U-Boot proper.
So as of now SPL would be a better stage for these custom board
requirements to support unlike TPL. Adding few of these custom
requirements like LEDS in TPL would require extra code pulling
and also the size of TPL can grow.
So, this patch moves the leds code from TPL into SPL Board init
led_setup code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(split tpl.c change as separate patch)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enabled
GPIO pin change compared to 4B, 4C.
So, add or enable difference nodes/properties in 4C dts
by including common dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Also known as Odroid Go Advance but named Go2 internally by the
vendor it seems.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The commit 361377dbdb ("ARM: rmobile: Merge prior-stage firmware DT
fragment into U-Boot DT on Gen3") reverted changes introduced by commit
175f502734 ("ARM: renesas: Configure DRAM size from ATF DT fragment")
that's why there is no reason to use functions with _fdt() suffix because
parameter is gd->fdt_blob as is already for functions without _fdt()
suffix.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds very basic minimal support for the Marvell Octeon 3
CN73xx based EBB7304 EVK. Please note that the basic Octeon port does
not support DDR3/4 initialization yet. To still use U-Boot on with this
port, the L2 cache (4MiB) is used as RAM. This way, U-Boot can boot
to the prompt on this board.
Supported devices:
- UART
- reset
- CFI parallel NOR flash
Signed-off-by: Stefan Roese <sr@denx.de>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXxCxWw8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76bPyACcDZ8gD9jf1P/Zh+7kqrGdIWwURF8AnAiEtNnu
FhE/WQQj4mAEWE4F2bFE
=7ceG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200716' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
i.MX for 2020.10
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
