When the requested flash speed is 0, the baudrate division for the
requested speed causing drop in the performance. So set the ospi flash
to operate at max frequency when requested speed is zero.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220512100535.16364-6-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
On versal platform, enable apb linear mode for apb read and write
execute operations amd disable it when using dma reads. This is done by
xilinx_pm_request() secure calls when CONFIG_ZYNQMP_FIRMWARE is enabled,
else we use direct raw reads and writes in case of mini U-Boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220512100535.16364-5-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When flash operated at non default mode like DDR, flash need to be reset
to operate in SDR mode to read flash ids by spi-nor framework. Reset the
flash to the default state before using the flash. This reset is handled
by a gpio driver, in case of mini U-Boot as gpio driver is disabled, we
do raw read and write access by the registers.
Versal platform utilizes spi calibration for read delay programming, so
incase by default read delay property is set in DT. We make sure not to
use read delay from DT by overwriting read_delay with -1.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220512100535.16364-4-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for cadence ospi driver for Versal platform. This driver
provides support for DMA read operation which utilizes cadence qspi
driver.
If "cdns,is-dma" DT property is specified use dma for read operation
from cadence_qspi driver. As cadence_qspi_apb_dma_read() is defined in
cadence_ospi_versal driver add a weak function defination in
cadence_qspi driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220512100535.16364-3-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Move all the cadence macros from cadence_qspi_apb.c to cadence_qspi.h
file.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220512100535.16364-2-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The GXP supports 3 separate SPI interfaces to accommodate the system
flash, core flash, and other functions. The SPI engine supports variable
clock frequency, selectable 3-byte or 4-byte addressing and a
configurable x1, x2, and x4 command/address/data modes. The memory
buffer for reading and writing ranges between 256 bytes and 8KB. This
driver supports access to the core flash.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Replace reference to the correct name STMicroelectronics
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The nxp_fspi_default_setup() is only ever called from nxp_fspi_probe(),
where the IP clock are initially disabled. Drop the second disabling of
clock to prevent clock enable/disable imbalance reported by clock core:
"
clk qspi_root_clk already disabled
"
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There is a TX-FIFO and Shift Register empty(TFES) status
bit in spi controller. This commit checks the TFES bit
to wait the TX transfer completes.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
DMSTART bit must not be set while there is active transfer.
This commit sets the DMSTART bit only when the transfer begins.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
synquacer_cs_set() function does not wait the chip select
is deasserted when the driver sets the DMSTOP to deselect
the slave.
This commit checks the Slave Select Released(SRS) bit to wait
until the slave is deselected.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
"busy" variable is ORed without being initialized,
must be zeroed before use.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Satoru Okamoto <okamoto.satoru@socionext.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Move legacy spi_get_bus_and_cs() code to _spi_get_bus_and_cs().
Add new spi_get_bus_and_cs() implementation which rely on DT
for speed and mode and don't need any drv_name nor dev_name
parameters. This will prepare the ground for next patch.
Update all callers to use _spi_get_bus_and_cs() to keep the
same behavior.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Anji J <anji.jagarlmudi@nxp.com>
Cc: Biwen Li <biwen.li@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Waiting for SR_BUSY bit when receiving a new command is not needed.
SR_BUSY bit is already managed in the previous command treatment.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Currently, SR_TCF flag is checked in case there is data, this criteria
is not correct.
SR_TCF flags is set when programmed number of bytes have been transferred
to the memory device ("bytes" comprised command and data send to the
SPI device).
So even if there is no data, we must check SR_TCF flag.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add a mask parameter to control the lookup of the PCI region from which
the mapping can be made.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Evolve dm_pci_map_bar() to include an offset and length parameter. These
allow a portion of the memory to be mapped and range checks to be
applied.
Passing both the offset and length as zero results in the previous
behaviour and this is used to migrate the previous callers.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add Nuvoton NPCM BMC Flash Interface Unit(FIU) SPI master
controller driver using SPI-MEM interface.
The FIU supports single, dual or quad communication interface.
The FIU controller driver provides flash access in UMA(User
Mode Access) mode by using an indirect address/data mechanism.
the dts node is followed upstream kernel dts name.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[Jagan: fixed the Kconfig, Makefile order]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Use the spi_mem_default_supports_op() core helper in order to take into
account the buswidth specified by the user in device tree.
Fixes: 24c8ff4684 ("spi: Add Atmel QuadSPI driver")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add missing include for dm/device_compat.h. Without this include the
SFC driver fails to compile because dev_err and dev_dbg are not
defined.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The i.MX8M Mini and i.MX8M Plus flexspi IPs are compatible with one
another, however the linux kernel DT uses separate compatible string
for each SoC. Add the missing i.MX8MP compatible into this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This is a little tricky since SoCFPGA has code to determine this as
runtime. Introduce a guard variable for platforms to select if they
have a static value to use. Then for ARCH_SOCFPGA, call
cm_get_qspi_controller_clk_hz() and otherwise continue the previous
behavior.
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The designware spi driver unconditionally uses polling.
The comment to spi_hw_init() also states that the function should disable
interrupts.
According to the DesignWare DW_apb_ssi Databook, value 0xff in IMR enables
all interrupts. Since we want to mask all interrupts write 0x0 instead.
On the canaan k210 board, pressing the reset button twice to reset the
board will run u-boot. If u-boot boots Linux without having SPI interrupts
masked, Linux will hang as soon as interrupts are enabled, because of an
interrupt storm.
Properly masking the SPI interrupts in u-boot allows us to successfully
boot Linux, even after resetting the board.
Fixes: 5bef6fd79f ("spi: Add designware master SPI DM driver used on SoCFPGA")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
[Niklas: rewrite commit message]
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
The Canaan Kendryte K210 SoC DW apb_ssi v4 spi controller is documented
to have a 32 word deep TX and RX FIFO, which spi_hw_init() detects.
However, when the RX FIFO is filled up to 32 entries (RXFLR = 32), an
RX FIFO overrun error occurs. Avoid this problem by force setting
fifo_len to 31.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
"kendryte" is the marketing name for the K210 RISC-V SoC produced by
Canaan Inc. Rather than "kendryte,k210", use the usual "canaan,k210"
vendor,SoC compatibility string format in the device tree files and
use the SoC name for file names.
With these changes, the device tree files are more in sync with the
Linux kernel DTS and drivers, making uboot device tree usable by the
kernel.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The driver is currently using sizeof(op->cmd.opcode) in the op_len
calculation. Commit d15de62301 ("spi: spi-mem: allow specifying a
command's extension") changed op->cmd.opcode from one byte to two.
Instead, a new struct member op->cmd.nbytes is supposed to be used.
For regular commands op->cmd.nbytes will be one.
Commit d15de62301 ("spi: spi-mem: allow specifying a command's
extension") did update some drivers that overload the generic mem_ops()
implementation, but forgot to update dw_spi_mem_ops().
Calculating op_len incorrectly causes dw_spi_mem_ops() to misbehave, since
op_len is used to determine how many bytes that should be read/written.
On the canaan k210 board, this causes the probe of the SPI flash to fail.
Fix the op_len calculation in dw_spi_mem_ops(). Doing so results in
working SPI flash on the canaan k210 board.
Fixes: d15de62301 ("spi: spi-mem: allow specifying a command's extension")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
In the TI am65 device tree files there is no reset defined. Also
the Linux kernel driver uses devm_reset_control_get_optional_exclusive(..)
to get the reset.
Lets do the same as the kernel does and make thr reset optinal.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add a driver for the SPI controller integrated on Apple SoCs.
This is necessary to support the keyboard on Apple Silicon laopts
since their keyboard uses an Apple-specific HID over SPI protocol.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Spi memory operation interface is added to zynq qspi
driver to provide an high-level interface to execute
qspi controller specific memory operations by avoiding
spi_mem_exec_op() from spi-mem framework.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220131052240.23403-5-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a check afer baudrate calculation to see if the resultant value
falls within the range, else set it to default baudrate value.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220131052240.23403-4-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Read only one byte at a time from txbuf as txbuf may not be
aligned and accessing more than a byte at a time may cause
alignment issues. This fixes the issue of data abort exception
while writing to flash device.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220131052240.23403-3-ashok.reddy.soma@xilinx.com
This patch typecasts and accesses rx buf properly as
an unaligned rxbuf, typecasting with u16 and accessing
it causes data abort exception and this patch fixes it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220131052240.23403-2-ashok.reddy.soma@xilinx.com
The driver for SPI0 on Allwinner H6 SoCs did not use the correct define
SUN50I_GPC_SPI0 for the pin function, but one for a different Allwinner
SoC series.
Fix the conditionals to use the correct define for H6 SoCs. This matches
the conditional logic in the SPL spi driver.
Tested by probing the spi-flash on a pine64_h64-model-b board with
adapted device-tree (disable mmc2, enable spi0).
Signed-off-by: Daniel Wagenknecht <dwagenk@mailbox.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
On AM4372 the SPI_GCLK input gets its clock from the PRCM module which
divides the PER_CLKOUTM2 frequency (192MHz) by a fixed factor of 4.
See AM437x Reference Manual in section 27 QSPI >> 27.2 Integration.
The QSPI_FCLK therefore needs to take this factor into account and
becomes (192000000 / 4).
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----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=dLEg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmG8PNIcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyN4NCACbdi5EFjoNkGhCWLIX
SobXNcBGaL9Zpr5qZq77uFqFeFPeiAClk9X+TcSHhBTSWPugzNCdXEdENEGdiiOR
Yxe/QvBL7ZsKkhGBw5W8sb81NBPlpnVY7DWufjYvWq7S3C3bIDahQpCeWHKXDO0H
ZzIX1413kfHRKsAIT+IbufmC1dcWY8SWQEArSkL2KhTQyHnLVGAaholgEGXoKMoC
0ACXO+uhqaAY0/1eWvvYjcfotlz881ROajSRITh+Gu0UuHyRr2Fvj7jZvF5E4Q4f
Cu8iciDsimYSDGLZsOJjPIDTfsx9jbA8IcYIAMxOLW8OYbIL6QAUKsJ2LLKao1q5
SYXP
=YXsB
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.04 cycle:
This feature set includes : support for the new QSPI hardware on
sama7g5, small fixes on sam9x60 and sama7g5, some additions of commands
and PIO controller on sam9x60/sam9x60ek.
sama7g5 QSPI has:
1/ One Octal Serial Peripheral Interfaces (QSPI0) Supporting Up to
200 MHz DDR. Octal, TwinQuad, Hyperflash and OctaFlash Protocols Supported
2/ One Quad Serial Peripheral Interfaces (QSPI1) Supporting Up to
90 MHz DDR/133 MHz SDR
The QSPI controller of SAMA7G5 uses different clock domains, hence extra
synchronization operations must be performed before accessing some
registers. Differentiate between the versions of the IP using has_gclk.
Differentiate between QSPI0 and QSPI1 with has_octal.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Wait for the read/write transfer finish bit get actually cleared,
this does not happen immediately on at least SoCFPGA Gen5.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
It was wrongly set to "MR", fix it.
Fixes: 52e2565bfb ("spi: atmel-quadspi: Add verbose debug facilities to monitor register accesses")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
