BLANCHE is development board based on R-Car V2H SoC (R8A7792)
This commit supports the following periherals:
- SCIF, Ethernet, QSPI, MMC
Signed-off-by: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This can be used in the same way as other R-CAR serial setting.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This does not have much impact on behavior, but makes code look more
more like Linux. The use of devm_ioremap() often helps to delete
.remove callbacks entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Read information about clock frequency from DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Commit 83fd908f28 ("dm: imx: serial: Support DTE mode when using driver
model") breaks the serial output for the imx boards that do not use
the serial driver model.
The reason for the breakage is that it's setting UFCR_DCEDTE
unconditionally for the non-dm case.
So keep the original behavior by removing UFCR_DCEDTE setting in the
non-dm case.
Tested on mx7sabresd and mx6wandboard.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The MXC UART IP can be run in DTE or DCE mode. This depends on the
board wiring and the pinmux used and hence is board specific. This
extends platform data with a new field to choose wheather DTE
mode shall be used.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a driver that works with of-platdata. It sets up the platform data and
calls the standard ns16550 driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
With of-platdata this driver cannot know the format of the of-platdata
struct, so we cannot use generic code for accessing the of-platdata. Each
SoC that uses this driver will need to set up ns16550's platdata for it.
So don't compile in the generic code.
Signed-off-by: Simon Glass <sjg@chromium.org>
When this feature is enabled, we cannot access the device tree to find out
which serial device to use. Just use the first serial driver we find.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds 200MHz clock configuration for stm32f746 discovery board.
This patch is based on STM32F4 and emcraft's[1].
[1]: https://github.com/EmcraftSystems/u-boot
Signed-off-by: Toshifumi NISHINAGA <tnishinaga.dev@gmail.com>
Add support for standard type SCI (without FIFO) port.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The following changes are made to the clock API:
* The concept of "clocks" and "peripheral clocks" are unified; each clock
provider now implements a single set of clocks. This provides a simpler
conceptual interface to clients, and better aligns with device tree
clock bindings.
* Clocks are now identified with a single "struct clk", rather than
requiring clients to store the clock provider device and clock identity
values separately. For simple clock consumers, this isolates clients
from internal details of the clock API.
* clk.h is split so it only contains the client/consumer API, whereas
clk-uclass.h contains the provider API. This aligns with the recently
added reset and mailbox APIs.
* clk_ops .of_xlate(), .request(), and .free() are added so providers
can customize these operations if needed. This also aligns with the
recently added reset and mailbox APIs.
* clk_disable() is added.
* All users of the current clock APIs are updated.
* Sandbox clock tests are updated to exercise clock lookup via DT, and
clock enable/disable.
* rkclk_get_clk() is removed and replaced with standard APIs.
Buildman shows no clock-related errors for any board for which buildman
can download a toolchain.
test/py passes for sandbox (which invokes the dm clk test amongst
others).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Linflex module is integrated on some NXP automotive SoCs part of the former
Freescale portfolio, like S32V234, an SoC for Advanced Driver Assistance
Systems.
Original-signed-off-by: Stoica Cosmin-Stefan <cosminstefan.stoica@freescale.com>
Original-signed-off-by: Chircu Bogdan <Bogdan.Chircu@freescale.com>
Original-signed-off-by: Depons Eric <eric.depons@freescale.com>
Original-signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>
Add device tree support.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The CONFIG_OMAP1510 is no longer defined, so remove this dead code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Nishanth Menon <nm@ti.com>
The ns16550 driver needs serial_in_shift() and serial_out_shift()
when compiled in debug UART mode, so shift the DM_SERIAL check a
little to make these functions available.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds platform code for the Amlogic Meson GXBaby (S905) SoC and a
board definition for ODROID-C2. This initial submission only supports
UART and Ethernet (through the existing Designware driver). DTS files
are the ones submitted to Linux arm-soc for 4.7 [1].
[1] https://patchwork.ozlabs.org/patch/603583/
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If the UART is to be accessed using I/O port accessors (inb & outb) then
using map_physmem doesn't make sense, since it operates in a different
memory space. Remove the call to map_physmem when
CONFIG_SYS_NS16550_PORT_MAPPED is defined, allowing I/O port addresses
to not be mangled by the incorrect mapping.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
On Exynos platforms that support clock driver API, allow the driver to
use clock api get the SCLK clock rate.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The port id, if not specified in the device node, can be obtained from
the alias of the device node listed in the aliases node.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch add support for ar933x serial.
Signed-off-by: Wills Wang <wills.wang@live.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Boards can now use DM serial driver, or still legacy mcf uart
driver version.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Acked-by: Simon Glass <sjg@chromium.org>
dm_serial_ops.pending should return the number of characters, not just a
valid C Boolean integer value. The existing code does already does this,
but only as an accident since BCM283X_MU_LSR_RX_READY happens to be
BIT(0). Enhance the code to be more explicit about the values it returns.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
ISS is obsolete now and nSIM is used for simulation instead.
In its turn nSIM properly handles baud-rate settings so get rid
of now useless check.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This driver works in "new" Data Mover UART mode, so
will be compatible with modern Qualcomm chips only.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The RPi3 typically uses the regular UART for high-speed communication with
the Bluetooth device, leaving us the mini UART to use for the serial
console. Add support for this UART so we can use it.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
For ARM32 architecture, CONFIG_DEBUG_LL is available for early
low-level debugging (and actually UniPhier 32bit SoCs use it), but
ARM64 architecture does not support it. Instead, CONFIG_DEBUG_UART
is available as an architecture-independent debug facility.
This commit supports it on all the UniPhier SoCs (including the new
ARMv8 SoCs), which is very useful for new SoC bringups.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For Raspberry Pi, we had the input clock rate to the pl011 fixed in
the rpi.c file, but it may be changed by firmware due to user changes
to config.txt. Since the firmware always sets up the uart (default
115200 output unless the user changes it), we can just skip our own
uart init to simplify the boot process and more reliably get serial
output.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
reg-offset is the part of standard 8250 binding in the kernel.
It is shifting start of address space by reg-offset.
On Xilinx platform this offset is typically 0x1000.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Moved the new field to the end of the struct to avoid problems:
Signed-off-by: Simon Glass <sjg@chromium.org>
At present on x86 machines with use cache-as-RAM, the memory goes away just
before board_init_r() is called. This means that serial drivers are
no-longer unavailable, until initr_dm() it called, etc.
Any attempt to use printf() within this period will cause a hang.
To fix this, mark the serial devices as 'unavailable' when it is no-longer
available. Bring it back when serial_initialize() is called. This means that
the debug UART will be used instead for this period.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
As the handling for carriage return and line feed is done in the common
DM driver serial-uclass.c, such handling in some serial DM drivers is
duplicated and need to be removed.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In general, a carriage return needs to execute before a line feed.
The patch is to change some serial drivers based on this rule, such
as serial_mxc.c, serial_pxa.c, serial_s3c24x0.c and usbtty.c.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In general, a carriage return needs to execute before a line feed. The
patch is to change serial DM driver serial-uclass.c based on this rule.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This reverts commit d9a3bec682.
While this is a correct change to do long term it unfortunately breaks a
number of platforms that are using pdata and not named struct members so
they are getting all of their data after 'base' incorrect.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Enabling this driver requires some DT changes.
Adding DCC to root or main bus:
dcc: dcc {
compatible = "arm,dcc";
u-boot,dm-pre-reloc;
};
Extend alias list to link DCC:
serial0 = &uart0;
serial1 = &uart1;
serial2 = &dcc;
Change stdout-path to point to dcc port.
stdout-path = "serial2:115200n8";
Also add support for debug uart to help with early debug.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support for stm32f7 family usart peripheral.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
reg-offset is the part of standard 8250 binding in the kernel.
It is shifting start of address space by reg-offset.
On Xilinx platform this offset is typically 0x1000.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync logic with Linux kernel where TX empty flag is checked before char
is sent.
This logic is fixing problem with console on zynqmp platform.
For example:
DRAM: 2 GiB
Enabling Caches...
EL Level: �� sdhci@ff170000: 0
Using default environment
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
This does not appear to be used, and has not been converted to driver model
by the deadline (doc/driver-model/serial-howto.txt).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This does not appear to be used, and has not been converted to driver model
by the deadline (doc/driver-model/serial-howto.txt).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This does not appear to be used, and has not been converted to driver model
by the deadline (doc/driver-model/serial-howto.txt).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This does not appear to be used, and has not been converted to driver model
by the deadline (doc/driver-model/serial-howto.txt).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This does not appear to be used, and has not been converted to driver model
by the deadline (doc/driver-model/serial-howto.txt).
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch removes the uart clock enable from serial driver & move it in the
board code.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
All boards using this driver are with device tree support,
hence drop the legacy code in driver to have a pure DT solution.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This adds PIC32 UART controller support based on driver model.
Signed-off-by: Paul Thacker <paul.thacker@microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
xilinx_uartlite has been ported to DM, this patch makes the
xilinx-ppc405-generic and the xilinx-ppc440-generic boards use the new
DM driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Use dev_get_addr() instead of reading reg base directly in the driver.
Core function is also more robust.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP is using updated core with cdns,uart-r1p12 compatible string.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Move config option out of board file.
- Remove uartlite address from config file
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Zap the rockchip serial compatible string, because rockchip
serial has "snps,dw-apb-uart" compatible string in the dts.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Simon Glass <sjg@chromium.org>
clang-3.8 reports that serial_putc_raw_dev in serial_ns16550.c is
unused. Further investigation shows that we have 3 places that
implement this function and no callers, remove.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that driver model support is available, convert sandbox over to use it.
We can remove a few of the special hooks that sandbox currently has.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
This adds driver model support to lpuart serial driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Tested-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Create internal routines which take lpuart's register base as
a parameter, in preparation for driver model conversion.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
There is no need to go through serial driver subsystem, instead
call the driver's setbrg and putc routines directly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Clean up the driver codes a little bit, by:
- Use tab instead of space in the macro defines
- Use single line comment whenever possible
- Fix insertion of blank lines
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
LPUART is seen on Freescale VF610 and QorIQ Layerscape devices.
Create a Kconfig option and move it to defconfig for all boards
that have this serial driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch adds Kconfig entries to facilitate usage of pl01x as
a debug UART.
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch adds an ability to use pl01x as a debug UART. It must
be configured like other types of debug UARTs
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
[trini: Update for _debug_uart_init change]
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
The change ports NXP LPC32xx 14-clock UART device driver to driver
model.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allow the ns16550 debug UART to be used without the full driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
In very very space-constrained devices even the full UART driver is too
large. In this case the debug UART can still be used in some cases.
Add options to enable the UART driver in SPL and U-Boot proper. Enable both
options by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Use the driver model version of the function to find the BAR. This updates
the fdtdec function, of which ns16550 is the only user.
The fdtdec_get_pci_bdf() function is dropped for several reasons:
- with driver model we should use 'struct udevice *' rather than passing the
device tree offset explicitly
- there are no other users in the tree
- the function parses for information which is already available in the PCI
device structure (specifically struct pci_child_platdata which is available
at dev_get_parent_platdata(dev)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Mark _debug_uart_init() as static to avoid sparse warning and
inline it to debug_uart_init().
Reported-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch writes the default values for TXTL and RXTL to UARTx_UFCR.
Without this patch some older kernel versions crash as UARTx_UFCR was
not always correctly initialized.
Signed-off-by: Maximilian Schwerin <maximilian.schwerin@tigris.de>
Fix incorrect comment alignments.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
debug_uart.h is included twice.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove this c&p error from s5p driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For platforms that don't use device tree in SPL the only way to mark this
driver as 'required by relocation' is with the DM_FLAG_PRE_RELOC flag. Add
this to ensure that the driver is bound.
Fixes: fde7e18938 ("dm: tegra: pci: Move CONFIG_PCI_TEGRA to Kconfig")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Change reg-shift property default to zero. When the integer property
is missing, it should be taken as zero. This is consistent to Linux
drivers/tty/serial/of_serial.c.
The x86 and most powerpc use reg-shift of 0. Most others use reg-shift
of 2. While reg-shift of 1 is rarely used.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Zap CONFIG_NS16550_SERIAL, as the unification of ns16550 drivers
is completed.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Unify serial_omap, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Unify serial_tegra, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Unify serial_dw, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Unify serial_keystone, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Unify serial_rockchip, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Acked-by: Simon Glass <sjg@chromium.org>
Unify serial_ppc, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add TODO comment]
Signed-off-by: Tom Rini <trini@konsulko.com>
Unify serial_x86, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add generic binding to unify ns16550 drivers. There are
several drivers using almost the same code, such as serial_dw,
serial_keystone, serial_omap, serial_ppc, serial_rockchip,
serial_tegra.c, and serial_x86. But each is platform specific.
The key difference between these drivers is the way to get
input clock frequency. With this unified approach, fixed clock
frequency should be extracted from "clock-frequency" property of
device tree blob. If this property is not available, the macro
CONFIG_SYS_NS16550_CLK will be used. It can be a constant or a
function to get clock, eg, get_serial_clock().
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Change map_sysmem() to map_physmem(,,MAP_NOCACHE). Though map_sysmem()
can be used to map system memory, it might be wrong to use it for I/O
ports. The map_physmem() serves the same purpose to translate physical
address to virtual address with the additional flag to take care of cache
property. Most drivers use map_physmem() since I/O ports access should be
uncached. As ns16550 is a driver, it should use map_physmem() rather
than map_sysmem().
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Simon Glass <sjg@chromium.org>
Since commit 220e8021af ("nios2: convert altera_jtag_uart to
driver model"), the default debug uart was changed. Most people
use ns16550 UART, so restore it as default.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reported-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reported-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Change ioremap() to map_physmem(), as it is more used in u-boot.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Change ioremap() to map_physmem(), as it is more used in u-boot.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Follow commit 97b0597302 ("debug_uart: Adjust the declaration of
debug_uart_init()")
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Chin Liang See <clsee@altera.com>
Follow commit 97b0597302 ("debug_uart: Adjust the declaration of
debug_uart_init()")
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Chin Liang See <clsee@altera.com>
- Moved macro definitions to top
- Re-arrange header includes ascending order
- Remove unused header linux/compiler.h
- Remove the penultimate comma in of_match ids
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Replace numerical bit shift with BIT macro
in altera_uart
:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Jagan Teki <jteki@openedev.com>
- Moved macro definitions to top
- Give spaces around the '>>' in ALTERA_JTAG_WSPACE()
- Re-arrange header includes ascending order
- Remove unused header linux/compiler.h
- Remove the penultimate comma in of_match ids
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Replace numerical bit shift with BIT macro
in altera_jtag_uart
:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Update this driver to use driver model and change all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Since we use device tree in SPL also, we can drop this code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the debug UART to assist with early debugging. Enable it
for Zybo as an example.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sometimes stdout-path contains a UART alias along with speed, etc. For
example:
stdout-path = "serial0:115200n8";
Add support for decoding this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Both altera_jtag_serial_initialize() and
altera_serial_initialize() are no longer used after
they are converted to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Convert altera_uart to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Convert altera_jtag_uart to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adding compatibles for am335x, am437x and dra7 platforms.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
In some platforms like am437x, serial node is not populated with
clock-frequency node. So in that case have a default clock-clock
frequency.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
It is useful to see a message from the debug UART early during boot so that
you know things are working. Add an option to enable this. The message will
be displayed as soon as debug_uart_init() is called.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some boards need to set things up before the debug UART can be used. On
these boards a call to debug_uart_init() is insufficient. When this option
is enabled, the function board_debug_uart_init() will be called when
debug_uart_init() is called. You can put any code here that is needed to
set up the UART ready for use, such as set pin multiplexing or enable
clocks.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We want to be able to add other common code to this function. So change the
driver's version to have an underscore before it, just like
_debug_uart_putc(). Define debug_uart_init() to call this version.
Update all drivers to this new method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It looks like this line was copy-pasted, but not modified.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
This arch does not seem to be supported / used at all in the current
U-Boot mainline source tree any more. So lets remove the core u8500 code
and code that was only referenced by this platform.
Please note that this patch also removes these config options:
- CONFIG_PL011_SERIAL_RLCR
- CONFIG_PL011_SERIAL_FLUSH_ON_INIT
As they only seem to be referenced by u8500 based boards. Without any
such board in the current code, these config option don't make sense
any more. Lets remove them as well.
If someone still wants to use this platform, then please send patches
to re-enable support by adding at least one board that references this
code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add support for the Rockchip serial device using the ns16550 driver.
This uses driver model and device tree for both SPL and U-Boot proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
SANDBOX_SERIAL depends on SANDBOX, and SANDBOX selects DM.
So, "SANDBOX_SERIAL depends on DM" is redundant.
Likewise, UNIPHIER_SERIAL depends on ARCH_UNIPHIER, and
ARCH_UNIPHIER selects DM_SERIAL.
So, "UNIPHIER_SERIAL depends on DM_SERIAL" is redundant.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is a convenient way for a driver to get the hardware address of a
device, when regmap or syscon are not being used. Change existing callers
to use it as an example to others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Add SCIFA console interface for R-Car Gen2 SoCs.
SCIFA has different registers offsets and sizes then SCI. Hence it needs to
put it's macro definitions separately.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This driver is enabled only for UniPhier SoCs and ARCH_UNIPHIER now
selects OF_CONTROL and SPL_OF_CONTROL.
This driver no longer needs to support platform data configuration.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cleaning up order of include files by sorting them alphabetically
keeping in mind to leave common.h on top.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
- Import various DT files for DRA7 / DR72x / dra72-evm from Linux Kernel
v4.1
- Add config file for this board, enable DM and DM_GPIO
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The menuconfig for drivers are getting more and more cluttered
and unreadable because too many entries are displayed in a single
flat menu. Use hierarchic menu for each category.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Update to apply again in a few places, drop USB hunk]
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently the serial code assumes that there is always at least one serial
port (and panics / crashes due to null pointer dereferences when there is
none).
This makes it impossible to use u-boot on boards where there is no (debug)
serial port, because e.g. all uart pins are muxed to another function.
This commit adds a CONFIG_REQUIRE_SERIAL_CONSOLE Kconfig option, which
defaults to y (preserving existing behavior), which can be set to n on
such boards to make them work.
This commit only implements this for CONFIG_DM_SERIAL=y configs, as allowing
running without a serial port for CONFIG_DM_SERIAL=n configs is non trivial,
and is not necessary at this moment.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
As a debugging aid, allow UART3 to be used as a debug UART in SPL. This
is a precursor to proper UART support, which requires a substantial
refactor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a debug UART implementation for this serial driver. It does not set up
pinmux automatically - this must be done before calling debug_uart_init().
Signed-off-by: Simon Glass <sjg@chromium.org>
The debug UART code needs to perform the same init as the normal UART
driver. In preparation for this, move the init code into two functions, one
for the basic init and one for setting the baud rate. This will make adding
debug UART support easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a serial driver which makes use of EFI's console in/out service.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested on Intel Crown Bay and QEMU
Tested-by: Bin Meng <bmeng.cn@gmail.com>
In a final attempt to find a console UART this function uses the first
first available serial device. However the check for a valid device is
inverted.
This code is only executed when there is in fact no serial UART, but at
present it can fail to reach the panic_str() call in this case, and start
trying to use a non-existent UART.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since Rockchip requires 32-bit serial access, add this to the driver.
Refactor a little to make this easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Added UART DCC support for armv8
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This feature should be deprecated for new boards, and significantly adds
to SPL code size. Drop it. Instead, we can use stdout-path in the /chosen
node.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option is used by some boards, so support it with driver model. This
is really ugly - we should rewrite this driver once all users are moved to
driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
