Missing nodes may also be signaled via -ENODATA. We need to check for
that to prevent failing in non-usb3 setups.
Furthermore, dev.phy must be NULL'ed in case usb3-phy was not found.
Fixes: 142d50fbce ("usb: dwc3: Add support for usb3-phy PHY configuration")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
When the device tree indicates support for role switching through
the "usb-role-switch" property, take the "role-switch-default-mode"
property into account when deciding which role to put the
controller into.
This makes USB devices work on Apple M1 systems where the device
tree may include a "dr_mode" property that is set to "otg", but
where we need to put the controller into "host" mode to see
devices connected to the type-C ports.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Since commit 16cc5ad0b4 ("power: regulator: add dummy helper")
regulator dummy helper are always available even if DM_REGULATOR
is not set.
DM_REGULATOR flag is no more needed to protect no DM core,
remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a mask parameter to control the lookup of the PCI region from which
the mapping can be made.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Evolve dm_pci_map_bar() to include an offset and length parameter. These
allow a portion of the memory to be mapped and range checks to be
applied.
Passing both the offset and length as zero results in the previous
behaviour and this is used to migrate the previous callers.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The buffer is 512 bytes but read requests can be 800 bytes. Limit the
request to the size of the buffer.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When copying the string in copy_to_unicode(), check for the null
terminator in each position, not just at the start, to avoid reading
beyond the end of the string.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a bootdev driver for USB host. It can use the distro boot mechanism to
locate a file, or any other available bootmeth.
Signed-off-by: Simon Glass <sjg@chromium.org>
When usb3-phy label is found, PHY driver is called and serdes line is
initialized. This is preparation for serdes/psgtr driver to configure GT
lines based on description in DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The i.MX8MP glue needs to be configured based on a couple of DT
properties, implement .glue_configure callback to parse those DT
properties and configure the glue accordingly.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Rename the select_dr_mode callback to glue_configure, the callback is
used for more than enforcing controller mode even on the TI chips, so
change the name to a more generic one. No functional change.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
dev_read_size() returns -EINVAL (-22) if the property "g-tx-fifo-size"
does not exist. If that's the case, we now keep the default value of 0.
Signed-off-by: Wolfgang Grandegger <wg@aries-embedded.de>
With the omap-ehci driver now using the phy subsystem to enable
and disable reset, the driver no longer needs to know which
GPIO's are used, and they can be removed from Kconfig.
Signed-off-by: Adam Ford <aford173@gmail.com>
There are a few boards that use hard-coded GPIO definitions in
their respective defconfig files. If the GPIO's are listed
in their device trees, the nop-phy can toggle the GPIO's,
so the EHCI driver does not need to know anything about the
GPIO's. Add functions for getting the phys and remove the GPIO
toggles since the phy will now do that.
Signed-off-by: Adam Ford <aford173@gmail.com>
The USB_EHCI_OMAP driver currently has a series of Kconfig options
which let users specify a GPIO for the reset pin. Some devices
may have only one reset, while others might have more.
Since there is a nop phy driver, let's selct enable the PHY
system, and imply the nop phy driver. The nop phy driver can now
toggle the reset pins when putting the phy in and out of reset.
If the gpio is listed under the phy, it will get toggled and
the hard-coded config options specifying the GPIO numbers can
eventually go away.
Signed-off-by: Adam Ford <aford173@gmail.com>
The OMAP3 hierarchy has the ehci node as a sub-node of the
usbhshost. The usbhshost node contains an ohci and an ehci
subnode. The configuration of the ehci belongs in the
EHCI node and not its parent. Move it to the proper probe.
usb start
starting USB...
Bus ehci@48064800: USB EHCI 1.00
Bus usb_otg_hs@480ab000: Port not available.
scanning bus ehci@48064800 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Signed-off-by: Adam Ford <aford173@gmail.com>
omap_ehci_hcd_stop appears to be dead code, and omap_ehci_hcd_init
is only called by the probe function, so it can be static to that
function. Remove both from the header along with some additional
checking for DM_USB.
Signed-off-by: Adam Ford <aford173@gmail.com>
- a37xx: pci: Cleanup and minor fix for root port check (Pali)
- pci: mvebu: Ensure that root port is always on root zero bus (Pali)
- kwbimage: Fix dumping DATA registers for v0 images (Pali)
- kwbimage: Support for parsing extended v0 format (Pali)
- a37xx: Fix code and update DTS files to upstream version (Pali)
- a37xx: Fix and extend building memory map (Pali)
- ddr: marvell: a38x: fix BYTE_HOMOGENEOUS_SPLIT_OUT decision (Marek)
- mvebu: Optionally reset board on DDR training failure (Marek)
Official DT bindings use compatible string marvell,armada-3700-ehci.
Update drivers and DTS files.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There are devices which cause a USB stall when trying to read strings.
Specifically Arduino Mega R3 stalls when trying to read the product
string.
The stall currently remains unhandled, and subsequent retries submit new
transfers on a stopped endpoint which ultimately cause a crash in
abort_td():
WARN halted endpoint, queueing URB anyway.
XHCI control transfer timed out, aborting...
Unexpected XHCI event TRB, skipping... (3affe040 00000000 13000000 02008401)
BUG at drivers/usb/host/xhci-ring.c:505/abort_td()!
BUG!
resetting ...
Linux seems to be able to recover from the stall by issuing a
TRB_RESET_EP command.
Introduce reset_ep() which issues a TRB_RESET_EP followed by setting the
transfer ring dequeue pointer via TRB_SET_DEQ. This allows to properly
recover from a USB stall error and continue communicating with the USB
device.
Signed-off-by: Stefan Agner <stefan@agner.ch>
The kernel devicetree has definitions for port and hub nodes as subnodes
to the USB devices. These subnodes don't contain all of the data required
to properly configure the dwc3. Check the parent nodes if the data is not
in the port/hub node.
Here's an example from the librem5 kernel dts file
&usb_dwc3_0 {
#address-cells = <1>;
#size-cells = <0>;
dr_mode = "otg";
snps,dis_u3_susphy_quirk;
status = "okay";
port@0 {
reg = <0>;
typec_hs: endpoint {
remote-endpoint = <&usb_con_hs>;
};
};
port@1 {
reg = <1>;
typec_ss: endpoint {
remote-endpoint = <&usb_con_ss>;
};
};
};
&usb_dwc3_1 {
dr_mode = "host";
status = "okay";
#address-cells = <1>;
#size-cells = <0>;
/* Microchip USB2642 */
hub@1 {
compatible = "usb424,2640";
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
mass-storage@1 {
compatible = "usb424,4041";
reg = <1>;
};
};
};
Signed-off-by: Angus Ainslie <angus@akkea.ca>
The ci_req->hw_buf can be NULL, test whether it is and if so,
avoid accessing it. Else, the system may crash.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Li Jun <jun.li@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
The imx8mm and imx8mn appear compatible with imx7d-usb
flags in the OTG driver. If the dr_mode is defined as
host or peripheral, the device appears to operate correctly,
however the auto host/peripheral detection results in an error.
The solution isn't just adding checks for imx8mm and imx8mn to
the check for imx7, because the USB clock needs to be running
to read from the USBNC_PHY_STATUS_OFFSET register or it will hang.
Marek requested that I not enable the clocks in ehci_usb_of_to_plat,
so I modified that function to return an unknown state if the
device tree does not explicitly state whether it is a host
or a peripheral.
When the driver probes, it looks to see if it's in the unknown
state, and only then will it read the register to auto-detect.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
In DFU v1.1 specification [1] the DFU_UPLOAD (Short Frame)
is handled only in dfuUPLOADIDLE state:
- Figure A.1 Interface state transition diagram
- the state description in chapter A.2
A.2.3 State 2 dfuIDLE
on Receipt of the DFU_UPLOAD request,and bitCanUpload = 1
the Next State is dfuUPLOADIDLE
A.2.10 State 9 dfuUPLOAD-IDLE
When the length of the data transferred by the device in response
to a DFU_UPLOAD request is less than wLength. (Short frame)
the Next State is dfuIDLE
In current code, when an UPLOAD is completely performed after the first
request (for example with wLength=200 and data read = 9), the DFU state
stay at dfuUPLOADIDLE until receiving a DFU_UPLOAD or a DFU_ABORT request
even it is unnecessary as the previous DFU_UPLOAD request already reached
the EOF.
This patch proposes to finish the DFU uploading (don't go to dfuUPLOADIDLE)
and completes the control-read operation (go to DFU_STATE_dfuIDLE) when
the first UPLOAD response has a short frame as an end of file (EOF)
indicator even if it is not explicitly allowed in the DFU specification
but this seems logical.
[1] https://www.usb.org/sites/default/files/DFU_1.1.pdf
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmHyEeYRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYYlgf8C7tQVklXz9ZHhxVrFaPHWwgmBzEZJSrc
7SWhDX9yBrAYBUk8Q4OMnJz6nXW8Rz5Td9GfBNWcJag1HjJqno4BxkqwGk2tshgj
GIY0D1cGfKJzB4E6/rK/ETwmX4KVUyEf7S2IdJ0oydkn9t7OwDkUX5WtGXo70E7q
ZJGYlX5NQCVBRAF9NYDuyVFljrPzAiyT58VCtXY3q63C7PmRYvag8r56ug+8lkk3
9EbOTcwETqq9SbT1vucyBxwbUmoKhb2BF32jEcIhozowIM3GNsSpkdzQCUnylqfa
LYI/p0oVTKLfFRBRvQjLgdB/OQP8MLkby8A++Db2OW49mBXhn/5JWA==
=PdpE
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jan22' of https://source.denx.de/u-boot/custodians/u-boot-dm
acpi refactoring to allow non-x86 use
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
Add support for CDC ACM using the new UDC and gadget API. This protocol
can be used for serial over USB data transfer and is widely supported
by various OS (GNU/Linux, MS-Windows, OSX...). The usual purpose of
such link is to access device debug console and can be useful for
products not exposing regular UART to the user.
A default stdio device named 'usbacm' is created, and can be used
to redirect console to USB link over CDC ACM:
> setenv stdin usbacm; setenv stdout usbacm
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
This commit converts i.MX28's EHCI USB host driver to driver model
(DM_USB). It is a straightforward conversion (to reuse as much code
as possible), based on ehci-mx5.c code.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Those functions will be re-used when the ehci MXS driver (for imx28)
will be converted to also support CONFIG_DM_USB.
No functional changes introduced - only cosmetic changes (u32 type)
and alignment to pass checkpatch.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This function is going to be reused with the CONFIG_DM_USB enabled in
the imx28 mxs USB ehci driver.
No functional changes introduced.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
For whatever reason, usb_setup_ehci_gadget removes and probes USB device
0. However, not all systems have a device 0. Use the first device
instead.
The device probed should probably have something to do with the
controller (as specified by e.g. ums <controller> or fastboot
<controller>). In fact, I find it odd that we probe the USB device in
the first place, because this is just to set up the gadget itself.
Presumably, the controller should be probed by usb_gadget_initialize
somehow.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
Add parameter spl_boot_device to spl_parse_board_header(), which allows
the implementations to see from which device we are booting and do
boot-device-specific checks of the image header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix fastboot flash bug.
If the downloading file size is equal to the partition size, "fastboot
flash" can't work, at least in sunxi platform, because used an
uninitalized point: ep->desc.
This patch also fixed 'data abort' bug in am335x platform.
Reproduce: fastboot flash loader1 spl/sunxi-spl.bin.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Fastboot support has been broken on platforms using dwc2 controller
since the gadget gets its max packet size from it.
This patch is the equivalent of 723fd5668f which fixed the same issue
but for the chipidea controller.
Fixes: 27c9141b11 ("usb: gadget: fastboot: use correct max packet size")
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This ensures the USB_MUSB_PIO_ONLY config is set to an apppropriate
value from the changes enabling USB_MUSB_GADGET does.
Namely, USB_MUSB_PIO_ONLY default to =y on USB_MUSB_SUNXI being y.
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Add support for the proper dwc3 device tree binding support as specified
in the offical device tree spec.
Initially, add support for the LS1028A support. Other SoCs should be
easy to add by just adding the corresponding compatible string.
Unfortunately, the device trees of all other layerscape SoCs are not
converted and uses a wrong compatible string only known in u-boot.
To maintain backwards compatibility with current u-boot device trees,
add the generic "fsl,layerscape-dwc3" compatible string.
OTG mode is not supported yet. The dr_mode in the devicetree will either
have to be set to peripheral or host.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
[backport from linux commit d9612c2f0449e24983a8b689603210486a930c90]
Enable the undefined length INCR burst type and set INCRx.
Different platform may has the different burst size type.
In order to get best performance, we need to tune the burst
size to one special value, instead of the default value.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
[backport from linux commit db2be4e9e30c6e43e48c5749d3fc74cee0a6bbb3]
Add adjust_frame_length_quirk for writing to fladj register
which adjusts (micro)frame length to value provided by
"snps,quirk-frame-length-adjustment" property thus avoiding
USB 2.0 devices to time-out over a longer run
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Both dr_mode and maximum-speed properties are usually optional. Drivers
will still try to fetch the properties nonetheless, which leads to error
messages, although they are no errors. Change pr_err() to pr_debug().
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official ls1028a binding of the driver uses the following as
compatibles:
compatible = "fsl,ls1028a-dwc3", "snps,dwc3";
Change the ls1028a device tree and add this new compatible to the fsl
specific xhci driver, otherwise the generic dwc3 driver will be used
with the compatibles above.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When allocate the GPD ring, and tell its address to the controller, then
the driver starts or resumes the QMU, the controller will try to access
the first GPD, so need flush the first one to avoid wrong GPD status.
Reported-by: Xin Lin <Xin.Lin@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
dev_err seems to be moved to different header file. Include
dm/device_compat.h file to compile properly.
Fixes: 69dae8902b ("linux/compat.h: Remove redefinition of dev_xxx macros")
Signed-off-by: Stefan Agner <stefan@agner.ch>
On mvebu this is defined if and only if !ARM64.
Otherwise it is defined for boards with ARCH_MX23, ARCH_TEGRA and
ARCH_ZYNQ, and also for SOC_AR934X (tplink_wdr4300).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
This option is only used for
mx23evk_defconfig
mx23_olinuxino_defconfig
which are the only i.MX23 boards.
Add depend on ARCH_MX23 and default to y.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
In preparation for moving this option to Kconfig, rename it to be
consistent with other USB EHCI Kconfig options.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----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=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
Add usb_gadget_handle_interrupts(), usb_gadget_register_driver()
and usb_gadget_unregister_driver() to be able to test
binding usb gadget.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add an entry in usb_gadget_controller_number() for the DWC2
gadget controller. It is used to bind the USB Ethernet driver.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reported-by: Herbert Poetzl <herbert@13thfloor.at>
Cc: Marek Vasut <marex@denx.de>
Cc: Herbert Poetzl <herbert@13thfloor.at>
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will
remove the asm/arch/gpio.h header. In preparation, clean up the various
files that include it.
Some files did not contain any GPIO code at all, so this header was
completely unused.
A few files contained only legacy platform-specific GPIO code for
setting up pin muxes. They were left unchanged, as that code will be
completely removed by the DM_PINCTRL migration.
The remaining files contain some combination of DM_GPIO and legacy GPIO
code. For those, switch to including asm/gpio.h (if it wasn't included
already). Right now, this header provides both sets of functions,
because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the
right header to include once the DM_GPIO migration is complete and
GPIO_EXTRA_HEADER is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Upstream Linux uses the "amlogic,meson-axg-usb-ctrl" for AXG SoCs.
This adds it to the compatible list for this driver.
Reported-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Vyacheslav Bocharov <adeep@lexina.in>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last mx35 platform, remove that support as
well.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This converts the following to Kconfig:
CONFIG_OMAP_EHCI_PHY1_RESET_GPIO
CONFIG_OMAP_EHCI_PHY2_RESET_GPIO
CONFIG_OMAP_EHCI_PHY3_RESET_GPIO
To do this, we also introduce CONFIG_HAS_CONFIG_OMAP_EHCI_PHYn_RESET_GPIO
options to get setting the GPIO number.
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point in time, all platforms that had previously used
drivers/usb/phy/omap_usb_phy.c have been migrated to DM and related
options. Remove this now unused code and some related unused defines.
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds support for the DWC_sub31 controllers such as those
found on Apple's M1 SoC. This version of the controller
seems to work fine with the existing driver.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Allow using different PHY interfaces for multiple USB controllers. When no
value is set in DT, we fall back to CONFIG_MXC_USB_PORTSC for now to stay
compatible with current board configurations.
This also adds support for the HSIC mode of the i.MX7.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Import usb_phy_interface enum values and DT match strings from the Linux
kernel.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Some platforms, like the Allwinner H6, do not have a separate glue layer
around the dwc3. Instead, they rely on the clocks/resets/phys referenced
from the dwc3 DT node itself. Add support for enabling the clocks/resets
referenced from the dwc3 DT node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Resetting an XHCI controller inside xhci_register undoes any register
setup performed by the platform driver. And at least on the Allwinner
H6, resetting the XHCI controller also resets the PHY, which prevents
the controller from working. That means the controller must be taken out
of reset before initializing the PHY, which must be done before calling
xhci_register.
The logic in the XHCI core was added to support the Raspberry Pi 4
(although this was not mentioned in the commit log!), which uses the
xhci-pci platform driver. Move the reset logic to the platform driver,
where it belongs, and where it cannot interfere with other platform
drivers.
This also fixes a failure to call reset_free if xhci_register failed.
Fixes: 0b80371b35 ("usb: xhci: Add reset controller support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
There are a number of DWC2 configuration options that are set in dwc2.h
and referenced in dwc2.c only. Move these out of the CONFIG_DWC2
namespace and in to the DWC2 namespace. Note that hikey was defining an
option that was already always enabled, so we can remove that hunk.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that DM_PCI is always enabled, check on CONFIG_PCI instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Update for non-PCI users of this code, reword]
Signed-off-by: Tom Rini <trini@konsulko.com>
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
As the deadline for migration to DM_USB, when using a USB host
controller has now gone two years past the deadline, enforce migration.
This is done by:
- Ensuring that all host controller options (other than the very legacy
old MUSB ones) now select USB_HOST. USB_HOST now enforces DM_USB and
OF_CONTROL.
- Remove other parts of Kconfig logic that had platforms pick DM_USB.
- To keep Kconfig happy, have some select statements test for USB_HOST
as well.
- Re-order some Kconfig entries and menus so that we can cleanly pick
host or gadget roles. For the various HCD options that have platform
glue options, group them together and update dependencies in some
cases.
- As SPL_DM_USB is not required, on platforms that had not yet enabled
it, disable it.
Cc: Marek Vasut <marex@denx.de>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Samuel Holland <samuel@sholland.org>
Cc: FUKAUMI Naoki <naobsd@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The ST-Ericsson DB8500 SoC contains a MUSB OTG controller which
supports both host and gadget mode. For some reason there is
nothing special about it - add a simple glue driver for Ux500
that literally just sets up MUSB together with a generic PHY.
There are no SoC-specific registers etc needed to make USB work.
The new Ux500 glue driver is only tested to work with DM_USB
and DM_USB_GADGET. Both host and gadget mode work fine on
the u8500 "stemmy" board that is already present in U-Boot.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Unlike imx6, on imx7 the USB PHY is described as:
usbphynop1: usbphynop1 {
compatible = "usb-nop-xceiv";
clocks = <&clks IMX7D_USB_PHY1_CLK>;
clock-names = "main_clk";
#phy-cells = <0>;
};
which does not have the 'reg' property.
Do not return an error when the 'reg' property is not found
for the USB PHY.
This fixes USB gadget regression on a imx7s-warp board.
Successfully tested the "ums 0 mmc 0" command on two boards:
imx7s-warp and imx6dl-pico-pi.
Signed-off-by: Fabio Estevam <festevam@denx.de>
On a imx7s-warp board the fdtdec_get_alias_seq() function
always fails.
As priv->portnr is only used on i.MX6, move fdtdec_get_alias_seq()
inside the CONFIG_MX6 block.
Signed-off-by: Fabio Estevam <festevam@denx.de>
When `usb start` is called on the terminal, the dwc2 driver will try
to start every USB device as host first, even if it is explicitly
configured as peripheral in the device tree (dr_mode = "peripheral").
So to avoid an unwanted 15 seconds delay when initializing the usb
(one second per channel = 1s x 15), this patch adds a check to the
initialization, and will skip host initialization of the device is
explicitly set as peripheral. The checking is already done similarly
in the `drivers/usb/gadget/dwc2_udc_otg.c` driver.
Signed-off-by: João Loureiro <joaofl@gmail.com>
Kernel device tree got updated to use clock name as "ref" instead of
"usb2_refclk". Fix cdns3-ti.c to use the correct name.
Fixes: 70e167495a ("arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot")
Fixes: 6239cc8c4e ("arm: dts: k3-j7200: Sync Linux v5.11-rc6 dts into U-Boot")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Even if only USB gadget is defined, dwc3 generic driver enables
a definition and probe/remove functions for host driver.
This enables the definition if USB_HOST is enabled only.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
All newer Allwinner SoCs (since about 2013) miss the CONFIGDATA register
in their MUSB implementation, so they need a quirk to hardcode this.
Currently this quirk depends on listing the SoCs affected in musb_reg.h,
which means that this list needs to grow with every new chip.
Move the quirk feature into Kconfig, next to PIO_ONLY, and change the
default to y (for Allwinner builds), while listing the early
implementations as exceptions.
This fixes USB peripheral operation on some newer SoCs, which were not
explicitly listed before.
Tested on H6, H616, R40 (which were broken before), and also on the H5
and A20, for regressions.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
If the PHY isn't specified in the DT, -ENODATA means it should be skipped,
handle it like -ENOENT.
With that, devices without USB3 supported can have USB working (Odroid-HC4).
Fixes: adb049abf7 ("usb: dwc3: Add Meson G12A USB Glue")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
For systems which use generic PHY support and implement USB PHY driver,
the parsing of PHY properties is unnecessary, disable it.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
According to EHCI spec, software needs to do handshake with HC for
safely removing QH from async list. This handshake is implemented by
setting IAAD (Interrupt on Async Advance Doorbell) bit in USB_USBCMD
register and poll the IAA (Interrupt on Async Advance bit) in the
USB_USBSTS to ensure the HC has released all on-chip state that may
potentially reference one of the data structures just removed.
Current codes only check active status of the last QTD, but this can't
ensure the QH is released from HC. We can meet unrecoverable
"EHCI timed out on TD" errors when running UEFI SCT tests on USB disk.
The USB_ASYNCLISTADDR register is changed to a invalid address when the
issue happens. It is fixed after adding the IAA handshake.
Steps to reproduce the issue:
1. Build the UEFI SCT from https://github.com/tianocore/edk2-test
2. Build the EDK2 UEFI Shell from https://github.com/tianocore/edk2
3. Copy SCT files and Shell.efi to USB disk FAT partition
4. Load the Shell.efi from USB FAT, and run bootefi to execute it
5. After booting into Shell, enter the SCT directory and run "sct -a"
to execute all tests.
6. Tests run about 1 hour and stop with many EHCI timeout errors like
EHCI timed out on TD - token=0x801f8c80
Signed-off-by: Ye Li <ye.li@nxp.com>
The iMX8M uses nop PHY, select PHY and NOP_PHY automatically.
Otherwise, the DM capable driver is now perfectly compatible.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Fix cast from pointer to integer of different size by casting the
pointer to uintptr_t instead of uint32_t, the former has correct
size on both 32bit and 64bit architectures.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Add new compatible string, used by some more up-to-date DTs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
There is now multiple copies of CONFIG_MXC_USB_PORTSC in configs set to
PORT_PTS_UTMI | PORT_PTS_PTW, which is in fact the default register value
for MX6, MX7 and MX7ULP. Define the default value of CONFIG_MXC_USB_PORTSC
in the driver and use it in case CONFIG_MXC_USB_PORTSC is not defined in
config, to reduce the duplication.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
In case PHY support is enabled, use the generic EHCI PHY support
to start and stop the PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
In case the platform uses DM, determine port number, which is
used as offset in USBMISC registers, from PHY node DT aliases,
just like Linux does.
Fixes: 4de51cc25b ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Instead of passing ad-hoc sequence number to usb_oc_config(), pass in
the USB MISC address itself. The USB MISC address comes from DT in DM
case, and from the old method using controller index in non-DM case.
Fixes: 4de51cc25b ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Split usb_power_config() per SoC and pass in USB PHY, USBNC and ANATOP
addresses instead of ad-hoc sequence numbers. This is only applicable
on legacy systems which do not implement proper PHY support. Once PHY
support is available, parts of this can be removed altogether and moved
to the PHY driver, similar to Linux phy-mxs-usb.c .
Fixes: 4de51cc25b ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Instead of passing ad-hoc index to USB PHY handling functions and then
try and figure out the PHY address, pass in the PHY address itself. For
DM case, this address comes easily from DT. For non-DM case, the previous
method is still present, however the non-DM case will soon be removed.
Fixes: 4de51cc25b ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
In order to pass component addresses around easily instead of passing
ad-hoc sequence numbers, it is necessary to split ehci_mx6_common_init().
Make it so and call the separate functions instead.
Since board_ehci_hcd_init() makes no sense in DM case, do not call it
in DM case.
Fixes: 4de51cc25b ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
In case DM and OF controler is enabled, but PHY support is disabled,
parse USB PHY and MISC component addresses from DT manually. Those
component addresses will be used in subsequent patches to access the
ANATOP, PHY and MISC registers matching the controller and thus get
rid of the ad-hoc controller sequence number mapping.
Fixes: 4de51cc25b ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Merge USBNC register layout structure into a single one, instead of
having three separate structures and a lot of ifdeffery. No functional
change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Add support for using DM clock framework to enable and disable all the
necessary clock for the USB controller.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
The driver turns on Vbus regulator in probe, but fails to turn it back
off in case of probe failure. Add the missing code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
This introduces strlcat, which provides a safer interface than strncat. It
never copies more than its size bytes, including the terminating nul. In
addition, it never reads past dest[size - 1], even if dest is not
nul-terminated.
This also removes the stub for dwc3 now that we have a proper
implementation.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change makes debugging a bit easier as the output is better
readable with the added space. The explicit le16_to_cpu() is not
needed in the output. Also this patch moves the strings into one line
to make the patch checkpatch clean.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Accessing the xHCI controller registers should be done via the
xhci_readl/writel functions. This patch adds this to a few missing
places.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
When flush cache of the current GPD and resume QMU, the controller
will try to access the next GPD after processing the current one,
if not flush the next GPD, the controller may get wrong GPD status.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
All debug messages from ep0.c except a few are printed by dbg_ep0() macro.
So for remaining few exceptions use also dbg_ep0() instead of serial_printf().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
If we do not set FIFO buffer address and size for some endpoint which is in
use then default programmed address 0x0 would be used which is in conflict
with address of FIFO buffer for endpoint 0. Moreover address of FIFO buffer
for endpoint 0 cannot be programmed, it is fixed to 0x0. Sharing address
space between more endpoints cause data loss and unexpected errors.
This patch is fixing transmission of characters over usbtty serial console
and allows using of usbtty for debugging purposes on Nokia N900.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Interrupt for EP0 is indicated in intrtx register via first bit. This bit
is set for both RX and TX despite register has only TX in its name. First
bit in intrrx register is reserved, not used and never set.
So remove calling musb_peri_ep0() function at every iteration of udc_irq()
and musb_peri_rx() and call it only from musb_peri_tx() when correct
interrupt bit in initrtx it set.
Address from SET ADDRESS command must be set to faddr register only after
acknowledging SERV_RXPKTRDY followed by received EP0 interrupt. So prior
calling musb_peri_ep0_set_address() check for EP0 interrupt instead of
(incorrect) MUSB_INTR_SOF interrupt.
This patch fixes issue that host (computer) cannot register U-Boot USB
device and is failing with errors:
usb 1-1: new full-speed USB device number 86 using xhci_hcd
usb 1-1: Device not responding to setup address.
usb 1-1: Device not responding to setup address.
usb 1-1: device not accepting address 86, error -71
U-Boot was writing address to faddr register too early and did not wait for
correct interrupt after which should update address.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
If musb_peri_rx_ep() was called to process received HW buffer but U-Boot
cannot read it yet (e.g. because U-Boot SW buffer is full) then interrupt
was marked as processed also when HW buffer stayed unprocessed.
U-Boot tried to process this buffer again when it received interrupt again,
but it can receive it only when sender (host) sends a new data. As sender
(host) is not going to send a new data until U-Boot process current data
this issue caused a deadlock in case sender (host) is emitting data faster
than U-Boot can process it.
Reading musb intrrx register automatically clears this register and marks
interrupt as processed. So to prevent marking interrupt in U-Boot as
processed, adds a new variable pending_intrrx which would contain
unprocessed bits of intrrx register.
For a second step, every time when musb_peri_rx_ep() is called and there
are waiting data to be processed (signaled by MUSB_RXCSR_RXPKTRDY) either
acknowledge sender (via musb_peri_rx_ack()) that whole HW buffer was
processed or set corresponding bit in pending_intrrx that HW buffer was not
fully processed yet and next iteration is required after U-Boot allocates
space for reading HW buffer.
This patch fixes receiving large usb buffers, e.g. file transfer via Kermit
protocol implemented by 'loadb' U-Boot command over usbtty serial console.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
If udc_endpoint_write() was called with bigger payload which does not fit
into one USB packet it is needed to transmit payload in more USB packets.
First packet is transmitted by udc_endpoint_write() call itself and other
packets are put into waiting queue.
Implement function musb_peri_tx() which checks if endpoints are ready for
transmit and continue transmission of waiting queue.
This patch fixes sending big output from printenv command over usbtty
serial console.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>>
PERI_RXCSR is 16bit register so store its value into 16bit local variable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
This patch fixes configuring FIFOs for one-directional endpoints which have
only one queue (either RX or TX, but noth both).
Size of FIFO buffer is 2^(idx+3) bytes and starting address is 2^(addr+3).
Moreover first 64 bytes are reserved for EP0.
Without this patch if FIFO size specified by caller was zero then idx was
incorrectly calculated (expr. ffs(0)-1) and size overflowed in fifosz
register. This register uses has only 4 bits for FIFO size. Moreover
specifying zero buffer size is not possible (with idx=0 is minimal buffer
size 8 bytes).
So even for one-directional endpoints we need to correctly specify both
(RX and TX) FIFO buffer sizes and its addresses.
This patch is fixing calculation of start address and buffer size to
minimal value and ensures that it would not overlap with buffer reserved
for EP0.
This issue caused loose of packets on USB bus in both directions and
basically usbtty was unusable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Without this patch clearing was done only when U-Boot was compiled with
MUSB Host Controller. But clearing of data toggle bit is needed also for
MUSB Device Controller otherwise Device Controller does not work correctly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Since commit 8745b9ebcc ("usb: gadget: add super speed support")
ums was no more functional on platform which use dwc2_udc_otg driver.
This was due to a too restrictive test which checked that the gadget
driver speed was either FS or HS.
So all gadget driver with max speed set to speed higher than
HS (SS in case of composite gadget driver in our case) are not
allowed, which is wrong.
Update the speed test in usb_gadget_register_driver() and in
dwc2_gadget_start() to allow all gadget driver speed equal or higher
than FS.
Tested on stm32mp157c-ev1 board.
Fixes: c791c8431c ("usb: dwc2: convert driver to DM_USB_GADGET")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
add support for the UUU commands ACmd and UCmd.
Enable them through the Kconfig option
CONFIG_FASTBOOT_UUU_SUPPORT
base was commit in NXP kernel
9b149c2a2882: ("MLK-18591-3 android: Add FSL android fastboot support")
and ported it to current mainline. Tested this patch
on imx6ul based board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
So far we've been content with passing physical addresses when
configuring memory addresses into XHCI controllers, but not all
platforms have buses with transparent mappings. Specifically the
Raspberry Pi 4 might introduce an offset to memory accesses incoming
from its PCIe port.
Introduce xhci_virt_to_bus() and xhci_bus_to_virt() to cater with these
limitations, and make sure we don't break non DM users.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
[mb: fix compilation for 32 bit]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
fix from nicolas
The PCIe bus the controller is connected to might need to be removed
prior the handover. Make sure xhci-pci is also removed so as to avoid
unexpected timeouts or hangs.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The Linux kernel v5.7-rc1 introduced the compatible "st,stm32mp15-hsotg".
See Linux kernel commit d49850110434 ("dt-bindings: usb: dwc2: add
support for STM32MP15 SoCs USB OTG HS and FS")
This patch updates the supported compatible in DWC2 driver,
removes the add-on done in U-Boot dtsi and keeps the compatible
defined in SOC dtsi arch/arm/dts/stm32mp151.dtsi:
usbotg_hs: usb-otg@49000000 {
compatible = "st,stm32mp15-hsotg", "snps,dwc2";
reg = <0x49000000 0x10000>;
...
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Testing with v2021.01 on MIPS Octeon has shown, that the latest patch
for the "short packet event trb handling" did introduce a bug on
platforms with virtual address != physical address. This patch fixes
this issue by using the correct address types in the compare (both
physical in this case).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Ran Wang <ran.wang_1@nxp.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Function dm_pci_map_bar() may fail and returns NULL. Check this to prevent
dereferencing a NULL pointer.
In xhci-pci this may happen when board does not enable CONFIG_PCI_PNP and
PCI_BASE_ADDRESS_0 contains unconfigured zero address.
Signed-off-by: Pali Rohár <pali@kernel.org>
Add support to disable specific ports, it's useful for some
scenarios:
1. usb3 PHY is shared whith PCIe or SATA, the corresponding
usb3 port can be disabled;
2. some usb2 or usb3 ports are not used on special platforms,
they should be disabled to save power.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
As we need standard usb_ep's desc, so set it when enable ep.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Change to use wMaxPacketSize of current speed EP desc for request
length wrap up.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Remove the gadget driver speed check, and set its max_speed to
be USB_SPEED_HIGH.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If one of functions is not super speed capable, we need force the udc
to be high speed, this is an equivalent implementation of
usb_gadget_udc_set_speed() in kernel but simple, which set the gadget
max_speed to be high speed, so afterwards when start gadget duc can
set the HW to be USB 2.0 mode.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set its max_speed to be super speed.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add super speed EP config.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is to add usb gadget super speed support in common
driver, including BOS descriptor and select the super speed
descriptor from function driver.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Always use the new added config for os_desc_config to fix cdev->
os_desc_config may miss set in case we restart usb gadget driver.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current way to set cdev->os_desc_config is wrong if user restart
fastboot, as the old config is not used anymore and new allocated
usb_configuration will be used, so set the os_desc_config while
usb_add_config.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add device interface GUID for Microsoft Extended Properties Feature
Descriptor.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This is a proting patch from linux kernel: 37a3a533429e
("usb: gadget: OS Feature Descriptors support"), the original commit
log see below:
There is a custom (non-USB IF) extension to the USB standard:
http://msdn.microsoft.com/library/windows/hardware/gg463182
They grant permission to use the specification - there is
"Microsoft OS Descriptor Specification License Agreement"
under the link mentioned above, and its Section 2 "Grant
of License", letter (b) reads:
"Patent license. Microsoft hereby grants to You a nonexclusive,
royalty-free, nontransferable, worldwide license under Microsoft鈥檚
patents embodied solely within the Specification and that are owned
or licensable by Microsoft to make, use, import, offer to sell,
sell and distribute directly or indirectly to Your Licensees Your
Implementation. You may sublicense this patent license to Your
Licensees under the same terms and conditions."
The said extension is maintained by Microsoft for Microsoft.
Yet it is fairly common for various devices to use it, and a
popular proprietary operating system expects devices to provide
"OS descriptors", so Linux-based USB gadgets whishing to be able
to talk to a variety of operating systems should be able to provide
the "OS descriptors".
This patch adds optional support for gadgets whishing to expose
the so called "OS Feature Descriptors", that is "Extended Compatibility ID"
and "Extended Properties".
Hosts which do request "OS descriptors" from gadgets do so during
the enumeration phase and before the configuration is set with
SET_CONFIGURATION. What is more, those hosts never ask for configurations
at indices other than 0. Therefore, gadgets whishing to provide
"OS descriptors" must designate one configuration to be used with
this kind of hosts - this is what os_desc_config is added for in
struct usb_composite_dev. There is an additional advantage to it:
if a gadget provides "OS descriptors" and designates one configuration
to be used with such non-USB-compliant hosts it can invoke
"usb_add_config" in any order because the designated configuration
will be reported to be at index 0 anyway.
This patch also adds handling vendor-specific requests addressed
at device or interface and related to handling "OS descriptors"."
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As other users may use utf8_to_utf16le() to convert the utf8
to utf16 for usb, so move it to head file.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This is a porting patch from linux kernel: 19824d5eeece
("usb: gadget: OS String support"), original commit log
see below:
"There is a custom (non-USB IF) extension to the USB standard:
http://msdn.microsoft.com/library/windows/hardware/gg463182
They grant permission to use the specification - there is
"Microsoft OS Descriptor Specification License Agreement"
under the link mentioned above, and its Section 2 "Grant
of License", letter (b) reads:
"Patent license. Microsoft hereby grants to You a nonexclusive,
royalty-free, nontransferable, worldwide license under Microsoft鈥檚
patents embodied solely within the Specification and that are owned
or licensable by Microsoft to make, use, import, offer to sell,
sell and distribute directly or indirectly to Your Licensees Your
Implementation. You may sublicense this patent license to Your
Licensees under the same terms and conditions."
The said extension is maintained by Microsoft for Microsoft.
Yet it is fairly common for various devices to use it, and a
popular proprietary operating system expects devices to provide
"OS descriptors", so Linux-based USB gadgets whishing to be able
to talk to a variety of operating systems should be able to provide
the "OS descriptors".
This patch adds optional support for gadgets whishing to expose
the so called "OS String" under index 0xEE of language 0.
The contents of the string is generated based on the qw_sign
array and b_vendor_code.
Interested gadgets need to set the cdev->use_os_string flag,
fill cdev->qw_sign with appropriate values and fill cdev->b_vendor_code
with a value of their choice.
This patch does not however implement responding to any vendor-specific
USB requests."
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As the SDP protocol use the predefined ep num for communication, we can't
change its name hence reset its ep num while do ep autoconfig, this is
only apply for SPL.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since some new fields in usb_ep structure been moved to usb_ss_ep.
The CDNS3 gadget driver should replies on this operation to bind the
usb_ss_ep with the endpoint descriptor when function layer uses
usb_ep_autoconfig to add endpoint descriptors to gadget. So that
CDNS3 driver can know the EP information and configure the EP once
the set configuration request is received.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Each array is used only in one file (core.c or ep0.c). Move their content
to correct file, mark them as static and do not export out of current file.
This change allows to decrease size of u-boot.bin as more of those strings
are not used.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reinitialize dfu_env_entities after flashing the 'SCRIPT' entity to
ensure that the potential changes to the 'dfu_alt_info' environment
variable are applied.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
In case of usb_add_function() failure the error path has an issue,
i.e the global pointer variable is assigned to garbage
Fix the above mentioned issue by assigning pointer to NULL.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In case of usb_add_function() failure the error path has two issues:
- the potentially allocated structure isn't getting freed
- the global pointer variable is assigned to garbage
Fix the above mentioned issues by freeing memory and assigning NULL.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Casting 32bit int value directly into 64bit unsigned type causes
wrong value for file size equal or larger than 2GB. Fix the wrong
file size by casting uint32_t first.
Fixes: commit 1fe9ae76b1 ("gadget: f_thor: update to support more than 4GB file as thor 5.0")
Reported-by: Junghoon Kim <jhoon20.kim@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have two functions which do the same thing. Standardise on
dev_has_ofnode() since there is no such thing as an 'invalid' ofnode in
normal operation: it is either null or missing.
Also move the functions into one place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Now that there is only one sequence number (rather than both requested and
assigned ones) we can simplify this function. Also update its caller to
simplify the logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the new sequence number in all cases. Since all devices are assigned
a number when bound, this hack should not be needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This hack cannot work in the new sequence-numbering scheme. Remove it
while we wait for the maintainer to complete DM conversion as noted in
the existing comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove the redundant setting for USB_RX_EARLY_SIZE. Besides, for
RTL8153B, it is necessary to notify the hardware of the changes
of the aggregation settings.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
The r8152_eth_probe() may allocate a memory for ss->dev_priv.
It has to be freed if r8152_eth_probe() fails finally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
For bulk IN transfer, the codes will set ISP flag to request event TRB
being generated by xHC for the case of short packet. So when encountering
buffer-cross-64K-boundary (which we will divide payload and enqueuqe
more than 1 transfer TRB), and the first TRB ends up with a short packet
condition it will trigger an short packet code transfer event per that
flag and cause more than 1 event TRB generated for this transfer.
However, current codes will only handle the first transfer event TRB
then mark current transfer completed, causing next transfer
failure due to event TRB mis-match.
Such issue has been observed on some Layerscape platforms (LS1028A,
LS1088A, etc) with USB ethernet device.
This patch adds a loop to make sure the event TRB for last transfer TRB
has been handled in time.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use generic Synopsys DesignWare 3 driver on Intel Edison.
For now it's just a stub which allows future refactoring.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
dwc3_meson_g12a_force_mode() sets the dr-mode of the USB PHY. However
it skips setting the mode if it matches the one done during driver probe
(stored in private structure). This fails if the mode has been changed
to other value and then back to initial one. Fix this by configuring the
dr-mode always, regadless of the one set at the driver probe).
This fixes operation of USB gadget based drivers when they are initialized
for the second time.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Fix up the code style for those declarations that should now fit onto one
line, which is all of them that currently do not.
This is needed for dtoc to detect the structs correctly, at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
If CONFIG_PHY is not enabled then the dwc3_setup_phy()
returns ENOTSUPP which can be still valid and intentional
so modify error check to handle this -ENOTSUPP.
The same error handling exists in drivers/usb/host/xhci-dwc3.c already
added by commit d648a50c0a ("dwc3: move phy operation to core.c").
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On some board, the ID pin is not connected so the B session must be
overridden with "u-boot,force_b_session_valid" but the VBus sensing
must continue to be handle.
To managed it, this patch adds a new DT field
"u-boot,force-vbus-detection" to use with "u-boot,force_b_session_valid"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add an entry in usb_gadget_controller_number() for the MTU3
gadget controller. It is used to bind the USB Ethernet driver.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds support for the MediaTek USB3 DRD controller,
its host side is based on xHCI, this driver supports device mode
and host mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
There is only declaration of usb_speed_string(), but no definition,
so add it to avoid build error when call it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In buffer DMA mode, gadget should re-configure EP 0 to received SETUP
packets when doeptsiz.xfersize is equal to a setup packet size(8 bytes)
and EP 0 is in WAIT_FOR_SETUP state.
Since EP 0 is not enabled in WAIT_FOR_SETUP state, SETUP packets is NOT
received from RxFifo and wriiten to the external memory.
Signed-off-by: Chance.Yang <chance.yang@vatics.com>
This driver doesn't use DM (in the correct places), so we use a device and
not a udevice. We also need to include device_compat.h
Signed-off-by: Sean Anderson <seanga2@gmail.com>
