Commit graph

22338 commits

Author SHA1 Message Date
Po Liu
380b8f307c powerpc/c29xpcie: Getting DDR SPD image from 16-bit sub-address EEPROM
Currently, there is only one EEPROM on c29xpcie board which is AT24C1024.
We program the SPD data at beginning of the AT24C1024.But the AT24C1024
has a 16-bit sub-address mode. This patch is tomake it work when getting
SPD in a 16-bit sub-address EEPROM.

Signed-off-by: Po Liu <Po.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-12-04 14:54:32 -08:00
Zhao Qiang
c3cc02af6c powerpc/p1010rdb:modify the mtest start_address
In new board P1010RDB-PB, the interrupt vector table is at
the start of memory. So if the start_address needs to be set
a proper value.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-12-04 14:54:24 -08:00
Dave Liu
24936ed1c9 powerpc/corenet: CPC1 speculation disable
In PBL RAMBOOT(SPI/SD/NAND boot) mode, CPC1 used as SRAM, should disable
CPC1 speculation and keep it till relocation. Otherwise, speculation
transactions will go to DDR controller, it will cause problem.

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-12-04 14:54:10 -08:00
Tom Rini
f44483b57c Merge branch 'serial' of git://git.denx.de/u-boot-microblaze 2013-12-02 08:48:02 -05:00
Tom Rini
19210ae983 Merge branch 'master' of git://git.denx.de/u-boot-mips 2013-12-02 08:44:28 -05:00
Masahiro Yamada
e40acc0a59 Blackfin: remove executable permission of AWK script
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-12-02 08:44:02 -05:00
Tom Rini
77fdd6d1eb Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2013-12-02 08:38:28 -05:00
Soren Brinkmann
2785a4ae76 serial: zynq: Remove unused #defines
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Series-to: trini, uboot
2013-12-02 11:36:36 +01:00
Paul Burton
67d4752d1d malta: set CONFIG_SYS_BOOTM_LEN to 64MB
Allow a larger kernel binary to be decompressed - the default 8MB can
become limiting on a Malta.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-26 21:49:42 +01:00
Paul Burton
bea12b7823 malta: enable PIIX4 SERIRQ
Whilst U-boot does not require this itself, Linux currently relies upon
it having been muxed and enabled by the bootloader. Thus in order to
preserve compatibility with current kernels before a fix is merged in
Linux we will enable the SERIRQ interrupt and mux it to its pin.

Without doing this current kernels will never receive serial port
interrupts and the end result is typically that userland appears to
hang.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-26 21:49:34 +01:00
Paul Burton
72117dadcb malta: correct UART baudrate
CONFIG_SYS_NS16550_CLK specifies the rate of the clock 16x the baud
rate. The SMSC FDC37M81x datasheet states that a divider of 1 results in
a UART at 115200 baud, thus the x16 clock rate is 115200 * 16.
Previously the divider was left at 0 which led to a rate of 38400 baud
regardless of CONFIG_BAUDRATE or the baudrate environment variable.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-26 21:49:25 +01:00
Paul Burton
d18d49d7ad mips: don't hardcode Malta env baudrate
The baudrate passed to Linux in the environment was hardcoded at 38400.
Instead pass the correct baudrate from global data, allowing Linux to
correctly inherit the baudrate used by U-boot when console setup is not
explicitly specified.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-26 21:49:17 +01:00
Tom Rini
d19ad726bc Prepare v2014.01-rc1
Signed-off-by: Tom Rini <trini@ti.com>
2013-11-25 16:49:32 -05:00
Shengzhou Liu
f7f155e1e1 t2080qds/ramboot: enable PBL tool for t2080qds
Add the default RCW(SerDes 0x66_0x16) and PBI configure file for
T2080QDS board, so we can use PBL tool to generate the ramboot
image to support boot from NAND/SPI/SD.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2013-11-25 12:36:55 -08:00
Shengzhou Liu
c4d0e81156 powerpc/t2080qds: add support for t2080qds board
The T2080QDS is a high-performance computing evaluation, development and
test platform supporting the T2080 QorIQ Power Architecture processor.

T2080QDS feature overview
Processor:
 - T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
Memory:
 - Single memory controller capable of supporting DDR3 and DDR3-LV devices
 - Two DDR3 DIMMs up to 4GB, Dual rank @ 2133MT/s and ECC support
Ethernet interfaces:
 - Two 1Gbps RGMII on-board ports
 - Four 10Gbps XFI on-board cages
 - 1Gbps/2.5Gbps SGMII Riser card
 - 10Gbps XAUI Riser card
Accelerator:
 - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes:
 - 16 lanes up to 10.3125GHz
 - Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
IFC:
 - 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
eSPI:
 - Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
USB:
 - Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB)
PCIE:
 - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
SATA:
 - Two SATA 2.0 ports on-board
SRIO:
 - Two Serial RapidIO 2.0 ports up to 5 GHz
eSDHC:
 - Supports SD/SDHC/SDXC/eMMC Card
I2C:
 - Four I2C controllers.
UART:
 - Dual 4-pins UART serial ports
System Logic:
 - QIXIS-II FPGA system controll
Debug Features:
 - Support Legacy, COP/JTAG, Aurora, Event and EVT

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: removed Makefile blank line at EOF,
           fix conflicts with moving DDR driver]
Acked-by: York Sun <yorksun@freescale.com>
2013-11-25 12:36:11 -08:00
Shengzhou Liu
629d6b32d6 powerpc/mpc85xx: Add T2080/T2081 SoC support
Add support for Freescale T2080/T2081 SoC.

T2080 includes the following functions and features:
- Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz
- 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- Hierarchical interconnect fabric
- One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- 16 SerDes lanes up to 10.3125 GHz
- 8 mEMACs for network interfaces (four 1Gbps MACs and four 10Gbps/1Gbps MACs)
- High-speed peripheral interfaces
  - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
  - Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- Additional peripheral interfaces
  - Two serial ATA (SATA 2.0) controllers
  - Two high-speed USB 2.0 controllers with integrated PHY
  - Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC)
  - Enhanced serial peripheral interface (eSPI)
  - Four I2C controllers
  - Four 2-pin UARTs or two 4-pin UARTs
  - Integrated Flash Controller supporting NAND and NOR flash
- Three eight-channel DMA engines
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0

Differences between T2080 and T2081:
  Feature               T2080 T2081
  1G Ethernet numbers:  8     6
  10G Ethernet numbers: 4     2
  SerDes lanes:         16    8
  Serial RapidIO,RMan:  2     no
  SATA Controller:      2     no
  Aurora:               yes   no
  SoC Package:          896-pins 780-pins

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-11-25 11:44:25 -08:00
Shengzhou Liu
82a55c1ef8 net/fman: Add support for 10GEC3 and 10GEC4
There are more than two 10GEC in single FMAN in some SoCs(e.g. T2080).
This patch adds support for 10GEC3 and 10GEC4.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2013-11-25 11:43:47 -08:00
York Sun
0b66513b27 Driver/IFC: Move Freescale IFC driver to a common driver
Freescale IFC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the driver to driver/misc
and fix the header file includes.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-11-25 11:43:47 -08:00
York Sun
00ec3fd211 Driver/DDR: Update DDR driver to allow non-zero base address
The DRAM base has been zero for Power SoCs. It could be non-zero
for ARM SoCs. Use a macro instead of hard-coding to zero.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-11-25 11:43:47 -08:00
York Sun
d4263b8adb powerpc/mpc8xxx: Extend DDR registers' fields
Some DDR registers' fields have expanded to accommodate larger values.
These changes are backward compatible. Some fields are removed for newer
DDR controllers. Writing to those fields are safely ignored.

TIMING_CFG_2 register is fixed. Additive latency is added to RD_TO_PRE
automatically. It was a misunderstanding in commit c360ceac.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-11-25 11:43:46 -08:00
York Sun
9ac4ffbde1 Driver/DDR: Add Freescale DDR driver for ARM
Make PowerPC specific code conditional so ARM SoCs can reuse
this driver. Add DDR3 driver for ARM.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-11-25 11:43:46 -08:00
York Sun
9a17eb5b7e Driver/DDR: combine ccsr_ddr for 83xx, 85xx and 86xx
Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3
structure for 83xx, 85xx and 86xx.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-11-25 11:43:46 -08:00
York Sun
5614e71b49 Driver/DDR: Moving Freescale DDR driver to a common driver
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-11-25 11:43:43 -08:00
Zhao Qiang
ac6880782d p1010rdb: enable mtdparts for NAND
The default partition table matches the .dts files for these boards in
Linux.  This allows these partitions to be used by name with U-Boot's
"nand" command.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
2013-11-25 11:40:05 -08:00
Tang Yuantian
f40fcfd911 mpc85xx: Fix the offset of register address error
The offset of register address within GPIO module is just
CONFIG_SYS_MPC85xx_GPIO_ADDR. So, fix it. The following platforms
are confirmed: MPC8572, P1023, P1020, P1022, P2020, P4080,
P5020, P5040, T4240, B4860.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
2013-11-25 11:40:05 -08:00
Priyanka Jain
15d89961a0 powerpc/t1040qds: Correct Maintainer name in boards.cfg
Update T1040QDS naem to Poonam Aggrwal.

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
2013-11-25 11:40:05 -08:00
Tom Rini
74279d3761 Merge branch 'sandbox1' of http://git.denx.de/u-boot-x86 2013-11-25 10:42:53 -05:00
Tom Rini
1a1326d2da Merge branch 'master' of git://git.denx.de/u-boot-net 2013-11-25 10:42:19 -05:00
Tom Rini
faca8ff55f Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2013-11-25 10:42:13 -05:00
Tom Rini
5a4fe1aaf1 Merge branch 'buildpatman' of http://git.denx.de/u-boot-x86 2013-11-25 10:42:05 -05:00
Tom Rini
e8a8bab52c sparc: Correct arch/sparc/cpu/leon3/start.S from SPDX conversion
The SPDX tag conversion ate part of this file, put things back to the
way they should be.

Signed-off-by: Tom Rini <trini@ti.com>
2013-11-25 10:41:55 -05:00
Wolfgang Denk
a5750b8058 blackfin: don't use 'bool' when it causes problems
The use of 'bool' data types in globally used header files cases build
errors like this:

In file included from arch/blackfin/include/asm/blackfin.h:13:0,
                 from include/common.h:92,
                 from cmd_test.c:17:
arch/blackfin/include/asm/blackfin_local.h:54:1: error: unknown type name 'bool'

Use plain 'int' instead to avoid such kind of trouble.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-11-25 10:41:55 -05:00
Masahiro Yamada
4d1584bd0d MAKEALL: add -b (--board) option
Some board have multiple configurations.
For example, the board "m54455evb" has many configurations:
M54455EVB, M54455EVB_a66, M54455EVB_i66, M54455EVB_intel, ...

When we modify board-related files, we need to test
all configurations based on such a board.

In such a case, the new option -b is useful.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-25 10:41:54 -05:00
Masahiro Yamada
f6bab6710c bios_emulator: delete an unnecessary include path
-I$(TOPDIR)/include is defined in the top config.mk.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-25 10:41:54 -05:00
Masahiro Yamada
5310b8b2a8 nand_spl: trivial refactoring of makefiles
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-25 10:41:54 -05:00
Masahiro Yamada
ad420282e2 Makefile: descend into subdirectories only when CONFIG_API is defined
All objects under api/ and examples/api/ directories are selected
by CONFIG_API.
So we can move CONFIG_API switch to the top Makefile.

In order to use CONFIG_API, the definition of SUBDIR_EXAMPLES-y
must be moved after "sinlude $(obj)include/autoconf.mk".

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-25 10:41:54 -05:00
Masahiro Yamada
017ce20f46 common: Delete unnecessary rules.
The directory tools/ is always built before common/.
So when envcrc tool is necessary in common/Makefile,
it already exists.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-25 10:41:54 -05:00
Masahiro Yamada
3c6dc17eae drivers: delete unnecessary HOSTCFLAGS
HOSTCFLAGS is meaningless because no host programs
are compiled there.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-25 10:41:54 -05:00
Masahiro Yamada
fdc36977b3 Makefile: move some libraries to lib/Makefile
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-25 10:41:54 -05:00
Masahiro Yamada
8a7e7d5697 Makefile: descend into subdirectories only when CONFIG_API is defined
All objects under api/ and examples/api/ directories are selected
by CONFIG_API.
So we can move CONFIG_API switch to the top Makefile.

In order to use CONFIG_API, the definition of SUBDIR_EXAMPLES-y
must be moved after "sinlude $(obj)include/autoconf.mk".

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-25 10:41:53 -05:00
Masahiro Yamada
fdb87049d8 examples: delete unnecessary CPPFLAGS
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-25 10:41:53 -05:00
Masahiro Yamada
dbfb4cb52f board: tqm5200: delete its own object make rule
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-25 10:41:53 -05:00
Masahiro Yamada
72b97e4bc9 spieval: Remove remainders of dead board
Commit 69434e4c deleted spieval board support
but it missed to clean up include/configs/spieval.h file.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-25 10:41:53 -05:00
Masahiro Yamada
0e53691529 post: remove unnecessary include path settings
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-25 10:41:53 -05:00
Masahiro Yamada
1500389c2f board: h2200: Delete an unnecessary make rule
We have a generic rule to generate .o file from *.S
in $(TOPDIR)/config.mk.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-25 10:41:53 -05:00
Masahiro Yamada
2e78e75e1f tools: updater: Remove remainders of dead board
tools/updater needs board/MAI/AmigaOneG3SE board
for compiling.
But AmigaOneG3SE board was already deleted
by Commit 953b7e6.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-25 10:41:53 -05:00
Masahiro Yamada
cfe19f917a tools: imls: Remove a broken and unused tool.
It looks like tools/imls/Makefile is invoked from nowhere.
And also it is broken.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-25 10:41:52 -05:00
Igor Grinberg
9dfdcdfed4 gpio_led: add support for inverted polarity
Some GPIO connected LEDs have inverted polarity.
Introduce new config option: CONFIG_GPIO_LED_INVERTED_TABLE for the
specifying the inverted GPIO LEDs list and add support for this in the
gpio_led driver.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Ilya Ledvich <ilya@compulab.co.il>
2013-11-25 10:41:52 -05:00
Igor Grinberg
6516f81b64 gpio_led: check gpio_request() return value
Add a check for the gpio_request() function return value and do not try
to configure the GPIO if the gpio_request() call fails.
Also, print an error message indicating the gpio_request() has failed.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Ilya Ledvich <ilya@compulab.co.il>
2013-11-25 10:41:52 -05:00
Igor Grinberg
1df7bbba24 README: document the CONFIG_GPIO_LED symbol
The CONFIG_GPIO_LED symbol does not have any documentation in the README
file. Document the CONFIG_GPIO_LED symbol.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-11-25 10:41:52 -05:00