Use proper register base and access method to access GRF registers.
GRF registers start at a completely different base, and need special
access method, that sets the change mask in the 16 MSBs.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
If phy is not defined in DT (eg. on rk3399), generic_phy_get_by_name
will return -ENODATA. Handle that case correctly.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
pllref_clk is unused after being retrieved. fin needs to be set
to dsi->ref clock's rate for the following calculation to work.
Otherwise fin is undefined, and calculation return bogus number
based on undefined variable.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
&priv->phy is always true. Compiler warns about this loudly.
Use a propper check for phy device allocation. Without this fix
using this driver with SoC that doesn't use external phy (eg. RK3399)
doesn't work.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
These must be read from timings->flags, like other DSI HOST drivers do.
And they must not be inverted either. Low means low.
Without this fix, panel drivers that set *SYNC_LOW produce corrupted
output on screen (shifted horizontally and vertically by back porch
distance).
Signed-off-by: Ondrej Jirman <megi@xff.cz>
The intermediate value could overflow for large periods and levels.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver is for panels based on the Himax HX8394 controller, such as the
HannStar HSD060BHW4 720x1440 TFT LCD panel that uses a MIPI-DSI interface.
This panel is used in Pinephone Pro.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Cc: Anatolij Gustschin <agust@denx.de>
Some callers expect to call this with NULL font name to select the
default font (eg. boot/scene.c). Without handling the NULL condition
U-Boot crashes instead of displaying a bootflow GUI menu.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Cc: Anatolij Gustschin <agust@denx.de>
The sar-reg0 alias was left over from an earlier iteration of the
patches adding support for this board. Remove the unused alias.
Fixes: 6cc8b5db40 ("arm: mvebu: Add RD-AC5X board")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The x240 and SE240 are a series of L2+ switches from Allied Telesis.
There are a number of them in the range but as far as U-Boot is
concerned all the CPU block components are the same so there's only one
board defined.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently, a random MAC address is assigned to eth1 in Linux.
Fix this behavor by retrieving the second MAC address from the fuses.
Signed-off-by: Fabio Estevam <festevam@denx.de>
On the XEA (imx287) system the FAT file system is not used neither in
SPL nor u-boot proper.
Hence, to save ~6KiB of u-boot.img size - it has been disabled.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The XEA system (imx287 based) is not using support for EXTLINUX and VBE.
As those configuration options have been enabled by default with modern
Kconfig it is safe to explicitly disable them.
After that change the u-boot.img size has been reduced by ~16 KiB.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Drive CTRL_SLEEP_MOCI# high at boot (SPL) using a GPIO hog, this signal
may be used to control some power-rails on the carrier board, therefore
it should be set to high when the module is booting.
To do this as early as possible is generally a good idea and the issue
was noticed on the Yavia carrier board where it is needed to power the
I2C EEPROM on the carrier board.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Enable CONFIG_SPL_GPIO_HOG option to be able to control GPIO hogs from
SPL.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drive CTRL_SLEEP_MOCI# high at boot (SPL) using a GPIO hog, this signal
may be used to control some power-rails on the carrier board, therefore
it should be set to high when the module is booting.
To do this as early as possible is generally a good idea and the issue
was noticed on the Yavia carrier board where it is needed to power the
I2C EEPROM on the carrier board.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Enable CONFIG_SPL_GPIO_HOG option to be able to control GPIO hogs from
SPL.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The USB Power domains should not have been removed as it causes
the board to hang if the USB is started.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Several changes have been made to the device tree
in the kernel, so update that as well as the
corresponding imx8mp-u-boot.dtsi files to prevent
breaking the booting.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
There are some newer clocks added to the kernel recently,
so to fix prepare for resycing the device trees, update
the clock list. Since there are some minor changes to
the USB clocks, update which USB clocks are enabled
to match with the upstream kernel as well.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
For SOM with the EC configuration, the ethernet PHY is located on the
SOM itself, and connected to the CPU ethernet controller. It has a
reset line controlled via GPIO1_IO9. In this configuration, the PHY
located on the carrier board is not connected to anything and is
therefore not used.
For SOM without EC configuration, the ethernet PHY on the carrier
board is connected to the CPU ethernet controller. It has a reset line
controlled via the GPIO expander PCA9534_IO5.
The hardware configuration (EC) is determined at runtime by
reading from the SOM EEPROM.
To support both hardware configurations (EC and non-EC), adjust/fix
the PHY reset gpios according to the hardware configuration
read at runtime from the SOM EEPROM. This adjustement is done in
U-Boot (OF_BOARD_FIXUP) and kernel (OF_BOARD_SETUP) device trees.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
In case the i.MX8M Plus starts from eMMC BOOT1/BOOT2 HW partitions, the
flash.bin container is stored at offset 0 from the start, that means the
fitImage itb is at offset 0x2c0 instead of 0x300 sectors from the start.
Handle this difference in custom spl_mmc_get_uboot_raw_sector() .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Bitwise operations on signed integers are not defined,
replace them with per-call checks.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
In order to enable HAB, FSL_CAAM, ARCH_MISC_INIT and
SPL_CRYPTO should be enabled in Kconfig like other i.MX8M
boards.
This also needs to occur in the SPL so enable CONFIG_SPL_BOARD_INIT and
add a void spl_board_init function which calls arch_misc_init to probe
the CAAM driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Update RAM Timings for 2GB RAM based on DDR Controller Configuration
Spreadsheet revision 22. Including the update of the refresh
rate to workaround errata ERR050805.
Signed-off-by: Cem Tenruh <c.tenruh@phytec.de>
The csf_spl.txt and csf_fit.txt templates contain file paths which must
be edited for the location of your NXP CST generated key files.
Streamline the process of signing an image by assigning unique var names
to these which can be expended from env variables in the csf.sh script.
The following vars are used:
SRK_TABLE - full path to SRK_1_2_3_4_table.bin
CSF_KEY - full path to the CSF Key CSF1_1_sha256_4096_65537_v3_usr_crt.pem
IMG_KEY - full path to the IMG Key IMG1_1_sha256_4096_65537_v3_usr_crt.pem
Additionally provide an example of running the csf.sh script.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The sec_in32 preprocessor is defined as follows in include/fsl_sec.h file:
When address "a" is calculated using math for ex: addition of base address and
an offset, then casting is applied only to the first address which in this
example is base address.
caam_ccbvid_reg = sec_in32(CONFIG_SYS_FSL_SEC_ADDR + CAAM_CCBVID_OFFSET)
resolves to:
caam_ccbvid_reg = in_le32((ulong *)(ulong)CONFIG_SYS_FSL_SEC_ADDR +
CAAM_CCBVID_OFFSET)
instead it should resolve to:
caam_ccbvid_reg = in_le32((ulong *)(ulong)(CONFIG_SYS_FSL_SEC_ADDR +
CAAM_CCBVID_OFFSET))
Thus add parenthesis around the address "a" so that however the address is
calculated, the casting is applied to the final calculated address.
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
add support for SHA-256 secure hash algorithm using the ARM v8
SHA-256 instructions for verifying image hash.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Abstract common interfaces for AHAB authentication operations.
Then share some common codes for AHAB and SPL container authentication
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If the container has image which conflicts with
spl_get_load_buffer address, there are processing failures.
Use malloc instead of spl_get_load_buffer.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Nitin Garg <nitin.garg@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
