When using the USB OTG FEL mode on the Allwinner H616, the BootROM
stores some data at the end of SRAM C. This is also the location where
we place the initial SPL stack, so it will overwrite this data.
We still need the BROM code after running the SPL, so should leave that
area alone.
Interestingly this does not seem to have an adverse effect, I guess on
the "way out" (when we return to FEL after the SPL has run), this data
is not needed by the BROM, for just the trailing end of the USB operation.
However this is still wrong, and we should not clobber BROM data.
Lower the SPL stack address to be situated right below the swap buffers
we use in sunxi-fel: that should be out of the way of everyone else.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
At this point in the conversion there should be no need to have logic to
disable some symbol during the SPL build as all symbols should have an
SPL counterpart.
The main real changes done here are that we now must make proper use of
CONFIG_IS_ENABLED(DM_SERIAL) rather than many of the odd tricks we
developed prior to CONFIG_IS_ENABLED() being available.
Signed-off-by: Tom Rini <trini@konsulko.com>
There is a CONFIG_MMC_SUNXI_SLOT definition in our sunxi_common.h config
header, which was used to note the first MMC controller to initialise.
The definition in that header was always set to 0, with no easy way of
overriding this, and certainly none of the existing boards made any use
of that (non-)feature.
Remove that definition and replace it with a constant 0 in the only
user, in board.c. It turns out that this is safe, as this is only used
in the SPL, and the BROM also unconditionally initialises MMC0.
This also removes the last legacy config symbol with SUN*I in it from
the whitelist.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NS16550
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SPL_NS16550_MIN_FUNCTIONS
CONFIG_SYS_NS16550_MEM32
CONFIG_SYS_NS16550_PORT_MAPPED
CONFIG_SYS_NS16550_REG_SIZE
CONFIG_SYS_NS16550_SERIAL
To do this we also introduce CONFIG_SPL_SYS_NS16550_SERIAL so that
platforms can enable the legacy driver here for SPL.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_MAX_OOBFREE
CONFIG_SYS_NAND_MAX_ECCPOS
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN
To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_MMC_MAX_DEVICE
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This converts the following to Kconfig:
CONFIG_SYS_MAX_NAND_DEVICE
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The default load addresses for the various payloads (kernel, DT,
ramdisk) on systems with just 32MB of DRAM have some issues:
For a start the preceding comment doesn't match the actual values:
apparently they were copied from the 64MB S3 layout, then halved, but
since 0x5 is NOT the half of 0x10, they don't match up.
Also those projected maximum sizes are quite restrictive: it's not easy
to build a compressed kernel image with just 4MB. The only defconfig in
mainline Linux that supports the F1C100s (the only 32MB user so far)
creates a 6MB compressed / 15MB uncompressed kernel.
Rearrange the default load addresses to accommodate such a kernel: we
allow an 7MB/16MB kernel, and up to 5MB of ramdisk, stuffing the smaller
binaries like the DTB towards the end, just before the relocated U-Boot.
Shrink the size for DTB and scripts on the way, there is no need for
allowing up to 512K for them.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Traditionally we assumed that every Allwinner board would come with at
least 256 MB of DRAM, and set our DRAM layout accordingly. This affected
both the default load addresses, but also U-Boot's own address
expectations (like being loaded at 160 MB).
Some SoCs come with co-packaged DRAM, but only provide 32 or 64MB. So
far we special-cased those *chips*, as there was only one chip per DRAM
size. However new chips force us to take a more general approach.
Introduce a Kconfig symbol, which provides the minimum DRAM size of the
board. If nothing else is specified, we use 256 MB, and default to
smaller values for those co-packaged SoCs.
Then select the different DRAM maps according to this new symbol, so
that different SoCs with the same DRAM size can share those definitions.
Inspired by an idea from Icenowy.
This is just refactoring: compiled for all boards before and after this
patch: the binaries were identical.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
This converts the following to Kconfig:
CONFIG_SYS_BOOTM_LEN
As part of this, rework error handling in boot/bootm.c so that we pass
the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not
be available to host tools but we do know the size that we passed to
malloc().
Cc: Soeren Moch <smoch@web.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_OHCI_SWAP_REG_ACCESS
CONFIG_SYS_USB_OHCI_CPU_INIT
CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS
CONFIG_SYS_USB_OHCI_SLOT_NAME
CONFIG_USB_ATMEL
CONFIG_USB_ATMEL_CLK_SEL_PLLB
CONFIG_USB_ATMEL_CLK_SEL_UPLL
CONFIG_USB_OHCI_LPC32XX
CONFIG_USB_OHCI_NEW
Signed-off-by: Tom Rini <trini@konsulko.com>
- Ensure that everyone setting mtdids= and mtdparts= is doing so via the
CONFIG options.
- If the CONFIG options are set, ensure that the default environment
sets mtdparts / mtdids.
Signed-off-by: Tom Rini <trini@konsulko.com>
With the exception of how PowerPC handles SPL and TPL (which has its own
issues), we cannot safely hide options under CONFIG_SPL_BUILD. Largely
remove the places that have this test today.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOARD_SIZE_LIMIT
To do this, introduce CONFIG_HAS_BOARD_SIZE_LIMIT.
Signed-off-by: Tom Rini <trini@konsulko.com>
We cannot define a CONFIG value here to ensure that the Kconfig value
isn't set wrong.
Fixes: 2c699fe0d3 ("configs: sunxi: Add common SUNIV header")
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Adds support for SUNIV and the F1C100s.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Remove some pointless #ifdefs from this file, as there are quite too
many of them already.
Some definitions don't really hurt to have in any case, so remove the
pointless CONFIG_MMC guard around CONFIG_MMC_SUNXI_SLOT.
The BOARD_SIZE_LIMIT applies regardless of ARM64 or not (now), so remove
that guard as well. The maximum number of MMC devices does not depend on
CONFIG_ENV_IS_IN_MMC, so move that out to simplify the file.
Last but not least CONFIG_SPL_BOARD_LOAD_IMAGE serves no real purpose
anymore: it's unconditionally defined for all sunxi boards, and protects
nothing applicable outside of sunxi code anymore. Just remove it.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Two displays supported by the sunxi display driver (each one used by a
single board) require initialization over I2C. Both previously used
i2c_soft; replace this with the i2c-gpio instance that already exists in
those boards' device trees (sun5i-a13-utoo-p66 and sun6i-a31-colombus).
Since the i2c-gpio nodes are not referenced by any other node in the
device trees (the device trees have no panel node), the I2C bus is
selected by its node name.
This panel initialization code was the only i2c_soft user, so the
i2c_soft GPIO setup code can be removed now as well.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As this is only useful when booting with ATAGs, which are now largely
disabled, remove this value for the remaining platforms. We have a few
places in the code that had been testing for MACH_TYPE as a sort of
internal logic. Update those to use different but still correct CONFIG
symbols.
Cc: Phil Sutter <phil@nwl.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL. Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to
one or more symbols.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_I2C_SOFT
CONFIG_SYS_I2C_SOFT_SPEED
CONFIG_SYS_I2C_SOFT_SLAVE
Signed-off-by: Tom Rini <trini@konsulko.com>
It is quite confusing that CONFIG_SYS_I2C selects the legacy I2C and
CONFIG_DM_I2C selects the current I2C. The deadline to migrate I2C is less
than a year away.
Also we want to have a CONFIG_I2C for U-Boot proper just like we have
CONFIG_SPL_I2C for SPL, so we can simplify the Makefile rules.
Rename this symbol so it is clear it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The "booti" command to load arm64 Linux kernels supports automatic
decompression of zipped kernel images, but relies on some environment
variables to point to usable buffer RAM.
Add those variables and let them point to some default values, that
should cover most use-cases.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Commit 69076dff22 ("cmd: pxe: add support for FDT overlays") added
support for loading DT overlay files to PXE boot. However, it needs
additional environment variable which points to memory location which
can be used to temporary store overlay data.
Add it and in the process unify alignment using spaces and fix comment.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
DM_VIDEO migration deadline is already expired, but around
80 Allwinner boards are still using video in a legacy way:
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Convert the legacy video driver over to the DM_VIDEO framework. This is
a minimal conversion: it doesn't use the DT for finding its resources,
nor does it use DM clocks or DM devices for the outputs (LCD, HDMI, CVBS).
Tested in Bananapi M1+ Plus 1920x1200 HDMI out. (Jagan)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Andre: rebase and smaller fixes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
