Commit graph

1948 commits

Author SHA1 Message Date
Stefan Agner
f9c39d95f1 doc: add Serial Download Protocol documentation
Document the U-Boot Serial Download Protocol implementation and
some typical use cases.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
2017-08-23 10:41:58 +02:00
Patrice Chotard
4fadcaf097 i2c: add i2c driver for stm32
Add i2c driver which can be used on both STM32F7 and STM32H7.
This I2C block supports the following features:
 _ Slave and master modes
 _ Multimaster capability
 _ Standard-mode (up to 100 kHz)
 _ Fast-mode (up to 400 kHz)
 _ Fast-mode Plus (up to 1 MHz)
 _ 7-bit and 10-bit addressing mode
 _ Multiple 7-bit slave addresses (2 addresses, 1 with configurable mask)
 _ All 7-bit addresses acknowledge mode
 _ General call
 _ Programmable setup and hold times
 _ Easy to use event management
 _ Optional clock stretching
 _ Software reset

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-23 07:04:40 +02:00
Tom Rini
09b6a6dd01 Merge git://git.denx.de/u-boot-usb 2017-08-21 07:16:56 -04:00
Lukasz Majewski
5bf4475f1d doc: license: Add license header to the README.dfutftp file
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-08-21 11:31:11 +02:00
Masahiro Yamada
00aa453ebf ARM: uniphier: remove sLD3 SoC support
This SoC is too old.  It is difficult to maintain any longer.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-20 23:05:39 +09:00
Simon Glass
35affd7a2f env: Rename eth_getenv_enetaddr() to eth_env_get_enetaddr()
Rename this function for consistency with env_get().

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:30:44 -04:00
Simon Glass
fd1e959e91 env: Rename eth_setenv_enetaddr() to eth_env_set_enetaddr()
Rename this function for consistency with env_set().

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:23:56 -04:00
Simon Glass
382bee57f1 env: Rename setenv() to env_set()
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:22:18 -04:00
Sam Protsenko
5abc1a4523 common: Move CONFIG_BOOTARGS to Kconfig
Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 17:06:06 -04:00
Tom Rini
c1b62ba9ca Merge branch 'master' of git://git.denx.de/u-boot-rockchip 2017-08-14 10:40:01 -04:00
Bin Meng
7088a36598 x86: qemu: Enable NVMe driver
QEMU supports NVMe emulation. Enable the NVMe driver on QEMU x86.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-13 15:17:33 -04:00
Zhikang Zhang
0adc38be3d nvme: Add nvme commands
Add nvme commands in U-Boot command line.

1. "nvme scan" - scan NVMe blk devices
2. "nvme list" - show all available NVMe blk devices
3. "nvme info" - show current or a specific NVMe blk device
4. "nvme device" - show or set current device
5. "nvme part" - print partition table
6. "nvme read" - read data from NVMe blk device
7. "nvme write" - write data to NVMe blk device

Signed-off-by: Zhikang Zhang <zhikang.zhang@nxp.com>
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-13 15:17:32 -04:00
Zhikang Zhang
982388eaa9 nvme: Add NVM Express driver support
NVM Express (NVMe) is a register level interface that allows host
software to communicate with a non-volatile memory subsystem. This
interface is optimized for enterprise and client solid state drives,
typically attached to the PCI express interface.

This adds a U-Boot driver support of devices that follow the NVMe
standard [1] and supports basic read/write operations.

Tested with a 400GB Intel SSD 750 series NVMe card with controller
id 8086:0953.

[1] http://www.nvmexpress.org/resources/specifications/

Signed-off-by: Zhikang Zhang <zhikang.zhang@nxp.com>
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-13 15:17:31 -04:00
Philipp Tomsich
403e9cbcd5 rockchip: rk3368: add DRAM controller driver with DRAM initialisation
This adds a DRAM controller driver for the RK3368 and places it in
drivers/ram/rockchip (where the other DM-enabled DRAM controller
drivers for rockchip devices should also be moved eventually).

At this stage, only the following feature-set is supported:
 - DDR3
 - 32-bit configuration (i.e. fully populated)
 - dual-rank (i.e. no auto-detection of ranks)
 - DDR3-1600K speed-bin

This driver expects to run from a TPL stage that will later return to
the RK3368 BROM.  It communicates with later stages through the
os_reg2 in the pmugrf (i.e. using the same mechanism as Rockchip's DDR
init code).

Unlike other DMC drivers for RK32xx and RK33xx parts, the required
timings are calculated within the driver based on a target frequency
and a DDR3 speed-bin (only the DDR3-1600K speed-bin is support at this
time).

The RK3368 also has the DDRC0_CON0 (DDR ch. 0, control-register 0)
register for controlling the operation of its (single-channel) DRAM
controller in the GRF block.  This provides for selecting DDR3, mobile
DDR modes, and control low-power operation.
As part of this change, DDRC0_CON0 is also added to the GRF structure
definition (at offset 0x600).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:33 +02:00
Philipp Tomsich
ee14d29db0 rockchip: back-to-bootrom: split BACK_TO_BOOTROM for TPL/SPL
The back-to-bootrom option is rather unfortunately named
  CONFIG_ROCKCHIP_SPL_BACK_TO_BOOTROM
instead of
  CONFIG_SPL_ROCKCHIP_BACK_TO_BOOTROM

To make is selectable through CONFIG_IS_ENABLED(ROCKCHIP_BACK_TO_BOOTROM),
we need to rename it.  At the same time, we introduce a TPL_ variant of
the option to give us finer-grained control over when it should be used.

This change is motivated by our RK3368 boot process, which returns to
the boot ROM only from the TPL stage, but not from the SPL stage.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[added fix-up for evb-rk3229_defconfig and phycore-rk3288_defconfig:]
[fixed inverted CONFIG_IS_ENABLED test for rk3288:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

include/configs/rock.h: undef
2017-08-13 17:12:19 +02:00
Alison Chaiken
203f9b48ad GPT: provide commands to selectively rename partitions
This patch provides support in u-boot for renaming GPT
partitions.  The renaming is accomplished via new 'gpt swap'
and 'gpt rename' commands.

The 'swap' mode returns an error if no matching partition names
are found, or if the number of partitions with one name does not equal
the number with the second name.   The 'rename' variant always
succeeds as long as a partition with the provided number exists.

Rewriting the partition table has the side-effect that all partitions
end up with "msftdata" flag set.  The reason is that partition type
PARTITION_BASIC_DATA_GUID is hard-coded in the gpt_fill_pte()
function.  This does not appear to cause any harm.

Signed-off-by: Alison Chaiken <alison@peloton-tech.com>
2017-08-04 20:35:27 -04:00
Alison Chaiken
73d6d18b71 GPT: add accessor function for disk GUID
In order to read the GPT, modify the partition name strings, and then
write out a new GPT, the disk GUID is needed.  While there is an
existing accessor for the partition UUIDs, there is none yet for the
disk GUID.

Changes since v6: none.

Signed-off-by: Alison Chaiken <alison@peloton-tech.com>
2017-08-04 09:56:04 -04:00
Alison Chaiken
52791db74f cmd gpt: test in sandbox
Make minor changes to README.gpt and sandbox_defconfig to support
testing of the gpt command's functionality in the sandbox.

Changes since v6: none.

Signed-off-by: Alison Chaiken <alison@peloton-tech.com>
2017-08-04 09:56:02 -04:00
Alison Chaiken
0a24238625 GPT: fix error in partitions string doc
The existing partitions-list parsing in cmd/gpt.c passes a value
from gpt_default() to set_gpt_info() that README.gpt suggests
should begin with 'partitions='.  Partition-list strings should
in fact begin with 'uuid_disk', as otherwise the call from
set_gpt_info() to extract_val() to find 'uuid_disk' will fail.
Change README.gpt accordingly.

Changes since v6: none.

Signed-off-by: Alison Chaiken <alison@peloton-tech.com>
2017-08-04 09:55:30 -04:00
Andy Shevchenko
495f3774be x86: Add Intel Edison board files
Add Intel Edison board which is using U-Boot.

The patch is based on work done by the following people (in alphabetical
order):
	Aiden Park <aiden.park@intel.com>
	Dukjoon Jeon <dukjoon.jeon@intel.com>
	eric.park <eric.park@intel.com>
	Fabien Chereau <fabien.chereau@intel.com>
	Felipe Balbi <felipe.balbi@linux.intel.com>
	Scott D Phillips <scott.d.phillips@intel.com>
	Sebastien Colleur <sebastienx.colleur@intel.com>
	Steve Sakoman <steve.sakoman@intel.com>
	Vincent Tinelli <vincent.tinelli@intel.com>

In case we're building for Intel Edison, we must have 4096 bytes of
zeroes in the beginning on u-boot.bin. This is done in
board/intel/edison/config.mk.

First run sets hardware_id environment variable which is read from
System Controller Unit (SCU).

Serial number (serial# environment variable) is generated based on eMMC
CID.

MAC address on USB network interface is unique to the board but kept the
same all over the time.

Set mac address from U-Boot using following scheme:
	OUI = 02:00:86
	next 3 bytes of MAC address set from eMMC serial number

This allows to have a unique mac address across reboot and flashing.

Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[bmeng: Add MAINTAINERS file for Intel Edison board]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-30 10:30:25 +08:00
Tom Rini
f19955a014 Merge git://git.denx.de/u-boot-uniphier 2017-07-26 11:29:25 -04:00
Tom Rini
25fa0b930f FIT: List kernel_noload in the list of types
In the source_file_format.txt file we talk about how to construct a
valid FIT image.  While it already says to look at the source for the
full list, add kernel_noload to the explicit list of types.  This is
arguably the most important type to use as most often we are including a
kernel that will run from wherever it is loaded into memory and execute.

This for example, allows you to create a single FIT image for Linux that
can be used on both OMAP and i.MX devices as the kernel will not need to
be moved in memory.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-26 11:29:15 -04:00
Patrice Chotard
f303aaf21b ram: stm32: add second SDRAM bank management
FMC is able to manage 2 SDRAM banks, but the current driver
implementation is only able to manage the first SDRAM bank.

Even if only bank2 is used, some bank1 registers must be
configured.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-07-26 11:29:15 -04:00
Masahiro Yamada
673ac334fc doc: uniphier: rework README.uniphier
Rework the readme to reflect the latest boot mechanism on ARMv8 SoCs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-07-26 22:27:15 +09:00
Masahiro Yamada
ee8d037ce7 ARM: uniphier: remove SPL support for ARMv8 SoCs
It has been a while since ARM Trusted Firmware supported UniPhier SoC
family.  U-Boot SPL was intended as a temporary loader that runs in
secure world.  It is a maintenance headache to support two different
boot mechanisms.  Secure firmware is realm of ARM Trusted Firmware
and now U-Boot only serves as a non-secure boot loader for UniPhier
ARMv8 SoCs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-07-26 22:27:15 +09:00
Tom Rini
39632b4a01 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2017-07-18 08:42:48 -04:00
Stefano Babic
552a848e4f imx: reorganize IMX code as other SOCs
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.

This change is also coherent with the structure in kernel.

Signed-off-by: Stefano Babic <sbabic@denx.de>

CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2017-07-12 10:17:44 +02:00
Peng Fan
f34ccce50a mmc: fsl_esdhc: drop CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT
CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT is not the correct method
to set I/O to 1.8. To boards that does not support vqmmc-supply,
use vs18_enable in fsl_esdhc_cfg. If regulator is supported,
use fixed 1.8V regulator for vqmmc-supply.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-07-12 09:44:22 +02:00
Igal Liberman
b6518b1ea3 arm64: mvebu: use single defconfig for Armada8K development boards
Currently, Marvell Armada8k development board use 3 different
defconfigs:
        mvebu_db-88f7040-nand_defconfig
        mvebu_db-88f7040_defconfig
        mvebu_db-88f8040_defconfig
Having 3 different defconfigs makes maintenance difficult.

This patch removes the defconfigs mentioned above and introduce
a new defconfig which represents the Armada8k family.

NOTE:
In order not to break automatic tools compilation,
a default device-tree is set in the defconfig (armada-8040-db).
However, when compiling u-boot, the user MUST explicitly export
the DEVICE_TREE for the requested board because using A80x0
device-tree on A70x0 might break the device.

For more information, refer to "doc/README.marvell" (intoduced
in this patch).

Change-Id: I98515b6306498358f3722ecf7ac4c87f236ebbd8
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-07-12 06:57:55 +02:00
Tom Rini
8d3a25685e Merge git://git.denx.de/u-boot-dm 2017-07-11 20:28:46 -04:00
Simon Glass
2cce586651 dtoc: Support multiple compatible strings in a node
Sometimes a node will have multiple compatible strings. Drivers may use
one or the other so the best approach seems to be to #define them to be
equivalent.

Update dtoc to support this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
2017-07-11 10:08:19 -06:00
Alison Chaiken
564cf25d5b cmd gpt: test in sandbox
Make minor changes to README.gpt and sandbox_defconfig to support
testing of the gpt command's functionality in the sandbox.

Signed-off-by: Alison Chaiken <alison@peloton-tech.com>
2017-07-11 10:08:19 -06:00
Wadim Egorov
a84b589e5d doc: rockchip: Add phyCORE-RK3288 RDK to board list
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-07-11 15:23:38 +02:00
Andy Shevchenko
daab59ac05 avr32: Retire AVR32 for good
AVR32 is gone. It's already more than two years for no support in Buildroot,
even longer there is no support in GCC (last version is heavily patched 4.2.4).

Linux kernel v4.12 got rid of it (and v4.11 didn't build successfully).

There is no good point to keep this support in U-Boot either.

Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2017-07-06 16:17:19 -04:00
Heiko Schocher
98f705c9ce powerpc: remove 4xx support
There was for long time no activity in the 4xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 4xx,
so remove it.

Signed-off-by: Heiko Schocher <hs@denx.de>
2017-07-03 17:35:28 -04:00
Christophe Leroy
7826669df8 doc: restore doc/README.fsl-clk
doc/README.fsl-clk was removed in commit
5b8e76c35e ("powerpc, 8xx: remove support for 8xx")
allthought CONFIG_SYS_FSL_CLK is defined in
arch/arm/cpu/armv8/fsl-layerscape/Kconfig and still in use
in the following configs:

./include/configs/mx53loco.h:21:#define CONFIG_SYS_FSL_CLK
./include/configs/m53evk.h:16:#define CONFIG_SYS_FSL_CLK
./include/configs/mx25pdk.h:17:#define CONFIG_SYS_FSL_CLK
./include/configs/usbarmory.h:14:#define CONFIG_SYS_FSL_CLK
./include/configs/ls1021aqds.h:14:#define CONFIG_SYS_FSL_CLK
./include/configs/mx53cx9020.h:22:#define CONFIG_SYS_FSL_CLK
./include/configs/colibri_vf.h:17:#define CONFIG_SYS_FSL_CLK
./include/configs/mx35pdk.h:21:#define CONFIG_SYS_FSL_CLK
./include/configs/woodburn_common.h:19:#define CONFIG_SYS_FSL_CLK
./include/configs/mx7_common.h:25:#define CONFIG_SYS_FSL_CLK
./include/configs/ls1021aiot.h:12:#define CONFIG_SYS_FSL_CLK
./include/configs/ls1021atwr.h:14:#define CONFIG_SYS_FSL_CLK
./include/configs/mx53ard.h:21:#define CONFIG_SYS_FSL_CLK
./include/configs/mx53smd.h:21:#define CONFIG_SYS_FSL_CLK
./include/configs/mx51evk.h:16:#define CONFIG_SYS_FSL_CLK
./include/configs/mx6_common.h:31:#define CONFIG_SYS_FSL_CLK
./include/configs/vf610twr.h:14:#define CONFIG_SYS_FSL_CLK
./include/configs/mx53evk.h:21:#define CONFIG_SYS_FSL_CLK

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-06-29 21:30:16 -04:00
Philipp Tomsich
f8714372ed MAINTAINERS, git-mailrc: update the maintainer for rockchip
Adding myself to MAINTAINERS and git-mailrc for the rockchip
sub-architecture.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-06-23 10:38:09 -04:00
Heiko Schocher
064b55cfcb powerpc, 5xxx, 512x: remove support for mpc5xxx and mpc512x
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.

Signed-off-by: Heiko Schocher <hs@denx.de>
2017-06-16 10:14:55 -04:00
Tom Rini
4f58002013 Merge git://git.denx.de/u-boot-mpc85xx 2017-06-14 18:53:03 -04:00
York Sun
3913191c8a powerpc: mpc8540ads: mpc8560ads: Drop support for MPC8540/60ADS
Drop support for these two legacy boards.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-06-12 11:30:00 -07:00
Heiko Schocher
5025897774 powerpc, 5xx: remove support for 5xx
There was for long time no activity in the 5xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 5xx,
so remove it.

Signed-off-by: Heiko Schocher <hs@denx.de>
2017-06-12 08:38:05 -04:00
Heiko Schocher
2eb48ff7a2 powerpc, 8260: remove support for mpc8260
There was for long time no activity in the 8260 area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8260,
so remove it.

Signed-off-by: Heiko Schocher <hs@denx.de>
2017-06-12 08:38:02 -04:00
Heiko Schocher
5b8e76c35e powerpc, 8xx: remove support for 8xx
There was for long time no activity in the 8xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8xx,
so remove it (with a heavy heart, knowing that I remove
here the root of U-Boot).

Signed-off-by: Heiko Schocher <hs@denx.de>
2017-06-12 08:37:55 -04:00
Simon Glass
fe67eaccd0 README: Add instructions for chain-loading U-Boot on jerry
Add instructions for chromebook_jerry.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-09 13:45:34 -06:00
Simon Glass
ed54b1918e rockchip: jerry: Add a .its file for chromium
Add a sample .its file for booting U-Boot on a jerry Chromebook.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-09 13:45:33 -06:00
Simon Glass
c9af6673e8 README: Add instructions for chain-loading U-Boot
Most Chromebooks support chain-loading U-Boot but instructions are
somewhat scattered. Add a README to hold this information within the
U-Boot tree. Also add the standard developer keys to simplify the
instructions, since they are small.

For now this only supports nyan-big.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-09 13:39:34 -06:00
Simon Glass
13bdce8f8c tegra: nyan-big: Add a .its file for chromium
Add a sample .its file for booting U-Boot on a nyan-big Chromebook.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-09 13:39:34 -06:00
Kever Yang
4f3dc8806e MAINTAINERS: git-mailrc: update maintainer for Rockchip
Send patch to Kever Yang instead of Lin Huang for Rockchip patches,
for Lin is not always working on upstream U-Boot.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Changed , to : in subject:
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-07 07:29:22 -06:00
Bin Meng
f8f291b096 x86: baytrail: Change lpe/lpss-sio/scc FSP properties to integer
At present lpe/lpss-sio/scc FSP properties are all boolean, but in
fact for "enable-lpe" it has 3 possible options. This adds macros
for these options and change the property from a boolean type to
an integer type, and change their names to explicitly indicate what
the property is really for.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-06-05 08:55:22 +08:00
Bin Meng
5e74e5a682 x86: baytrail: Use macros instead of magic numbers for FSP settings
Introduce various meaningful macros for FSP settings and switch over
to use them instead of magic numbers.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-06-05 08:55:22 +08:00
Bin Meng
6702488cfa x86: baytrail: Remove "serial-debug-port-*" settings
"serial-debug-port-address" and "serial-debug-port-type" settings
are actually reserved in the FSP UPD data structure. Remove them.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-06-05 08:55:22 +08:00
Philipp Tomsich
de59d10cd0 doc: document u-boot, mmc-env-offset and u-boot, mmc-env-offset-redund
Adding documentation on the new config properties:
       'u-boot,mmc-env-offset' - overrides CONFIG_ENV_OFFSET
       'u-boot,mmc-env-offset-redundant'
                               - overrides CONFIG_ENV_OFFSET_REDUND

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-05-29 17:28:52 +09:00
Tom Rini
711391131c Merge git://git.denx.de/u-boot-sunxi
trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't
get Kconfig errors on platforms without SPL, ie sandbox (without SPL).

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 19:20:28 +00:00
Simon Glass
59e12a4a8c fs: Kconfig: Add a separate option for FS_JFFS2
Rather than using CMD_JFFS2 for both the filesystem and its command, we
should have a separate option for each. This allows us to enable JFFS2
support without the command, if desired, which reduces U-Boot's size
slightly.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:45:31 -04:00
Andre Przywara
411cf32d20 SPL: FIT: allow loading multiple images
So far we were not using the FIT image format to its full potential:
The SPL FIT loader was just loading the first image from the /images
node plus one of the listed DTBs.
Now with the refactored loader code it's easy to load an arbitrary
number of images in addition to the two mentioned above.
As described in the FIT image source file format description, iterate
over all images listed at the "loadables" property in the configuration
node and load every image at its desired location.
This allows to load any kind of images:
- firmware images to execute before U-Boot proper (for instance
  ARM Trusted Firmware (ATF))
- firmware images for management processors (SCP, arisc, ...)
- firmware images for devices like WiFi controllers
- bit files for FPGAs
- additional configuration data
- kernels and/or ramdisks
The actual usage of this feature would be platform and/or board specific.

Also update the FIT documentation to mention the new SPL feature and
provide an example .its file to demonstrate its features.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lokesh Vutla <lokeshvuta@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-05-17 23:15:43 +05:30
Bin Meng
13c9d84825 x86: Document ACPI S3 support
Now that we have ACPI S3 support on Intel MinnowMax board, document
some generic information of S3 and how to test it.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Stefan Roese <sr@denx.de>
2017-05-17 17:11:46 +08:00
Tom Rini
d87f82967f omap5: Migrate CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC to Kconfig
While in theory this value could be used in places outside of "omap5"
(such as OMAP4), we only make use of it today in OMAP5, so place the
Kconfig entry there.  Given that Kconfig lets us provide a default, we
drop CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC entirely.  The contents of
doc/README.omap-reset-time make a good help entry, so adjust them
slightly and delete the file.  Move the comment about range to where we
use the value now, and have Kconfig enforce the upper bound.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:39:57 -04:00
Philipp Tomsich
f222b36751 doc: document /config/u-boot, spl-payload-offset property
This adds documentation on the u-boot,spl-payload-offset property
(which overrides CONFIG_SYS_SPI_U_BOOT_OFFS during the SPI loading in
the SPL stage, if present).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-05-11 22:03:40 -04:00
Tom Rini
1f5541c881 Merge git://git.denx.de/u-boot-rockchip
This adds a new firefly-rk3399 board, MIPI support for rk3399 and
rk3288, rk818 pmic support, mkimage improvements for rockchip and a few
other things.
2017-05-10 17:40:11 -04:00
Tom Rini
102d86552a Merge branch 'master' of git://git.denx.de/u-boot-mips 2017-05-10 15:50:21 -04:00
Kever Yang
1df7ee573e doc: dtbinding: add pwm binding file
This is a copy from kernel.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Álvaro Fernández Rojas
632889cfe5 dm: led: add BCM6358 led driver
This driver is a simplified version of linux/drivers/leds/leds-bcm6358.c

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Álvaro Fernández Rojas
28300dc526 dm: led: add BCM6328 led driver
This driver is a simplified version of linux/drivers/leds/leds-bcm6328.c,
simplified to remove HW leds and blink fallbacks.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-10 16:16:09 +02:00
Alex Deymo
82f766d1d2 Allow boards to initialize the DT at runtime.
In some boards like the Raspberry Pi the initial bootloader will pass
a DT to the kernel. When using U-Boot as such kernel, the board code in
U-Boot should be able to provide U-Boot with this, already assembled
device tree blob.

This patch introduces a new config option CONFIG_OF_BOARD to use instead
of CONFIG_OF_EMBED or CONFIG_OF_SEPARATE which will initialize the DT
from a board-specific funtion instead of bundling one with U-Boot or as
a separated file. This allows boards like the Raspberry Pi to reuse the
device tree passed from the bootcode.bin and start.elf firmware
files, including the run-time selected device tree overlays.

Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-09 20:35:06 -04:00
Vikas Manocha
fd198ee1a8 ARM: DT: stm32f7: add sdram pin contol node
Also added DT binding doc for stm32 fmc(flexible memory controller).

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
2017-05-08 11:39:03 -04:00
Tom Rini
3fea953698 Merge branch 'master' of git://git.denx.de/u-boot-video 2017-04-14 22:05:17 -04:00
Songjun Wu
e6a419c5f7 at91: video: DT binding for HLCDC driver
DT binding documentation for atmel HLCDC driver.

Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
2017-04-14 15:42:42 +02:00
Tom Rini
c1a16c3ab5 Merge branch 'master' of git://git.denx.de/u-boot-socfpga 2017-04-14 09:05:57 -04:00
Stephen Arnold
8baa17832f ARM: socfpga: add fpga build and bsp handoff instructions to readme
This patch adds the steps to manually (re)build a Quartus FPGA project,
generate the required BSP glue, and update u-boot handoff files for
mainline SPL support. Requires Quartus toolchain and current U-Boot.

Signed-off-by: Steve Arnold <stephen.arnold42@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
2017-04-14 14:06:38 +02:00
Tom Rini
1622559066 Merge branch 'master' of git://www.denx.de/git/u-boot-imx
Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-13 11:19:00 -04:00
Simon Glass
f1683aa73c board_f: Rename initdram() to dram_init()
This allows us to use the same DRAM init function on all archs. Add a
dummy function for arc, which does not use DRAM init here.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Dummy function on nios2]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-13 09:40:57 -04:00
Madan Srinivas
4fce6554dc doc: Updates info on using Keystone2 secure devices
Add a section describing the secure boot image used on
Keystone2 secure devices.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-04-08 21:35:06 -04:00
Marek Vasut
fcea480d1d ARM: mxs: Rename M28EVK
The board is now manufactured by Aries Embedded GmbH , rename it.

Signed-off-by: Marek Vasut <marex@denx.de>
2017-04-05 18:12:04 +02:00
Jernej Skrabec
7da8680b26 rockchip: Add support for MiQi rk3288 board
MiQi is rk3288 based development board with 1 or 2 GB SDRAM, 16 GB eMMC,
micro SD card interface, 4 USB 2.0 ports, HDMI, gigabit Ethernet and
expansion ports.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Jernej Skrabec
43b5c78d8d rockchip: cosmetic: Sort RK3288 boards
Sort rk3288 boards in alphabetical order.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Philipp Tomsich
d02d11f8ae rockchip: rk3399: spl: make SPL boot-order configurable via /chosen
The RK3399 does not have any boot selection pins and the BootROM probes
the boot interfaces using the following boot-order:
    1. SPI
    2. eMMC (sdhci in DTS)
    3. SD card (sdmmc in DTS)
    4. USB loader
For ease of deployment, the SPL stage should mirror the boot order of
the ROM and use the same probing order (assuming that valid images can
be detected by SPL) unless instructed otherwise.  The boot-order can
then be configured via the 'u-boot,spl-boot-order' property in the
chosen-node of the DTS.

While this approach is easily extensible to other boards, it is only
implemented for the RK3399 for now, as the large SRAM on the RK3399
makes this easy to fit the needed infrastructure into SPL and our
production setup already runs with DM, OF_CONTROL and BLK in SPL.

The new boot-order property is expected to be used in conjunction with
FIT images (and all legacy image formats disabled via Kconfig).

A boot-sequence with probing and fallthroughs from SPI via eMMC to SD
card (i.e. &spiflash, &sdhci, &sdmmc) has been validated on the RK3399-Q7.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:01:57 -06:00
Heiko Stübner
f46b859bfb rockchip: rk3188: add README.rockchip paragraph describing sd boot
Building sd images for rk3188 requires more steps due to the needed split
into TPL and SPL as loaders. Describe how to build an image for it in a
separate paragraph in the READER.rockchip file.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2017-04-04 20:01:57 -06:00
Hannes Schmelzer
db40c1aa1c drivers/net/phy: add fixed-phy / fixed-link support
This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).

For this purpose we introduce a new phy-driver, called "Fixed PHY".

Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.

Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).

During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2017-03-26 09:58:26 -05:00
Tom Rini
5cf618ee60 Merge git://git.denx.de/u-boot-arc
This replaces legacy arch/arc/lib/timer.c implementation and allows us
to describe ARC Timers in Device Tree. Among other things that way we
may properly inherit Timer's clock from CPU's clock s they really run
synchronously.
2017-03-24 08:19:30 -04:00
Vlad Zakharov
ad9b5f77df drivers: timer: Introduce ARC timer driver
This commit introduces timer driver for ARC.

ARC timers are configured via ARC AUX registers so we use special
functions to access timer control registers.

This driver allows utilization of either timer0 or timer1
depending on which one is available in real hardware. Essentially
only existing timers should be mentioned in board's Device Tree
description.

Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-24 14:20:55 +03:00
mario.six@gdsys.cc
2a792753d6 dm: Add callback to modify the device tree
Certain boards come in different variations by way of utilizing daughter
boards, for example. These boards might contain additional chips, which
are added to the main board's busses, e.g. I2C.

The device tree support for such boards would either, quite naturally,
employ the overlay mechanism to add such chips to the tree, or would use
one large default device tree, and delete the devices that are actually
not present.

Regardless of approach, even on the U-Boot level, a modification of the
device tree is a prerequisite to have such modular families of boards
supported properly.

Therefore, we add an option to make the U-Boot device tree (the actual
copy later used by the driver model) writeable, and add a callback
method that allows boards to modify the device tree at an early stage,
at which, hopefully, also the application of device tree overlays will
be possible.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-03-23 15:46:23 +01:00
Konstantin Porotchkin
81192b7966 mvebu: usb: xhci: Add VBUS regulator supply to the host driver
The USB device should linked to VBUS regulator through "vbus-supply"
DTS property.
This patch adds handling for "vbus-supply" property inside the USB
device entry for turning on the VBUS regulator upon the host adapter probe.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-03-23 08:45:25 +01:00
Konstantin Porotchkin
130b53ec79 mvebu: pcie: Add support for GPIO reset for PCIe device
Add support for "marvell,reset-gpio" property to mvebu DW PCIe
driver.
This option is valid when CONFIG_DM_GPIO=y

Change-Id: Ic17c500449050c2fbb700731f1a9ca8b83298986
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-03-23 08:45:25 +01:00
Philipp Tomsich
e7dd02e377 part_efi: document device-tree binding for part_efi configuration
This adds documentation on the u-boot,efi-partition-entries-offset
property (which overrides CONFIG_EFI_PARTITION_ENTRIES_OFF, if
present).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-20 18:04:40 -04:00
Philipp Tomsich
399f3afa37 doc: move documentation for /config node into a separate file
This moves the description of the /config node from README.fdt-control
into a separate file doc/device-tree-bindings/config.txt.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-20 18:04:35 -04:00
Tom Rini
f9515756b6 Merge git://git.denx.de/u-boot-rockchip
This includes support for rk3188 from Heiko Stübner and and rk3328 from
Kever Yang.  Also included is SPL support for rk3399 and a fix for
rk3288 to get it booting again (spl_early_init()).
2017-03-17 14:15:17 -04:00
Vikas Manocha
94d5308412 PINCTRL: stm32f7: add pin control driver
This driver uses the same pin control binding as that of linux, binding
document of this patch is copied from linux. One addition done is for
GPIO input and output mode configuration which was missing.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-17 14:15:14 -04:00
Vikas Manocha
712f99a5dd clk: stm32f7: add clock driver for stm32f7 family
add basic clock driver support for stm32f7 to enable clocks required by
the peripherals.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-17 14:15:12 -04:00
Kever Yang
fa437430ad rockchip: arm64: rk3399: add ddr controller driver
RK3399 support DDR3, LPDDR3, DDR4 sdram, this patch is porting from
coreboot, support 4GB lpddr3 in this version.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Added rockchip: tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-03-16 16:03:45 -06:00
Heiko Stübner
27326c7ee2 dm: allow limiting pre-reloc markings to spl or tpl
Right now the u-boot,dm-pre-reloc flag will make each marked node
always appear in both spl and tpl. But systems needing an additional
tpl might have special constraints for each, like the spl needing to
be very tiny.

So introduce two additional flags to mark nodes for only spl or tpl
environments and introduce a function dm_fdt_pre_reloc to automate
the necessary checks in code instances checking for pre-relocation
flags.

The behaviour of the original flag stays untouched and still marks
a node for both spl and tpl.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
2017-03-16 16:03:44 -06:00
Masahiro Yamada
cf3175bcd8 ARM: uniphier: update README.uniphier for latest build instruction
Since commit c0efc3140e ("ARM: uniphier: change CONFIG_SPL_PAD_TO
to 128KB"), the u-boot.bin should be burned at the offset 0x20000.
I missed to update README.uniphier in that commit.  Now updating.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-23 08:37:56 +09:00
Eddie Cai
6f27976455 rockchip: rename miniarm to tinker board
Miniarm is the internal project code. Now it is officially named Tinker board.
So rename it.

Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-02-09 12:10:59 -07:00
Simon Glass
e160f7d430 dm: core: Replace of_offset with accessor
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-02-08 06:12:14 -07:00
Tom Rini
43ade93bdb Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2017-02-01 16:34:25 -05:00
Tom Rini
f77309d343 Merge git://www.denx.de/git/u-boot-marvell 2017-02-01 06:57:35 -05:00
Mario Six
a1b6b0a9c1 arm: mvebu: Implement secure boot
The patch implements secure booting for the mvebu architecture.

This includes:
- The addition of secure headers and all needed signatures and keys in
  mkimage
- Commands capable of writing the board's efuses to both write the
  needed cryptographic data and enable the secure booting mechanism
- The creation of convenience text files containing the necessary
  commands to write the efuses

The KAK and CSK keys are expected to reside in the files kwb_kak.key and
kwb_csk.key (OpenSSL 2048 bit private keys) in the top-level directory.

Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-02-01 09:04:18 +01:00
Masahiro Yamada
54925327fa mmc: move CONFIG_GENERIC_MMC to Kconfig
Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.

Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig.  Almost all
of the defines will go away.

I see only two exceptions:
  configs/blanche_defconfig
  configs/sandbox_noblk_defconfig

They define CONFIG_GENERIC_MMC, but not CONFIG_MMC.  Something
might be wrong with these two boards, so should be checked later.

Anyway, this is the output of the moveconfig tool.

This commit was created as follows:

[1] create a config entry in drivers/mmc/Kconfig

[2] tools/moveconfig.py -r HEAD GENERIC_MMC

[3] manual clean-up of garbage comments in doc/README.* and
    include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-31 21:50:47 +09:00
Michael Kurz
b1a8de7e07 ARM: DTS: stm32: add stm32f746-disco device tree files
This patch adds the DTS source files needed for stm32f746-disco board
The files are based on the stm32f429/469 files from current linux
kernel.

Source for "arch/arm/dts/armv7-m.dtsi": Linux: "arch/arm/boot/dts/armv7-m.dtsi"

Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
2017-01-28 14:04:42 -05:00
Fabio Estevam
7a037cc91f README: mxc_hab: Adapt the CONFIG_SECURE_BOOT text to Kconfig
Commit 6e1f4d2652 ("arm: imx-common: add SECURE_BOOT option to
Kconfig") moved the CONFIG_SECURE_BOOT option to Kconfig, so update
the mxc_hab README file to reflect that.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Gary Bisson <gary.bisson@boundarydevices.com>
2017-01-27 10:34:14 +01:00
Masahiro Yamada
2c2ab3d495 ARM: uniphier: add PXs3 SoC support
Initial support for PXs3 SoC.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-22 16:49:34 +09:00
Uri Mashiach
79267edd10 status_led: Kconfig migration - introduction
Move all of the status LED feature to drivers/led/Kconfig.
doc/README.LED updated to reflect the Kconfig implementation.

Tested boards: CL-SOM-AM57x, CM-T335

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
2017-01-21 15:12:33 -05:00
Tom Rini
f253f2933b Merge branch 'master' of git://git.denx.de/u-boot-video 2017-01-16 20:23:14 -05:00
George McCollister
f1ca1fdebf mkimage: Add support for signing with pkcs11
Add support for signing with the pkcs11 engine. This allows FIT images
to be signed with keys securely stored on a smartcard, hardware security
module, etc without exposing the keys.

Support for other engines can be added in the future by modifying
rsa_engine_get_pub_key() and rsa_engine_get_priv_key() to construct
correct key_id strings.

Signed-off-by: George McCollister <george.mccollister@gmail.com>
2017-01-14 16:47:13 -05:00
tomas.melin@vaisala.com
db1b79b886 splash: add support for loading splash from a FIT image
Enable support for loading a splash image from within a FIT image.
The image is assumed to be generated with mkimage -E flag to hold
the data external to the FIT.

Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2017-01-13 17:40:38 +01:00
Sjoerd Simons
35a05761a1 rockchip: Drop Ethernet from the TODO
Now that ethernet support works, it can be dropped from the rockchip
TODO

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-11 20:24:19 -07:00
Masahiro Yamada
ae4c81e942 mmc: move DesignWare-based drivers to Kconfig
Move (and rename) the following CONFIG options to Kconfig:

  CONFIG_EXYNOS_DWMMC  (renamed to CONFIG_MMC_DW_EXYNOS)
  CONFIG_HIKEY_DWMMC   (renamed to CONFIG_MMC_DW_K3)
  CONFIG_SOCFPGA_DWMMC (renamed to CONFIG_MMC_DW_SOCFPGA)

The "HIKEY" is a board name, so it is not suitable for the MMC
controller name.  I am following the name used in Linux.

This commit was generated as follows:

[1] Rename the config options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_EXYNOS_DWMMC/CONFIG_MMC_DW_EXYNOS/g
s/CONFIG_HIKEY_DWMMC/CONFIG_MMC_DW_K3/g
s/CONFIG_SOCFPGA_DWMMC/CONFIG_MMC_DW_SOCFPGA/g
'

[2] Commit the changes

[3] Create the entries in drivers/mmc/Kconfig
    (with default y for EXYNOS and SOCFPGA)

[4] Run the following:
tools/moveconfig.py -y -r HEAD MMC_DW_EXYNOS MMC_DW_K3 MMC_DW_SOCFPGA

[5] Sort and align drivers/mmc/Makefile for readability

[6] Clean-up doc/README.socfpga by hand

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2017-01-11 19:40:15 +09:00
Masahiro Yamada
55ed3b4698 mmc: move CONFIG_DWMMC to Kconfig, renaming to CONFIG_MMC_DW
This commit was created as follows:

[1] Rename the option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_DWMMC/CONFIG_MMC_DW/g'

[2] create the entry for MMC_DW in drivers/mmc/Kconfig
    (the prompt and help were copied from Linux)

[3] run "tools/moveconfig.py -y MMC_DW"

[4] add "depends on MMC_DW" to the MMC_DW_ROCKCHIP entry

[5] Clean-up doc/README.socfpga by hand

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2017-01-11 19:40:14 +09:00
Masahiro Yamada
b1b1add38c ARM: socfpga: remove unused CONFIG option and cleanup README.socfpga
CONFIG_SOCFPGA_DWMMC_FIFO_DEPTH is defined in the socfpga_common.h,
but not referenced at all.  Remove.

Also, clean-up the README.socfpga.  CONFIG_MMC should not be defined
in the header since it was moved to Kconfig by commit c27269953b
("mmc: complete unfinished move of CONFIG_MMC").  I see no grep hit
for the others.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2017-01-11 19:40:14 +09:00
Tom Rini
516457013e Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2017-01-02 16:32:05 -05:00
Robert P. J. Day
66723eda4e doc/README.cfi: Update code snippet, and add example.
First, update the code snippet referenced in the README file. And
since there are only two boards that override flash_cmd_reset(),
might as well show them both.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2017-01-02 11:14:01 -05:00
Sven Ebenfeld
1f6a664802 Makefile: preserve output for images that can contain HAB Blocks
To being able to sign created binaries, we need to know the HAB Blocks
for that image. Especially for the imximage type the HAB Blocks are
only available during creation of the image. We want to preserve the
information until we get to sign the files.
In the verbose case we still get them printed out instead of writing
to log files.

Cc: sbabic@denx.de

v2-Changes:
 - No usage of MKIMAGEOUTPUT_$(@F) macro.
 - Predefine default value /dev/null in every involved Makefile.

Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
2017-01-02 17:07:39 +01:00
Sven Ebenfeld
3de6c7fc00 doc: imx6: add section for secure boot with SPL
Cc: sbabic@denx.de

Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
2017-01-02 17:07:21 +01:00
Jaehoon Chung
6e1cfb099a MAINTAINERS, git-mailrc: update the Power maintainer
Przemyslaw didn't maintain the PMIC anymore.
Update the pmic maintainer from Przeymyslaw to me.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-12-27 11:24:15 -05:00
Vignesh R
bd2e9714c8 regulator: fixed: Add support to handle enable-active-high DT property
Add support to handle enable-active-high DT property. This property is
used to drive the gpio controlling fixed regulator as active high when
claiming gpio line.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-12-27 08:22:57 -05:00
Konstantin Porotchkin
0d92f2141a arm64: mvebu: Fix A8K memory mapping and add documentation
Fix the MMU mapping for A8K device family:
 - Separate A7K and A8K memory mappings
 - Fix memory regions by including IO mapping for all
   3 PCIe interfaces existing on each connected CP110 controller
Add A8K memory mapping documentation with all regions
configured by Marvell ATF.

Change-Id: I9c930569b1853900f5fba2d5db319b092cc7a2a6
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
2016-12-21 09:52:35 +01:00
Konstantin Porotchkin
f99386c5b1 arm64: mvebu: Add pin control nodes to A8K family DTS files
Add pin control nodes to APN806, CP-master, CP-slave and
Armada-7040 and Armada-8040 boards DTS files

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-12-12 09:04:52 +01:00
Konstantin Porotchkin
656e6cc86b arm64: mvebu: pinctrl: Add pin control driver for A8K family
Add a DM port of Marvell pin control driver.
The A8K SoC family contains several silicone dies interconnected
in a single package. Every die is normally equipped with its own
pin controller unit.
There are 2 pin controllers in A70x0 SoC and 3 in A80x0 SoC.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-12-12 09:04:52 +01:00
Konstantin Porotchkin
fa61ef6b49 arm64: mvebu: Add bubt command for flash image burn
Add support for mvebu bubt command for flash image
load, check and burn on boot device.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-12-12 09:04:52 +01:00
Dinh Nguyen
6fa0d34572 MAINTAINERS: socfpga: update email address for Dinh Nguyen
With the acquisition of Altera by Intel, my Altera email may be going
away soon. Update the contact to a more reliable address.

Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
2016-12-06 01:45:58 +01:00
Simon Glass
6ccb410124 dm: Add timeline and guide for porting I2C drivers
Add a README with a brief guide to porting i2c drivers over to use driver
model.

Add a timeline also. All I2C drivers should be converted by the end
of June 2017.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
2016-12-05 13:28:12 +01:00
Tom Rini
194eded14c Merge git://git.denx.de/u-boot-mpc85xx 2016-12-04 13:55:15 -05:00
Simon Glass
ebb2c53585 serial: Drop the s3c24x0 serial driver
This is not used by any boards. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-04 13:55:00 -05:00
Simon Glass
8ff89f8db8 serial: Update docs to indicate mcfuart supports DM_SERIAL
This driver was converted so we should remove it from the list.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-12-04 13:54:59 -05:00
Andrew F. Davis
d7be50921e image: Add FIT image loadable section custom processing
To help automate the loading of custom image types we add the ability
to define custom handlers for the loadable section types. When we find
a compatible type while loading a "loadable" image from a FIT image we
run its associated handlers to perform any additional steps needed for
loading this image.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-12-03 13:21:19 -05:00
York Sun
830fc1bfe7 powerpc: mpc85xx: Convert CONFIG_SYS_CCSRBAR_DEFAULT to Kconfig option
Move default value definitions to to Kconfig SYS_CCSRBAR_DEFAULT.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-12-02 08:52:34 -08:00
Tom Rini
6b29a395b6 Merge git://git.denx.de/u-boot-mpc85xx 2016-11-29 19:42:48 -05:00
Fabian Vogt
165316e38f serial: pl01x: expose skip_init platdata option in DT
To be able to represent the skip-init platdata element with OF_CONTROL,
it needs to be read from the device tree as well and put into the platform data.

Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-11-28 20:09:47 -05:00
Fabian Vogt
9f755f5d09 serial: bcm283x_mu: add device tree support
This patch adds device tree support for the bcm283x mini-uart driver.

Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-11-28 20:09:46 -05:00
Fabian Vogt
4faf5f93c6 gpio: bcm2835: add device tree support
This patch adds device tree support for the bcm2835 GPIO driver.

Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-11-28 20:09:45 -05:00
York Sun
789460c914 powerpc: P2010: Drop configuration for P2010
P2010 is a single-core version of P2020. There is no P2010 target
configured. Drop related macros. P2010 SoC is still supported.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-11-23 23:42:10 -08:00
York Sun
46d9fc0bb7 powerpc: P1014: Drop configuration for P1014
P1014 is a variant of P1010. There is no P1014 target configured.
Drop related macros. P1014 SoC is still supported.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-11-23 23:42:08 -08:00
York Sun
2f8b81268a powerpc: P1013: Drop configuration for P1013
P1013 is a single-core version of P1022. There is no P1022 target
configured. Drop related macros. P1022 SoC is still supported.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-11-23 23:42:08 -08:00
York Sun
83b9bea116 powerpc: P1012: Drop configuration for P1012
P1012 is a single-core version of P1021. There is no P1012 target
configured. Drop related macros. P1012 SoC is still supported.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-11-23 23:42:07 -08:00
York Sun
87499e938d powerpc: MPC8560ADS: Remove macro CONFIG_MPC8560ADS
This macro is no longer used.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-11-23 23:42:05 -08:00
York Sun
1ac8e0709e powerpc: MPC8540ADS: Remove macro CONFIG_MPC8540ADS
This macro is no longer used.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-11-23 23:42:05 -08:00
York Sun
7f825218dc powerpc: mpc8540: Remove macro CONFIG_MPC8540
Replace CONFIG_MPC8540 with ARCH_MPC8540 in Kconfig and clean up existing
macros.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-11-23 23:42:04 -08:00
Jagan Teki
543bd27353 MAINTAINERS: SUNXI: Update maintainership
Add Jagan and Maxime as Maintainers for SUNXI

Signed-off-by: Jagan Teki <jagan@openedev.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2016-11-22 09:07:26 -05:00
Jagan Teki
6645fd2c18 sf: Rename sf_params.c to spi_flash_ids.c
Now the flash params table as renamed to spi_flash_ids structure,
so rename the sf_params.c to spi_flash_ids.c and remove the legacy.

Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
2016-11-18 13:04:54 +05:30
Simon Glass
58ad86288f x86: Enable EFI loader support
Enable this so that EFI applications (notably grub) can be run under U-Boot
on x86 platforms.

At present the 'hello world' EFI application is not supported for the
qemu-x86_efi_payload64 board. That board builds a payload consisting of a
64-bit header and a 32-bit U-Boot, which is incompatible with the way the
EFI loader builds its EFI application. The following error is obtained:

x86_64-linux-ld.bfd: i386 architecture of input file
   `lib/efi_loader/helloworld.o' is incompatible with i386:x86-64 output

This could be corrected with additional Makefile rules. For now, this
feature is disabled for that board.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[agraf: drop hello kconfig bits]
Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14 23:24:04 +01:00
Simon Glass
c7ae3dfdcc efi: Add support for a hello world test program
It is useful to have a basic sanity check for EFI loader support. Add a
'bootefi hello' command which loads HelloWord.efi and runs it under U-Boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
[agraf: Fix documentation, add unfulfilled kconfig dep]
Signed-off-by: Alexander Graf <agraf@suse.de>
2016-11-14 23:24:03 +01:00
Tom Rini
d8c4eb60f8 Merge branch 'master' of git://git.denx.de/u-boot-net 2016-11-07 13:16:00 -05:00
Stephen Warren
afb970f78a dt: net: add DWC EQoS binding
The Synopsys DWC EQoS is a configurable Ethernet MAC/DMA IP block which
supports multiple options for bus type, clocking and reset structure, and
feature list.

This patch imports the binding from the Linux kernel, including my V3
patch to extend the binding to cover the Tegra186, which is applied for
next-20160912. So far, my changes have been acked by Lars Persson, the
original author of the binding.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-11-07 11:28:15 -06:00
Tomeu Vizoso
0f7c6cdc81 mkimage: Allow including a ramdisk in FIT auto mode
Adds -i option that allows specifying a ramdisk file to be added to the
FIT image when we are using the automatic FIT mode (no ITS file).

This makes adding Depthcharge support to LAVA much more convenient, as
no additional configuration files need to be kept around in the machine
that dispatches jobs to the boards.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Matt Hart <matthew.hart@linaro.org>
Cc: Neil Williams <codehelp@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-11-06 07:33:42 -05:00
Andre Przywara
8add67911d doc: update README.arm64
This file apparently hasn't seen an update in a while, so just sync
it with reality.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2016-11-05 07:27:44 -04:00
Jacob Chen
3f3e1e3395 rockchip: doc: add GPT partition layout
A simple introduction.

Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-10-30 13:29:06 -06:00
Jagan Teki
16185a85d9 MAINTAINERS: Update Jagan's email
Signed-off-by: Jagan Teki <jagan@openedev.com>
2016-10-29 09:00:01 -04:00
Masahiro Yamada
12a5ce7273 ARM: uniphier: update doc/README.uniphier
- Rephrase the toolchains section.  Leave only Linaro toolchains
   since it is the most tested these days.

 - Add build instruction for ARMv8 SoC boards

 - Add information about "ddrmphy" command

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-10-18 14:30:05 +09:00
Masahiro Yamada
52159d27ff ARM: dts: uniphier: sync DT with latest Linux
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-10-18 14:06:46 +09:00
Bin Meng
2d3c573ee6 x86: coreboot: Convert to use DM coreboot video driver
This converts coreboot to use DM framebuffer driver.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12 10:58:24 +08:00
Bin Meng
10491c838e x86: doc: Correct qfw command example
The kernel load address for zboot should be 0x1000000.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12 10:56:50 +08:00
Bin Meng
4dc5e54da3 x86: doc: Document coreboot framebuffer driver issue on QEMU
For some unknown reason, coreboot framebuffer driver never works on
QEMU since day 1. It seems the driver only works on real hardware.
Document this issue.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-12 10:55:38 +08:00
Tom Rini
f5fd45ff64 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-10-08 09:33:37 -04:00
Stefan Agner
c571d6828d power: pmic: add Ricoh RN5T567 PMIC support
Add device model enabled PMIC driver for Ricoh RN5T567 PMIC used
on Colibri iMX7.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-07 12:26:15 +02:00
Stefan Agner
a99546ab62 dm: imx: serial: support device tree
Support instatiation through device tree. Also parse the fsl,dte-mode
property to determine whether DTE mode shall be used.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-07 12:26:14 +02:00
Jelle van der Waa
4fd096f450 doc: typo fix addess -> address
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
2016-10-06 20:58:17 -04:00
Simon Glass
4dc34be430 README: Fix CONFIG_SYS_NAND_MAX_DEVICE typo
This should be CONFIG_SYS_MAX_NAND_DEVICE. Fix it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Scott Wood <oss@buserror.net>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06 20:40:54 -04:00
Simon Glass
b43957baf7 README: Drop CONFIG_MPC8349ADS
This option is not used now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06 20:40:51 -04:00
Simon Glass
89e5440ef7 README: Drop README.imx31
The only content of this file is CONFIG options which are no-longer present
in U-Boot. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06 20:40:49 -04:00
Simon Glass
b44b632a68 atmel: Drop README.at91-soc
This issue covered by this doc appears to be fixed, so let's remove the
README.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Acked-by: Andreas Bießmann <andreas@biessmann.org>
2016-10-06 20:40:46 -04:00
Simon Glass
b2482dffa0 README: Drop unused JFFS2 options
There appear to be neither implemented nor used. Drop them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06 20:40:26 -04:00
Fabio Estevam
112d59a18d README.imx6: Fix Boundary Devices name
Correct name is "Boundary Devices".

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-10-04 12:01:15 +02:00
Andrew F. Davis
f7160eac83 doc: Update info on using AM33xx secure devices from TI
Add a section describing the additional boot types used on AM33xx
secure devices.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-10-02 08:09:59 -04:00
Petr Kulhavy
da2ee24d91 disk: part: refactor generic name creation for DOS and ISO
In both DOS and ISO partition tables the same code to create partition name
like "hda1" was repeated.

Code moved to into a new function part_set_generic_name() in part.c and optimized.
Added recognition of MMC and SD types, name is like "mmcsda1".

Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-01 20:04:56 -04:00
Petr Kulhavy
b6dd69a4d6 fastboot: add support for writing MBR
Add special target "mbr" (otherwise configurable via CONFIG_FASTBOOT_MBR_NAME)
to write MBR partition table.
Partitions are now searched using the generic function which finds any
partiiton by name. For MBR the partition names hda1, sda1, etc. are used.

Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-01 20:04:51 -04:00
Paul Burton
ad8783cb1c boston: Introduce support for the MIPS Boston development board
This patch introduces support for building U-Boot to run on the MIPS
Boston development board. This is a board built around an FPGA & an
Intel EG20T Platform Controller Hub, used largely as part of the
development of new CPUs and their software support. It is essentially
the successor to the older MIPS Malta board.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-09-21 16:24:36 +02:00
Wenbin Song
fce78503b2 pxe: Modify README to add the description about FIT image
Use environment variable "kernel_addr_r" to indicate the location
in RAM where FIT image will be stored.
Use label command "kernel" to indicate which <path> the FIT image at.

Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
2016-09-07 08:49:03 -04:00
John Keeping
7302fbb31d regulator: fixed: obey startup delay
When enabling a fixed regulator, it may take some time to rise to the
correct voltage.  If we do not delay here then subsequent operations
will fail.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-06 13:18:21 -04:00
Masahiro Yamada
c21fc7e223 treewide: fix "followings" to "following"
Most of them are my mistakes.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-08-26 17:04:58 -04:00
Simon Glass
37b4a9098c x86: Mention running U-Boot in 64-bit mode in the README
This feature is not supported. Document this, and add some details on how it
might be implemented.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-08-16 11:44:09 +08:00
Simon Glass
007adbc2f9 x86: Add a reference to README.efi
UEFI is commonly used on x86. Add a reference to U-Boot's support for this
in the x86 README.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-08-16 11:44:09 +08:00
Simon Glass
dc396210d9 x86: Mention how to boot a 64-bit kernel from U-Boot
The README indicates that this is not supported, but this is no-longer true.
Update the text to indicate this and describe the FIT changes required.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-08-16 11:44:09 +08:00
Stefan Roese
5d98c5ec8e x86: doc: Add note about the debug FSP usage on BayTrail
The debug FSP image is bigger in size than the normal FSP image. This
patch adds a small description on how to use this FSP debug version
by changing CONFIG_FSP_ADDR.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-08-16 11:44:09 +08:00
Chris Zankel
de5e5cea02 xtensa: add support for the xtensa processor architecture [1/2]
The Xtensa processor architecture is a configurable, extensible,
and synthesizable 32-bit RISC processor core provided by Cadence.

This is the first part of the basic architecture port with changes to
common files. The 'arch/xtensa' directory, and boards and additional
drivers will be in separate commits.

Signed-off-by: Chris Zankel <chris@zankel.net>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-08-15 18:46:38 -04:00
Wenyou Yang
256a3f2466 atmel: Bring in at91 pio4 device tree file and bindings
Bring in required device tree file and bindings from Linux.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-08-15 22:58:04 +02:00
Songjun Wu
e3b7599be7 i2c: atmel: DT binding for i2c driver
DT binding documentation for atmel i2c driver.

Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2016-08-15 22:12:00 +02:00
Vignesh R
5746b0df9c gpio: Add driver for TI PCF8575 I2C GPIO expander
TI's PCF8575 is a 16-bit I2C GPIO expander.The device features a
16-bit quasi-bidirectional I/O ports. Each quasi-bidirectional I/O can
be used as an input or output without the use of a data-direction
control signal. The I/Os should be high before being used as inputs.
Read the device documentation for more details[1].

This driver is based on pcf857x driver available in Linux v4.7 kernel.
It supports basic reading and writing of gpio pins.

[1] http://www.ti.com/lit/ds/symlink/pcf8575.pdf

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-08-08 13:32:53 -04:00
Tom Rini
2863a9bfc2 Merge git://git.denx.de/u-boot-rockchip 2016-08-06 11:38:14 -04:00
Xu Ziyuan
1c62d99952 rockchip: add support for rk3288 miniarm board
Miniarm is a rockchip rk3288 based development board, which has lots of
interface such as HDMI, USB, micro-SD card, Audio etc.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-08-05 17:56:08 -06:00
Stephen Warren
6e7a11e64e dt-bindings: add Tegra186 BPMP I2C binding
In Tegra186, the BPMP (Boot and Power Management Processor) owns certain
HW devices, such as the I2C controller for the power management I2C bus.
Software running on other CPUs must perform IPC to the BPMP in order to
execute transactions on that I2C bus. This binding describes an I2C bus
that is accessed in such a fashion.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-04 13:36:59 -07:00
Stephen Warren
390ae57c76 dt-bindings: allow child nodes inside the Tegra BPMP
The BPMP implements some services which must be represented by separate
nodes. For example, it can provide access to certain I2C controllers, and
the I2C bindings represent each I2C controller as a device tree node.
Update the binding to describe how the BPMP supports this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-04 13:36:59 -07:00
Stephen Warren
7b9cb49405 ARM: tegra: add BPMP DT bindings
The Tegra BPMP (Boot and Power Management Processor) is a separate
auxiliary CPU embedded into Tegra to perform power management work, and
controls related features such as clocks, resets, power domains, PMIC I2C
bus, etc. These bindings dictate how to represent the BPMP in device tree.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-04 13:36:58 -07:00
Stephen Warren
729c2db7a9 ARM: tegra: adapt to latest HSP DT binding
The DT binding for the Tegra186 HSP module apparently wasn't quite final
when I posted initial U-Boot support for it. Add the final DT binding doc
and adapt all code and DT files to match it.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-04 13:36:58 -07:00
Jaehoon Chung
dbc39699d0 MAINTAINERS, git-mailrc: Update the mmc maintainer
Update the mmc maintainer from Pantelis to me.

Acked-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2016-08-02 07:30:56 -04:00
Simon Glass
6de80f2196 Drop references to MAKEALL in the documentation
It is confusing to mention MAKEALL when it is not the normal way of building
U-Boot anymore. Update the documentation to suit.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-31 19:37:08 -06:00
jk.kernel@gmail.com
dd63fbc70a rockchip: add support for rk3288 PopMetal board
PopMetal is a rockchip rk3288 based board made by ChipSpark, which has
many interface such as HDMI, VGA, USB, micro-SD card, WiFi, Audio and
Gigabit Ethernet.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-31 07:24:20 -06:00
jk.kernel@gmail.com
d7ca67b7cd rockchip: add basic support for fennec-rk3288 board
Fennec is a RK3288-based development board with 2 USB ports, HDMI,
micro-SD card, audio and WiFi and Gigabit Ethernet. It also includes
on-board 8GB eMMC and 2GB of SDRAM. Expansion connectors provides access
to display pins, I2C, SPI, UART and GPIOs.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-31 07:24:20 -06:00
Tom Rini
4711e7f7af Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-07-28 08:45:00 -04:00
Xu Ziyuan
a16e2e0680 rockchip: update fastboot usage
Introduce how to use fastboot feature on rk3288.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25 20:46:45 -06:00
Xu Ziyuan
744368d6ae rockchip: add basic support for evb-rk3288 board
evb-3288 board RK3288-based development board with 2 USB ports, HDMI,
VGA, micro-SD card, audio, WiFi and Gigabit Ethernet. It also includes
on-board 8G eMMC and 2GB of SDRAM. Expansion connector provide access to
display pins, I2C, SPI, UART and GPIOs. This add some basic files
required to allow the board to output serial messaged and can run
command(mmc info etc).

evb-rk3288 also supports booting from eMMC or SD card, the default is eMMC.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-25 20:44:18 -06:00
Xu Ziyuan
b47ea79219 rockchip: add option to change method of loading u-boot
If we would like to boot from SD card, we have to implement mmc driver
in SPL stage, and get a slightly large SPL binary. Rockchip SoC's
bootrom code has the ability to load spl and u-boot, then boot.

If CONFIG_ROCKCHIP_SPL_BACK_TO_BROM is enabled, the spl will return to
bootrom in board_init_f(), then bootrom loads u-boot binary.

Loading sequence after rework:
bootrom ==> spl ==> bootrom ==> u-boot

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed up spelling of U-Boot, boorom, opinion->option, Rochchip:
Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-25 20:44:18 -06:00
Thomas Gleixner
6f4e7d3c75 spl: Lightweight UBI and UBI fastmap support
Booting a payload out of NAND FLASH from the SPL is a crux today, as
it requires hard partioned FLASH. Not a brilliant idea with the
reliability of todays NAND FLASH chips.

The upstream UBI + UBI fastmap implementation which is about to
brought to u-boot is too heavy weight for SPLs as it provides way more
functionality than needed for a SPL and does not even fit into the
restricted SPL areas which are loaded from the SoC boot ROM.

So this provides a fast and lightweight implementation of UBI scanning
and UBI fastmap attach. The scan and logical to physical block mapping
code is developed from scratch, while the fastmap implementation is
lifted from the linux kernel source and stripped down to fit the SPL
needs.

The text foot print on the board which I used for development is:

6854	0	0	6854	1abd
drivers/mtd/ubispl/built-in.o

Attaching a NAND chip with 4096 physical eraseblocks (4 blocks are
reserved for the SPL) takes:

In full scan mode:      1172ms
In fastmap mode:          95ms

The code requires quite some storage. The largest and unknown part of
it is the number of fastmap blocks to read. Therefor the data
structure is not put into the BSS. The code requires a pointer to free
memory handed in which is initialized by the UBI attach code itself.

See doc/README.ubispl for further information on how to use it.

This shares the ubi-media.h and crc32 implementation of drivers/mtd/ubi
There is no way to share the fastmap code, as UBISPL only utilizes the
slightly modified functions ubi_attach_fastmap() and ubi_scan_fastmap()
from the original kernel ubi fastmap implementation.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-22 09:53:00 -04:00
Tom Rini
89ca873e2d Merge git://git.denx.de/u-boot-mpc85xx 2016-07-21 20:20:00 -04:00
Sumit Garg
ebfc066e6f doc: SPL: Add README for secure boot support
Adds information regarding SPL handling validation process of main u-boot
image on power/mpc85xx and arm/layerscape platforms.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-21 11:11:29 -07:00
Tom Rini
45031f1a1e Merge branch 'master' of git://git.denx.de/u-boot-sh 2016-07-21 10:40:35 -04:00
Robert P. J. Day
62a3b7dd08 Various, unrelated tree-wide typo fixes.
Fix a number of typos, including:

     * "compatble" -> "compatible"
     * "eanbeld" -> "enabled"
     * "envrionment" -> "environment"
     * "FTD" -> "FDT" (for "flattened device tree")
     * "ommitted" -> "omitted"
     * "overriden" -> "overridden"
     * "partiton" -> "partition"
     * "propogate" -> "propagate"
     * "resourse" -> "resource"
     * "rest in piece" -> "rest in peace"
     * "suport" -> "support"
     * "varible" -> "variable"

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2016-07-16 09:43:12 -04:00
Tom Rini
ebe621d5fb Merge git://git.denx.de/u-boot-dm 2016-07-15 08:06:22 -04:00
Simon Glass
1269625177 dm: Update the of-platdata README for the new features
Revise the content based on the v2 additions. This is kept as a separate
patch to avoid confusing those who have already reviewed the v1 series.

Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Tom Rini <trini@konsulko.com>
2016-07-14 20:40:24 -06:00
Simon Glass
39782afb1a dm: Add a README for of-platdata
Add documentation on how this works, including the benefits and drawbacks.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-14 20:40:24 -06:00
Andreas Dannenberg
8662bea38e doc: Update info on using secure devices from TI
Adds information regarding SPL handling the loading and processing of
secured u-boot images as part of the second stage boot the SPL does.
Introduces the description of a new interface script in the TI SECDEV
Package which handles the creation and prep of secured binary images.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-14 18:22:23 -04:00
Hannes Schmelzer
0750701a3f driver/net/fec: support fixed speed connection
If MAC is directly connected to another MAC (like a switch for example)
we don't need to probe for a phy, autoneogation and so on. We simply
have to setup speed.

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-07-12 17:58:48 +02:00
Bin Meng
79c2c257cf x86: acpi: Pack global NVS into ACPI table
Now that platform-specific ACPI global NVS is added, pack it into
ACPI table and get its address fixed up.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-12 13:46:01 +08:00
jk.kernel@gmail.com
5fb0001a67 git-mailrc: add rockchip alias
It's easier to Cc rockchip maintainers on rockchip-releated patches.

Signed-off-by: jk <jk.kernel@gmail.com>
2016-07-11 10:56:54 -04:00
Yoshinori Sato
747431b9d5 serial_sh: Add standrad SCI (w/o FIFO) support
Add support for standard type SCI (without FIFO) port.

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2016-07-09 05:51:57 +09:00
Yoshinori Sato
359787cfe4 serial_sh: Device Tree support
Add Device Tree bindings.

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2016-07-09 05:51:57 +09:00
Masahiro Yamada
2fbb8462b0 autoboot: remove CONFIG_ZERO_BOOTDELAY_CHECK
As the help message of CONFIG_BOOTDELAY says, CONFIG_BOOTDELAY=-2
means the autoboot with no delay, with no abort check even if
CONFIG_ZERO_BOOTDELAY_CHECK is defined.

To sum up, the autoboot behaves as follows:

 [1] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=y
    autoboot with no delay, but you can abort it by key input

 [2] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
    autoboot with no delay, with no check for abort

 [3] CONFIG_BOOTDELAY=-1
    disable autoboot

 [4] CONFIG_BOOTDELAY=-2
    autoboot with no delay, with no check for abort

As you notice, [2] and [4] come to the same result, which means we
do not need CONFIG_ZERO_BOOTDELAY_CHECK.  We can control all the
cases only by CONFIG_BOOTDELAY, like this:

 [1] CONFIG_BOOTDELAY=0
    autoboot with no delay, but you can abort it by key input

 [2] CONFIG_BOOTDELAY=-1
    disable autoboot

 [3] CONFIG_BOOTDELAY=-2
    autoboot with no delay, with no check for abort

This commit converts the logic as follow:
  CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
    --> CONFIG_BOOTDELAY=-2

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Christian Riesch <christian.riesch@omicronenergy.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2016-07-01 17:42:55 -04:00
Teddy Reed
f8f9107d97 mkimage: fit: spl: Add an optional static offset for external data
When building a FIT with external data (-E), U-Boot proper may require
absolute positioning for executing the external firmware. To acheive this
use the (-p) switch, which will replace the amended 'data-offset' with
'data-position' indicating the absolute position of external data.

It is considered an error if the requested absolute position overlaps with the
initial data required for the compact FIT.

Signed-off-by: Teddy Reed <teddy.reed@gmail.com>
2016-06-24 17:23:06 -04:00
Hans de Goede
9f823615af Kconfig: Add a new DISTRO_DEFAULTS Kconfig option
DISTRO_DEFAULTS is intended to mirror / replace
include/config_distro_defaults.h.

The intend is for boards which include this file to select this from
their Kconfig files and when moving setting to Kconfig which are #define-ed
in config_distro_defaults.h to select this from DISTRO_DEFAULTS so that
boards which have selected DISTRO_DEFAULTS will keep the same configuration
as before without needing any defconfig file changes.

The initial list of selected things matches all settings recently removed
from config_distro_defaults.h because they have been converted to Kconfig,
with the exception of CMD_ELF and CMD_NET, which have a default of y, if
the default of these ever changes they should be selected by DISTRO_DEFAULTS
too.

For testing and example purposes this commit also converts ARCH_SUNXI
to use DISTRO_DEFAULT instead of selecting everything it needs itself.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-20 21:30:13 -04:00
Tom Rini
2313d48445 Merge git://git.denx.de/u-boot-nand-flash 2016-06-20 05:15:52 -04:00
Boris Brezillon
30780f9483 mtd: nand: Patch remaining places where nand_to_mtd() should be used
Some drivers are still directly accessing the chip->mtd field. Patch
them to use nand_to_mtd() instead.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-06-19 19:28:38 -05:00
Fabian Mewes
caad0d00a8 nand: doc: fix example ecc scheme calculation
Signed-off-by: Fabian Mewes <architekt@coding4coffee.org>
2016-06-19 19:26:55 -05:00
Max Krummenacher
1866be7d28 nand: extend nand torture
nand torture currently works on exactly one nand block which is specified
by giving the byteoffset to the beginning of the block.

Extend this by allowing for a second parameter specifying the byte size
to be tested.

e.g.
==> nand torture 1000000

NAND torture: device 0 offset 0x1000000 size 0x20000 (block size 0x20000)
 Passed: 1, failed: 0

==> nand torture 1000000 40000

NAND torture: device 0 offset 0x1000000 size 0x40000 (block size 0x20000)
 Passed: 2, failed: 0

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
[scottwood: fix usage to show size as optional, and add misssing braces]
Signed-off-by: Scott Wood <oss@buserror.net>
2016-06-19 19:25:12 -05:00
Stephen Warren
89c1e2da78 Add a reset driver framework/uclass
A reset controller is a hardware module that controls reset signals that
affect other hardware modules or chips.

This patch defines a standard API that connects reset clients (i.e. the
drivers for devices affected by reset signals) to drivers for reset
controllers/providers. Initially, DT is the only supported method for
connecting the two.

The DT binding specification (reset.txt) was taken from Linux kernel
v4.5's Documentation/devicetree/bindings/reset/reset.txt.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-06-19 17:05:55 -06:00
Bin Meng
2600ba6de0 x86: Update x86-pinctrl driver device-tree-bindings doc
This updates the device-tree-bindings doc for x86-pinctrl driver:

 - clarify "gpio-offset" is required only when "mode-gpio" is set
 - correct property name "pull-strength"
 - use tab instead of space at several places

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-06-12 12:19:35 +08:00
Heiko Schocher
3e584b94d2 doc, spl, am335x: update am335x-network
on the shc board we see when booting in net boot mode,
that the ROM bootloader sends "AM335x ROM" as
vendor-class-identifier. U-Boots doc says "DM814x ROM".

So, add the info to the doc, that there is also
"AM335x ROM" possible.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-09 13:53:10 -04:00
Tom Rini
715b3a9b24 Merge git://git.denx.de/u-boot-nand-flash 2016-06-04 08:49:47 -04:00
Scott Wood
b616d9b0a7 nand: Embed mtd_info in struct nand_chip
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.

This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip.  It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].

Signed-off-by: Scott Wood <oss@buserror.net>
2016-06-03 20:27:48 -05:00
Stephen Warren
074a1fdd27 gpio: add Tegra186 GPIO driver
Tegra186's GPIO controller register layout is significantly different from
previous chips, so add a new driver for it. In fact, there are two
different GPIO controllers in Tegra186 that share a similar register
layout, but very different port mapping. This driver covers both.

The DT binding is already present in the Linux kernel (in linux-next via
the Tegra tree so far).

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org> # v1
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-05-31 09:54:24 -07:00
Tom Rini
f3c264f9de Merge branch 'master' of git://git.denx.de/u-boot-x86 2016-05-30 13:56:26 -04:00
Bin Meng
e6ddb6b013 x86: galileo: Enable ACPI table generation
Enable ACPI table generation by creating a DSDT table.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-30 10:21:12 +08:00
Tom Rini
e4a94ce4ac Merge git://git.denx.de/u-boot-dm
For odroid-c2 (arch-meson) for now disable designware eth as meson
now needs to do some harder GPIO work.

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	lib/efi_loader/efi_disk.c

Modified:
	configs/odroid-c2_defconfig
2016-05-27 20:34:12 -04:00
Daniel Allred
98350f7f37 doc: Add info on using secure devices from TI
Adds doc/README.ti-secure file to explain in generic terms
how boot images need to be created for secure devices from
Texas Instruments.

Specific details for creating secure boot images for the
AM43xx, DRA7xx and AM57xx secure devices from Texas
Instruments are also provided in the README file.

Secure devices require a security development package (SECDEV)
package that can be downloaded from:

	http://www.ti.com/mysecuresoftware

Login is required and access is granted under appropriate NDA
and export control restrictions.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:32 -04:00
Simon Glass
89b199c3d4 Remove/update old generic-board documentation and warning
Remove the warning from the Makefile, since boards that do not use generic
board will no longer build. Also update documentation.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2016-05-27 15:39:50 -04:00
Stephen Warren
6238935d01 Add a mailbox driver framework/uclass
A mailbox is a hardware mechanism for transferring small message and/or
notifications between the CPU on which U-Boot runs and some other device
such as an auxilliary CPU running firmware or a hardware module.

This patch defines a standard API that connects mailbox clients to mailbox
providers (drivers). Initially, DT is the only supported method for
connecting the two.

The DT binding specification (mailbox.txt) was taken from Linux kernel
v4.5's Documentation/devicetree/bindings/mailbox/mailbox.txt.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-05-26 20:48:31 -06:00
Stephen Warren
daac3bfee5 dm: allow setting driver_data before/during bind
This will allow a driver's bind function to use the driver data. One
example is the Tegra186 GPIO driver, which instantiates child devices
for each of its GPIO ports, yet supports two different HW instances each
with a different set of ports, and identified by the udevice_id .data
field.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-05-26 20:48:31 -06:00
Tom Rini
2ee490a024 Merge branch 'master' of git://git.denx.de/u-boot-net
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	drivers/net/zynq_gem.c
2016-05-24 11:59:02 -04:00
Dan Murphy
c7ba7bdc9d net: phy: dp83867: Add device tree bindings and documentation
Add the device tree bindings and the accompanying documentation
for the TI DP83867 Giga bit ethernet phy driver.

The original document was from:
    [commit 2a10154abcb75ad0d7b6bfea6210ac743ec60897 from the Linux kernel]

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24 11:42:04 -05:00
Tom Rini
ec8fb48ce9 Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze 2016-05-24 08:20:43 -04:00
Michal Simek
ed0cea7c52 mkimage: Report information about fpga
Add FIT_FPGA_PROP that user can identify an optional
entry for fpga.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-24 11:15:02 +02:00
Tom Rini
6d54868eeb Merge branch 'master' of git://git.denx.de/u-boot-x86 2016-05-23 18:32:47 -04:00
Bin Meng
efd4be4c82 x86: doc: Add porting hints for ACPI with Windows
Windows might cache system information and only detect ACPI changes
if you modify the ACPI table versions.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-23 15:18:00 +08:00
Bin Meng
206a3a4246 x86: doc: Mention Ubuntu/Windows installation and boot support
As of now, U-Boot can support installing and booting Ubuntu/Windows
with the help of SeaBIOS. Update the documentation.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-23 15:18:00 +08:00
Bin Meng
5a6a2c714e x86: doc: Update information about IGD with SeaBIOS
Document how to make SeaBIOS load and run the VGA ROM of Intel
IGD device when loaded by U-Boot.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-23 15:18:00 +08:00
Bin Meng
91fc5bf652 x86: minnowmax: Adjust U-Boot environment address in SPI flash
Currently U-Boot environment address is at offset 0x7fe00 of a 8MB
SPI flash. When creating a partial u-boot.rom image without flash
descriptor and ME firmware, U-Boot actually occupies the last 1MB
of the flash, and reprograming U-Boot causes previous environment
settings get lost which is not convenient during testing.

Adjust the environment address to 0x6ef000 instead (before the MRC
cache data region in the flash).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-23 15:18:00 +08:00
Bin Meng
49d929bbc4 x86: doc: Document ACPI support
Remove ACPI from the TODO list and add a new section to document
current ACPI support in U-Boot.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-23 15:18:00 +08:00
Bin Meng
eda995a8b0 x86: doc: Minor update for accuracy
This updates the doc for the following places:
- Mention CRB for Bayley Bay
- Mention Congatec QEVAL 2.0 & conga-QA3/E3845
- Limit part of the QEMU paragraphs to 80 cols
- Correct some typos (drive, it's, Ubuntu)
- Add description for "console=ttyS0,115200"
- Remove CONFIG_BOOTDELAY description which is already
  in x86-common.h

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-23 15:18:00 +08:00
Bin Meng
d4e61f505b x86: irq: Enable SCI on IRQ9
By default SCI is disabled after power on. ACTL is the register to
enable SCI and route it to PIC/APIC. To support both ACPI in PIC
mode and APIC mode, configure SCI to use IRQ9.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
2016-05-23 15:18:00 +08:00
Wills Wang
b85dc46072 drivers: spi: add spi support for QCA/Atheros ath79 SOCs
This patch add a compatible spi driver for ath79 series SOC.

Signed-off-by: Wills Wang <wills.wang@live.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-05-21 01:25:50 +02:00
Wills Wang
60b49761e9 drivers: serial: add serial driver for ar933x SOC
This patch add support for ar933x serial.

Signed-off-by: Wills Wang <wills.wang@live.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-21 01:25:50 +02:00
Robert P. J. Day
1cc0a9f496 Fix various typos, scattered over the code.
Spelling corrections for (among other things):

* environment
* override
* variable
* ftd (should be "fdt", for flattened device tree)
* embedded
* FTDI
* emulation
* controller
2016-05-05 21:39:26 -04:00
Andreas Bießmann
09c2b8f3e3 Change my mailaddress
I'll switch my mails to my own server, so drop all gmail references.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-05-02 18:37:09 -04:00
Andreas Bießmann
7a439cadcf mkimage: fix argument parsing on BSD systems
The getopt(3) optstring '-' is a GNU extension which is not available on BSD
systems like OS X.

Remove this dependency by implementing argument parsing in another way. This
will also change the lately introduced '-b' switch behaviour.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-02 18:37:09 -04:00
Tom Rini
f4c6f9335c Merge branch 'master' of git://git.denx.de/u-boot-samsung 2016-04-26 07:20:45 -04:00
Robert P. J. Day
28983f4b1a doc: Updated README.ext4
Clean up the ext4 README file.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2016-04-18 17:11:47 -04:00
Jagan Teki
e57f9c8eef doc: driver-model: Update dm tests run using test.py
Since all the tests are implemented in pytest infrastructure,
So update the dm tests with the same instead of ./test/dm/test-dm.sh

Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-04-14 11:51:39 -06:00
Shawn Guo
3af65c3f55 odroid: Update README with correct firmware link and XU4 support
The firmware from link [1] only works with U-Boot image that is no
bigger than 328KiB.  Using it with the default mainline U-Boot today
which is already around 500KiB is just not working.  Correct the link
to be hardkernel_1mb_uboot one [2], so that users can get mainline
U-Boot work out of box.

While at it, the README is updated to include XU4 support, like DTB file
name.

[1] https://github.com/hardkernel/u-boot/tree/odroidxu3-v2012.07/sd_fuse/hardkernel
[2] https://github.com/hardkernel/u-boot/tree/odroidxu3-v2012.07/sd_fuse/hardkernel_1mb_uboot

Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2016-04-14 19:38:40 +09:00
Moritz Fischer
17573c2791 i2c: Describe Cadence I2C devicetree bindings
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:07 +02:00
York Sun
3c1d218a1d armv8: LS2080A: Consolidate LS2080A and LS2085A
LS2080A is the primary SoC, and LS2085A is a personality with AIOP
and DPAA DDR. The RDB and QDS boards support both personality. By
detecting the SVR at runtime, a single image per board can support
both SoCs. It gives users flexibility to swtich SoC without the need
to reprogram the board.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2016-04-06 10:26:46 -07:00
Mateusz Kulikowski
e721e98125 Add myself as Snapdragon and SPMI maintainer
- Update MAINTAINERS
- Update git-mailrc

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:27 -04:00
Mateusz Kulikowski
120800df72 gpio: Add support for Qualcomm PM8916 gpios
This driver supports GPIOs present on PM8916 PMIC.
There are 2 device drivers inside:
- GPIO driver (4 "generic" GPIOs)
- Keypad driver that presents itself as GPIO with 2 inputs (power and reset)

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:13 -04:00
Mateusz Kulikowski
c2f74c8f53 pmic: Add support for Qualcomm PM8916 PMIC
This PMIC is connected on SPMI bus so needs SPMI support enabled.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:13 -04:00