Commit graph

2620 commits

Author SHA1 Message Date
Fabio Estevam
e100a3d52e mx25: Place common functions into sys_proto.h
imx-regs.h is meant to contain SoC register definitions.

Common SoC funtions should go to sys_proto.h instead.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-26 16:28:07 +02:00
Stefano Babic
d81b27a245 MX35: add support for woodburn board
The woodburn board is based on the MX35 SOC.
Support for both external (NOR) and internal
(SD Card) boot mode are added. It uses the
generic SPL framework to implement the internal boot
mode.

The following peripherals are supported:
- Ethernet (FEC)
- SD Card
- NAND (512 MB)
- NOR Flash

In the internal boot mode, a simple imximage header
is generated to set the address in internal RAM
where the SOC must copy the SPL code. The initial setup
is then demanded to the SPL itself.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-26 16:27:59 +02:00
Stefano Babic
a3cbc3969d ARM: Add SPL target to arm1136
The patch adds SPL for the arm1136 architecture and
inserts SPL (the produced binary) to clobber target
in the main Makefile.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-26 16:27:59 +02:00
Stefano Babic
d41924a2c1 MX35: Add soc_boot_mode and soc_boot_device to MX35
The functions are required to use the generic
SPL Framework.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-26 16:27:58 +02:00
Stefano Babic
e650030347 MX35: add LOW_LEVEL_SRAM_STACK to use SPL_FRAMEWORK
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-26 16:27:58 +02:00
Stefano Babic
b736e4b929 ARM: Fix start.S when used with SPL in arm1136
This patch modifies start.S for the arm1136 to make it
conform to start.S  in armv7 architecture, to make it
usable if the SPL framework is used.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-26 16:27:58 +02:00
Stefano Babic
01968b96a2 MX5: fix warning in clock.c
Patch fix warnings compiling with ELDK-4.2:

clock.c: In function 'get_standard_pll_sel_clk':
clock.c:341: warning: 'freq' may be used uninitialized in this function

Reported-by : Marek Vasut <marex@denx.de>
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-26 16:11:32 +02:00
Fabio Estevam
c4fe17f6d8 mx5: Add workaround for ARM erratum ID 468414
Add the software workaround for ARM erratum ID 468414.

According to mx53/mx51 errata document:

"ENGcm11133 - ARM: NEON load data can be incorrectly forwarded to a
subsequent request

Description:

Under very specific set of conditions, data from a Neon load request can be incorrectly forwarded
to a subsequent, unrelated memory request.
The conditions are as follows:
• Neon loads and stores must be in use
• Neon L1 caching must be disabled
• Trustzone must be configured and in use
• The secure memory address space and the non-secure memory address space both use the same
physical addresses, either as an alias or the same memory location or for separate memory
locations
The issue is reported by ARM, erratum ID 468414, Category 2"

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-17 18:25:12 +02:00
Fabio Estevam
782b028841 mx5: lowlevel_init.S: Fix PLL settings for mx53
Currently PLL2 is not explicitely configured for mx53 and it runs at 333MHz.

Since PLL2 is the parent clock for DDR2, IPU, VPU, we should set it at 400MHz
instead.

Without doing so, it is not possible to use a 2.6.35 FSL kernel and display HDMI
at 1080p because the IPU clock cannot reach the requested frequency.

Set PLL2 to 400MHz, so that 1080p can be played and the DDR2 can run at its
maximum frequency.

Also, setup the other PLL's as done in FSL U-boot and re-arrange the code a little
bit to allow easier comparison with the original clock setup from FSL U-boot.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-17 18:09:34 +02:00
Fabio Estevam
758c344945 mx5: lowlevel_init.S: Split init_clock macro
init_clock is currently shared between mx51 and mx53 and it contains lots of
ifdef's which makes it really hard to follow the code.

Split the init_clock between mx51 and mx53 to allow easier readability.

No functional changes are made.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-17 18:09:34 +02:00
Benoît Thébaudeau
5676f598e7 mx25: Clean up imx-regs.h
Clean up i.MX25 imx-regs.h:
 - Update mx31 imx-regs.h filename.
 - Test for __KERNEL_STRICT_NAMES just in case.
 - Define internal RAM size.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-16 12:35:12 +02:00
Eric Nelson
f95c960bcc i.MX6: add HDMI transmitter register declarations from kernel WIP.
Original source from Pengutronix HDMI driver work:

	http://git.pengutronix.de/?p=imx/linux-2.6.git;a=commitdiff;h=72c31cd67ac880bd90785af86f8e46f8ea7b3bb0

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-16 12:35:11 +02:00
Eric Nelson
0fb1e57cb6 i.MX6: set drive strength for parallel RGB pads
Default drive strength is disabled and won't function.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-16 12:35:11 +02:00
Eric Nelson
5ae28d2db2 i.MX: iomux: input pad array can be const
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-16 12:35:11 +02:00
Fabio Estevam
dce67bd548 mx6qsabreauto: Pass the board revision to the kernel
The kernel from Freescale expects that the bootloader passes the board revision.

Read the board revision and pass it via get_board_rev().

Without passing the board revision the kernel does not operate properly as the
initialization of peripherals are different in revA versus revB boards.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-16 12:35:11 +02:00
Benoît Thébaudeau
6e3dc12754 mx35: Fix eSDHC clocks
Each eSDHC instance has a dedicated clock.

gd->sdhc_clk must also be set accordingly. This is good for the case only a
single SDHC instance is used (initialization made with fsl_esdhc_mmc_init()). A
future patch will fix the multi-instance use case (initialization made directly
with fsl_esdhc_initialize()).

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
2012-10-16 12:35:10 +02:00
Benoît Thébaudeau
151d63cb91 mx35: Clean up lowlevel_init
Clean up mx35 lowlevel_init:
 - Indent with tabs.
 - Fix comments.
 - Use defined values instead of literal constants.
 - Use defined macros instead of duplicating code.
 - Use macro parameters with default values instead of #define'd configs.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-16 12:35:10 +02:00
Tom Rini
bd23b22bad Merge branch 'agust@denx.de-next' of git://git.denx.de/u-boot-staging 2012-10-15 13:37:22 -07:00
Benoît Thébaudeau
85d993cef9 mx25: Clean up lowlevel_init
Clean up mx25 lowlevel_init:
 - Add comments.
 - Do not use write32 repeatedly with the same value in order not to increase
   code size.
 - Make register values configurable.
 - Use macro parameters with default values instead of literal constants.
 - Use defined macros instead of duplicating code.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Cc: Matthias Weisser <weisserm@arcor.de>
2012-10-15 11:54:14 -07:00
Benoît Thébaudeau
9e0081d573 mx31: Fix PDR0_CSI_PODF
The CSI PODF bit-field used by the previous code for the i.MX31 CCM PDR0
register is actually composed of two bit-fields: one pre-divider and one
post-divider. This patch fixes the CCM access macros and the code using them
accordingly.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:14 -07:00
Benoît Thébaudeau
b809b3ac13 mx35: Define MAX and AIPS registers
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:14 -07:00
Benoît Thébaudeau
df7e420bbd mx31: Add more CCM access macros
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:13 -07:00
Benoît Thébaudeau
dd227b6ea0 mx5: Optimize lowlevel_init code size
Optimize mx5 lowlevel_init.S code size:
 - Compute values at compile time rather than at runtime where possible.
 - Assign r4 to hold the zero value rather than setting registers to 0 again and
   again.
 - Associate a function to setup_pll rather than expanding its large macro code
   multiple times.
 - Allocate constant values in section only if used.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:13 -07:00
Benoît Thébaudeau
6be5800504 mx25: Fix eSDHC support
The MMC driver appropriate for the i.MX25 is fsl_esdhc, which has nothing to do
with mxcmmc.

Also, each eSDHC instance has a dedicated clock, so gd->sdhc_clk must be set
accordingly. This is good for the case only a single SDHC instance is used
(initialization made with fsl_esdhc_mmc_init()). A future patch will fix the
multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
2012-10-15 11:54:13 -07:00
Benoît Thébaudeau
f7542638c7 mx25: Define cpu_eth_init() only if needed
The FEC is the only SoC Ethernet support available on i.MX25, so define
cpu_eth_init() only for it instead of returning a misleading success code.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:13 -07:00
Benoît Thébaudeau
9baefa465d mx25: Clean up clocks API
Use the standard mxc_get_clock() instead of exporting internal functions and
using literal constant values.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:13 -07:00
Benoît Thébaudeau
17c7cf71b4 mx25 clocks: Fix MXC_FEC_CLK
mxc_get_clock(MXC_FEC_CLK) should return the IPG clock, not the AHB clock.

Also, imx_get_fecclk() was correct but reimplemented the calculation of the IPG
clock, so remove the duplicated code.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:13 -07:00
Benoît Thébaudeau
c3b5189031 mx25: Define more standard clocks
Define AHB, IPG and CSPI clocks.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:12 -07:00
Benoît Thébaudeau
fac7c817c3 mx25: Clean up clock calculations
Avoid possible overflow in clock calculations, and do not waste calls to lldiv()
to divide simple ulongs.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:12 -07:00
Benoît Thébaudeau
3c76add262 mx25: Fix decode_pll
The MFN bit-field of the PLL registers represents a signed value. See the
reference manual.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:12 -07:00
Benoît Thébaudeau
323846561a mx5/6 clocks: Fix SDHC clocks
The i.MX5 eSDHC clocks were considered as coming from the IPG clock although
they have dedicated clock paths.

Also, on i.MX5/6, each SDHC instance has a dedicated clock, so gd->sdhc_clk must
be set accordingly. This is good for the case only a single SDHC instance is
used (initialization made with fsl_esdhc_mmc_init()). A future patch will fix
the multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
2012-10-15 11:54:12 -07:00
Benoît Thébaudeau
be2f93b1ea mx51: Fix I2C clock ID check
There are only 2 I²C instances on i.MX51, but 3 on i.MX53.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:12 -07:00
Benoît Thébaudeau
d5fe220df4 mx5 clocks: Fix MXC_FEC_CLK
The FEC clock does not come from PLL1, but from the IPG clock. The previous code
was even inconsistent with itself, returning the IPG clock as expected for
imx_get_fecclk(), but the PLL1 clock for mxc_get_clock(MXC_FEC_CLK).

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:12 -07:00
Benoît Thébaudeau
3cbd107b5f mx5 clocks: Simplify imx_get_cspiclk()
The code handling the dividers was duplicated for each possible input clock, and
this function can benefit from the newly introduced get_standard_pll_sel_clk()
function instead of duplicating this mux handling code.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:11 -07:00
Benoît Thébaudeau
08028b113e mx5 clocks: Fix get_uart_clk()
This function returned 66500000 instead of the correct lp_apm clock frequency if
the CCM.CSCMR1.uart_clk_sel mux is set to 3.

This patch fixes this issue by introducing the get_standard_pll_sel_clk()
function that will be used by future patches to handle identical muxes used by
many other clocks.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:11 -07:00
Benoît Thébaudeau
f124e718f4 mx5 clocks: Fix get_ipg_per_clk()
This fixes the "IPG PERCLK" frequency printed by the clocks command. The issue
was that get_ipg_per_clk() used periph_clk instead of lp_apm in the case
CCM.CBCMR.perclk_lp_apm_sel is set.

It also fixes I²C support.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:11 -07:00
Benoît Thébaudeau
55c8df0cb1 mx5 clocks: Fix get_periph_clk()
In the case periph_clk comes from periph_apm_clk, the latter is selected by the
CCM.CBCMR.periph_apm_sel mux, which can source the lp_apm clock from its
input ♯2. get_periph_clk() returned 0 instead of the lp_apm clock frequency in
this case.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:11 -07:00
Benoît Thébaudeau
b94792982f mx5 clocks: Fix get_lp_apm()
If CCM.CCSR.lp_apm is set, the lp_apm clock is not necessarily 32768 Hz x 1024.
In that case:
 - on i.MX51, this clock comes from the output of the FPM,
 - on i.MX53, this clock comes from the output of PLL4.

This patch fixes the code accordingly.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:11 -07:00
Benoît Thébaudeau
649dc8abd9 mx5 clocks: Add and use CCSR definitions
This fixes config_pll_clk(), which used 0x20 instead of 0x200 for PLL4_CLOCK.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:11 -07:00
Benoît Thébaudeau
414e1660c8 mx51: Fix USB PHY clocks
The i.MX51 has a single USB PHY clock, while the i.MX53 has two. These 3 clocks
have different clock gate control bit-fields.

The existing code was correct only for i.MX53, so this patch fixes the i.MX51
use case.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Jana Rapava <fermata7@gmail.com>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
2012-10-15 11:54:11 -07:00
Benoît Thébaudeau
248cdf0b52 mx5: Fix clock gate values
The clock gate values are 2-bit bit-fields. Hence, setting or clearing only one
of these bits like what was done is wrong and can lead to unpredictable behavior
depending on the original value of these bit-fields.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:10 -07:00
Benoît Thébaudeau
1f5e4ee0b9 mx5: Use explicit clock gate names
Use clock gate definitions having names showing clearly the gated clock instead
of names giving only a register field index.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:10 -07:00
Benoît Thébaudeau
846b38981f mx5 clocks: Cleanup
Clean up the i.MX5 clock driver:
 - Use readl() and writel() instead of their __raw_ counterparts.
 - Use the clr/setbits_le32() family of macros rather than expanding code.
 - Use accessor macros for bit-fields instead of _MASK and _OFFSET.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:10 -07:00
Benoît Thébaudeau
833b6435de mx5/6: Define default SoC input clock frequencies
Define default SoC input clock frequencies for i.MX5/6 in order to get rid of
duplicated definitions.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15 11:54:10 -07:00
Matthias Weisser
e7bed5c2b3 imx: Use MXC_I2C_CLK in imx i2c driver
i2c didn't work on imx25 due to missing MXC_IPG_PERCLK. Now using
MXC_I2C_CLK on all imx systems using i2c.

Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:10 -07:00
Eric Benard
8a57fdc640 mx25: add CPU revision 1.2
tested on a MCIMX257CJM4A which now reports :
CPU:   Freescale i.MX25 rev1.2 at 399 MHz

Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2012-10-15 11:54:10 -07:00
Eric Nelson
2af7e81015 i.MX6: get rid of redundant struct src_regs (dupe of struct src)
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15 11:54:09 -07:00
Eric Nelson
de710a14b5 i.MX6: define struct iomuxc and IOMUX_GPR2 register bitfields
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:09 -07:00
Eric Nelson
e66ad6e747 i.MX6: Add ANATOP_PFD_480 bitfield constants
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:09 -07:00
Eric Nelson
a83e1b7b8c i.MX6: define IOMUX_GPR3 register bitfields
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2012-10-15 11:54:09 -07:00