Use quad write if SPI_TX_QUAD flag is set.
Tested quad write on Stratix 10 SoC board (Micron
serial NOR flash, mt25qu02g)
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Marvell's switch chips with integrated CPUs (collectively referred to as
MSYS) share common ancestry with the Armada SoCs. Some of the IP blocks
(e.g. xor) are located at different addresses and DFX server exists as a
separate target on the MBUS (on Armada-38x it's just part of the core
complex registers).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The kirkwood devices are compatible with this driver.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Fix the worng include and offset macros.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This fixes a compile error on kirkwood.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
With board_ahci_enable() implementation for Armada 38x in place we can
now enable 38x support in the ahci_mvebu driver.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds DM support to the Armada XP SATA driver. This is needed
to enable CONFIG_BLK on this platform. It adds the SATA controller as
AHCI device, which is strictly speaking not correct, as the controller
is not AHCI compatible. But the U-Boot AHCI uclass interface enables
the usage of this DM driver and the creation of the corresponding BLK
devices.
This conversion is done to get rid of the compile warning:
Reviewed-by: Chris Packham <judge.packham@gmail.com>
===================== WARNING ======================
This board does not use CONFIG_DM_SCSI. Please update
the storage controller to use CONFIG_DM_SCSI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The generic wdt_start API expects to be called with the timeout in
milliseconds. Update the orion_wdt driver to accept a timeout in
milliseconds and use the clock rate specified in the dts to convert the
timeout to an appropriate value for the timer reload register.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
When run from the SPL the mvebu targets are using the hardware default
offset for the SoC peripherals. devfdt_get_addr_size_index() understands
how to deal with this via dm_get_translation_offset() so use this
instead of fdtdec_get_addr_size_auto_noparent().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The function dm_ofnode_pre_reloc should be used instead
of the function dm_fdt_pre_reloc and avoid duplicated code.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
v2019.04-rc3 sandbox U-Boot fails to boot when compiled with
-fsanitize=address and linked against -lasan, reporting [1].
Git bisecting shows that the issue is contributed by v2019.01 commit
1678754f5e ("core: ofnode: Fix ofnode_get_addr_index function").
The root cause seems to be the mismatch between sizeof(u64) and
sizeof(fdt_size_t) on sandbox. Luckily, thanks to the fact that the
size argument of both of_get_address() and fdtdec_get_addr_size_fixed()
is optional, we can pass NULL in its place, avoiding the problem.
[1] Backtrace reported by ASAN (gcc 8.1.0):
$> ./u-boot -d arch/sandbox/dts/sandbox.dtb
[..]
Reviewed-by: Simon Glass <sjg@chromium.org>
=================================================================
==10998==ERROR: AddressSanitizer: stack-buffer-overflow on address 0x7ffcc2331140 at pc 0x0000004eeeb0 bp 0x7ffcc2330f80 sp 0x7ffcc2330f70
WRITE of size 8 at 0x7ffcc2331140 thread T0
#0 0x4eeeaf in of_get_address drivers/core/of_addr.c:154
#1 0x4f7441 in ofnode_get_addr_index drivers/core/ofnode.c:263
#2 0x5b2a78 in sb_eth_ofdata_to_platdata drivers/net/sandbox.c:422
#3 0x4dccd8 in device_probe drivers/core/device.c:407
#4 0x753170 in eth_initialize net/eth-uclass.c:428
#5 0x47d9bf in initr_net common/board_r.c:557
#6 0x6bcfa7 in initcall_run_list lib/initcall.c:30
#7 0x47e1fe in board_init_r common/board_r.c:859
#8 0x4060e5 in main arch/sandbox/cpu/start.c:356
#9 0x7fb8d135482f in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2082f)
#10 0x40a3a8 in _start (/path/to/u-boot/u-boot+0x40a3a8)
Address 0x7ffcc2331140 is located in stack of thread T0 at offset 32 in frame
#0 0x4f72b8 in ofnode_get_addr_index drivers/core/ofnode.c:255
This frame has 3 object(s):
[32, 36) 'size' <== Memory access at offset 32 partially overflows this variable
[96, 100) 'flags'
[160, 168) 'node'
HINT: this may be a false positive if your program uses some custom stack unwind mechanism or swapcontext
(longjmp and C++ exceptions *are* supported)
SUMMARY: AddressSanitizer: stack-buffer-overflow drivers/core/of_addr.c:154 in of_get_address
Shadow bytes around the buggy address:
0x10001845e1d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x10001845e1e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x10001845e1f0: 00 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1
0x10001845e200: 04 f2 f2 f2 f2 f2 f2 f2 04 f2 f2 f2 f2 f2 f2 f2
0x10001845e210: 04 f2 f2 f2 f3 f3 f3 f3 00 00 00 00 00 00 00 00
=>0x10001845e220: 00 00 00 00 f1 f1 f1 f1[04]f2 f2 f2 f2 f2 f2 f2
0x10001845e230: 04 f2 f2 f2 f2 f2 f2 f2 00 f2 f2 f2 f3 f3 f3 f3
0x10001845e240: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x10001845e250: 00 00 00 00 f1 f1 f1 f1 00 00 f2 f2 f3 f3 f3 f3
0x10001845e260: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f1 f1
0x10001845e270: f1 f1 00 f2 f2 f2 f3 f3 f3 f3 00 00 00 00 00 00
Shadow byte legend (one shadow byte represents 8 application bytes):
Addressable: 00
Partially addressable: 01 02 03 04 05 06 07
Heap left redzone: fa
Freed heap region: fd
Stack left redzone: f1
Stack mid redzone: f2
Stack right redzone: f3
Stack after return: f5
Stack use after scope: f8
Global redzone: f9
Global init order: f6
Poisoned by user: f7
Container overflow: fc
Array cookie: ac
Intra object redzone: bb
ASan internal: fe
Left alloca redzone: ca
Right alloca redzone: cb
==10998==ABORTING
'To' list:
git log --since=1year drivers/core/ofnode.c | grep "\-by: .*@" | \
sed 's/.*-by: //' | sort | uniq -c | sort -rn
10 Simon Glass <sjg@chromium.org>
3 Mario Six <mario.six@gdsys.cc>
2 Martin Fuzzey <mfuzzey@parkeon.com>
2 Marek Vasut <marek.vasut+renesas@gmail.com>
1 Tom Rini <trini@konsulko.com>
1 Masahiro Yamada <yamada.masahiro@socionext.com>
1 Keerthy <j-keerthy@ti.com>
1 Jens Wiklander <jens.wiklander@linaro.org>
1 Bin Meng <bmeng.cn@gmail.com>
Fixes: 1678754f5e ("core: ofnode: Fix ofnode_get_addr_index function")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Change the function syscon_regmap_lookup_by_phandle()
introduced by commit 6c3af1f24e ("syscon: dm: Add a
new method to get a regmap from DTS") to have
Linux-compatible syscon API.
Same modification than commit e151a1c288 ("syscon: add
Linux-compatible syscon API") solves issue when the node
identified by the phandle has several compatibles and is
already bound to a dedicated driver.
See Linux commit bdb0066df96e ("mfd: syscon: Decouple syscon
interface from platform devices").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some binding define child node gpio-controller without compatible property.
This patch avoid to bind the pinconfig uclass to these node.
For example, the binding for st,stm32-pinctrl
(./device-tree-bindings/pinctrl/st,stm32-pinctrl.txt) defines the GPIO
controller/bank node as sub-node of pincontrol (st,stm32f429-pinctrl)
but without compatible (as it is not mandatory).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In case of system with several pin-controller device, probe the first
UCLASS_PINCTRL by seq number (defined by alias) to avoid race condition
with I2C PINCONTROL driver for GPIO expander (GPIO expander need I2C bus,
I2C driver need PINCONFIG).
Signed-off-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit 5ff7768892.
As noted in the comment, the function pinctrl_decode_pin_config_dm()
only served as a temporary solution.
Since the function has no users anymore, we can remove it again.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We can remove the pre reloc property in SPL and TPL device-tree:
- u-boot,dm-pre-reloc
- u-boot,dm-spl
- u-boot,dm-tpl
As only the needed node are kept by fdtgrep (1st pass).
The associated function (XXX_pre_reloc) are simple for SPL/TPL:
return always true.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Merge drivers/soc/keystone/ into drivers/soc/ti/
and convert CONFIG_TI_KEYSTONE_SERDES into Kconfig.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The UDMA-P is intended to perform similar (but significantly upgraded) functions
as the packet-oriented DMA used on previous SoC devices. The UDMA-P module
supports the transmission and reception of various packet types.
The UDMA-P also supports acting as both a UTC and UDMA-C for its internal
channels. Channels in the UDMA-P can be configured to be either Packet-Based or
Third-Party channels on a channel by channel basis.
The initial driver supports:
- MEM_TO_MEM (TR mode)
- DEV_TO_MEM (Packet mode)
- MEM_TO_DEV (Packet mode)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
The Ring Accelerator (RINGACC or RA) provides hardware acceleration to
enable straightforward passing of work between a producer and a consumer.
There is one RINGACC module per NAVSS on TI AM65x SoCs.
The RINGACC converts constant-address read and write accesses to equivalent
read or write accesses to a circular data structure in memory. The RINGACC
eliminates the need for each DMA controller which needs to access ring
elements from having to know the current state of the ring (base address,
current offset). The DMA controller performs a read or write access to a
specific address range (which maps to the source interface on the RINGACC)
and the RINGACC replaces the address for the transaction with a new address
which corresponds to the head or tail element of the ring (head for reads,
tail for writes). Since the RINGACC maintains the state, multiple DMA
controllers or channels are allowed to coherently share the same rings as
applicable. The RINGACC is able to place data which is destined towards
software into cached memory directly.
Supported ring modes:
- Ring Mode
- Messaging Mode
- Credentials Mode
- Queue Manager Mode
TI-SCI integration:
Texas Instrument's System Control Interface (TI-SCI) Message Protocol now
has control over Ringacc module resources management (RM) and Rings
configuration.
The Ringacc driver manages Rings allocation by itself now and requests
TI-SCI firmware to allocate and configure specific Rings only. It's done
this way because, Linux driver implements two stage Rings allocation and
configuration (allocate ring and configure ring) while TI-SCI Message
Protocol supports only one combined operation (allocate+configure).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Texas Instruments' System Control Interface (TI-SCI) Message Protocol
abstracts management of NAVSS resources, like PSI-L pairing and
unpairing, UDMAP tx/rx/flow configuration and Rings.
This patch adds support for requesting and configuring such resources
from TI-SCI firmware.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
The chip_desc.enable field is used only for muxes, not for switches.
Document it and remove the unused values.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher<hs@denx.de>
The Kconfig help has not been updated while adding PCA9547 and PCA9646.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher<hs@denx.de>
The 'u-boot,i2c-transaction-bytes' device tree property provides
information regarding number of bytes transferred by a device in a
single transaction.
This change is necessary to avoid hanging devices after soft reset.
One notable example is communication with MC34708 device:
1. Reset when communicating with MC34708 via I2C.
2. The u-boot (after reboot -f) tries to setup the I2C and then calls
force_idle_bus. In the same time MC34708 still has some data to be sent
(as it transfers data in 24 bits chunks).
3. The force_idle_bus() is not able to make the bus idle as 8 SCL
clocks may be not enough to have the full transmission.
4. We end up with I2C inconsistency with MC34708.
This PMIC device requires 24+ SCL cycles to make finish any pending I2C
transmission.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reset and initialize the PHY once in the probe() function rather than
doing it over and over again is start() function. This requires us to
keep the clock enabled while the driver is in use. This significantly
reduces the time between transfers as the PHY doesn't have to restart
autonegotiation between transfers, which takes forever.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Synchronize R-Car Gen3 pin control tables with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize R-Car Gen2 pin control tables with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Linux 5.0, commit 1c163f4c7b3f621efff9b28a47abb36f7378d783,
has a TDSEL fix for R8A7790 H2 and R8A7794 E2 SoCs, implement
similar fix for U-Boot. The difference here is that the SoC
ES matching has to be implemented manually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add pin control tables for R8A77965 from Linux 5.0 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add clock tables for R8A77965 from Linux 5.0 , except for the
crit, R and Z clock, which are neither used nor supported by
the U-Boot clock framework yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There exists code in drivers/common/common.c to read the dr_mode
from the device tree. This patch converts this driver to use that
function to initialize the driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
Drop the counter, it has no meaning other than being the order in which
the interface is found; the name assigned to the USB host controller
interface is a better indicator.
Example of the original output:
> USB0: USB EHCI 1.10
> scanning bus 0 for devices... 2 USB Device(s) found
> scanning usb for storage devices... 1 Storage Device(s) found
Patched output:
> Bus usb@ee080100: USB EHCI 1.10
> scanning bus usb@ee080100 for devices... 2 USB Device(s) found
> scanning usb for storage devices... 1 Storage Device(s) found
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
I've noticed that the first ethernet packet after PHY link establishment
is not tranferred correctly most of the time on my AT91SAM9G25 board.
Here I usually see a timeout of a few seconds, which is quite
annoying.
Adding a small delay (10ms in this case) after the link establishment
helps to solve this problem. With this patch applied, this timeout
on the first packet is not seen any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
SAM9X60 uses high and low drive strengths. To implement this, in
at91_pinctrl_mux_ops::set_drivestrength we need bit numbers of
drive strengths (1 for low, 2 for high), thus change the code to
allow the usage of drive strength bit numbers.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
This patch enables and starts the watchdog on the AT91 platform if
configured. The WD timeout value is read in the AT91 WD device driver
from the DT, using the "timeout-sec" DT property. If not provided in
the DT, the default value of 2 seconds is used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
This patch removes the CONFIG_AT91_HW_WDT_TIMEOUT as its not needed any
more. The WD timeout value can be provided via the "timeout-sec" DT
property. If not provided this way, the default value of 2 seconds will
be used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
This patch fixes the timer register setup in at91_wdt_start() to
correctly configure the register again. The input timeout value is
now in milli-seconds instead of seconds with the new watchdog API.
Make sure to take this into account and only use a max timeout
value of 16 seconds as appropriate for this SoC.
Also the check against a lower timeout value than 0 is removed. This
check makes no sense, as the timeout value is unsigned.
Signed-off-by: Stefan Roese <sr@denx.de>
Reported-by: Heiko Schocher <hs@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board:
Tested-by: Heiko Schocher <hs@denx.de>
This patch adds an alterative SPL version of atmel_serial_enable_clk().
This enables the usage of this driver without full clock support (in
drivers and DT nodes). This saves some space in the SPL image.
Please note that this fixed clock support is only added to the SPL code
in the DM_SERIAL part of this file. All boards not using SPL & DM_SERIAL
should not be affected.
This patch also introduces CONFIG_SPL_UART_CLOCK for the fixed UART
input clock. It defaults to 132096000 for ARCH_AT91 but can be set to
a different value if needed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Before printk.h was introduced and MTDDEBUG was removed,
pr_crit() was calling MTDDEBUG(), which was since then
replaced by the current pr_debug().
pr_debug is more appropriate here.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add a new definition for ubi_assert and keep
the original one in an ifndef __UBOOT__.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
As per Linux kernel DT binding doc:
- phy-reset-post-delay : Post reset delay in milliseconds. If present then
a delay of phy-reset-post-delay milliseconds will be observed after the
phy-reset-gpios has been toggled. Can be omitted thus no delay is
observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Negative phy-addresses can occour if the caller function was not able to
determine a valid phy address (from device-tree for example). In this
case we catch this here and search for ANY phy device on the given mdio-
bus.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Lukasz Majewski <lukma@denx.de>
The MESON_GXL_USB_PHY is also used on the Amlogic Meson GXM SoCs.
Fixes: 2960e27e38 ("phy: Add Amlogic Meson USB2 & USB3 Generic PHY drivers")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
CLK_AHB_GMAC was suppose to be part of previous commit
"clk: sunxi: Implement A10 EMAC clocks" add it so-that
we can get rid of sunxi_set_gate warning on boot message.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- reverts the deprecation of the 'download-key' detection
(with a full solution pending for the next release)
- applies a temporary fix for the 32bit pinctrl registers on the RK3288
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcnoA9AAoJECaAFcEOcohNRYYH/0SAGKro+gO1q07xpBLGbOSL
MJPNDQ853IpH+kI+Mc+VFeFZz8fuQHae2aKfgmHmEGGSygFqAKXvMUgG73XO8Z27
Ov9r0RgR5s35eXFC0URqcDSCuTtFSP/MdmSy2hO546pJOapHhmx/eZUId3ZFjSe5
puIQfTxK0zbNqfFlfjsRnkXhR9jhYVvPtSpFYYjCeU/dRB4/OUzNHQjwjkdB8ru1
mTLmrhqqZ4fq3t9JMrxCH3COvI6QYBXj73ynKYtJ4lByh3NdIz0a37F99FiWgH2X
0WptUN8tjjZP+2BboVNo6io/12YxE6V+wG2LGEXreS9ubMr4nm+LXqDCoZIB7MM=
=ESBv
-----END PGP SIGNATURE-----
Merge tag 'rockchip-fixes-for-2019.04' of git://git.denx.de/u-boot-rockchip
Last-minute fixes for Rockchip for 2019.04:
- reverts the deprecation of the 'download-key' detection
(with a full solution pending for the next release)
- applies a temporary fix for the 32bit pinctrl registers on the RK3288
After the commit b9a2a0e2e9 ("mmc: Add support for downgrading
HS200/HS400 to HS mode"), it add a parameter in mmc_set_card_speed()
which indicates that the HS200/HS400 to HS downgrade is happening.
During the HS400 initialization, first select to HS200, and config
the related clock rate, then downgrade to HS mode. So here also need
to config the downgrade value to be true for two reasons. First,
make sure in the function mmc_set_card_speed(), after switch to HS
mode, first config the clock rate, then read the EXT_CSD, avoid
receiving data of EXT_CSD in HS mode at 200MHz. Second, after issue
the MMC_CMD_SWITCH command, it need to wait a bit then switch bus
properties.
Test on i.MX8QM MEK board, some Micron eMMC will stuck in transfer
mode in this case, and USDHC will never get data transfer complete
status, cause the uboot hang.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
There are no higher 16 writing corresponding bits for pmu_gpio0's
iomux/drive/pull at rk3288, need to read the value from register
firstly. Add the flag to distinguish it from normal registers.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Currently, HDMI driver doesn't consider minimum and maximum allowed rate
of pll3 (video PLL). It works most of the time, but not always.
Consider monitor with resolution 1920x1200, which has pixel clock rate
of 154 MHz. Current code would determine that pll3 rate has to be set to
154 MHz. However, minimum supported rate is 192 MHz. In this case video
output just won't work.
The reason why the driver is written in the way it is, is that at the
time HDMI PHY and clock configuration wasn't fully understood. But now
we have needed knowledge, so the issue can be fixed.
With this fix, clock configuration routine uses full range (1-16) for
clock divider instead of limited one (1, 2, 4, 11). It also considers
minimum and maximum allowed rate for pll3.
Fixes: 56009451d8 ("sunxi: video: Add A64/H3/H5 HDMI driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED
I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
On 16bit variants of the TMIO SD IP, the SECCNT register can only be
programmed to 16bit values, while on the 32bit and 64bit variants it
can be programmed to 32bit values. The SECCNT register indicates the
maximum number of blocks in a continuous transfer. Hence, limit the
maximum continuous transfer block count to 65535 blocks on 16bit
variants of the TMIO IP and to BIT(32)-1 blocks on 32bit and 64bit
variants.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Set MMCIF clock rate to 97.5 MHz, which is the default according
to Gen2 datasheet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Add code for configuring the MMC0CKCR/MMC1CKCR on Gen2 platforms.
This allows the MMCIF driver to set higher clock rate if desired.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The $div and $mul values were swapped in the debug output,
fix this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The gen2_clk_get_sdh_div() function is supposed to look up the
$val value read out of the SDCKCR register in the supplied table
and return the matching divider value. The current implementation
was matching the value from SDCKCR on the divider value in the
table, which is wrong. Fix this and rework the function a bit
to make it more readable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The tiny printf implementation only supports %x format specifier,
it does not support %X . Since it makes little difference whether
the debug output prints hex numbers in capitals or not, change it
to %x and make the MMC_TRACE output work with tiny printf too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
This patch fixes below warnings found with checker tool.
The variable len in i2c_msg struct is of unsigned type
and it is received as recv_count which is unsigned type
but it is checked with < 0 which is always false, hence
removed it.
The local variable curr_recv_count is declared as signed
type and compared aginst unsigned recv_count which is
incorrect. This is fixed by declaring it as unsigned type.
drivers/i2c/i2c-cdns.c: In function ‘cdns_i2c_read_data’:
drivers/i2c/i2c-cdns.c:317:18: warning: comparison of
unsigned expression < 0 is always false [-Wtype-limits]
if ((recv_count < 0))
^
drivers/i2c/i2c-cdns.c:340:24: warning: comparison of
integer expressions of different signedness:
‘u32’ {aka ‘unsigned int’} and ‘int’ [-Wsign-compare]
updatetx = recv_count > curr_recv_count;
^
drivers/i2c/i2c-cdns.c:361:39: warning: comparison of
integer expressions of different signedness:
‘u32’ {aka ‘unsigned int’} and ‘int’ [-Wsign-compare]
while (readl(®s->transfer_size) !=
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
- Enable network interface on clearfog_gt_8k (Baruch)
- Fix dreamplug boot by adding an spi0 alias to the DT (Chris)
- Fix / enhance Marvell ddr3 setup / parameters (Chris)
- Change CONFIG_SYS_MALLOC_F_LEN to 0x2000 on db-88f6820-amc (Chris)
- Enable SPL_FLASH_BAR on db-88f6820-amc (Chris)
- Use correct pcie controller name in Armada-38x dts files (Chris)
- Disable d-cache on Kirkwood platforms as currently needed (Chris)
- Add a more descriptive comment to pci_mvebu.c (Stefan)
- Update Marvell maintainers entry (Stefan)
Inactive chip-selects will give invalid values for read_sample so don't
consider them when trying to determine the overall min/max read sample.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/18]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Based on the JEDEC standard JESD79-3F. The tRAS timings should include
the highest speed bins at a given frequency. This is similar to commit
683c67b ("mv_ddr: ddr3: fix tfaw timimg parameter") where the wrong
comparison was used in the initial implementation.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/15]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds a comment to explain the use of the hardcoded value for
the number of address cells in mvebu_get_tgt_attr(). This should help to
rework this function, once CONFIG_OF_LIVE is enabled for MVEBU in
general.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
When booting on a 64-bit system, the boot_addr_start buffer is not
large enough to contain a 64-bit number, thus leading to a crash
even if fastboot_buf_addr is valid, only the high part of the address
will be printed to boot_addr_start :
fastboot with fastboot_buf_addr = 0x0000000006000000:
downloading of 92239872 bytes finished
Booting kernel at 0x00000000...
"Synchronous Abort" handler, esr 0x96000004
elr: 00000000010561f4 lr : 0000000001056fac (reloc)
<snip>
x28: 000000007df2d38f x29: 000000007df2d1b0
Resetting CPU ...
With this fix, boot_addr_start can have the full 64-bit address passed
to bootm.
Fixes: f73a7df984 ("net: fastboot: Merge AOSP UDP fastboot")
Cc: Simon Glass <sjg@chromium.org>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
commit 801f1fa442 "dm: usb: udc: Use SEQ_ALIAS to index the USB gadget
ports" changed the way the udevice if found. It uses the alias to find
a udevice for a given USB port number. In the commit log it was stated
that if no alias is provided, the bind order will be used instead. However
it doesn't work. Fixing this by adding a call to uclass_get_device() if
uclass_get_device_by_seq() fails.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Vignesh R <vigneshr@ti.com>
If node /board_info/ports does not exist in the DPC file,
function mc_fixup_dpc() will skip not only MAC address fixup,
but also the cache flush at the end. This may cause the other
fixup changes (e.g. ICID related ones) to be ignored by MC.
Fixes: 1161dbcc0a ("drivers: net: fsl-mc: Include MAC addr fixup to DPL")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
some dpmacs in armv8a based freescale layerscape SOCs can be
configured via both serdes(sgmii, xfi, xlaui etc) bits and via
EC*_PMUX(rgmii) bits in RCW.
e.g. dpmac 17 and 18 in LX2160A can be configured as SGMII from
serdes bits and as RGMII via EC1_PMUX/EC2_PMUX bits
Now if a dpmac is enabled by serdes bits then it takes precedence
over EC*_PMUX bits. i.e. in LX2160A if we select serdes protocol
that configures dpmac17 as SGMII and set the EC1_PMUX as RGMII,
then the dpmac is SGMII and not RGMII.
Therefore, in fsl_rgmii_init function of SOC, we will check if the
dpmac is enabled or not? if it is (fsl_serdes_init has already enabled
the dpmac), then don't enable it.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The phy_connect_dev(...) function from phy.c does all the handling
(inclusive catching fixed-link).
So we drop here the single steps and call just phy_connect_dev(...).
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently the spl system calls nand_init which does nothing.
It isn't until an attempt to load from NAND that it gets initialized.
Subsequent attempts to load just skip the initialization because
NAND is already initialized.
This moves the contents of mxs_nand_init to nand_init. In the event
of an error, it clears the number of nand chips found. Any
attempts to use nand will check if there are nand chips available
instead of actually doing the initialization at that time. If there
are none, it will return an error to the higher level calls.
Signed-off-by: Adam Ford <aford173@gmail.com>
Kconfig allows boards to configured with DM_SERIAL and still
have SPL_DM_SERIAL disabled. This patch changes the ifdef's
to CONFIG_IS_ENABLED to allow the modes to differ between
SPL and U-Boot.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix an error with the serial communication on boards with a very small
UART buffer which leads to a stalled system.
Provide an X86 reset driver for the UEFI runtime.
-----BEGIN PGP SIGNATURE-----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=JKJm
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-04-rc4-2' of https://github.com/xypron2/u-boot
Pull request for UEFI system for v2019.04-rc4
Fix an error with the serial communication on boards with a very small
UART buffer which leads to a stalled system.
Provide an X86 reset driver for the UEFI runtime.
According to datasheet, the output on LDO regulators will start
appearing after 10-15 us.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Changing voltage and enabling regulator might require delays so the
regulator stabilizes at expected level.
Add support for "regulator-ramp-delay" binding which can introduce
required time to both enabling the regulator and to changing the
voltage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
When stopping the ADC_V2_CON1_STC_EN should be cleared.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Our selftest will soon test the actual runtime reset function rather than
the boot time one. For this, we need to ensure that the runtime version
actually succeeds on x86 to keep our travis tests work.
So this patch implements an x86 runtime reset function. It is missing
shutdown functionality today, but OSs usually implement that via ACPI
and this function does more than the stub from before, so it's at least
an improvement.
Eventually we will want to have full DM functionality in runtime services.
But this fixes a travis failure and doesn't clutter the code too heavily, so
we should pull it in without the amazing new RTS DM framework.
Signed-off-by: Alexander Graf <agraf@suse.de>
Replace the current rather convoluted code using ad-hoc polling
mechanism with a more straightforward code. Use wait_for_bit_le32()
to poll the DDRCALSTAT register instead of local reimplementation.
It makes no sense to pull for 5 seconds before giving up and trying
to restart the EMIF, so instead wait 500 mSec for the calibration to
complete and if this fails, restart the EMIF and try again. Perform
this 32 times instead of 3 times as the original code did.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
The EMIF reset code can well use wait_for_bit_le32() instead of all that
convoluted polling code. Reduce the timeout from 100 seconds to 1 second,
since if the EMIF fails to reset itself in 1 second, it's unlikely longer
wait would help. Make sure to clear the EMIF reset request even if the
SEQ2CORE_INT_RESP_BIT isn't asserted.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
The current EMIF clear timeout handling code was applying bitwise
operations to signed data types and as it was, was extremely hard
to read. Replace it with simple wait_for_bit(). Expand the error
handling to make it more readable too.
This patch also changes the timeout for emif_clear() from 14 hours
to 1 second.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
