As we have more legacy PMIC drivers to move to Kconfig, guard them all
with POWER_LEGACY or SPL_POWER_LEGACY. Do the same kind of check for
building the drivers too. This also means that we need to resort the
list slightly in the Makefile.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_PCI and
CONFIG_SYS_PCIE namespace do not easily transition to Kconfig. In many
cases they likely should come from the device tree instead. Move these
out of CONFIG namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These RTC drivers are currently unused and reference other unused CONFIG
variables, so remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NUM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NS16550
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SPL_NS16550_MIN_FUNCTIONS
CONFIG_SYS_NS16550_MEM32
CONFIG_SYS_NS16550_PORT_MAPPED
CONFIG_SYS_NS16550_REG_SIZE
CONFIG_SYS_NS16550_SERIAL
To do this we also introduce CONFIG_SPL_SYS_NS16550_SERIAL so that
platforms can enable the legacy driver here for SPL.
Signed-off-by: Tom Rini <trini@konsulko.com>
This symbol is specific to the PowerPC SPL implementation, so rename
this to reflect that it's in SPL and used / tested there, so that we can
then safely migrate it to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NAND
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_PAGE_2K
CONFIG_SYS_NAND_PAGE_4K
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_MAX_OOBFREE
CONFIG_SYS_NAND_MAX_ECCPOS
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is the only driver, and only one platform makes use of, setting
CONFIG_SYS_NAND_ECC_BASE. Reference ATMEL_BASE_ECC directly in this
case.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_HW_ECC
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_HW_ECC_OOBFIRST
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_DBW_8
CONFIG_SYS_NAND_DBW_16
Note that all instances of the code check for CONFIG_SYS_NAND_DBW_16
being defined, and then "else" to CONFIG_SYS_NAND_DBW_8 whereas all of
the configs set CONFIG_SYS_NAND_DBW_8. So we introduce
CONFIG_SYS_NAND_DBW_16 as an option.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
xilinx:
- Fix MAC address selection for System Controller from FRU
- Cleanup Kconfig (ZYNQ_MAC_IN_EEPROM symbol)
versal:
- Create u-boot.elf for mini spi configurations
versal-net:
- Enable MT35XU flash
zynq:
- Add missing timer to DT for mini configurations
zynqmp:
- Do not include psu_init to U-Boot by default
- Do not enable IPI by default to mini U-Boot
- Update Luca's fragment
- Fix SPL_FS_LOAD_PAYLOAD_NAME usage
spi:
- gqspi: Fix tapdelay values
- gqspi: Fix 64bit address support
- cadence: Remove condition for calling enable linear mode
- nor-core: Invert logic to reflect sst26 flash unlocked
net:
- Add PCS/PMA phy support
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCY422rQAKCRDKSWXLKUoM
ITrXAJ9sVsVNwnjS99ZdNg64zx/Y5mSRlgCdGMho9/PT6BRmOV4IygwOsEGy7I8=
=XsS5
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.01-rc3-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2023.01-rc3-v2
xilinx:
- Fix MAC address selection for System Controller from FRU
- Cleanup Kconfig (ZYNQ_MAC_IN_EEPROM symbol)
versal:
- Create u-boot.elf for mini spi configurations
versal-net:
- Enable MT35XU flash
zynq:
- Add missing timer to DT for mini configurations
zynqmp:
- Do not include psu_init to U-Boot by default
- Do not enable IPI by default to mini U-Boot
- Update Luca's fragment
- Fix SPL_FS_LOAD_PAYLOAD_NAME usage
spi:
- gqspi: Fix tapdelay values
- gqspi: Fix 64bit address support
- cadence: Remove condition for calling enable linear mode
- nor-core: Invert logic to reflect sst26 flash unlocked
net:
- Add PCS/PMA phy support
flash_is_locked is changed to flash_is_unlocked with commit 513c6071ce
("mtd: spi: Convert is_locked callback to is_unlocked"). sst26_is_locked()
is also changed to sst26_is_unlocked() but the logic remained same.
Invert the logic for the flash lock/unlock to work properly.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20221122051833.13306-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
cadence_qspi_apb_enable_linear_mode() has a weak function defined, so no
need to gaurd this under if (CONFIG_IS_ENABLED(ARCH_VERSAL)).
In cadence_qspi_apb_write_execute(), enable linear mode is called twice by
mistake, remove extra one.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221129114134.18909-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When we pass the 64-bit address to read/write, only lower 32-bit
address is getting updated. Program the upper 32-bit address in the
DMA destination memory address MSBs register, which can handle upto
44-bit destination address.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221125104413.26140-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The driver was using an incorrect value for GQSPI_LPBK_DLY_ADJ_DLY_1
tapdelay for Versal for frequencies above 100MHz. Change it from 2 to 1
based on the recommended value in IP spec.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20221123090451.11409-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Both PCS/PMA PHY and the external PHY need to have a valid link status
in order to have Ethernet traffic. Check and wait this status at
setup_phy() so that we could diagnose if there is a PHY issue.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Link: https://lore.kernel.org/r/20221101035800.912644-3-andy.chiu@sifive.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
If we bridge an external PHY to Xilinx's PCS/PMA PHY and would like to
get and set the real status of the PHY facing the external world. Then
we should phy_connect() to the external PHY instead of the PCS/PMA one.
Thus, we add a pcs-handle DT entry, which have been merged in Linux, and
leave the configuration of it to the driver itself.
Unlike Linux, where the PCS/PMA PHY is managed by phylink, managing the
PCS/PMA PHY is only internal to the driver in U-Boot. The PCS/PMA PHY
pressents only when the phy-mode is configured as SGMII or 1000Base-X,
so it is always 1 Gbps and full-duplex and we may skip passing link
information out.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Link: https://lore.kernel.org/r/20221101035800.912644-2-andy.chiu@sifive.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The TI sysc bus driver is required to allow access to the SPI bus on
am335x platforms. To support SPI boot this driver needs to be enabled in
the SPL/TPL as appropriate.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
We should only perform additional iteration steps when needed to
initialize the parent of a device. Other binding errors (such as a
missing driver) should not lead to additional iteration steps.
Unnecessary iteration steps can cause issues when memory is tightly
constrained (such as in the TPL/SPL) since device_bind_by_name()
unconditionally allocates memory for a struct udevice. On the SanCloud
BBE this led to boot failure caused by memory exhaustion in the SPL
when booting from SPI flash.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Add a driver for the Intel XWAY GbE PHY:
- configure RGMII using dt phy-mode and standard delay properties
- use genphy_config
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The rx descriptor list is in cached memory, and there may be multiple
descriptors per cache-line. After reclaim_rx_buffers marks a descriptor
as unused it does a cache flush, which causes the entire cache-line to
be written to memory, which may override other descriptors in the same
cache-line that the controller may have written to.
The fix skips freeing descriptors that are not the last in a cache-line,
and if the freed descriptor is the last one in a cache-line, it marks
all the descriptors in the cache-line as unused.
This is similarly to what is done in drivers/net/fec_mxc.c
In my case this bug caused tftpboot to fail some times when other
packets are sent to u-boot in addition to the ongoing tftp (e.g. ping).
The driver would stop receiving new packets because it is waiting
on a descriptor that is marked unused, when in reality the descriptor
contains a new unprocessed packet but while freeing the previous buffer
descriptor & flushing the cache, the driver accidentally marked the
descriptor as unused.
Signed-off-by: Yaron Micher <yaronm@hailo.ai>
Fix a couple of typos:
- s/Acquantia/Aquantia/
- s/firmare/firmware/
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add new desc_per_cacheline property which lets a platform run RX descriptor
cleanup after every power-of-2 - 1 received packets instead of every packet.
This is useful on platforms where (axi_bus_width EQOS_AXI_WIDTH_n * DMA DSL
inter-descriptor word skip count + DMA descriptor size) is less than cache
line size, which necessitates packing multiple DMA descriptors into single
cache line.
In case of TX descriptors, this is not a problem, since the driver always
does synchronous TX, i.e. the TX descriptor is always written, flushed and
polled for completion in eqos_send().
In case of RX descriptors, it is necessary to update their status in bulk,
i.e. after the entire cache line worth of RX descriptors has been used up
to receive data.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Separate TX and RX DMA rings to make their handling slightly clearer.
This is a preparatory patch for bulk RX descriptor flushing.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
LiteX is a soft system-on-chip that targets FPGAs. LiteETH is a basic
network device that is commonly used in LiteX designs.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Drop support for quickly deprecated DT property "snps,ref-clock-period-ns"
to prevent its proliferation.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
GUCTL.REFCLKPER can only account for clock frequencies with integer
periods. To address this, program REFCLK_FLADJ with the relative error
caused by period truncation. The formula given in the register reference
has been rearranged to allow calculation based on rate (instead of
period), and to allow for fixed-point arithmetic.
Additionally, calculate a value for 240MHZDECR. This configures a
simulated 240Mhz clock using a counter with one fractional bit (PLS1).
This register is programmed only for versions >= 2.50a, since this is
the check also used by commit db2be4e9e30c ("usb: dwc3: Add frame length
adjustment quirk").
[ marek: Ported from Linux kernel commit
596c87856e08d ("usb: dwc3: Program GFLADJ") ]
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Marek Vasut <marex@denx.de> # Port from Linux
Instead of using a special property to determine the reference clock
period, use the rate of the reference clock. When we have a legacy
snps,ref-clock-period-ns property and no reference clock, use it
instead. Fractional clocks are not currently supported, and will be
dealt with in the next commit.
[ marek: Ported from Linux kernel commit
5114c3ee24875 ("usb: dwc3: Calculate REFCLKPER based on reference clock") ]
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Marek Vasut <marex@denx.de> # Port from Linux
Set reference clock period when it differs from dwc3 default hardware
set.
We could calculate clock period based on reference clock frequency. But
this information is not always available. This is the case of PCI bus
attached USB host. For that reason we use a custom property.
Tested (USB2 only) on IPQ6010 SoC based board with 24 MHz reference
clock while hardware default is 19.2 MHz.
[ baruch: rewrite commit message; drop GFLADJ code; remove 'quirk-' from
property name; mention tested hardware ]
[ marek: Ported from Linux kernel commit
7bee318838890 ("usb: dwc3: reference clock period configuration") ]
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Balaji Prakash J <bjagadee@codeaurora.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Marek Vasut <marex@denx.de> # Port from Linux
Cache ref_clk clock pointer in struct dwc3 . This is a preparatory
patch for subsequent backports from Linux kernel which configure
GFLADJ register content based on the ref_clk rate and therefore need
access to the ref_clk pointer.
It is possible to extract the clock pointer from existing clk_bulk
list of already claimed clock, no need to call clk_get*() again.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The "generic_bus_%x_dev_%x" string which is printed into this buffer
can be up to 34 characters long ("generic_bus_12345678_dev_12345678").
The buffer would be clipped by snprintf() if both %x were at maximum
range. Make sure the buffer is long enough to cover such possibility.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use macro to represent the RL and WL setting to ensure the PHY and
controller setting are aligned.
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Adjust the following settings to get better timing and signal quality.
1. write DQS/DQ delay
- 1e6e2304[0]
- 1e6e2304[15:8]
2. read DQS/DQ delay
- 0x1e6e0298[0]
- 0x1e6e0298[15:8]
3. CLK/CA timing
- 0x1e6e01a8[31]
4. Read and write termination
- change RTT_ROM from 40 ohm to 48 ohm (MR1[10:8])
- change RTT_PARK from disable to 48 ohm (MR5[8:6])
- change RTT_WR from 120 ohm to disable (MR2[11:9])
- change PHY ODT from 40 ohm to 80 ohm (0x1e6e0130[10:8])
Note1: Both DDR-PHY and DDR controller have their own registers for DDR4
Mode Registers (MR0~MR6). This patch introduces macros to synchronize
the MR value on both sides.
Note2: the waveform meansurement can be found in item #21 of Aspeed
AST26x0 Application note (AP note).
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
The condition "~data" in the if-statement is a typo. The original
intention is to poll if SDRAM_PHYCTRL0_INIT bit equals to 0. So use
"data == 0" for instead.
Besides, the bit[1] of "phy_status" register is hardwired to
SDRAM_PHYCTRL0_INIT (with inverse logic). Since SDRAM_PHYCTRL0_INIT has
already done, remove the unnecessary checking of phy_status[1].
Fixes: fde9314346 ("ram: aspeed: Add AST2600 DRAM control support")
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
- Re-add the old PHY reset binding for nanopi-k2
-----BEGIN PGP SIGNATURE-----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=yEaP
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20221122' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Implement setbrg op to meson serial device
- Re-add the old PHY reset binding for nanopi-k2
Invoking lseek() may result in an error. Handle it.
Addresses-Coverity-ID: 376212 ("Error handling issues (CHECKED_RETURN)")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Implement setbrg in amlogic/meson serial device with driver model
similar to how the meson_uart.c driver does it in Linux. Also
configure (probe) the serial device with the new reg5 register.
Signed-off-by: Edoardo Tomelleri <e.tomell@gmail.com>
Link: https://lore.kernel.org/r/20220918161701.572814-1-e.tomell@gmail.com
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
When cadence_qspi_versal_flash_reset() function is called in mini
u-boot where there is no firmware support, it is missing defines for
macro's BOOT_MODE_POR_0 & BOOT_MODE_POR_1. Remove them and replace with
already define macro's which have same values as these.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
