Sync the sdmmc node from linux-next, include required nodes in SPL and
imply Kconfig options required for functional sdmmc clk in SPL and
U-Boot proper.
This make it possible for both SPL and U-Boot proper to configure sdmmc
clocks. In SPL, before TF-A is loaded, scru regs is configured, in
U-Boot proper a SCMI message is sent to TF-A.
Fixes: 95c8656b72 ("ARM: dts: rockchip: rk3588s-u-boot: Add sdmmc node")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Booting from sdmmc on RK3588 currently works because of a workaround in
the device tree, clocks are reordered so that the driver use ciu-sample
instead of ciu, and the BootRom initializes sdmmc clocks before SPL is
loaded into DRAM.
The sdmmc clocks are normally controlled by TF-A using SCMI. However,
there is a need to control these clocks in SPL, before TF-A has started.
This adds a rk3588_scru driver to control the sdmmc clocks in SPL before
TF-A has started, using scru regs. It also adds a small glue driver to
bind the scmi clock node to the rk3588_scru driver in SPL.
Fixes: 7a474df740 ("clk: rockchip: Add rk3588 clk support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add fdtoverlay_addr_r, kernel_comp_addr_r and imply use of
OF_LIBFDT_OVERLAY on RK3568 and RK3588 to support fdtoverlay
and kernel compression.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
The TF-A blobs used to boot RK3568 and RK3588 boards is based on atf
v2.3. Mainline atf v2.3 contains an issue that could lead to a crash
when it fails to parse the fdt blob being passed as the platform param.
An issue that was fixed in atf v2.4.
The vendor TF-A seem to suffer from a similar issue, and this prevents
booting when fdt blob is large enough to trigger this condition.
Fix this by implying SPL_ATF_NO_PLATFORM_PARAM to let u-boot pass a
NULL pointer instead of the fdt blob as the platform param.
This fixes booting Radxa ROCK 3A after recent sync of device tree.
Fixes: 073d911ae6 ("rockchip: rk3568-rock-3a: Sync device tree from linux")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Running U-Boot from a SD-card on ROCK 5 Model B fails to load atf using
DMA and prints debug_uart messages.
<debug_uart>
<debug_uart>
U-Boot SPL 2023.04-rc3 (Mar 12 2023 - 00:30:16 +0000)
Trying to boot from MMC1
## Checking hash(es) for config config-1 ... OK
## Checking hash(es) for Image atf-1 ... sha256 error!
Bad hash value for 'hash' hash node in 'atf-1' image node
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Use fifo-mode to disable DMA in SPL, add same-as-spl to boot-order and
remove DEBUG_UART_ANNOUNCE option to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
misc_read() is documented to return the number of bytes read or a
negative error value. The Rockchip drivers currently do not implement
this correctly and instead return zero on success or a negative error
value.
In preparation for fixing the drivers, fix the condition here to only
error on negative values.
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3066/rk3188 DT files from Linux.
This is the state as of linux-next v6.2-rc4.
New nfc node for MK808 rk3066a.
CRU nodes now have a clock property.
To prefend dtoc errors a fixed clock must also be
included for tpl/spl in the rk3xxx-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The gpio node names are made generic, but without
gpio bank ID. Add gpio-ranges to rk3188-u-boot.dtsi
for now till a better method is found.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The gpio node names are made generic, but without
gpio bank ID. Add gpio-ranges to rk3066a-u-boot.dtsi
for now till a better method is found.
Disable gpio6 as the driver gives an error code
on return as status.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi
version 6.3 -rc2 with the U-Boot version partial
sync the pwm nodes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi
version 6.3 -rc2 with the U-Boot version partial
sync the vop/lvds/mipi/hdmi nodes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3288 edp node has a phy node in Linux with a clock
property while current U-Boot driver expects this clock
on position index 1. Move U-Boot-specific DT clock properties
to rk3288-u-boot.dtsi and partially sync the edp node.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi
version 6.3 -rc2 with the U-Boot version partial
sync the grf and pmu nodes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi version
with the U-Boot version move the io-domains nodes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ft_board_setup() should be availble for use in board files but using it
in the rk3288 machine file blocks this functionality.
ft_system_setup() is the more appropriate function to use in a machine
definition.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There is no support to initialize DRAM on RK3588 SoCs using U-Boot TPL
and instead an external TPL binary must be used to generate a bootable
u-boot-rockchip.bin image.
Enable ROCKCHIP_EXTERNAL_TPL by default for RK3588, add build steps for
RK3588 to documentation and clean up CONFIG_BINMAN_FDT options.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Jagan Teki <jagan@edgeble.ai>
rk3588 evb1 v10 is a evalution board from Rockchip, it is a dev board for
rockchip and also a reference board for board vendors.
Hardware:
SoC: RK3588
DRAM: LPDDR4X 8GB
Debug: UART2 via USB
PCIe: 3x4 *1
SATA *2
HDMI out *2
HDMI IN *1
USB2.0 Host *2
USB3.0 Host *1
Type C *1
MIPI DSI panel
dts Sync from Linux v6.2.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@edgeble.ai>
Some sections in the linker scripts are aligned to 4 bytes, which
may cause misaligned exception on some platforms, e.g.: clearing
the bss section on 64-bit hardware if __bss_start does not start
from a naturally 8 bytes aligned address.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
U-Boot SPL is not relocable. Drop these relocation sections.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
board_init_r does not return for U-Boot SPL hence there is no need
to update the link register when jumping to board_init_r.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The codes currently skip the very first relocation entry, and have
an inaccurate comment "skip first reserved entry" indicating that
the first entry is reserved, but later it references the elements
in the first relocation entry using a minus offset.
Change to use a positive offset so that there is no need to skip
the first relocation entry.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
't5' already contains relocation type so don't bother reloading it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
The __bss_start is the source end address hence load its address
directly into register 't2' for optimization.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
Since commit 409e4b5478 ("Makefile: Enforce DWARF4 output") the
whole U-Boot build switched to enforce DWARF4 output, but RISC-V
is still on its own setting. Let's switch to use U-Boot's setting.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add initial u-boot device tree for the JH7110 RISC-V SoC.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Add initial device tree for the JH7110 RISC-V SoC.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Add board support for StarFive VisionFive v2.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Add Kconfig to select the basic functions for StarFive JH7110 SoC.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Add StarFive JH7110 SoC to support RISC-V arch.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
In all these cases, the index on the LHS is immediately afterwards
used to access the array appearing in the ARRAY_SIZE() on the RHS - so
if that index is equal to the array size, we'll access
one-past-the-end of the array.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add QSPI support on STM32MP13x SoC family
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
- Spring Cleanup of Amlogic board documentation
- add support for BananaPi M2-Pro
- add support for BananaPi M2S
- add support for Radxa Zero2
- add support for WeTek Hub and WeTek Play2
- switch LibreTech-CC v2 and WeTek Core2 to EE powerdomain
- add support for Beelink GT1 Ultimate
-----BEGIN PGP SIGNATURE-----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=Vf7Q
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20230417' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Add initial support for BPI-CM4
- Spring Cleanup of Amlogic board documentation
- add support for BananaPi M2-Pro
- add support for BananaPi M2S
- add support for Radxa Zero2
- add support for WeTek Hub and WeTek Play2
- switch LibreTech-CC v2 and WeTek Core2 to EE powerdomain
- add support for Beelink GT1 Ultimate
Import the dts files from linux-amlogic/for-next (Linux 6.4-rc1) and
add the old PHY reset bindings for dwmac to the u-boot.dtsi until we
support the new bindings in the PHY node. Without this the PHY is not
functional in u-boot or Linux.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-13-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Import the device-tree from linux-amlogic/for-next (Linux 6.4-rc1)
to support the Radxa-Zero2 board.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-10-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Import the device-tree from linux-amlogic/for-next (Linux 6.4-rc1)
and omit the NPU node from the A311D board variant dts as this is
not supported under U-Boot.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-7-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Import the board dts from the linux-amlogic/for-next (6.4-rc1)
branch. This involves spliting the BPI-M5 dts into a dtsi and
then reusing this for the M2-Pro.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230323143142.780306-4-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add support for both the BananaPi BPI-CM4 module and the BananaPi
baseboard which is compatible with the RaspberryPi CM4IO baseboard.
The BananaPi BPI-CM4 module follows the CM4 specifications at [1],
but with a single HDMI port and a single DSI output.
The current CM4IO baseboard DT should work fine on the Raspberry CM4
baseboard and other derivatives baseboards, but proper DT should
be written for other baseboards.
[1] https://datasheets.raspberrypi.com/cm4io/cm4io-datasheet.pdf
Link: https://lore.kernel.org/r/20230307-u-boot-cm4-v1-2-43f5a393cd37@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The QEMU emulation of m68k does not support RAMBAR accesses,
add Kconfig option which inhibits those accesses, so that
U-Boot can be started in m68k QEMU for CI testing purpopses
until QEMU emulation improves.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The QEMU emulation of m68k does not support DMA timer, the only
timer that is supported is the PIT timer. Implement trivial PIT
timer support for m68k.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
There is an existing CONFIG_MCFTMR Kconfig symbol,
use it and drop all other instances of CFG_MCFTMR.
This duality is likely a result of bogus conversion
to Kconfig.
Fixes: 7ff7b46e6c ("m68k: rename CONFIG_MCFTMR to CFG_MCFTMR")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add a new config option CONFIG_MVEBU_SPL_SATA_BLKSZ for specifying block
size of SATA disk. This information is used during building of SATA
kwbimage and must be correctly set, otherwise BootROM does not load SPL.
For 4K Native disks CONFIG_MVEBU_SPL_SATA_BLKSZ must be set to 4096.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Find SATA block device by blk_get_devnum_by_uclass_id() function and read
from it the real block size of the SATA disk.
Signed-off-by: Pali Rohár <pali@kernel.org>
Some SoCs of the H616 family use a die variant, that puts some CPU power
and reset control registers at a different address. There are examples
of two instances of the same board, using different die revisions of the
otherwise same H313 SoC. We need to write to a register in that block
*very* early in the SPL boot, to switch the core to AArch64.
Since the devices are otherwise indistinguishable, let the SPL code read
that die variant and use the respective RVBAR address based on that.
That is a bit tricky, since we need to do that in hand-coded AArch32
machine language, shared by all 64-bit SoCs. To avoid build dependencies
in this mess, we always provide two addresses to choose from, and just
give identical values for all other SoCs. This allows the same code to
run on all 64-bit SoCs, and controls this switch behaviour purely from
Kconfig.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
