arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
-----BEGIN PGP SIGNATURE-----
iFsEABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX/ROlgAKCRDKSWXLKUoM
IRC5AIkBzg4Sz8fQgdCiOK89k7tdFKMAnA9SYhgm4TSCzffZCJwnm78QoGAC
=4FnY
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.04
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Since GPIO_ACTIVE_HIGH is defined as 0, this change only increases the
correctness of the DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Due to a change in gpiolib-of.c, setting flags to GPIO_ACTIVE_LOW and
using output-low DT property leads to the GPIO being set high instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
In the spirit of using the same base name for all of these related macros,
rename this to have the operation at the end. This is not widely used so
the impact is fairly small.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current macro is a misnomer since it does not declare a device
directly. Instead, it declares driver_info record which U-Boot uses at
runtime to create a device.
The distinction seems somewhat minor most of the time, but is becomes
quite confusing when we actually want to declare a device, with
of-platdata. We are left trying to distinguish between a device which
isn't actually device, and a device that is (perhaps an 'instance'?)
It seems better to rename this macro to describe what it actually is. The
macros is not widely used, since boards should use devicetree to declare
devices.
Rename it to U_BOOT_DRVINFO(), which indicates clearly that this is
declaring a new driver_info record, not a device.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
This uses up space in the SPL binary but it always starts as zero. Also
some boards cannot support data in TPL (e.g. Intel Apollo Lake).
Use malloc() to allocate this structure instead, by moving the init a
little later, after malloc() is inited. Make this function optional since
it pulls in malloc().
This reduces the TPL binary size on coral by about 64 bytes
Signed-off-by: Simon Glass <sjg@chromium.org>
Lower case should be used for function names. Update this driver and its
callers accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Typedefs should not be used in U-Boot and structs should be lower case.
Update the code to use struct ns16550 consistently.
Put a header guard on the file while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This patch add ethernet node gem1 to zcu1285 RevB.
GMII to RGMII converter sits between MAC and external
phy connected over GMII to MAC and RGMMI to external phy
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch add ethernet node gem1 to zcu1275 RevB.
GMII to RGMII converter sits between MAC and external
phy connected over GMII to MAC and RGMMI to external phy.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On the qemu arm platform, the virtio devices are initialised in the
board_init function, which gets called before the initr_pci. With
this sequence, the virtio block devices on the pci bus are not
initialised. Move the initialisation of the virtio devices to
board_late_init which gets called after the call to initr_pci.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
For correct spi bus detection the spi0 alias is needed in the DT.
Otherwise this error will ocurr in U-Boot:
Invalid bus 0 (err=-19)
Failed to initialize SPI flash at 0:0 (error -19)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dennis Gilmore <dgilmore@redhat.com>
Tested-by: Dennis Gilmore <dgilmore@redhat.com>
Add some missing "u-boot,dm-pre-reloc;" properties to UART0, SPI
controller and SPI NOR flash node to enable usage in SPL. Otherwise
these devices will not be available.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dennis Gilmore <dgilmore@redhat.com>
Tested-by: Dennis Gilmore <dgilmore@redhat.com>
Use %u and not %d for unsigned values.
Print kHz and not khz.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The dart6ul has an i2c eeprom at 0x50 which contains, among other
things, the manufacturing/revision/options info of the SoM. This patch
replaces the current checkboard() implementation with a more
exhaustive one based on the content of the eeprom.
Since this code uses the new driver model, some changes were also
required in the DTS to make the nodes related to i2c available before
relocation.
This code was inspired from the supported u-boot code from Variscite
which can be found here:
https://github.com/varigit/uboot-imx/tree/imx_v2018.03_4.14.78_1.0.0_ga_var02
New output example:
Board: PN: VSM-6UL-705B, Assy: AS1812142257, Date: 2019 Feb 17
Storage: eMMC, Wifi: yes, DDR: 1024 MiB, Rev: 2.4G
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The eeprom at address 0x50 is a BR24G04NUX-3TTR. It has a
4Kbit (512x8) capacity, change the compatible string to reflect this
fact.
Also, add an alias to easily refer to this eeprom with
fdt_path_offset() which will be in another commit.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Calling ahab_close cmd force the user to interact for confirmation.
This is not user-friendly when using this cmd during factory process.
Allow the user to pass '-y' option to bypass this confirmation.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Oliver Graute <oliver.graute@kococonnector.com>
The current PHY rework does the following things:
1. Configure 125MHz clock
2. Setup the TX clock delay (RX is enabled by default),
3. Setup reserved bits to avoid voltage peak
The clock delays are nowadays already configured by the
PHY driver (in ar803x_delay_config). The code for that
can simply be dropped. The clock speed can also be
configured by the PHY driver by adding the device tree
property "qca,clk-out-frequency".
What is left is setting up the undocumented reserved bits
to avoid the voltage peak problem. I slightly improved its
documentation while updating the board's PHY rework code.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
i.MX8M series provide support for high speed grades in their
usdhc controllers, which has eMMC and SDHC connected to them.
Enable this support across the entire i.MX8M family by providing quirks
to usdhc controllers designated by storage media connected to them.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Some SD Card controller and power circuitry has increased capacitance,
which keeps the internal logic remains powered after regulator is switch
off. This is generally the case when card is switched to SD104 mode,
where a power cycle should be performed. In case if the card internal
logic remains powered, it causes a subsequent failure of mode
transition, effectively leading to failed enumeration.
Introduce a delay of 20 msec in order to provide a possibility for
internal card circuitry to drain voltages and perform a power cycle
correctly.
Similar fix is done in commit c49d0ac38a ("ARM: dts: rmobile: Increase
off-on delay on the SD Vcc regulator") targeted Renesas SOCs.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
There have been some updates to the device tree since 5.6.
This also includes some clocks, and makes it easier to keep
board device tree files in sync with Linux
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Fixed wrong PHY Interface Mode
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode)
the correct phy-mode should be "rgmii-id", so fix it accordingly
to fix the Ethernet regression.
This problem has been exposed by commit:
commit 13114f38e2
Fix the phy-mode accordingly to fix the regression.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Since linux commit 2e6cde96873253fd9eb0f20afd8ffd18278cff75 ("arm64:
dts: ls1028a: make the eMMC and SD card controllers use fixed indices")
mmc0 is the eMMC and mmc1 is the SD card. Also swap it in u-boot to
avoid any confusion by the user and to be aligned with linux.
Signed-off-by: Michael Walle <michael@walle.cc>
Now that there is only one sequence number (rather than both requested and
assigned ones) we can simplify this function. Also update its caller to
simplify the logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
For the proper reboot Odroid-C4 board requires to switch TFLASH_VDD_EN
pin to the high impedance mode, otherwise the board is stuck in the
middle of loading early stages of the bootloader from SD card.
This can be achieved by using the OPEN_DRAIN flag instead if the
ACTIVE_HIGH, what will leave the pin in input to achieve high state (pin
has the pull-up) and solve the issue.
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds SoC-specific compatible strings to all users of the designware
spi device. This will allow for the correct driver to be selected for each
device. Where it is publicly documented, a compatible string for the
specific device version has also been added. Devices without
publicly-documented device versions include MSCC SoCs, and Arc Socs. All
compatible strings except those for SoCFPGAs and some of the versioned
strings have been taken from Linux.
Since SSI_MAX_XFER_SIZE is determined at runtime, this is not strictly
necessary. However, it is a good cleanup and brings things closer to Linux.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl/TlVUcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyK8eB/9mIJCgCiDue2ytkUg+
fyJHHtHf+rFIbvLiR+iVy/2rXlsjfXwNVyJTswJOCucit0cf+F7fh6vi/AnOoDnE
Zezj9ngm+25fvffQjt0T74V2w+GhT5OXqR7ctpIcrmKun2UTujSA9NQqRaLFDI9x
RQlUXsCzLypFZRXvyOCo34Nz7MZ1QvIAKxEJyYb7ft/qnbtILDr0p54xxjlK5B/W
s+MP05qaRmup9rk33JwfLmeyjTmDBuri0rBh/2XKFtszJBm5CdgXJEqNY+22JzJF
xlqfobmdPn77+JH36B/KJgDmrrL05vv+RyvOPoBNzm6BEKtlflcSf9NnTKlSud4y
w/50
=r687
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2021.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel fixes for 2021.01 cycle
This set includes very important fixes for: MMC booting on several
boards, drive strength on sam9x60ek mmc lines, compile issues for
timer.c old driver, removal of unwanted access to sam9x60 bit for
oscillator bypass mode, and eeproms read on sama5d2_icp.
The correct compatible for this eeproms is microchip,24aa02e48
The previous compatible string was working up to U-boot 2020.04.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
The USB support is not by default enabled on all designs, so it does not
make seance to have USB specific erratum's enabled on such a designs.
On our internal Hitachi-Powergrids design not using the USB controller
there is a crash when accessing those specific memory locations selected
by the erratum flags.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When booting from TF-A there is a logic that attempt to detect if the
default environment is used, if this is the case it then set the
`bootcmd` and `mcinitcmd` depending of the device we booted from.
This detection logic is dubious as it access internals of the env
implementation and it doesn't always work correctly.
First of all it detect any valid environment as not being the
default, so after running `env default -a && saveenv` the board
doesn't boot anymore as `bootcmd` is then empty.
But it also fails in some other ways, for example it always detect a
default environment when redundant env is enabled on MMC, so in that
case `bootcmd` is overwritten on every boot.
Instead of increasing the complexity of the detection just check if
`bootcmd` and `mcinitcmd` are set in the environment and set them if
they are not.
Signed-off-by: Alban Bedel <alban.bedel@aerq.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Check for NULL return value from fdt_getprop() in
fdt_fixup_remove_jr()
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
[Fixed checkpatch errors/warnings]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[Fixed whitespace errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/Q5aAACgkQ4rK92eCq
k3XuqAgAifJcb3NxKmWa4eFDbZpWZ1R8h6FPp6vlmvyC4C3otRHEe5WrYCsAeqy1
Gs311dtdluc4y5Ltmf54OcN7ICfLsSiOvye85f5myhPj1v4d1F1Z70X0FDo/o9hE
7TEZfWBQtNjXI4F23+vaDT4jCvUZV1LR6Lab/zLLw1/uLUxxS799kcFiWgHLuEoH
8Cv0JbgzLuuVk5lyLJ+DFZOcntwWu5+Qm+l5eS46armbKphMFh5KPJ9PG81eJE3N
zsCpavEs4nuQl7wGF8HPfDWxz5Xef6ip3A4Owh92t3WQWKxp1bSUKqDeKZTkhIyS
LSJKe9CQ9+zCS3m3Utoi1pVt1EbFrQ==
=cgbE
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201209' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
Add USB OTG ID pin mux and switch the USB OTG port
from peripheral to OTG mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The DH DRC02 board has an on-board microSD slot,
add DT properties to enable the slot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter
or without one on the SDMMC1 interface. Because the SDMMC1 interface is
limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback
clock to permit operation of the same U-Boot image on both SoM with and
without voltage level shifter.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The default state of SD bus and clock line is logical HI. SD card IO is
open-drain and pulls the bus lines LO. Always enable the SD bus pull ups
to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus
voltage level shifter, the pull ups are built into the level shifter,
however that has no negative impact.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
- Espressobin: Simplify DT handling of board variants (Pali)
- Add Luka Perkov to maintainers of Puzzle-M801 (Luka)
- Armada 38x: Enable board specific USB2 high-speed impedance
threshold configuration (Joshua)
To simplify setup, configuration and compilation of u-boot, define emmc
node for all Espressobin boards. Espressobin boards without populated emmc
works correctly, just detection and initialization of emmc obviously fails.
Code for emmc is extracted from commit f1a43c84a9 ("arm64: dts: a3720:
add support for espressobin with populated emmc").
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Gérald Kerma <gerald@gk2.net>
Hardware testing of a board using the Armada 385 has shown that an
impedance threshold setting of 0x7 performs better in an eye-diagram
test than with Marvell's recommended value 0x6.
As other boards may still perform better with Marvell's reccomended value,
a configuration option is added with a default value of 0x6.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
Introduce weak function board_mem_get_layout() which allows overriding
the memory layout from board code in runtime, useful for handling
different SKU versions.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This commit adds initial support for the Toradex Apalis iMX8X 2GB WB
IT V1.1A System on Module support [1].
Boot log:
U-Boot 2020.10-02940-g894aebb7e8-dirty (Oct 22 2020 - 09:43:57 +0300)
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial@5a070000
Out: serial@5a070000
Err: serial@5a070000
Model: Toradex Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT V1.1A,
Serial# 06617018
Net: eth0: ethernet@5b040000 [PRIME]
Hit any key to stop autoboot: 0
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet (*)
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
* With the SCU FW from the latest Toradex BSP 5.0.0 (SCU FW 1.5.1)
ETH PHY encounters bring up problems after reset, this will be fixed
soon on SCU FW side.
[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8x
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Introduce initial hierarchy of device trees for Apalis iMX8X
System on Module.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
the mem_map structure containing the size of SDRAM is used in various
cache functions in cache_v8.c thus we need to update it with the
sdram size the board is configured with as well. Without this
the cache functions do not get setup properly and can hang
in the case where a board reports more SDRAM than defined in
PHYS_SDRAM_SIZE.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The used PMIC has been changed from RHOM BD71837 to NXP PCA9450A.
Adjust the device tree accordingly.
Remove the old ADC node as the ADC has been changed and has no longer
a separate power rail.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reduce vital product data size to match the latest specification.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following warning:
arch/arm/mach-imx/imx8/ahab.c:105:3: warning: implicit declaration of function ‘flush_dcache_range’ [-Wimplicit-function-declaration]
flush_dcache_range(s, e);
^~~~~~~~~~~~~~~~~~
Include cpu_func.h header which declares the flush_dcache_range()
function.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
arch/arm/mach-imx/imx8/ahab.c: In function ‘authenticate_os_container’:
arch/arm/mach-imx/imx8/ahab.c:96:9: warning: format ‘%x’ expects argument of type
‘unsigned int’, but argument 9 has type ‘ulong {aka long unsigned int}’ [-Wformat=]
debug("img %d, dst 0x%x, src 0x%x, size 0x%x\n",
Fix those by using "%lu" specified.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
arch/arm/mach-imx/imx8/ahab.c:110:63: warning: format ‘%x’ expects
argument of type ‘unsigned int’, but argument 2 has type ‘u64 {aka long
long unsigned int}’ [-Wformat=]
Fix those by using %llx
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Removed aristainetos2, 2b, 2b-csl. This boards have been
recalled and destroyed.
Adapt board code to remove stuff not needed anymore.
Fix checkpatch warning, remove fdt_high and initrd_high
from default environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
zu remove
The BL31 expects the GIC to be uninitialized. Thus, if we are loading
the BL31 by the SPL we must not initialize it. If u-boot is loaded by
the SPL directly, it will initialize the GIC again (in the same
lowlevel_init()).
This was tested on a custom board with SPL loading the BL31 and jumping
to u-boot as BL33 as well as loading u-boot directly by the SPL. In case
the ATF BL1/BL2 is used, this patch won't change anything, because no
SPL is used at all.
Signed-off-by: Michael Walle <michael@walle.cc>
There is SPL_ARMV8_SEC_FIRMWARE_SUPPORT and ARMV8_SEC_FIRMWARE_SUPPORT.
Thus use CONFIG_IS_ENABLED() instead of the simple #ifdef.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Activate ARCH_SUPPORT_PSCI as other TEGRA124 target and remove
CONFIG_ARMV7_PSCI and CONFIG_ARMV7_PSCI_NR_CPUS in configs file as they
are migrated in Kconfig.
Select CONFIG_ARMV7_PSCI_0_1 (the first PSCI version),
because CONFIG_ARMV7_PSCI_0_2 and CONFIG_ARMV7_PSCI_1_0
are not activated in this product.
Hi,
This patch depend on the previous serie [1].
I don't test this patch on real hardware but
after this patch the size of the binary don't change.
In .config we have:
CONFIG_ARCH_SUPPORT_PSCI=y
CONFIG_ARMV7_PSCI=y
# CONFIG_ARMV7_PSCI_1_0 is not set
# CONFIG_ARMV7_PSCI_0_2 is not set
CONFIG_ARMV7_PSCI_0_1=y
CONFIG_ARMV7_PSCI_NR_CPUS=4
In u-boot.cfg, this patch only add the 2 lines
#define CONFIG_ARCH_SUPPORT_PSCI 1
#define CONFIG_ARMV7_PSCI_0_1 1
[1] "Convert CONFIG_ARMV7_PSCI_1_0 and CONFIG_ARMV7_PSCI_0_2 to Kconfig"
http://patchwork.ozlabs.org/project/uboot/list/?series=184029
Regards
Patrick
END
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Peter Chubb <peter.chubb@data61.csiro.au>
Signed-off-by: Tom Warren <twarren@nvidia.com>
USB clocks were completely forgotten as driver would always return 0 even if clock ID was unknown.
This behaviour changed with "IPQ40xx: clk: dont always return 0" and this will now causes the USB-s to fail probing as clock enable will return -EINVAL.
So to fix that lets add all of the USB clocks to the driver.
Fixes: 430e1dcf ("IPQ40xx: Add USB nodes")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Currently the driver will go through the clock ID-s and set/enable them as needed.
But if the ID is unknown it will fall through the switch case to the default case which will always return 0.
This is not correct and default cases should return a error code since clock ID is unknown.
So lets return -EINVAL instead.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
There is no point in having break statements in the switch case as there is already a return before break.
So lets drop them from the driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Lets convert the driver to use dev_read_addr() instead of the devfdt_get_addr().
While we are here, lets also alphabetise the includes.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The AT91 architecture now has two possible timer blocks, the old PIT timer
and the new PIT64B.
The timer.c file has an old non DM driver that works for platforms
that do not use the ATMEL_PIT_TIMER DM-based driver.
Update the Makefile to select this old driver in case neither of the
ATMEL_PIT_TIMER and the MCHP_PIT64B_TIMER are selected.
Suggested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
SAMA7G5 uses CCF driver under drivers/clk/at91/ and not the custom older
at91 clock.c driver. Remove it from the compilation list and adapt cpu.c
arch_cpu_init() to avoid calling at91_clock_init() which is wrong
anyway.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Align the pin setup for sdhci0 with linux kernel.
This means to have slew rate enable and high drive strength.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Use the reset function to handle the hold boot bit in RCC
with device tree handle with MCU_HOLD_BOOT identifier.
This generic reset allows to remove the two specific properties:
- st,syscfg-holdboot
- st,syscfg-tz
This patch prepares alignment with kernel device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Fabien DESSENNE <fabien.dessenne@st.com>
Cc: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
spl_mmc_boot_partition is only defined when
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION is defined.
Signed-off-by: Richard Genoud <richard.genoud@posteo.net>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The QSPI CS2 is not used on DHCOM, remove the pinmux and flash@1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The uSD slot card-detect GPIO is connected to PG1, fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add DT for DH PicoITX unit, which is a bare-bones carrier board for
the DHCOM. The board has ethernet port, USB, CAN, LEDs and a custom
board-to-board expansion connector.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Correct the ALIGN macro usage in mmu_set_region_dcache_behaviour
call: the address must use ALIGN_DOWN and size can use ALIGN macro.
With STM32_SYSRAM_BASE=0x2FFC0000 and MMU_SECTION_SIZE=0x100000 for
STM32MP15x the computed address was 30000000 instead of 2ff00000.
Fixes: 43fe9d2fda ("stm32mp1: mmu_set_region_dcache_behaviour")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Commit 4b2be78ab6 ("time: Fix get_ticks being non-monotonic")
puts in evidence that get_ticks is called before timer initialization.
Fix it by initializing timer before relocation.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Device tree alignment with kernel v5.10-rc1.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Since kernel v4.8-rc1, commit 05b23ebc2bd9 ("ARM: dts: armv7-m: remove skeleton.dtsi include"),
skeleton.dtsi file is no more included.
This synchronization is needed to avoid to get 2 memory node
in DTB file if, in DTS file, memory node is declared with the correct
syntax as following:
memory@90000000 {
device_type = "memory";
reg = <0x90000000 0x800000>;
};
Then in DTB, we will have the 2 memory nodes, which is incorrect and
cause misbehavior during DT parsing by U-boot:
memory {
device_type = "memory";
reg = <0x00 0x00>;
};
memory@90000000 {
device_type = "memory";
reg = <0x90000000 0x800000>;
};
Issue found when synchronizing MCU's STM32 DT from kernel v5.10-rc1.
When using fdtdec_setup_mem_size_base() or fdtdec_setup_memory_banksize()
API, first above memory node is found (with reg = <0x00 0x00>), so
gd->ram_size, gd->ram_base, gd->bd->bi_dram[bank].start and
gd->bd->bi_dram[bank].size are all set to 0 which avoid boards to boot.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Renesas RZ/G2H (r8a774e1) is pin compatible with R-Car H3 (r8a77951),
however it doesn't have several automotive specific peripherals. Add
a r8a77951 specific pin groups/functions along with common pin
groups/functions for supporting both r8a77951 and r8a774e1 SoC.
PFC changes are synced from mainline linux-5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Renesas RZ/G2N (r8a774b1) is pin compatible with R-Car M3-N (r8a77965),
however it doesn't have several automotive specific peripherals. Add
a r8a77965 specific pin groups/functions along with common pin
groups/functions for supporting both r8a77965 and r8a774b1 SoC.
PFC changes are synced from mainline linux-5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
There is no reason to have these macros. But record offsets of missing
register in the structure for future use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit imports device tree files that are related to Allwinner V3
series from Linux commit 3650b228f83a ("Linux 5.10-rc1").
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The reference design of Allwinner V3 series uses an
AXP203 or AXP209 PMIC attached to the I2C0 bus of the SoC, although the
first community-available V3s board, Lichee Pi Zero, omitted it.
Allow to introduce support for the PMIC on boards with it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner V3/Sochip S3 uses the same die with Allwinner V3s/S3L, but V3 comes
with no co-packaged DDR (DDR3 is usually used externally), and S3L comes
with co-packaged DDR3.
Add support for Allwinner V3/S3 chips by add SoC names to original V3s
choice, and allow to select DDR3.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Import updated device trees from Linux tag v5.9. This picks up new
hardware (PinePhone, PineTab); and it drops the U-Boot specific DTSI
files for the Pinebook and the Teres-I, since the ANX6345 bridge is
now supported upstream.
A couple of headers needed updates for recently-added hardware support.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
There are two different publicly-released revisions of the PinePhone
hardware, versions 1.1 and 1.2; and they need different device trees.
Since some GPIO pins were rerouted, we can use that to distinguish
between them.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Rockchip has many 32bit SoCs and some of them are support SPL_OPTEE now,
only boards with SPL_OPTEE support can fit BINMAN well, other boards
will fail at initr_binman() in U-Boot proper after below patch,
eg. rv1108 board.
83187546ae binman: Support multiple images in the library
Fixes: 79030a4861 ("rockchip: Add Single boot image (with binman, pad_cat)")
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Commit c4cea2bbf9 ("rockchip: Enable building a SPI ROM image on bob")
added an alias spi1 referring to spi@ff1d0000, however there was already
an alias spi0 referring to the same node in rockpro64's u-boot.dtsi, and
having both aliases present broke booting from SPI flash for this board.
Remove the spi0 alias, set the default bus for SPI flash to 1, and
enable support for numbered aliases in SPL so that it uses the same bus
numbering as U-Boot proper. This fixes booting from U-Boot in SPI flash
on the rockpro64 board.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Fixes: c4cea2bbf9 ("rockchip: Enable building a SPI ROM image on bob")
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
In order to enable the Amlogic SM1 MMC controller fix, we need to add a u-boot specific
MMC controller compatible.
This adds a new meson-sm1-u-boot.dtsi and reworks the other -u-boot.dtsi
to use this for SM1 based boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move the asm/arch-meson/sd_emmc.h to a local meson_gx_mmc.h,
remove the useless if/then and fix the meson_gx_mmc.c include.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
- Add a new SMBIOS parser and enable it when booting from coreboot
- Fix up various driver names to avoid dtoc warnings
- Fully enable ACPI support on Google Chromebook Coral
- Add a way to set SMBIOS properties using the devicetree
- Update existing boards to use devicetree for SMBIOS using a new
default sysinfo driver
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
---------------------
- new boards : GE (new B1x5v2), phytec phyCORE-i.MX8MM
- converted doc to reST
- fixes for verdin-imx8mm (Toradex)
- fixes for i.MX thermal driver
- mx7ulp: Align the PLL_USB frequency
- mx53: primary/secondary bmode
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/741465284
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCX6QsVQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76Z29ACfRdzFocIVEOFNm8v5yA1C/FU9q9sAn1kEAot5
vkm2yvDQ7+9vl5G7+ZRn
=rCCX
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20201105' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx for 2021.1
---------------------
- new boards : GE (new B1x5v2), phytec phyCORE-i.MX8MM
- converted doc to reST
- fixes for verdin-imx8mm (Toradex)
- fixes for i.MX thermal driver
- mx7ulp: Align the PLL_USB frequency
- mx53: primary/secondary bmode
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/741465284
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl+frmwcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyP/tCACuq3aixxpR1qzb/Tk6
MnE/Io9ehtq8WfY2M8ks5RK+K5Ezaukh9Edg7YW8j0mvoBZUQ35at8UXanr8XkEx
vk51AkwmTJeckjZ7I8D9m/AIyAU4lVCB/HJp3KRcTdu39bSy+beudg7uinlmvoHP
GSqmGArU58pbHrHi1xVgf8PIbCd52mVPvDu+ghxjKOTPl87WlRCjxelPuMxjLEQ2
8KUuxuXad82S7oRFQz/TDkokf+d8AZVAbOXWqxAnHWNml+qXLWn/oohSQ5+QsYRY
3K2cJFvI3cmAcr9usOX268u0wGd9kDYnQtfym2M8ul70S3pesqUsoiSET9vXq3zL
yu8a
=QSvy
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2021.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2021.01 cycle:
This specific feature set includes the patches for DT required to fix
the warnings for newer DTC version (1.6.0+), i2c and spi bus unit
address.
w+arch/arm/dts/.at91sam9260ek.dtb.pre.tmp:119.21-123.7: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
w+arch/arm/dts/.at91sam9260ek.dtb.pre.tmp:119.21-123.7: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
w+arch/arm/dts/sama5d3xmb.dtsi:64.25-83.7: Warning (i2c_bus_reg): /ahb/apb/i2c@f0018000/camera@0x30: I2C bus unit address format error, expected "30"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
w+arch/arm/dts/.at91sam9g45-gurnard.dtb.pre.tmp:118.21-122.7: Warning (spi_bus_reg): /ahb/apb/spi@fffa4000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
w+arch/arm/dts/.at91sam9g25ek.dtb.pre.tmp:28.25-47.7: Warning (i2c_bus_reg): /ahb/apb/i2c@f8010000/camera@0x30: I2C bus unit address format error, expected "30"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
w+arch/arm/dts/at91sam9g20ek_common.dtsi:100.21-104.7: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
w+arch/arm/dts/.at91sam9g20-taurus.dtb.pre.tmp:79.18-83.4: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
w+arch/arm/dts/.at91sam9261ek.dtb.pre.tmp:124.15-144.7: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/tsc2046@0: SPI bus unit address format error, expected "2"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
w+arch/arm/dts/.at91-vinco.dtb.pre.tmp:131.18-134.7: Warning (i2c_bus_reg): /ahb/apb/i2c@f8024000/rtc@64: I2C bus unit address format error, expected "32"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
GE B1x5v2 patient monitor series is similar to the CARESCAPE Monitor
series (GE Bx50). It consists of a carrier PCB used in combination
with a Congatec QMX6 SoM. This adds U-Boot support using device model
everywhere and SPL for memory initialization.
Proper configuration is provided as 'ge_b1x5v2_defconfig' and the
combined image u-boot-with-spi.imx can be flashed directly to 1024
byte offset to /dev/mtdblock0. Alternatively SPL and u-boot.imx can
be loaded separately via USB-OTG using e.g. imx_usb.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Allow using disable_ldb_di_clock_sources with just the combined
CONFIG_MX6QDL being enabled.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Implement the 'getprisec' subcommand of 'bmode' command for i.MX53 and
also the primary/secondary bootmode switching.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The command 'clocks' shows the following output:
=> clocks
PLL_A7_SPLL 528 MHz
PLL_A7_APLL 529 MHz
PLL_USB 0 MHz
Add some extra spaces so that the PLL_USB information gets aligned with
the previous reported frequencies.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The command 'clocks' shows the following output:
=> clocks
PLL_A7_SPLL 528 MHz
PLL_A7_APLL 529 MHz
PLL_USB 0 MHz
....
[do_mx7_showclocks] addr = 0x9FFB61F1
The last line is not useful at all, so just remove it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Ensure we terminate the line with a CR if we get an invalid sensor device
or reading.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
In order to be able to run the I2C bus at 400Khz, the chip errata[1]
recommends that the peripheral clock runs out of the 24MHz oscillator.
Systems running I2C from OP-TEE before Linux executes - for example to
access a Secure Element [2] providing the cryptographic support - expect
this clock to be configured by the bootloader [3].
[1] IMX6SLCE Rev. 5, 02/2019, ERR007805.
[2] OP-TEE: support for NXP SE05X Plug and Trust (patch on the list).
[3] OP-TEE: check the imx_i2c.c driver (imx6 patch on the list).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
- New PX30 board: Engicam PX30.Core;
- Fix USB HID support for rock960;
- Remove host endianness dependency for rockchip mkimage;
- dts update for rk3288-tinker;
- Enable console MUX for some ROCKPi boards;
- Add config-based ddr selection for px30;
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
PX30.Core needs to mount on top of this Carrier board for creating
complete PX30.Core C.TOUCH 2.0 board.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
