Move the code which reads a partition into its own function. Add a
constant for the number of bytes to 'probe' at the start of the partition.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add some more output to make it easier to see what is going wrong when
a bootdev hunter fails.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This name is a little confusing since it suggests that it sets up the
sibling block device. In fact it sets up a bootdev for it. Rename the
function to make this clearer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
It is not a parse error to have a default value of "0" for a "hex" type
entry, instead of "0x0". However, "0" and "0x0" are not treated the
same even by the tools themselves. Correct this by changing the default
value from "0" to "0x0" for all hex type questions that had the
incorrect default. Fix one instance (in two configs) of a default of "0"
being used on a hex question to be "0x0". Remove the cases where a
defconfig had set a value of "0x0" to be used as the default had been
"0".
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This should be allocating the memory for "item" instead of "menu".
The item struct is 48 bytes instead of 96 (assuming a 64bit system)
so this saves a little memory.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
These lines are supposed to be indented one more tab. Otherwise it's
confusing to read.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The implementation in extlinux_pxe_getfile() does not pass a valid size
to bootmeth_read_file(), so this can fail if the uninited value happens to
be too small.
Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The implementation in distro_efi_try_bootflow_files() does not pass a
valid size to bootmeth_common_read_file(), so this can fail if the
uninted value happens to be too small.
Fix this.
This was reported by someone but I cannot now find the email.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current bootflow-iteration algorithm reads the bootflow file into
an allocated memory buffer so it can be examined. This works well in
most cases.
However, while the common case is that the first bootflow is immediately
booted, it is also possible just to scan for available bootflows, perhaps
selecting one to boot later.
Even with the common case, EFI bootflows can be quite large. It doesn't
make sense to read it into an allocated buffer when we have kernel_addr_t
providing a suitable address for it. Even if we do have plenty of malloc()
space available, it is a violation of U-Boot's lazy-init principle to
read the bootflow before it is needed.
So overall it seems better to make a change.
Adjust the logic to read just the size of the EFI file at first. Later,
when the bootflow is booted, read the rest of the file into the designated
kernel buffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Da Xue <da@libre.computer>
Reported-by: Vincent Stehlé <vincent.stehle@arm.com>
This checks for a network-based bootflow in two places, one of which is
less than ideal. Move the correct test into a function and use it in both
places.
Signed-off-by: Simon Glass <sjg@chromium.org>
uclass_get_device_by_name() is meant to return 0 or a negative error code.
simple_itoa() cannot handle negative numbers.
This leads to output like:
=> bootdev list -p
Seq Probed Status Uclass Name
--- ------ ------ -------- ------------------
c [ ] 18446744073709551614 spi_flash spi.bin@0.bootdev
Convert the status to a positive number. Now we get
Seq Probed Status Uclass Name
--- ------ ------ -------- ------------------
c [ ] 2 spi_flash spi.bin@0.bootdev
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Enabling FIT_SIGNATURE required the old authentication method to be
disabled so disable this for K3 SOCs and enable FIT_SIGNATURE for K3
Platforms.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
[ cleanup the patch ]
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Change the device type from "usb_mass_storage" to "usb" when
booting a script.
Before this change:
=> printenv devtype
devtype=usb_mass_storage
After this change:
=> printenv devtype
devtype=usb
Signed-off-by: John Clark <inindev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some devices keep 2 copies of the bootloader_message in the misc
partition and write each in sequence when updating. This ensures that
there is always one valid copy of the bootloader_message. Teach u-boot
to optionally try a backup bootloader_message from a specified offset if
the primary one fails its CRC check.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
It is is sometimes desired to be able to skip decrementing the number of
tries remaining in an Android A/B boot, and instead just check which
slot will be tried later. This can commonly be be the case for platforms
that want to A/B u-boot itself, but are required to boot from a FAT MBR
partition. In these cases, u-boot must do an early check that the MBR
points to the correct A/B boot partition, and if not rewrite the MBR to
point to the correct one and reboot. Decrementing the try count in this
case is not desired because it means that each u-boot might constantly
ping-pong overwriting the MBR and rebooting until all the retries are
used up.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
It is possible to boot x86-based ChromeOS machines by parsing a table and
locating the kernel and command line. Add a bootmeth for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some Linux parameters can be set automatically by U-Boot, if it knows the
device being used. For example, since U-Boot knows the serial console
being used, it can add parameters for earlycon and console.
Add support for this.
Note that this is an experimental feature and we will see how useful it
turns out to be. It is very handy for ChromeOS, since otherwise it is very
difficult to manually determine the UART address or port number,
particularly in a script.
Provide an example of how this is used with ChromeOS.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a bootflow command to update the command line more easily. This allows
changing a particular parameter rather than editing a very long strings.
It is also easier to handle with scripting.
The new 'bootflow cmdline' command allows getting and setting single
parameters.
Fix up the example output while we are here, since there are a few new
items.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Linux command line consists of a number of words with optional values.
At present U-Boot allows this to be changed using the bootargs environment
variable.
But this is quite painful, since the command line can be very long.
Add a function which can adjust a single field in the command line, so
that it is easier to make changes before booting.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The "bootargs" environment variable is used to set the command-line
arguments to pass to the OS. Use this same mechanism with bootstd as well.
When the variable is updated, it is written to the current bootflow. When
the current bootflow is updated, the environment variable is updated too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It seems better to call this a 'bootdev' since this is name used in the
documentation. The older 'Bootdevice' name is no-longer used and may cause
confusion with the 'bootdevice' environment variable.
Update throughout to use bootdev.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new 'cedit' command which allows editing configuration using an
expo. The configuration items appear as menus on the display.
This is extremely basic, only supporting menus and not providing any way
to load or save the configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
The only way to create an expo at present is by calling the functions to
create each object. It is useful to have more data-driven approach, where
the objects can be specified in a suitable file format and created from
that. This makes testing easier as well.
Add support for describing an expo in a devicetree node. This allows more
complex tests to be set up, as well as providing an easier format for
users. It also provides a better basis for the upcoming configuration
editor.
Signed-off-by: Simon Glass <sjg@chromium.org>
It looks better if menus have a bit of an inset, rather than be drawn hard
up against the background. Also, menu items look better if they have a bit
of spacing between them.
Add theme options for these and implement the required changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
In 'popup' mode, the expo allows moving around the objects in a scene.
When 'enter' is pressed on a menu, it opens and the user can move around
the items in the menu.
Implement this using keypress handles and actions.
Signed-off-by: Simon Glass <sjg@chromium.org>
When a menu is opened, it must be displayed over all other objects in
the scene, so that all its items are visible.
Handle this by drawing the menu object a second time, after all other
objects have been drawn. Draw all of the objects which are dependent
on the menu object.
Signed-off-by: Simon Glass <sjg@chromium.org>
When a popup menu is closed it shows only the selected item. When it is
open it shows a background and all items, with a highlight that can be
moved between the items.
Add the drawing logic for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we only support a single menu, so all that can be pointed to
is the current menu item. Rename this action so that we can also add
an action for pointing to an object. This will allow cycling through
the objects in a scene.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present only a single menu is supported. All items are shown and a
pointer object points to the current item.
Add support for multiple menus, one of which is highlighted, indicated
by the highlight_id property in the scene.
The highlighted menu item has a SCENEOF_POINT flag, indicating that it
is currently pointed to.
The popup menu is normally closed, in which case it shows only the
current menu item. When it is opened, it shows all items, allowing the
user to select one.
Rather than requiring the menu item to have a description, require it to
have a label. Use the label (only) for the popup menu.
With this, most of the drawing and layout logic is complete.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current implementation supports a 'pointer' object which points to
the currently highlighted menu item. We want to support highlighting the
label of the menu item instead, e.g. with inverse video. In this case we
will need to 'unhighlight' the old item and highlight the new one.
As a first step, move the pointer logic into a function. This fixes a
bug where the item is hidden when it should not be.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is a pain to manually set the fonts of all objects to be consistent.
Some spacing settings are also better set globally than by manually
positioning each object.
Add a 'theme' to the expo, to hold this information. For now it includes
only the font size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide a way to set the full dimensions of objects, i.e. including the
width and height.
For menus, calculate the bounding box of all objects in the menu. Set all
labels to be the same size, so that highlighting works correct, once
implemented.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than estimating, measure the text accurately, using the new
vidconsole feature. This allows accurate placement of objects.
Signed-off-by: Simon Glass <sjg@chromium.org>
We currently have just a 'hide' property for each object. In preparation
for adding more properties, convert the struct to use a flags value,
instead of individual booleans. This is more extensible.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present objects only have a position so it is not possible to determine
the amount of space they take up on the display.
Add width and height properties, using a struct to keep all the dimensions
together.
For now this is not used. Future work will set up these new properties.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide a way to set this value so that it is easy to separate the
statically allocated IDs (generated by the caller) from those
generated dynamically by expo itself.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature is different enough from bootstd that it probably deserves
its own log category. It cannot use a uclass since it is not a device.
Add a new category.
Signed-off-by: Simon Glass <sjg@chromium.org>
This functionality current sits in bootstd, but it is more generally
useful. Add a function to load a file into memory, allocating it as
needed. Adjust bootstd to use this version.
Note: Tests are added in the subsequent patch which converts the 'cat'
command to use this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
This should ideally be done once after all scene changes have been made.
Require an explicit call when everything is ready.
Always arrange after a key it sent, just for convenience.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is easier to deal with if it uses the existing string handling,
since we will be able to use translations, etc. in the future.
Update it to use an ID instead of a string.
Signed-off-by: Simon Glass <sjg@chromium.org>
On the arm64 architecture booti_setup() is called for EFI FIT images.
This function call fails because EFI images typically do not have a
kernel signature.
Check that the operating system property "os" of the image is "linux"
before invoking booti_setup().
Fixes: 487b5fa6de ("bootm: Handle kernel_noload on arm64")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Using relative path in a /boot/extlinux/extlinux.conf file fails to load
linux kernel.
Using a /boot/extlinux/extlinux.conf file:
LABEL test
LINUX ../linux/Image
Result in following error:
Retrieving file: ../linux/Image
Skipping test for failure retrieving kernel
Boot failed (err=-14)
However, using sysboot cmd successfully load kernel using same file:
sysboot mmc 1:1 any ${scriptaddr} /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/../linux/Image
Fix relative path using bootmeth extlinux by supplying bootfile path
instead of subdir path in the call to pxe_setup_ctx, same as done in the
sysboot command.
Fixes: 31aefaf89a ("bootstd: Add an implementation of distro boot")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move BOOTSTD_FULL down in the file so that it can be enabled only when
BOOTSTD is enabled. This prevents a build error if BOOTSTD is disabled
but BOOTSTD_FULL is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We cannot be sure what bootmeth a distro will need to use. Add a new
BOOTMETH_DISTRO option which collects these together. Select this from
BOOTSTD_DEFAULTS so that it is clear what is needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make BOOTMETH_EFILOADER depend on EFI_LOADER, select if EFI_LOADER]
Signed-off-by: Tom Rini <trini@konsulko.com>
We use the terms 'distro' to mean extlinux but they are not really the
same. 'Distro' could refer to any method of booting a distribution,
whereas extlinux is a particular method.
Also we sometimes use syslinux, but it is better to use the same term in
all cases.
Rename distro to syslinux and also update bootstd uses of syslinux to use
extlinux instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
In a few cases the error handling is not quite right. Make sure we
return the actual error in distro_efi_read_bootflow_file() rather than
-EINVAL. Return -IO when a file cannot be read. Also show the error name
if available.
This does not change operation, but does make it easier to diagnose
problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
The patch to relax flag requirements was not accepted[1], so we still have
to have separate bootcommands depending on CMD_BOOTFLOW_FULL.
The previous attempt at this did not work, since it used the wrong name
for the options.
Fix this and change the message to mention BOOTSTD_FULL since this affects
not just the flags, but all functionality, so is more likely what the user
wants.
Drop the useless condition on CMD_BOOTFLOW_FULL while we are here.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20230329071655.1959513-2-sjg@chromium.org/
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: a91492b6e9 ("bootstd: Provide a default command")
Armbian uses a script which needs the HUSH parser. It is likely that
other distros will do the same. Enable it by default, just in case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
If there is no partition numbered 1, we decide that there are no
partitions at all. That may not be correct, since at least one Debian
installed has just a single partition numbered 2.
Continue searching up to partition 3, just in case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Renesas RZ/N1 devices contain BootROM code that loads a custom SPKG
image from QSPI, NAND or USB DFU. Support this format in mkimage tool.
SPKGs can optionally be signed, however creation of signed SPKG is not
currently supported.
Example of how to use it:
tools/mkimage -n board/schneider/rzn1-snarc/spkgimage.cfg \
-T spkgimage -a 0x20040000 -e 0x20040000 \
-d u-boot.bin u-boot.bin.spkg
The config file (spkgimage.cfg in this example) contains additional
parameters such as NAND ECC settings.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Adds commands to support DHCP and PXE with IPv6.
New configs added:
- CMD_DHCP6
- DHCP6_PXE_CLIENTARCH
- DHCP6_PXE_DHCP_OPTION
- DHCP6_ENTERPRISE_ID
New commands added (when IPv6 is enabled):
- dhcp6
- pxe get -ipv6
- pxe boot -ipv6
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Fix comments syntax error in SPL_LOAD_FIT_APPLY_OVERLAY description.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
vbe_simple_read_bootflow() calls vbe_simple_read_bootflow_fw()
which is only available when BOOTMETH_VBE_SIMPLE_FW is on.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When loading a file from a block device, efiload_read_file
was using the seq_num of the device (e.g "35" of virtio_blk#35)
instead of the block device id (e.g what you get from running
the corresponding device scan command, like "virtio 0")
This cause EFI booting from these devices to fail as an
invalid device number is passed to blk_get_device_part_str:
Scanning bootdev 'virtio-blk#35.bootdev':
distro_efi_read_bootflow_file start (efi,fname=<NULL>)
distro_efi_read_bootflow_file start (efi,fname=<NULL>)
setting bootdev virtio, 35, efi/boot/bootaa64.efi, 00000000beef9a40, 170800
efi_dp_from_name calling blk_get_device_part_str
dev=virtio devnr=35 path=efi/boot/bootaa64.efi
blk_get_device_part_str (virtio,35)
blk_get_device_by_str (virtio, 35)
** Bad device specification virtio 35 **
Using default device tree: dtb/qemu-arm.dtb
No device tree available
0 efi ready virtio 1 virtio-blk#35.bootdev.par efi/boot/bootaa64.efi
** Booting bootflow 'virtio-blk#35.bootdev.part_1' with efi
blk_get_device_part_str (virtio,0:1)
blk_get_device_by_str (virtio, 0)
No UEFI binary known at beef9a40 (image buf=00000000beef9a40,addr=0000000000000000)
Boot failed (err=-22)
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present when debugging is off, bootdev_find_in_blk() sometimes fails
to find a valid bootflow, e.g. with virtio. Accessing the 'blk' variable
later in the function seems to correct it.
Move the 'ret' check before the debug statement and set the block device
again aftewards, to work around this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the -l flag to indicate whether to report missing uclasses.
Also try to be more helpful when no devices are found. For example, when
we see something 'scsi0' requested and nothing was found, this indicates
that there are no SCSI devices, so show a suitable message.
Move messages out of the low-level functions so that silent operation
is possible.
This means they are never reported unless BOOTSTD_FULL is enabled, since
the -l flag cannot otherwise be set.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
The current EFI implementation has a strange quirk where it watches
loaded files and uses the last-loaded file to determine the device that
is being booted from.
This is confusing with bootstd, where multiple options may exist. Even
loading a device tree will cause it to go wrong. There is no API for
passing this information, since the only entry into booting an EFI image
is the 'bootefi' command.
To work around this, call efi_set_bootdev() for EFI images, if possible,
just before booting.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should only store the FDT filename if we were able to determine one.
Adjust the logic for this.
This corrects the case where no FDT is needed to boot, such as with EFI
using ACPI.
Signed-off-by: Simon Glass <sjg@chromium.org>
When building with clang we get a warning that rdaddr could be
uninitialized in one case. While this cannot functionally happen, we can
easily silence the warning.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the script loading code to recognize when script data is stored
externally from the FIT metadata (i.e., built with `mkimage -E`).
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable the support for boot image header version 3 and 4
using abootimg command.
In order to use version 3 or 4:
1- Vendor boot image address should be given to abootimg cmd.
abootimg addr $1 $vendor_boot_load_addr
2- "ramdisk_addr_r" env variable (ramdisk address) should be set to host
the ramdisk : generic ramdisk + vendor ramdisk
Replace "struct andr_boot_img_hdr_v0*" by "void *" in
some functions since v3 and v4 are now supported as well.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Add support for boot image version 3 and 4 in
android_image_get_dtb_img_addr().
Since the dtb is now included in vendor_boot image
instead of boot image, extract the dtb address from
vendor_boot image when a v3 or v4 is used.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
In version 3 and 4 of boot image header, the vendor specific
command line are located in vendor boot image. Thus, use
extra command line to add those cmd to bootargs.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Version 3 and 4 of boot image header introduced
vendor boot ramdisk: Please check include/android_image.h
for details.
The ramdisk is now split into a generic ramdisk in boot image
and a vendor ramdisk in vendor boot image.
Support the new vendor ramdisk.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Since boot image header version 3 and 4 introduced vendor boot image,
use the following functions to fill the generic android
structure : andr_image_data:
- android_boot_image_v3_v4_parse_hdr()
- android_vendor_boot_image_v3_v4_parse_hdr()
Update android_image_get_data() to support v3 and v4
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Introduce vendor boot image for version 3 and 4 of boot image header.
The vendor boot image will hold extra information about kernel, dtb
and ramdisk.
This is done to prepare for boot image version 3 and 4 support.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
android_image_get_dtbo() is used to get recovery DTBO via abootimg cmd.
This is not supported in boot image header v3 and v4. Thus, print an
error message when v1,v2 header version are not used.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Content print is not supported for version 3 and 4 of boot image header.
Thus, only print that content when v2 is used.
Update android_print_contents() to print an error message
when trying to print boot image header version 3 or 4 content.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Move from andr_boot_img_hdr_v0 to andr_image_data
structure to prepare for boot image header
version 3 and 4.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
andr_image_data structure is used as a global representation of
boot image header structure. Introduce this new structure to
support all boot header versions : v0,v1.v2.v3.v4 and to support
v3 and v4 while maitaining support for v0,v1,v2.
The need of using andr_image_data comes from the change of header
structure in both version 3 and 4.
Rework android_image_get_kcomp() to support this new struct.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
With the new vendor boot image introduced in versions 3 and 4
of boot image header, the header check must be done for both boot
image and vendor boot image. Thus, replace android_image_check_header()
by is_android_boot_image_header() to only refer to boot image header check.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Android introduced boot header version 3 or 4.
The header structure change with version 3 and 4 to support
the new updates such as:
- Introducing Vendor boot image: with a vendor ramdisk
- Bootconfig feature (v4)
Change andr_img_hdr struct name to maintain support for version v0,
v1 and v2 while introducing version 3 and 4.
Signed-off-by: Safae Ouajih <souajih@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
In case fitImage support is disabled, and image_locate_script() is
passed a fitImage, then the 'data' variable is used uninitialized.
Drop into the default: branch of the switch-case statement and do
not return the uninitialized data, and do not modify the return
pointer either, just print an error message.
Reported by clang build:
"
$ make HOSTCC=clang CC=clang KCFLAGS=-Werror sandbox64_defconfig && make HOSTCC=clang CC=clang KCFLAGS=-Werror
...
boot/image-board.c:1006:7: error: variable 'data' is used uninitialized whenever switch case is taken [-Werror,-Wsometimes-uninitialized]
case IMAGE_FORMAT_LEGACY:
^~~~~~~~~~~~~~~~~~~
include/image.h:608:29: note: expanded from macro 'IMAGE_FORMAT_LEGACY'
^~~~
boot/image-board.c:1128:19: note: uninitialized use occurs here
*datap = (char *)data;
^~~~
boot/image-board.c:1001:11: note: initialize the variable 'data' to silence this warning
u32 *data;
^
= NULL
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These two features use a lot of common options. Move them into a common
CONFIG to reduce duplication.
Use 'select' for most options since these are things that boards aren't
supposed to override. For now it is not possible to disable
BOOT_DEFAULTS but we may take another look later.
Note that five options use 'imply' to match existing behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Rework a bit so we don't grow so many platforms unintentionally]
Signed-off-by: Tom Rini <trini@konsulko.com>
For EFI, the distro boot scripts search in three different directories
for the .dtb file. The SOC-based filename fallback is supported only for
32-bit ARM.
Adjust the code to mirror this behaviour.
Also some boards can use a prior-stage FDT if one is not found in the
normal way. Support this and show a message in that case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Mark Kettenis <kettenis@openbsd.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_DM_RNG defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_CMD_BOOTEFI_BOOTMGR defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_CMD_PSTORE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_CMD_FDT defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_CMD_BOOTM_PRE_LOAD defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
