Driver can configure the SPI clock frequnecy to the
target value of "spi-max-frequency" property in
the device tree. The frequency is divided from HCLK,
200MHz. Usually, the ASPEED SPI clock frequency range
is between 12.5MHz and 100MHz. On AST2600, the lowest
SPI clock frequency can be about 780kHz.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
If "decoded-ranges" is defined in the device tree, the
driver will apply the decoded address ranges from this
property to the controller during probe stage.
This patch refers to the following OpenBMC u-boot patch.
https://patchwork.ozlabs.org/project/openbmc/list/?series=306969
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
There are some known HW problems about decoded
range register configurations on existing AST2500 and
AST2600 platforms. Additional callback function,
adjust_decoded_sz, is added to solve these problems
on each platform. Besides, aspeed_spi_trim_decoded_size
function is added to modify overall decoded address
size for fitting the maximum AHB decoded size.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
From the HW point of view, the performance of
command read mode is greater than user mode slightly.
Thus, dirmap read framework is introduced to achieve
this goal. In dirmap_create, command read mode is
configured. Usually, the decoded address area with flash
size is assigned to each CS. CPU can thus access the
SPI flash as normal memory in dirmap_read function.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
This adds support for the dirmap API to the spi-nor subsystem, as
introduced in Linux commit df5c21002cf4 ("mtd: spi-nor: use
spi-mem dirmap API").
This patch is synchronize from the following patch
https://patchwork.ozlabs.org/project/uboot/patch/20210205043924.149504-4-seanga2@gmail.com/
The corresponding Linux kernel SHA1 is df5c21002cf4.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
This adds the dirmap API originally introduced in
Linux commit aa167f3fed0c
("spi: spi-mem: Add a new API to support direct mapping").
This also includes several follow-up patches and fixes.
Changes from Linux include:
* Added Kconfig option
* Changed struct device to struct udevice
* Changed struct spi_mem to struct spi_slave
This patch is obtained from the following patch
https://patchwork.ozlabs.org/project/uboot/patch/20210205043924.149504-3-seanga2@gmail.com/
The corresponding Linux kernel SHA1 is aa167f3fed0c.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Although AST2400 is EOL officially, in order to achieve
sustainability and completeness, AST2400 part is added.
For AST2400,
- Five CSs are supported by FMC controller.
- SPI1 controller only supports single CS and there is
no address segment address register. The CE control
register of SPI1 is located at the offset 0x04 and
the 4-byte address mode control bit is bit 13 of
this register.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Add ASPEED BMC FMC/SPI memory controller driver with
spi-mem interface for AST2500 and AST2600 platform.
There are three SPI memory controllers embedded in an ASPEED SoC.
- FMC: Named as Firmware Memory Controller. After AC on, MCU ROM
fetches initial device boot image from FMC chip select(CS) 0.
- SPI1: Play the role of a SPI Master controller. Or, there is a
dedicated path for HOST(X86) to access its BIOS flash mounted
under BMC. spi-aspeed-smc.c implements the control sequence when
SPI1 is a SPI master.
- SPI2: It is a pure SPI flash controller. For most scenarios, flashes
mounted under it are for pure storage purpose.
ASPEED SPI controller supports 1-1-1, 1-1-2 and 1-1-4 SPI flash mode.
Three types of command mode are supported, normal mode, command
read/write mode and user mode.
- Normal mode: Default mode. After power on, normal read command 03h or
13h is used to fetch boot image from SPI flash.
- AST2500: Only 03h command can be used after power on
or reset.
- AST2600: If FMC04[6:4] is set, 13h command is used,
otherwise, 03h command.
The address length is decided by FMC04[2:0].
- Command mode: SPI controller can send command and address
automatically when CPU read/write the related remapped
or decoded address area. The command used by this mode
can be configured by FMC10/14/18[23:16]. Also, the
address length is decided by FMC04[2:0]. This mode will
be implemented in the following patch series.
- User mode: It is a traditional and pure SPI operation, where
SPI transmission is controlled by CPU. It is the main
mode in this patch.
Each SPI controller in ASPEED SoC has its own decoded address mapping.
Within each SPI controller decoded address, driver can assign a specific
address region for each CS of a SPI controller. The decoded address
cannot overlap to each other. With normal mode and command mode, the
decoded address accessed by the CPU determines which CS is active.
When user mode is adopted, the CS decoded address is a FIFO, CPU can
send/receive any SPI transmission by accessing the related decoded
address for the target CS.
This patch only implements user mode initially. Command read/write
mode will be implemented in the following patches.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Add FWSPICS1 and SPI1CS1 in AST2500 pinctrl group.
On AST2500 EVB, FWSPICS1 can be supported by default.
An extra jumper, J45, should be configured before
enabling SPI1CS1.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
User can get correct HCLK frequency during driver probe stage
by adding the following configuration in the device tree.
"clocks = <&scu ASPEED_CLK_AHB>".
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
cmd:
- bdinfo - guard LMB code to run only when LMB is enabled
timer:
- convert arm twd timer to DM
power-domain:
- Skip loading config object for Versal
xilinx:
- Fix logic when dfu_alt_info is generated
- Define only mmc devnum not partition
- Add xlnx prefix to GEM compatible string
- Add missing tca6416 to zynqmp SC - vck190
- Add env redund offset
- Enable CMD_GREPENV/SETEXPR by default
- Move board_get_usable_ram_top() to common location
- Add support for SOC detection
net/gem:
- Check rate before setting it up
microblaze:
- drop CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE
- Show cache size in bdinfo
spi:
- cadence_qspi: driver updates
- zynqmp_gqspi: driver updates
- zynqmp_gqspi: Add tap delays for Versal
zynq:
- Enable mkeficapsule compilation
- Use CONFIG_SPL_FS_LOAD_PAYLOAD_NAME for dfu_alt_info
- Align bss and end of u-boot image to 64bits
- Align qspi node name with Linux kernel
- DT: List OCM memory
zynqmp:
- Fix AES cache handling with a user provided key
- SOM: Add mtd partition for secure OS storage area
- Add ref_clk property for REFCLKPER calculation
- Fix mdio bus description for vck190-sc
xilinx-mini:
- Remove unneeded configs
- Disable LMB
versal:
- Enable i2c mux pca954x by default
- Define CONFIG_CQSPI_REF_CLK
- Enable power domain driver
- Enable zynqmp_gqspi driver
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYyBsQQAKCRDKSWXLKUoM
IR2tAJ9GfXT90zd0eU7KeZzhekX9wrAxNACglOVqanFpEr2ITSa3Pv8+FknD4XE=
=VuHq
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2023.01-rc1
cmd:
- bdinfo - guard LMB code to run only when LMB is enabled
timer:
- convert arm twd timer to DM
power-domain:
- Skip loading config object for Versal
xilinx:
- Fix logic when dfu_alt_info is generated
- Define only mmc devnum not partition
- Add xlnx prefix to GEM compatible string
- Add missing tca6416 to zynqmp SC - vck190
- Add env redund offset
- Enable CMD_GREPENV/SETEXPR by default
- Move board_get_usable_ram_top() to common location
- Add support for SOC detection
net/gem:
- Check rate before setting it up
microblaze:
- drop CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE
- Show cache size in bdinfo
spi:
- cadence_qspi: driver updates
- zynqmp_gqspi: driver updates
- zynqmp_gqspi: Add tap delays for Versal
zynq:
- Enable mkeficapsule compilation
- Use CONFIG_SPL_FS_LOAD_PAYLOAD_NAME for dfu_alt_info
- Align bss and end of u-boot image to 64bits
- Align qspi node name with Linux kernel
- DT: List OCM memory
zynqmp:
- Fix AES cache handling with a user provided key
- SOM: Add mtd partition for secure OS storage area
- Add ref_clk property for REFCLKPER calculation
- Fix mdio bus description for vck190-sc
xilinx-mini:
- Remove unneeded configs
- Disable LMB
versal:
- Enable i2c mux pca954x by default
- Define CONFIG_CQSPI_REF_CLK
- Enable power domain driver
- Enable zynqmp_gqspi driver
To quote the author:
This series makes a further attempt to get closer to having all tests
run in parallel. It introduces a new 'make pcheck' option which runs
tests in parallel, skipping those that are not compatible.
A number of fixes are included for existing tests. The vboot test is
updated to only run a single scenario in 'quick' mode.
This makes use of pytest's parallel-testing features. The resulting
times (including incremental building with LTO) on a 16-core machine are
as follows:
make pcheck - 1 minute 6 seconds
make qcheck - 3 minutes
make check - 5 minutes 15 seconds
Note that this is not a fair comparison, since 'make pcheck' omits a
number of tests, even more than 'make qcheck'.
Code supports board detection based on information available in EEPROM in
legacy or FRU format. But this is not enough for emulation and simulation
systems which are lacking these identification EEPROMs. But SOC itself has
normally registers for SOC identification. Based on them it is possible to
compose detected name. That's why prepare infrastructure in common location
for SOC platform detection which is called before board platform detection.
SOC platform detection shouldn't detect real silicon and should fallback to
current existing mechanism to identify boards based on EEPROMs.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/329a8da338927b082e26a958bf69bb18af072420.1662460837.git.michal.simek@amd.com
Few lines are extented to next line though they can fit in 80 character
limit, align them to single line. No functional change.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-6-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As the flash sizes are increasing day by day, QSPI can have devices of
size > 512MB. In qspi driver we are trying to read all the data at once
using DMA.
The DMA descriptor destination size is only 29bits long.
QSPIDMA_DST_SIZE 0xFF0F0804
BITS: 1:0 Reserved to keep word alignment
BITS: 28:2 Number of 4-byte words the DMA will transfer
BITS: 31:29 Reserved: Returns 0 when read, writes ignored
So we can only transfer data of 0x1FFFFFF0(512MB minus 4bytes) bytes.
Anything above will overflow this register and will ignore higher bits
above 29 bits.
Change the DMA functionality if the requested size is greater than or
equal to 512MB to read 256MB chunks.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-5-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for io-mode transfers. This is necessary for UBIFS to work
properly with spi-nor devices. The driver will work in IO mode when
"has-io-mode" is passed from device tree instead of DMA.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
GQSPI driver is using it but this function is never called for Versal
because it is removed by linker. But function should be declared to avoid
this build warning:
drivers/spi/zynqmp_gqspi.c: In function 'zynqmp_qspi_set_tapdelay':
drivers/spi/zynqmp_gqspi.c:378:3: warning: implicit declaration of function
'zynqmp_mmio_write' [-Wimplicit-function-declaration]
378 | zynqmp_mmio_write(IOU_TAPDLY_BYPASS_OFST,
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As per driver model we should enumerate plat structure only in
of_to_plat() and should be used only in probe(). Copy required
plat structure info into priv structure in probe() and use priv
structure across the driver. So replace plat with priv structure across
the driver.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220824113847.7482-4-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
In cadence_spi_read_id we are using STIG mode to read flash id's.
Call cadence_qspi_apb_command_read_setup() to setup cmd, addr and data
bus width properly before cadence_qspi_apb_command_read().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220824113847.7482-3-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
In cadence_spi_probe, cadence_qspi_versal_flash_reset() is called to reset
the flash device. Looks like there is a mistake in previous series of
patches where it is defined as cadence_spi_versal_flash_reset() but
called as cadence_qspi_versal_flash_reset. Since there is a weak function
defined with the same name this issue was not caught.
Fix the issue by renaming cadence_spi_versal_flash_reset as
cadence_qspi_versal_flash_reset().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220824113847.7482-2-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add bdinfo_print_size() helper to display size variables (such as cache
sizes) in bdinfo format. The size is printed as "xxx Bytes", "xxx KiB",
"xxx MiB", "xxx GiB", etc as needed;
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Jason Liu <jason.hui.liu@nxp.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-3-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Check snprintf() return value for errors.
Make microblaze_cpu_get_desc() directly return snprintf() error code if
ret < 0. Otherwise, if the return value is greater than or equal to size,
the resulting string is truncated, so return -ENOSPC.
Fixes: 816226d27e ("cpu: add CPU driver for microblaze")
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-2-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
These macros are not used anymore in microblaze code since commit
f113d7d303 ("Convert CONFIG_SPL_STACK to Kconfig"), so remove them.
Fixes: f113d7d303 ("Convert CONFIG_SPL_STACK to Kconfig")
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-1-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The commit ce39ee28ec ("zynqmp: Do not place u-boot to reserved memory
location") adds functionality for ZynqMP to read reserved memory node and
do not place U-Boot to reserved location. This functionality is generic
across all Xilinx SOCs that's why move it to common location to be used by
all Xilinx SOCs.
On zynq platform this is also fixing issue where U-Boot was placed to
locating which was reserved already which ends up with error message
"ERROR: reserving fdt memory region failed (addr=30000000 size=10000000
flags=4)" which is shown when bdinfo is called.
Tested on vck190, zcu102, zc706 and kc705 to cover all platforms.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b0817807912f7c7af6a8e1cf9ee04e5ab5de5f6a.1661430188.git.michal.simek@amd.com
ENV_OFFSET_REDUND config is by default set to 0 for flashes. Saving the env
variables is overwriting data at 0 offset, which is wrong. So add default
redund env offset for Zynq, ZynqMP, Versal and microblaze platforms.
Configured ENV_OFFSET_REDUND offsets by ENV_OFFSET + (2 * ENV_SIZE).
In case of versal, we configured ENV_OFFSET_REDUND at 0x7F00000 instead
of 0x7F80000. As BOOT_SCRIPT_OFFSET is already configured at 0x7F80000.
Added ENV_OFFSET_REDUND in Kconfig for microblaze due to dependency of
ENV_IS_IN_SPI_FLASH config.
Below table specifies platform specific env and env redund offsets.
PLAT ENV_OFFSET ENV_OFFSET_REDUND
---- ---------- -----------------
ZYNQ 0xE0000 0xE40000
ZYNQMP 0x1E00000 0x1E80000
VERSAL 0x7F40000 0x7F00000
MICROBLAZE 0x1080000 0x10C0000
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/92656dc08f0f5a749d62b71ca6e77fe1be72e9e0.1661340204.git.michal.simek@amd.com
Added ref_clk 'ref' property for GUCTL_REFCLKPER and GFLADJ_REFCLK_FLADJ
calculation. This property configure correct value for SOF/ITP counter
and period of ref_clk.
This patch adds 'ref' property for both dwc3_0 and dwc3_1 cores.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/417545b948ea12a9301a5e80851f98523be2b443.1661259809.git.michal.simek@amd.com
Update MTD partitions of Kria device trees to allocate 128KB of QSPI
memory for secure OS. Increased "SHA256" partition size & changed
starting address of "User" partition to accommodate the new partition
"Secure OS Storage"
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9cc64b8c731d11439de73d0af54c65080068f00b.1661242681.git.michal.simek@amd.com
The commit 53b406369e ("DFU: Check the number of arguments and argument
string strictly") added strict control over string that 0:1 partition
definition is not valid anymore that's why use only device number without
partition ID. Device is specified by 2nd parameter and partition by 3rd.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/840eca944f4f2abeeb63b5d724f9ba5fe9a9213b.1660055571.git.michal.simek@amd.com
Zynq can use efi capsule infrastructure that's why enable it by default.
For capsule generation for zynq you can use:
pushd spl
../tools/mkeficapsule -g "1ba29a15-9969-40aa-b424-e86121618664" boot.bin \
--index 1 ../capsule1.bin
popd
./tools/mkeficapsule -g "1a5178f0-87d3-4f36-ac63-3b31a23be305" u-boot.img \
--index 2 capsule2.bin
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a8194ecfa7932f2d8ada5ee508b2a026c782f15e.1660055571.git.michal.simek@amd.com
With commit 55b3ba4c2b ("spi: cadence_qspi: Migrate CONFIG_CQSPI_REF_CLK
to Kconfig") CONFIG_CQSPI_REF_CLK is moved to Kconfig.
The static value via Kconfig is a fallback option in case of clock
framework is not enabled or fails for some reason.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/fe7c38a19e878c307d5b75311bbfd8cf6c1f601e.1659691195.git.michal.simek@amd.com
