Function 'sprintf' does not check buffer boundaries but outputs
to the buffer of fixed size which could potentially cause buffer
overflow. Use a safer function to replace it.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Don't store it in a u32.
Don't dereference the bus address as if it were a virtual address
(fixes 284231e49a ("ahci: Support splitting of read transactions
into multiple chunks")).
Fixes crash on boot in MPC8641HPCN_36BIT target.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Vadim Bendebury <vbendeb@chromium.org>
Acked-by: York Sun <yorksun@freescale.com>
In stead of user_buffer_size, transfer_size should be used to pass to
ahci_device_data_io(). transfer_size is the length that we want the
low level function to transfer each time.
If we use user_buffer_size which is the totally data length as parameter,
low level function will actually create many SGs to transfer as many data
as possible each time. That will produce many redundant data transfer.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Each time U-Boot boots on Intel Crown Bay board, the displayed hard
drive information is wrong. It could be either wrong capacity or just
a 'Capacity: not available' message. After enabling the debug switch,
we can see the scsi inquiry command did not execute successfully.
However, doing a 'scsi scan' in the U-Boot shell does not expose
this issue.
SCSI: Target spinup took 0 ms.
SATA link 1 timeout.
AHCI 0001.0100 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst
scanning bus for devices...
ahci_device_data_io: 0 byte transferred. <--- scsi inquiry fails
ahci_device_data_io: 512 byte transferred.
ahci_device_data_io: 512 byte transferred.
ahci_device_data_io: 512 byte transferred.
Device 0: (0:0) Vendor: ATA Prod.: Rev: ?8
Type: Hard Disk
Capacity: 912968.3 MB = 891.5 GB (1869759264 x 512)
Found 1 device(s).
So uninitialized contents on the stack were passed to dev_print() to
display those wrong information.
The symptom were observed on two hard drives (one is Seagate, the
other one is Western Digital). The fix is to make sure the AHCI
interface is not busy by checking the error and status information
from task file register after enabling the port in ahci_port_start()
before proceeding other operations like scsi_scan().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This allow the platform to handle a custom reset sequence.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Extract controller reset code from ahci_host_init() into separate
ahci_reset().
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
The macro __iomem is defined in include/linux/compiler.h.
Let's include it rather than double __iomem defines.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.adi@gmail.com>
- fix crash when sata device is not initialized
- remove disable_sata_clock() since it is not clear which clock for which
device should be disabled here
- call disable_sata_clock() for mx6 in preboot_os instead
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Add reset_sata() to the sata driver interface and implement it
for dwc_ahsata. This function cleans up after sata_init(), and
therefore accepts a device number like sata_init() does.
A dummy implementation is provided for the rest of the drivers.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Except the first loop, init_sata() should return 0 instead of 1
in the others.
This patch fix the issue of the 2nd sata port not workable on pci-sata card.
Signed-off-by: Pengbo Li <Pengbo.Li@freescale.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
The logic of the return statement in sata_port_status() calls for a
bitwise 'AND' operator, not logical 'AND'. Fix the typo.
Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
The DMA/FIS buffers are set in ahci_port_start() which is called
after ahci_host_init(). So don't start the DMA engine here
(i.e. don't set FIS_RX)
This fixes the following error at kernel boot on OMAP platforms (e.g. DRA7x)
WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x260/0x358()
44000000.ocp:L3 Custom Error: MASTER SATA TARGET GPMC (Idle): Data Access in User mode during Functional access
Signed-off-by: Roger Quadros <rogerq@ti.com>
This would be useful to start moving various config options.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Define the new common function sata_port_status() which can be
used to query the sata driver for the state of ports, and implement it
for dwc_ahsata.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done
for sun7i only since I don't have access to any other sunxi platforms
with sata included.
The PHY setup is derived from the Alwinner releases and Linux, but is mostly
undocumented.
The Allwinner AHCI controller also requires some magic (and, again,
undocumented) DMA initialisation when starting a port. This is added under a
suitable ifdef.
This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on
contents of Linux DTS files, including SATA power pin config taken from the
DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
In 73545f75b6 "ahci: wait longer for link" I increased the
timeout to 40ms based on the observed behaviour of a WD disk on a
Cubietruck. Since then Karsten Merker and myself have both
observed timeouts with HGST disks (Karsten on Cubietruck, me on
Cubieboard2). Increasing the timeout to ~175ms fixes this, so go
to 200ms for a bit of headroom.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Karsten Merker <merker@debian.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The IMX6QUAD/DUAL have SATA, but the IMX6SOLO/DL do not. Return failure
instead of attempting a memory access that results in a data abort and reset.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Commit 2faf5fb82e introduced a regression that causes a data
abort when running scsi init followed by scsi reset.
There are 2 problems with the original commit
1) ALLOC_CACHE_ALIGN_BUFFER() allocates memory on the stack but is
assigned to ataid[port] and used by other functions.
2) The function ata_scsiop_inquiry() tries to free memory which was
never allocated on the heap.
Fix these problems by using tmpid as a temporary cache aligned buffer.
Allocate memory separately for ataid[port] and re-use it if required.
Fixes: 2faf5fb82e (ahci: Fix cache align error messages)
Reported-by: Eli Nidam <elini@marvell.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
I have observed timeouts on a cubietruck.
The increase to 40ms is completely arbitrary and Works For Me(tm). I
couldn't find a good reference for how long you are supposed to wait,
although googling around it seems like tens of ms rather than single
digits is more common. I don't think there is any harm in waiting a bit
longer.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
With d6a320d we moved some clock externs out of blackfin_local.h and
into clock.h but now need to include <asm/clock.h> in more drivers to
avoid warnings.
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Tom Rini <trini@ti.com>
Provide a way to use any host file or device as a block device in U-Boot.
This can be used to provide filesystem access within U-Boot to an ext2
image file on the host, for example.
The support is plumbed into the filesystem and partition interfaces.
We don't want to print a message in the driver every time we find a missing
device. Pass the information back to the caller where a message can be printed
if desired.
Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net>
Signed-off-by: Simon Glass <sjg@chromium.org>
- Removed change to part.c get_device_and_partition()
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the ATA ID buffer to the cache-line boundary. This gets rid
of the below error mesages on ARM v7 platforms.
scanning bus for devices...
ERROR: v7_dcache_inval_range - start address is not aligned - 0xfee48618
ERROR: v7_dcache_inval_range - stop address is not aligned - 0xfee48818
CC: Aneesh V <aneesh@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
If malloc() fails, we don't want to continue in ahci_init() and
ahci_init_one(). Also print a more informative error message on
malloc() failures.
CC: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
libata already has similar functions as implemented in the ahci code.
Refactor the code to use the libata variants and remove the dependency on
ata.h. Convert some defines to use the version from libata.h. Also, remove
some unnecessary memset's of bss data.
This is a step toward hopefully merging ahci.c and dw_ahsata.c which are
essentially the same driver.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Tom Rini <trini@ti.com>
Based on Linux libata code, most drives are less than 10 sec, but some
need up to 20 sec.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Tom Rini <trini@ti.com>
Some Intel SSDs can send a COMINIT after the initial COMRESET. This causes
the link to go down and we need to re-initialize the link.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Move the link bring-up handling to a separate weak function in order to
allow platforms to override it. This is needed on highbank platform which
needs special phy handling.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
gcc 4.7 will generate unaligned accesses to local char arrays, so make
them static to avoid that.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Tom Rini <trini@ti.com>
The AHCI driver was incorrectly using the Capabilities register NP (number
of ports) field to determine which ports to activate. This commit changes
it to correctly use the PORTS_IMPL register as a port map.
Signed-off-by: Richard Gibbs <richard.gibbs@calxeda.com>
Reviewed-by: Tom Rini <trini@ti.com>
Add a const keyword to the sect_buf argument of
ide_write_data to fix the following warning:
cmd_ide.c: In function '__ide_output_data':
cmd_ide.c:548: warning: passing argument 2 of 'ide_write_data' discards qualifiers from pointer target type
/devel/u-boot.git/include/ide.h:76: note: expected 'ulong *' but argument is of type 'const ulong *'
Also modify the driver-model documentation to
match with the new prototype.
Compile tested only.
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
log2 of the device block size serves as the shift value used to calculate
the block number to read in file systems when implementing avaiable block
sizes.
It is needed quite often in file systems thus it is pre-calculated and
stored in the block device descriptor.
Signed-off-by: Egbert Eich <eich@suse.com>
'bool' is defined in random places. This patch consolidates them into a
single header file include/linux/types.h, using stdbool.h introduced in C99.
All other #define, typedef and enum are removed. They are all consistent with
true = 1, false = 0.
Replace FALSE, False with false. Replace TRUE, True with true.
Skip *.py, *.php, lib/* files.
Signed-off-by: York Sun <yorksun@freescale.com>
Currently we have "unsigned long blkcnt" which is fine with
CONFIG_SYS_64BIT_LBA undefined because "lbaint_t" is basically the same
"unsigned long".
If CONFIG_SYS_64BIT_LBA gets defined "lbaint_t" is defined as "unsigned
long long".
Even though not many embedded systems have CONFIG_SYS_64BIT_LBA defined
it's good to have types in function implementation that match exactly
with prototypes.
Signed-off-by: Alexey Brodkin <alexey.brodkin@gmail.com>
System ACE compact flash controller supports either 8-bit (default) or
16-bit data transfers. And in corresponding driver we need to implement
read/write of 16-bit data words properly for both modes of operation.
In existing code if width==8 both branches get executed which may cause
unexpected behavior of SystemAce controller.
Addition of "else" fixes described issue and execution is done as
expected for both (8-bit and 16-bit) data bus widths.
Signed-off-by: Alexey Brodkin <alexey.brodkin@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
sata_sil.c:371:7: warning: symbol 'sil_sata_rw_lba28' was not declared. Should it be static?
sata_sil.c:399:7: warning: symbol 'sil_sata_rw_lba48' was not declared. Should it be static?
sata_sil.c:429:6: warning: symbol 'sil_sata_cmd_flush_cache' was not declared. Should it be static?
sata_sil.c:441:6: warning: symbol 'sil_sata_cmd_flush_cache_ext' was not declared. Should it be static?
sata_sil.c:489:7: warning: symbol 'sata_read' was not declared. Should it be static?
sata_sil.c:505:7: warning: symbol 'sata_write' was not declared. Should it be static?
sata_sil.c:526:5: warning: symbol 'init_sata' was not declared. Should it be static?
sata_sil.c:588:5: warning: symbol 'scan_sata' was not declared. Should it be static?
fsl_sata.c:59:6: warning: symbol 'dprint_buffer' was not declared. Should it be static?
fsl_sata.c:187:42: warning: incorrect type in assignment (different base types)
fsl_sata.c:187:42: expected unsigned int [unsigned] [usertype] cda
fsl_sata.c:187:42: got restricted __le32 [usertype] <noident>
fsl_sata.c:291:6: warning: symbol 'fsl_sata_hardware_reset' was not declared. Should it be static?
fsl_sata.c:418:27: warning: incorrect type in assignment (different base types)
fsl_sata.c:418:27: expected unsigned int [unsigned] [usertype] dba
fsl_sata.c:418:27: got restricted __le32 [usertype] <noident>
fsl_sata.c:424:41: warning: incorrect type in assignment (different base types)
fsl_sata.c:424:41: expected unsigned int [unsigned] [usertype] ext_c_ddc
fsl_sata.c:424:41: got restricted __le32 [usertype] <noident>
fsl_sata.c:431:41: warning: incorrect type in assignment (different base types)
fsl_sata.c:431:41: expected unsigned int [unsigned] [usertype] ext_c_ddc
fsl_sata.c:431:41: got restricted __le32 [usertype] <noident>
fsl_sata.c:442:22: warning: incorrect type in assignment (different base types)
fsl_sata.c:442:22: expected unsigned int [unsigned] [usertype] cda
fsl_sata.c:442:22: got restricted __le32 [usertype] <noident>
fsl_sata.c:446:31: warning: incorrect type in assignment (different base types)
fsl_sata.c:446:31: expected unsigned int [unsigned] [usertype] prde_fis_len
fsl_sata.c:446:31: got restricted __le32 [usertype] <noident>
fsl_sata.c:448:22: warning: incorrect type in assignment (different base types)
fsl_sata.c:448:22: expected unsigned int [unsigned] [usertype] ttl
fsl_sata.c:448:22: got restricted __le32 [usertype] <noident>
fsl_sata.c:460:28: warning: incorrect type in assignment (different base types)
fsl_sata.c:460:28: expected unsigned int [unsigned] [usertype] attribute
fsl_sata.c:460:28: got restricted __le32 [usertype] <noident>
fsl_sata.c:623:6: warning: symbol 'fsl_sata_flush_cache' was not declared. Should it be static?
fsl_sata.c:667:5: warning: symbol 'fsl_sata_rw_ncq_cmd' was not declared. Should it be static?
fsl_sata.c:710:6: warning: symbol 'fsl_sata_flush_cache_ext' was not declared. Should it be static?
fsl_sata.c:725:6: warning: symbol 'fsl_sata_software_reset' was not declared. Should it be static?
fsl_sata.c:760:5: warning: symbol 'ata_low_level_rw_lba48' was not declared. Should it be static?
fsl_sata.c:795:5: warning: symbol 'ata_low_level_rw_lba28' was not declared. Should it be static?
the following compiler warnings show up after fixing the above, so
remove those three functions:
fsl_sata.c:59:13: warning: 'dprint_buffer' defined but not used [-Wunused-function]
fsl_sata.c:291:13: warning: 'fsl_sata_hardware_reset' defined but not used [-Wunused-function]
fsl_sata.c:726:13: warning: 'fsl_sata_software_reset' defined but not used [-Wunused-function]
Other than that, the following are fixed by __iomem annotation:
fsl_sata.c:84:39: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:84:39: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:84:39: got unsigned int volatile *addr
fsl_sata.c:172:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:172:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:172:26: got unsigned int *<noident>
fsl_sata.c:175:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:175:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:175:19: got unsigned int *<noident>
fsl_sata.c:181:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:181:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:181:19: got unsigned int *<noident>
fsl_sata.c:184:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:184:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:184:26: got unsigned int *<noident>
fsl_sata.c:186:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:186:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:186:19: got unsigned int *<noident>
fsl_sata.c:189:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:189:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:189:26: got unsigned int *<noident>
fsl_sata.c:191:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:191:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:191:19: got unsigned int *<noident>
fsl_sata.c:194:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:194:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:194:26: got unsigned int *<noident>
fsl_sata.c:195:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:195:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:195:19: got unsigned int *<noident>
fsl_sata.c:198:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:198:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:198:19: got unsigned int *<noident>
fsl_sata.c:201:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:201:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:201:19: got unsigned int *<noident>
fsl_sata.c:204:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:204:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:204:26: got unsigned int *<noident>
fsl_sata.c:205:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:205:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:205:19: got unsigned int *<noident>
fsl_sata.c:208:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:208:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:208:26: got unsigned int *<noident>
fsl_sata.c:209:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:209:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:209:19: got unsigned int *<noident>
fsl_sata.c:212:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:212:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:212:26: got unsigned int *<noident>
fsl_sata.c:213:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:213:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:213:19: got unsigned int *<noident>
fsl_sata.c:216:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:216:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:216:19: got unsigned int *<noident>
fsl_sata.c:219:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:219:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:219:19: got unsigned int *<noident>
fsl_sata.c:222:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:222:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:222:19: got unsigned int *<noident>
fsl_sata.c:225:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:225:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:225:26: got unsigned int *<noident>
fsl_sata.c:227:19: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:227:19: expected unsigned int volatile [noderef] <asn:2>*addr
fsl_sata.c:227:19: got unsigned int *<noident>
fsl_sata.c:242:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:242:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:242:26: got unsigned int *<noident>
fsl_sata.c:256:32: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:256:32: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:256:32: got unsigned int *<noident>
fsl_sata.c:262:26: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:262:26: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:262:26: got unsigned int *<noident>
fsl_sata.c:274:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:274:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:274:53: got unsigned int *<noident>
fsl_sata.c:275:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:275:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:275:53: got unsigned int *<noident>
fsl_sata.c:276:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:276:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:276:53: got unsigned int *<noident>
fsl_sata.c:277:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:277:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:277:53: got unsigned int *<noident>
fsl_sata.c:278:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:278:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:278:53: got unsigned int *<noident>
fsl_sata.c:279:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:279:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:279:53: got unsigned int *<noident>
fsl_sata.c:280:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:280:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:280:53: got unsigned int *<noident>
fsl_sata.c:281:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:281:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:281:53: got unsigned int *<noident>
fsl_sata.c:282:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:282:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:282:53: got unsigned int *<noident>
fsl_sata.c:283:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:283:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:283:53: got unsigned int *<noident>
fsl_sata.c:284:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:284:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:284:53: got unsigned int *<noident>
fsl_sata.c:285:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:285:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:285:53: got unsigned int *<noident>
fsl_sata.c:286:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:286:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:286:53: got unsigned int *<noident>
fsl_sata.c:287:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:287:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:287:53: got unsigned int *<noident>
fsl_sata.c:288:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:288:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:288:53: got unsigned int *<noident>
fsl_sata.c:289:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:289:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:289:53: got unsigned int *<noident>
fsl_sata.c:290:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:290:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:290:53: got unsigned int *<noident>
fsl_sata.c:291:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:291:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:291:53: got unsigned int *<noident>
fsl_sata.c:292:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:292:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:292:53: got unsigned int *<noident>
fsl_sata.c:293:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:293:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:293:53: got unsigned int *<noident>
fsl_sata.c:294:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:294:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:294:53: got unsigned int *<noident>
fsl_sata.c:295:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:295:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:295:53: got unsigned int *<noident>
fsl_sata.c:296:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:296:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:296:53: got unsigned int *<noident>
fsl_sata.c:297:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:297:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:297:53: got unsigned int *<noident>
fsl_sata.c:298:53: warning: incorrect type in argument 1 (different address spaces)
fsl_sata.c:298:53: expected unsigned int const volatile [noderef] <asn:2>*addr
fsl_sata.c:298:53: got unsigned int *<noident>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Currently, this driver uses a 28bit interface to AHCI, this
limits the number of blocks addressable to 2^28, or the max
disk size to 512(2^28) or about 137GB. This change allows
supporting drives up to about 2TB.
Testing this is a bit difficult. There is test code that
can be inserted into U-Boot that will write test patterns
into certain unused blocks. These patterns can be manually
checked using 'dd' after boot. Another way is to confirm the
original error that exposed this bug is fixed. IOW: see if
AU (Auto Update) will now work on the drive. Also, check
that there are no warning messages from the 'cgpt' utility.
Signed-off-by: Walter Murphy <wmurphy@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Writes in u-boot are so rare, and the logic to know when is
the last write and do a flush only there is sufficiently
difficult. Just do a flush after every write. This incurs,
usually, one extra flush when the rare writes do happen.
Signed-off-by: Marc Jones <marc.jones@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add HDD handling to the SSD-only AHCI driver, by separately dealing with
spin-up and link-up.
Signed-off-by: Marc Jones <marc.jones@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Note: These are timeout values and not delay values, so the event being
timed out will complete whenever it is actually ready, with a
measurement granularity of 1 millisecond, up till the timeout value.
Therefore, there is no effect on SSD booting.
The values were determined by instrumenting the code and measuring the
actual time taken by several different models of HDD for each of the
parameters and then adding 50% more for the spinup value and just
doubling the command timeout value.
Signed-off-by: Walter Murphy <wmurphy@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Exynos5 automatically performs DMA when the SATA controller executes
commands. This adds the necessary dcache-to-memory flush &
invalidation calls to allow the DMA to properly function.
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the assignment of various physical memory buffers used by the
SATA controller to explicitly be denoted as physical addresses.
The memory is identity-mapped, so these function calls are a nop, but
they provide good semantic documentation for any maintainers.
The return value of virt_to_phys() is 'unsigned long'. On machines
where sizeof(unsigned long) != sizeof(pointer), a cast through
(uintptr_t) is needed to appease the compiler due to the potential of
losing the upper 32 bits of the address.
In compilation this scenario, a physical address could be 64-bits, yet
the C pointer environment only allows 32-bit addresses; the constraint
is that pointers cannot address more than 4Gb of memory and if
virt_to_phys() ever returns an out-of-range value for the physical
address, there are issues with emmory mapping which must be solved.
However, since the memory is identify mappeed, there is no problem
introducing the cast: the original pointer will reside in 32-bits, so
the physical address will also be within in 32-bits.
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This fixes a spelling error in a message which can be output to the
console.
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This cleanup replaces the hardcoded use of '20', which represents the
number of bytes in the FIS, with sizeof(fis).
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
In the structure returned by the ATA identify device command, there are two
fields which describe the device capacity. One is a 32 bit data type which
reports the number of sectors as a 28 bit LBA, and the other is a 64 bit data
type which is for a 48 bit LBA. If the device doesn't support 48 bit LBAs,
the small value is the only value with the correct size. If it supports more,
if the number of sectors is small enough to fit into 28 bits, both fields
reflect the correct value. If it's too large, the smaller field has 28 bits of
1s, 0xfffffff, and the other field has the correct value.
The AHCI driver is implemented by attaching to the generic SCSI code and
translating on the fly between SCSI binary data structures and AHCI data
structures. It responds to requests to execute specific SCSI commands by
executing the equivalent AHCI commands and then crafting a response which
matches what a SCSI disk would send.
The AHCI driver now considers both fields and chooses the correct one when
implementing both the SCSI READ CAPACITY (10) and READ CAPACITY (16) commands.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The "scsi write" command requires support from underlying driver.
This CL enables SCSI_WRITE10 in AHCI driver.
Tested in U-Boot console, try to i/o with sector #64:
scsi read 1000 40 1
md.b 1000 200 # check if things are not 0xcc
mw.b 1000 cc 200 # try to fill with 0xcc
scsi write 1000 40 1
mw.b 1000 0 200 # fill with zero
md.b 1000 200 # should be all 0
scsi read 1000 40 1
md.b 1000 200 # should be all 0xcc
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This command doesn't really do anything when talking to a SATA device, and
sending it confuses some of them. This change makes sending the command
optional, and defaults to not. The situations where it should be sent are not
the common case.
With the standard SSD in the machine, here are some times with the option
turned off:
1. 8277
2. 8273
3. 8050
And turned on:
1. 8303
2. 8155
3. 8276
Sending that command seems to have no meaningful effect on performance.
This fixes problems with an SSD marked Toshiba NV6424, Taiwan 11159AE P
and TC58NVG5D2FTA10.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
- print the correct speed
- print all the AHCI capability flags
(information taken from Linux kernel driver)
- clean up some comments
For example, this might show the following string:
AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3 impl SATA mode
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Commit-Ready: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stefan Reinauer <reinauer@chromium.org>
- remove unused ssleep macro
- add some useful debugging information
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The existing code waits a whole second for the AHCI controller to reset.
Instead, let's poll the status register to see if the reset has
succeeded and return earlier if possible. This brings down the time for
AHCI probing from 1s to 20ms.
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
With an Intel AHCI controller, the driver does not operate properly
if the requested amount of blocks to read exceeds 255.
It is probably possible to specify 0 as the block count and the driver
will read 256 blocks, but it was decided to limit the number of blocks
read at once to 128 (it should be a power of 2 for the optimal
performance of solid state drives).
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
- block_dev_desc_t says that block_(read|write) take lbaint_t for blkcnt
not ulong.
- We also move the extern of sata_dev_desc into <sata.h>
- Remove now duplicate declarations from driver-specific headers.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
sata_write() takes a const void as the last argument. Fixing this means
we also need to make ata_low_level_rw_lba{28,48} also take a const void.
Signed-off-by: Tom Rini <trini@ti.com>
- sata_write() takes a const void as the last argument. Fixing this
means we also need to make ata_low_level_rw_lba{28,48} also take a
const void.
- Both sata_{read,write} take lbaint_t for blkcnt and ulong for blknr
Signed-off-by: Tom Rini <trini@ti.com>
sata_write() takes a const void as the last argument. Fixing this means
we also need to make ata_low_level_rw_lba{28,48} also take a const void.
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
We set sata_curr_device to 0 right after returning from init_sata(), so there's
no point in setting it to the last scanned driver at this point.
Note: there are more duplicities with cmd_sata, but those might be required,
as the code seems to reset the entire controller on every scan, ignoring the
requested port number.
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Use CONFIG parameters only at one location to simplify
the code. Also create ace_readw/writew functions.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Drop mdelay() macros since we already have a common mdelay() func.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This driver is part of Freescale's LTIB for
MX5 / MX6.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Terry Lv <r65388@freescale.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
pata_bfin.c: In function 'bfin_ata_identify':
pata_bfin.c:887:2: warning: format '%x' expects type 'unsigned int',
but argument 2 has type 'lbaint_t'
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Consider that ide_preinit() succeed if at least one port is successfully
initialized. This allows to iniatialize IDE support on a board with two
SATA ports but a single hard disk available.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Fix:
sata_dwc.c: In function 'scan_sata':
sata_dwc.c:535:38: warning: variable 'udma_mask' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kazuaki Ichinohe <kazuichi@fsi.co.jp>
On the P1022/P1013, the work-around for erratum SATA_A001 was implemented
only if U-Boot initializes SATA, but SATA is not initialized by default. So
move the work-around to the CPU initialization function, so that it's always
executed on the SOCs that need it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
sata_dwc.c: In function 'sata_dwc_softreset':
sata_dwc.c:444:5: warning: variable 'status' set but not used [-Wunused-but-set-variable]
sata_dwc.c:443:6: warning: variable 'serror' set but not used [-Wunused-but-set-variable]
sata_dwc.c: In function 'scan_sata':
sata_dwc.c:654:16: warning: variable 'lba_desc' set but not used [-Wunused-but-set-variable]
sata_dwc.c:538:16: warning: variable 'xfer_mask' set but not used [-Wunused-but-set-variable]
sata_dwc.c: In function 'ata_dev_read_id':
sata_dwc.c:747:14: warning: variable 'reason' set but not used [-Wunused-but-set-variable]
sata_dwc.c: In function 'ata_dev_read_sectors':
sata_dwc.c:1810:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
sata_dwc.c: In function 'ata_dev_write_sectors':
sata_dwc.c:1994:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
sym53c8xx.c: In function 'scsi_write_dsp':
sym53c8xx.c:456:16: warning: variable 'val' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
ahci.c: In function 'ata_scsiop_read10':
ahci.c:564:6: warning: variable 'lba' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
sata_sil3114.c: In function 'sata_identify':
sata_sil3114.c:174: warning: format '%x' expects type 'unsigned int', but
argument 2 has type 'lbaint_t'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
ahci.c: In function 'ahci_port_start':
ahci.c:401: warning: format '%x' expects type 'unsigned int', but argument 2 has
type 'struct ahci_cmd_hdr *'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
There are several mdelay() definitions in the driver and
board code. Remove them all and provide a common mdelay()
in lib/time.c.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Add the Silicon Image series PCI Express to
Serial ATA controller support, including Sil3132,
Sil3131 and Sil3124.
The SATA controller can be used to load kernel.
The features list:
- Supports 1-lane 2.5 Gbit/s PCI Express
- Supports one/two/four independent Serial ATA channels
- Supports Serial ATA Generation 2 transfer rate of 3.0 Gbit/s
- Supports LBA28 and LBA48
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Aaron Williams <Aaron.Williams@cavium.com>
Tested-by: Lan Chunhe <b25806@freescale.com>
If CONFIG_LBA48 is not defined, the element lba48 of struct sata_dev_desc
is not avaible, and can't be used.
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
If we don't want to build support for any partition types we can now
add #undef CONFIG_PARTITIONS in a board config file to keep this from
being compiled in. Otherwise boards assume this is compiled in by
default
Signed-off-by: Matthew McClintock <msm@freescale.com>
Before the actual initialization do a hard reset of the SATA port and the
connected device.
changes v1->v2:
- add comment for udelay
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Faraday's ftide020_s is an IDE-AHB controller for SoC design.
This patch add the u-boot driver (PIO) of ftide020 ATA (IDE) driver.
IDE commands include read, info, and other functions has been implemented.
Because this IDE controller support AHB interface only which is differ
from other most IDE controller supports PCI interface. Some registers
access is required during CMD/DATA I/O. Hence a configuration
"CONFIG_IDE_AHB" is required to be defined according to the feature in
cmd_ide.c.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Drop warnings due to unused variables.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
mvsata_ide_initialize_port(): adjust init sequence (SStatus
should be checked only after all writes to SControl) and
return success/failure to ide_preinit().
Also, as some tests showed init durations in the hundreds
of us, raise the time-out to 01 ms to be on the safe side.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
This driver only provides initialization code; actual driving
is done by cmd_ide.c using the ATA compatibility mode of the
Marvell SATAHC controller.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
On the MPC85xx platform if we have SATA its connected on SERDES.
Determing if SATA is enabled via sata_initialize should not be board
specific and thus we move it out of the MPC8536DS board code.
Additionally, now that we have is_serdes_configured() we can determine
if the given SATA port is enabled and error out if its not in the
driver.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For P1022 SATA host controller, the data snoop bit of DW3 in PRDT
is moved to bit28.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
After power on, the SATA host controller of P1022 Rev1 is configured
in legacy mode instead of the expected enterprise mode.
Software needs to clear bit[28] of HControl register to change to
enterprise mode after bringing the host offline.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cast first parameter to sata_cpy()
In /drivers/block/ata_piix.h, ata_id_has_lba48(), ata_id_has_lba(),
ata_id_has_dma(), ata_id_u32(), ata_id_u64() are all defined in
include/libata.h which is included in ata.h which is included by all files
which include ata_piix.h (only ata_piix.c) so these definitions are
supurflous to (and conlict with) this in libata.h. Interestingly, my
compiler complains about ata_id_u64 already being defined, but not
ata_id_u32
ata_dump_id() is defined in include/libata.h and should not be static
(maybe should even use ata_dump_id() in libata.c
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
ahci.c: In function 'ata_scsiop_read_capacity10':
ahci.c:616: warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update fsl_sata to use common structures instead of casting
back and forth between the fsl specific ones and the common ones
(which are identical).
fsl_sata.c: In function 'scan_sata':
fsl_sata.c:550: warning: dereferencing pointer 'cfis' does break strict-aliasing rules
fsl_sata.c:549: warning: dereferencing pointer 'cfis' does break strict-aliasing rules
fsl_sata.c:548: warning: dereferencing pointer 'cfis' does break strict-aliasing rules
fsl_sata.c:545: note: initialized from here
fsl_sata.c:592: warning: dereferencing pointer 'cfis' does break strict-aliasing rules
fsl_sata.c:590: warning: dereferencing pointer 'cfis' does break strict-aliasing rules
fsl_sata.c:588: warning: dereferencing pointer 'cfis' does break strict-aliasing rules
fsl_sata.c:586: warning: dereferencing pointer 'cfis' does break strict-aliasing rules
fsl_sata.c:579: warning: dereferencing pointer 'cfis' does break strict-aliasing rules
...
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds a SATA harddisk driver for the canyonlands.
This patch is kernel driver's porting.
This patch corresponded to not cmd_scsi but cmd_sata.
This patch divided an unused member with ifndef __U_BOOT__ in the structure.
[environment variable, boot script]
setenv bootargs root=/dev/sda7 rw
setenv bootargs ${bootargs} console=ttyS0,115200
ext2load sata 0:2 0x400000 /canyonlands/uImage
ext2load sata 0:2 0x800000 /canyonlands/canyonlands.dtb
fdt addr 0x800000 0x4000
bootm 0x400000 - 0x800000
If you drive SATA-2 disk on Canyonlands, you must change parts from
PI2PCIE212 to PI2PCIE2212 on U25. We confirmed to boot by using
following disks:
1.Vendor: Fujitsu Type: MHW2040BS
2.Vendor: Fujitsu Type: MHW2060BK
3.Vendor: HAGIWARA SYS-COM:HFD25S-032GT
4.Vendor: WesternDigital Type: WD3200BJKT (CONFIG_LBA48 required)
5.Vendor: WesternDigital Type: WD3200BEVT (CONFIG_LBA48 required)
6.Vendor: Hitachi Type: HTS543232L9A300 (CONFIG_LBA48 required)
7.Vendor: Seagate Type: ST31000333AS (CONFIG_LBA48 required)
8.Vendor: Transcend Type: TS32GSSD25S-M
9.Vendor: MTRON Type: MSD-SATA1525-016
Signed-off-by: Kazuaki Ichinohe <kazuichi at fsi.co.jp>
The curr_device variable really should be namespaced with a "sata_" prefix
since it is only used by the sata code. It also avoids random conflicts
with other pieces of code (like cmd_mmc):
common/libcommon.a(cmd_sata.o):(.data.curr_device+0x0):
multiple definition of `curr_device'
common/libcommon.a(cmd_mmc.o):(.data.curr_device+0x0): first defined here
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mflash is fusion memory device mainly targeted consumer eletronic and
mobile phone.
Internally, it have nand flash and other hardware logics and supports
some different operation (ATA, IO, XIP) modes.
IO mode is custom mode for the host that doesn't have IDE interface.
(Many mobile targeted SoC doesn't have IDE bus)
This driver support mflash IO mode.
Followings are brief descriptions about IO mode.
1. IO mode based on ATA protocol and uses some custom command. (read
confirm, write confirm)
2. IO mode uses SRAM bus interface.
Signed-off-by: unsik Kim <donari75@gmail.com>
judging from other printfs in the same file, it seems ata should be
postpended with the interface number, not the address of the global
port variable. Fixes this for current u-boot-mpc83xx tree:
Configuring for MPC8349ITX board...
sata_sil3114.c: In function 'sata_bus_softreset':
sata_sil3114.c:99: warning: format '%u' expects type 'unsigned int', but argument 2 has type 'struct sata_port *'
sata_sil3114.c:108: warning: format '%u' expects type 'unsigned int', but argument 2 has type 'struct sata_port *'
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The code assumes that the pci bus address and the virtual
address used to access a region are the same, but they might
not be. Fix this assumption.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
This is a port of the Linux Blackfin on-chip ATAPI driver to U-Boot.
Signed-off-by: Sonic Zhang <Sonic.Zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The driver need wait for the device updating signature to host.
If we don't wait for it, the driver can not detect the device(disk)
when the system powers up.
Signed-off-by: Dave Liu <daveliu@freescale.com>
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).
Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Current libata.h of u-boot is out of sync from linux kernel,
this patch make it be consistent with linux kernel.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Tor Krill <tor@excito.com>
Add the Freescale on-chip SATA controller driver to u-boot,
The SATA controller is used on the 837x and 8315 targets,
The driver can be used to load kernel, fs and dtb.
The features list:
- 1.5/3 Gbps link speed
- LBA48, LBA28 support
- DMA and FPDMA support
- Two ports support
Signed-off-by: Dave Liu <daveliu@freescale.com>
original ata_piix driver is using IDE framework, not real
SATA framework. For now, the ata_piix driver is only used
by x86 sc520_cdp board. This patch makes the ata_piix driver
use the new SATA framework, so
- remove the duplicated command stuff
- remove the CONFIG_CMD_IDE define in the sc520_cdp.h
- add the CONFIG_CMD_SATA define to sc520_cdp.h
Signed-off-by: Dave Liu <daveliu@freescale.com>
move the cmd_sata.c from common/ to drivers/ata_piix.c,
the cmd_sata.c have some part of ata_piix controller drivers.
consolidate the driver to have better framework.
Signed-off-by: Dave Liu <daveliu@freescale.com>
