This header will be used by the DDR driver (lmc). Its ported from the
2013 Cavium / Marvell U-Boot repository.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header will be used by the DDR driver (lmc). Its ported from the
2013 Cavium / Marvell U-Boot repository.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header is used by the upcoming DDR driver and potentially by other
drivers ported from the 2013 Cavium / Marvell U-Boot repository.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the memory controller (LMC) DT node to the Octeon 3 dtsi
file. It also adds the L2C DT node, as this is referenced by the DDR
driver.
Signed-off-by: Stefan Roese <sr@denx.de>
The GPIO bank name for banks J and K are not correct when using the
'gpio' command from the console.
The driver derives the bank name from the device tree instance string by
using the instance value and adding 'A': gpio0@xxaddrxx is Bank A,
gpio1@yyaddryy is Bank B and so on.
On the PIC32, there is no Bank I so instances 8 and 9 need to be
incremented as a minimum change.
An alternative (less opaque) implementation would be to use a bank-name
property instead but this would require modifying the driver code too.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
GPIO state cannot be changed via the device tree (e.g. with gpio-hog) or
using the 'gpio' command from the console.
The root cause is a discrepancy between the driver and the device tree:
the driver code expects an absolute I/O address in the <reg> property,
while the device tree defines the address relative to a declaration in
the parent pinctrl node.
Changing the device tree to fix a driver issue would normally be wrong,
however:
- I have run the first version of U-Boot in which this driver appears
(v2016.03) and the same problem exists, so this is not a regression;
- There is no code that references a parent device tree node that might
suggest the intent of the author was to parse the DT as it exists now;
- The equivalent Linux PIC32 GPIO driver also uses absolute addresses
for the GPIO <reg> property. This change brings the U-Boot DT more
into line with Linux.
Additionally, the data sheet (Microchip ref. 60001361H) shows that the
register set to control a GPIO bank spans 0xE0 bytes, but the device
tree specified size is only 0x48 bytes.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
The PIC32MZ DA Starter Kit does not need the card detect workaround
because the SDCD signal line is connected properly. Disable the
workaround in this case.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
With the planned removal of bi_memstart & bi_memsize, this patch now
moves the references to the better suiting gd->ram_base/ram_size
variables.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This header file should not be included in other header files. Remove it
from each one and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch selects DM_SPI & DM_I2C for MIPS Octeon. DM_GPIO, DM_SERIAL
and DM_ETH are already selected.
Additionally the selections are now alphabetically sorted.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds very basic minimal support for the Marvell Octeon 3
CN73xx based EBB7304 EVK. Please note that the basic Octeon port does
not support DDR3/4 initialization yet. To still use U-Boot on with this
port, the L2 cache (4MiB) is used as RAM. This way, U-Boot can boot
to the prompt on this board.
Supported devices:
- UART
- reset
- CFI parallel NOR flash
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the code to copy itself from bootrom location to a
different location (TEXT_BASE) to the Octeon platform. Its used in
this case to copy the complete U-Boot image into L2 cache, which
greatly improves the bootup time - especially in regard to the
very long and complex DDR4 init code.
The Kconfig symbol CONFIG_MIPS_MACH_EARLY_INIT is enabled with this
patch for Octeon.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds very basic support for the Octeon III SoCs. Only
CFI parallel NOR flash and UART is supported for now.
Please note that the basic Octeon port does not include the DDR3/4
initialization yet. This will be added in some follow-up patches
later. To still use U-Boot on with this port, the L2 cache (4MiB on
Octeon III CN73xx) is used as RAM. This way, U-Boot can boot to the
prompt on such boards.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the optional call to mips_mach_early_init() to start.S
at a very early stage. Its disabled per default. It can be used for
very early machine / platform specific init code. Its called very
early and at this stage the PC is allowed to differ from the linking
address (CONFIG_TEXT_BASE) as no absolute jump has been performed until
this call.
It will be used by thje Octeon platform.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Sync asm/mipsregs.h with Linux 5.7. Also replace the custom
symbols EBASE_CPUNUM and EBASE_WG with the according symbols
from Linux.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Sync asm/addrspace.h with Linux 5.7
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Sync asm/asm.h with Linux 5.7.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
This macro only served as a wrapper for CKSEG1ADDR() with an
exception for CONFIG_TB0229. CONFIG_TB0229 doesn't exist, thus
use CKSEG1ADDR() directly.
This also prepares for an upcoming asm header sync with Linux.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Add an own Kconfig symbol for the initial disabling of caches
invoked from generic start code.
Also add an own Kconfig symbols for the initialization of caches
invoked from generic start code.
Until now both code paths could only be disabled with
CONFIG_SKIP_LOWLEVEL_INIT. But this is not flexible enough for
RAM boot scenarios like EJTAG or SPL payload or for machines
which don't require cache initialization or which want to
provide their own cache implementation.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Logically this code belongs to cache_init.S.
If a complex SoC needs to replace the generic cache init,
mips_cache_disable() can now be called from custom start.S files.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
change_k0_cca() is called multiple times. Move the code for
changing to KSEG1 to a macro to avoid code duplication.
Also fix missing change to KSEG1 when changing to CONF_CM_CACHABLE_COW.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Since commit 703ec9ddf9 ("MIPS: Stop building position independent code")
the relocation code was completely reworked and removed from start.S.
Remove some left-overs of the old code.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
This patch adds __weak to invalidate_dcache_range() in lib/cache.c. This
makes it possible to overwrite this function by a platforms specific
version, which will be done for Octeon.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds __weak to flush_cache() in lib/cache.c. This makes it
possible to overwrite this function by a platforms specific version,
like done with the Octeon base port.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the usage of CONFIG_MIPS_L2_CACHE without
CONFIG_MIPS_CM, which is what is needed for the newly added Octeon
platform.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes the R_MIPS_NONE define from 0 to a magic value. This
makes it possible to better detect any forbidden pre-relocation usage
of BSS variables, as they are often zero'ed and then relocation is
stopped too early.
Additionally the error message is improved to also print the faulting
address. This helps finding the root-cause for this breakage by
comparing this address with the values in System.map.
This patch helps a lot when working on pre-relocation code, like the
Octeon DDR init code, where such variables have hit me multiple times
now.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
This patch opts-out the compilation of get_tbclk() if
CONFIG_SYS_MIPS_TIMER_FREQ is not defined. This is used on the Octeon
platform, where the weak get_tbclk() function is overwritten by its
platform specific one.
Signed-off-by: Stefan Roese <sr@denx.de>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Small patch to add support for VoCore/VoCore2 board.
VoCore is open hardware and runs OpenWrt/LEDE.
It has WIFI, USB, UART, 20+ GPIOs but is only one inch square.
It will help you to make a smart house, study embedded system
or even make the tiniest router in the world.
Details about this SoM can be found at "https://vocore.io/v2.html".
Signed-off-by: Mauro Condarelli <mc5686@mclink.it>
Reviewed-by: Stefan Roese <sr@denx.de>
The current implementations have some issues detecting the correct
values:
dqs_find_max() will return "last passing fieldval + 1" instead of
"last passing fieldval". Also it will return "maxval + 1" in the
case that all fieldvals are tested valid (without error).
dqs_find_min() will not test the "lowest" value because of using ">"
instead of ">=".
This patch now rewrites these functions to fix those issues. Also,
this patch uses the same approach of a for loop in both functions making
it easier to read and maintain.
Since the variables are integers now, we can use min()/max(), which
handles the wrap around case for fieldval=0: return (0 - 1).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
This change is made to enable comparison of integer variables, which
might be negative in the next patch. No functional change is intended
in this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
This function returns "-1" (true) upon error. So the function name does
not match its implementation which is confusing. This patch renames the
function to dqs_test_error() which makes the code easier to read.
Also change the return type to bool and return "true" or "false".
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for mt7628 reference board. SPL_DM and DT are not
enabled for SPL to save about 17KiB for u-boot-spl.bin.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch enables SPL for all mtmips boards. And also remove defconfig
files which are intend to build ram bootable u-boot files.
SPL_DM and OF_CONTROL are enabled for both boards.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds SPL support for mtmips platform. The lowlevel architecture
is split into SPL and the rest parts are built into a memory loadable
u-boot image. Optional SPL_DM and OF_CONTROL are also supported.
The increment of size is very small (< 10 KiB) if SPL_DM and OF_CONTROL are
not enabled and the memory bootable u-boot (u-boot.img) is generated
automatically so there is not need to add a separate config for it.
A lzma compressed payload (u-boot-lzma.img) is also generated and it will
be combined with u-boot-spl.bin to form the unified ROM bootable binary
u-boot-mtmips.bin.
A spl loader is added to support uncompress the payload.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch rewrites the mtmips architecture with the following changes:
1. Move MT7628 soc parts into a subfolder.
2. Lock parts of D-Cache as temporary stack.
3. Reimplement DDR initialization in C language.
4. Reimplement DDR calibration in a clear logic.
5. Add full support for auto size detection for DDR1 and DDR2.
6. Use accurate CPU clock depending on the input xtal frequency for timer
and delay functions.
Note:
print_cpuinfo() has incompatible parts with MT7620 so it's moved into
mt7628 subfolder.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The initial stack on some platforms is too small to hold a large malloc
space. This patch adds a option to allow these platforms not reserving the
malloc space on initial stack. These platforms should set the malloc base
after DRAM is usable.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Currently CONFIG_MIPS_INIT_STACK_IN_SRAM assumes the memory space for the
initial stack can be used directly. However on some platform the SRAM needs
initialization, e.g. lock cache.
This patch adds an option to allow a new function mips_sram_init() being
called before setup_stack_gd.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a new pinmux for UART2, which shares the pins with SPIS.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
SoCs of mtmips can use different CPU frequencies depending on the HW/SW
configurations. For example mt7628 uses 580MHz clock if the input xtal
frequency is 40MHz, and 575MHz clock if the xtal is 25MHz. Upon cold boot
the CPU uses the xtal frequency directly.
So hardcoding the timer frequency (half of the CPU frequency) in
CONFIG_SYS_MIPS_TIMER_FREQ is not a good idea for this case.
This patch adds a mtmips-specific field timer_freq to arch_global_data.
This field will be used later in mtmips-specific get_tbclk() to provide
accurate timer frequency in different boot stage.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch replaces sysreset-syscon with sysreset-resetctrl for mt7628 soc.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a MIPS specific jump_to_image_no_args() implementation,
which flushes the U-Boot proper image loaded from the boot device in
SPL before jumping to it.
It has been noticed on MT76x8, that this cache flush is needed. Other
MIPS platforms might need it as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
u_boot_list is not only used by DM, but also by some SPL image load methods
such as spl_nor.c.
This patch adds an option CONFIG_SPL_LOADER_SUPPORT in conjunction with
CONFIG_SPL_DM surrounding the u_boot_list section to make sure SPL image
loaders can be correctly built into u-boot SPL without DM enabled.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
If CONFIG_SPL_OF_CONTROL is enabled for SPL and CONFIG_OF_SEPARATE is also
enabled, the dtb will be appended to the u-boot-spl.bin.
When calling dm_init_and_scan() in SPL, fdtdec_setup() will try to locate
dtb at the end of u-boot-spl.bin, by referencing to _image_binary_end.
However _image_binary_end is currently missing in u-boot-spl.lds.
This patch adds _image_binary_end to u-boot-spl.lds to make sure linking
u-boot-spl will not fail.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
When setting up initial stack, global data will also be put in the stack,
and being cleared.
The assembler instructions for clearing gd is as follows:
move t0, k0
1:
PTR_S zero, 0(t0)
blt t0, t1, 1b
PTR_ADDIU t0, PTRSIZE
t0 is the start address of gd, t1 is the end address of gd (t0 + GD_SIZE).
[PTR_ADDIU t0, PTRSIZE] is in the delay slot of [blt t0, t1, 1b], so it
will be executed before the branch operation.
However the comparison for the BLT instruction is done before executing the
delay slot. This means when the last word just before k1 is cleared, the
loop will continue to run once. This will clear an extra word at k1, which
is outside the global data.
Global data is placed at the top of the stack. If the initial stack is a
SRAM or locked cache, the area outside them may be inaccessible. A write
operation performed in this area may cause an exception.
To solve this, [PTR_ADDIU t0, PTRSIZE] should be placed before the BLT
instruction.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Both mt7620 and mt7628 has the same cache configuration. There is no need
to use CONFIG_SYS_CACHE_SIZE_AUTO to probe it at runtime.
Add them into Kconfig to reduce some code size.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
In U-Boot the exception vector base will be moved to top of memory, to be
used to display register dump when exception occurs.
But some old linux kernel does not honor the base set in CP0_EBASE. A
modified exception vector base will cause kernel crash.
This patch adds an option to enable reset exception vector base to its
previous value, or a user configured value before booting linux kernel.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Pull in changes that have been pending in our 'next' branch. This
includes:
- A large number of CI improvements including moving to gcc-9.2 for all
platforms.
- amlogic, xilinx, stm32, TI SoC updates
- USB and i2c subsystem updtaes
- Re-sync Kbuild/etc logic with v4.19 of the Linux kernel.
- RSA key handling improvements
Align Kconfig and Kbuild logic to Linux 4.19 release with minimal impact
on files outside of this scope.
Our previous Kconfig sync was done by commit 5972ff077e ("kconfig /
kbuild: re-sync with Linux 4.18").
In this particular re-sync in order to keep clang support working a
number of related changes needed to be pulled in that had been missed
previously. Not all of these changes we easily traceable and so have
been omitted from the list below.
The imported Linux commits are:
[From prior to v4.18]
9f3f1fd29976 kbuild: Add __cc-option macro
d7f14c66c273 kbuild: Enable Large File Support for hostprogs
6d79a7b424a5 kbuild: suppress warnings from 'getconf LFS_*'
24403874316a Shared library support
86a9df597cdd kbuild: fix linker feature test macros when cross compiling with Clang
0294e6f4a000 kbuild: simplify ld-option implementation
[From v4.18 to v4.19]
96f14fe738b6 kbuild: Rename HOSTCFLAGS to KBUILD_HOSTCFLAGS
10844aebf448 kbuild: Rename HOSTCXXFLAGS to KBUILD_HOSTCXXFLAGS
b90a368000ab kbuild: Rename HOSTLDFLAGS to KBUILD_HOSTLDFLAGS
8377bd2b9ee1 kbuild: Rename HOST_LOADLIBES to KBUILD_HOSTLDLIBS
f92d19e0ef9b kbuild: Use HOST*FLAGS options from the command line
4ab3b80159d4 kconfig: check for pkg-config on make {menu,n,g,x}config
693359f7ac90 kconfig: rename SYMBOL_AUTO to SYMBOL_NO_WRITE
f60b992e30ff kbuild: replace $(LDFLAGS) $(ldflags-y) with $(ld_flags)
2fb9279f2c3e kbuild: change ld_flags to contain LDFLAGS_$(@F)
c931d34ea085 arm64: build with baremetal linker target instead of Linux when available
5accd7f3360e kconfig: handle format string before calling conf_message_callback()
a2ff4040151a kconfig: rename file_write_dep and move it to confdata.c
0608182ad542 kconfig: split out useful helpers in confdata.c
adc18acf42a1 kconfig: remove unneeded directory generation from local*config
79123b1389cc kconfig: create directories needed for syncconfig by itself
16952b77d8b5 kconfig: make syncconfig update .config regardless of sym_change_count
d6c6ab93e17f kbuild: remove deprecated host-progs variable
56869d45e364 kconfig: fix the rule of mainmenu_stmt symbol
c151272d1687 kconfig: remove unused sym_get_env_prop() function
1880861226c1 kconfig: remove P_ENV property type
e3fd9b5384f3 scripts/dtc: consolidate include path options in Makefile
4bf6a9af0e91 kconfig: add build-only configurator targets
f1575595d156 kconfig: error out when seeing recursive dependency
5e8c5299d315 kconfig: report recursive dependency involving 'imply'
f498926c47aa kconfig: improve the recursive dependency report
98a4afbfafd2 kconfig: fix "Can't open ..." in parallel build
9a9ddcf47831 kconfig: suppress "configuration written to .config" for syncconfig
87a32e624037 kbuild: pass LDFLAGS to recordmcount.pl
d503ac531a52 kbuild: rename LDFLAGS to KBUILD_LDFLAGS
217c3e019675 disable stringop truncation warnings for now
bc8d2e20a3eb kconfig: remove a spurious self-assignment
fd65465b7016 kconfig: do not require pkg-config on make {menu,n}config
5a4630aadb9a ftrace: Build with CPPFLAGS to get -Qunused-arguments
Note that this adds new cleanup work to do in that we should adapt the
shared library support we have to what is now upstream.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
It has been noticed on MT7628/88 platforms, that booting the RAM image
does not work reliably. Sometimes it works and sometimes not. Debugging
showed that this "might" be a cache related issue as very strange
errors occurred (e.g. output corrupted etc).
This patch adds a cache flush for the complete SDRAM area to the go cmd
before jumping to the entry point for the MIPS architecture. The
complete area is flushed as we don't know at this point, how big the
area of the "application" really is.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Mauro Condarelli <mc5686@mclink.it>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Mauro Condarelli <mc5686@mclink.it>
Cc: Weijie Gao <weijie.gao@mediatek.com>
This patch fixes an stability issue seen on some vcoreiii targets,
which was root caused to a cache inconsistency situation.
The inconsistency was caused by having kuseg pointing to NOR area but
used as a stack/gd/heap area during initialization, while only
relatively late remapping the RAM area into kuseg position.
The fix is to initialize the DDR right after the TLB setup, and then
remapping it into position before gd/stack/heap usage.
Reported-by: Ramin Seyed-Moussavi <ramin.moussavi@yacoub.de>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Allow SoC or board layers with reconfigurable cpu clocks
capabilties to do implementation specific lookups and service
get_tbclk() requests.
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Useful in custom HW designs which have a need to flush dcache
range in a completely non standard way.
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Commit f4dc714aaa ("arm64: Turn u-boot.bin back into an ELF file after
relocate-rela")
introduce REMAKE_ELF option to recreate u-boot.elf from u-boot ->
u-boot.bin + DT -> u-boot.elf.
The best is to ilustrate it from make V=1 output
cat u-boot-nodtb.bin dts/dt.dtb > u-boot-dtb.bin
cp u-boot-dtb.bin u-boot.bin
aarch64-linux-gnu-objcopy -I binary -B aarch64 -O elf64-littleaarch64 u-boot.bin u-boot-elf.o
aarch64-linux-gnu-ld.bfd u-boot-elf.o -o u-boot.elf --defsym="_start"=0x8000000 -Ttext=0x8000000
Last command has no explicit linker script passed that's why toolchain
internal linker script is used.
In Binutils 2.32 case it contains SIZEOF_HEADERS symbol which has changed
behavior by commit
https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=64029e93683a266c38d19789e780f3748bd6a188
which result in situation that program headers has changed from
(xilinx_zynqmp_mini_defconfig)
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000010000 0x00000000fffc0000 0x00000000fffc0000
0x0000000000018918 0x0000000000018918 RW 0x10000
to
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000000000 0x00000000fffb0000 0x00000000fffb0000
0x0000000000028918 0x0000000000028918 RW 0x10000
Xilinx tools like XSDB or Bootgen are using program headers for loading ELF
to the right location and by above binutils change ELF is loaded to
incorrect location.
The patch is explicitly use u-boot-elf.lds (just cat now) for u-boot.elf
recreation which is called when REMAKE_ELF is setup.
By purpose u-boot-elf.lds doesn't contain OUTPUT_FORMAT/OUTPUT_ARCH to be
able to use by all archs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-By: Álvaro Fernández Rojas <noltari@gmail.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function related to timer and most of the timer functions are in
time.h, so move this function there.
Signed-off-by: Simon Glass <sjg@chromium.org>
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is an init function so move it out of the common header. Avoid using
the typedef so that we don't have to include the global_data header file.
Also tidy up the function style in comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this function into the init.h header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Move this function into init.h which seems to be designed for this sort
of thing. Also update the header to declare struct global_data so that it
can be included without global_data.h being needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions do not use driver model but are fairly widely used in
U-Boot. But it is not clear that they will use driver model anytime soon,
so we don't want to label them as 'legacy'.
Move them to a new irq_func.h header file. Avoid the name 'irq.h' since it
is widely used in U-Boot already.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The deadline for migration to CONFIG_DM is v2020.01. The VCT
baords would need an almost complete rewrite of all drivers to
support driver model.
Unless someone has access to the hardware and volunteers to do the migration,
the board should be scheduled for removal.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Some drivers (clk, pinctrl, reset, ...) are necessary for reset of the
system, they should be always selected.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds default eth pinctrl for all boards.
There are two pinctrl nodes used for two scenarios:
ephy_iot_mode - for IOT boards which have only one port (PHY0)
ephy_router_mode - For routers which have more than one ports
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds default p0led status and phy0 link polling for all boards.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
All three UARTs of mt7628 are actually MediaTek's high-speed UARTs which
support baudrate up to 921600.
The high-speed UART is compatible with ns16550 when baudrate <= 115200.
Add compatible string to dtsi file so u-boot can use it when serial_mtk
driver is built in.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The UART of MT7628 has fixed 40MHz input clock so there is no need to put
clock-frequency in every dts files. Just put it into the common dtsi file.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
If configuration is set to skip low level init, automatic
probe of L2 cache size is not performed and the size is set to 0.
Flushing or invalidating the L2 cache will fail in this case.
Add a static configuration (SYS_DCACHE_LINE_SIZE) with default set to 0.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
With commit 06985289d4 ("watchdog: Implement generic watchdog_reset()
version") the init sequence has changed in arch_misc_init(), resulting
in a re-appearance of the d-cache issue on MT7688 boards (e.g. gardena).
When this happens, the first (or sometimes later ones as well) TFTP
command hangs and does not complete correctly. This leads to the
assumption that the d-cache is not in a clean state once the ethernet
driver is called (d-cache is used here for the buffers). The old work-
around with the cache flush somehow does not work any more now with
the new code change.
Unfortunately adding CONFIG_SYS_MALLOC_CLEAR_ON_INIT also did not fix
this issue. With v2019.07-rc3 it shows again. The time of accessing
the data seems to be very important here. It needs to be "very late"
in the boot process.
Testing has shown, that copying a 64KiB area in DDR at a very late
bootup time, directly before calling into the prompt, fixes this issue.
Flushing of the complete d-cache does not seem to necessary, as this
copy alone seems to fix this problem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With commit 06985289d4 ("watchdog: Implement generic watchdog_reset()
version") the init sequence has changed in arch_misc_init(), resulting
in a re-appearance of the d-cache issue on MT7688 boards (e.g. gardena).
When this happens, the first (or sometimes later ones as well) TFTP
command hangs and does not complete correctly. This leads to the
assumption that the d-cache is not in a clean state once the ethernet
driver is called (d-cache is used here for the buffers). The old work-
around with the cache flush somehow does not work any more now with
the new code change.
To fix this issue, this patch now removes the old workaround and selects
CONFIG_SYS_MALLOC_CLEAR_ON_INIT for ARCH_MTMIPS. With this option the
complete malloc area is initialized with zeros (cache lines are touched).
Testing has shown that this also fixes the issue on the MT7688 boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Update device tree for luton to add support for luton pcb90.
This pcb has 24 ports from which 12 ports are connected to
SerDes6G.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Currently mach-mt7620 contains only support for mt7628. To avoid confusion,
rename mach-mt7620 to mach-mtmips, which means MediaTek MIPS platforms.
MT7620 and MT7628 should be distinguished by SOC_MT7620 and SOC_MT7628
because they do not share the same lowlevel codes.
Dependencies of four drivers are changed to SOC_MT7628 as these drivers
are only used by MT7628.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Microsemi SoC defines CONFIG_SYS_SDRAM_BASE to be 0x80000000, which
represents the start of kseg0 and represents a virtual address. Meaning
that the initrd_start and initrd_end point somewhere kseg0.
When these parameters are passed to linux kernel through DT
they are pointing somewhere in kseg0 which is a virtual address but linux
kernel expects the addresses to be physical addresses(in kuseg) because
it is converting the physical address to a virtual one.
Therefore update the uboot to pass the physical address of initrd_start
and initrd_end by converting them using the function virt_to_phys before
setting up the DT.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Remove "select MSCC_BITBANG_SPI_GPIO" since Kbuild option was deleted
back in commit ace9c103df:
commit ace9c103df
Author: Lars Povlsen <lars.povlsen@microchip.com>
Date: Tue Jan 8 10:38:35 2019 +0100
mips: gpio: mscc: Obsoleted gpio-mscc-bitbang-spi.c
Add ethernet nodes for Serval SoCs family. There are 2 pcb in this
family: pcb105 and pcb106.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
In case the ddr training was failing, it couldn't reset, it was just
hanging. Therefore reimplement it, so when ddr training is failing
it would call _machine_restart, which power downs the DDR and does
a force reset.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
This patch tries to implement a generic watchdog_reset() function that
can be used by all boards that want to service the watchdog device in
U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG.
Without this approach, new boards or platforms needed to implement a
board specific version of this functionality, mostly copy'ing the same
code over and over again into their board or platforms code base.
With this new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
This patch also adds a new flag to the GD flags, to flag that the
watchdog is ready to use and adds the pointer to the watchdog device
to the GD. This enables us to remove the global "watchdog_dev"
variable, which was prone to cause problems because of its potentially
very early use in watchdog_reset(), even before the BSS is cleared.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Maxim Sloyko <maxims@google.com>
Cc: Erik van Luijk <evanluijk@interact.nl>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: "Álvaro Fernández Rojas" <noltari@gmail.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Add ethernet nodes for ServalT SoCs family. Currently there is only one
pcb(pcb116) in this family.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Add network driver for Microsemi Ethernet switch.
It is present on ServalT SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add ethernet nodes for Jaguar2 SoCs family. There are 3 pcb in this
family: pcb110, pcb111 and pcb112.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Enable the gpio controllers in the device tree
of the board bcm968380gerg.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add gpio controllers in bcm6838 device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
QCA9563 is CPU used on AP152 board :
Clock speed : 750 MHz ,
Arch : Mips 74Kc,
Eth : SGMII interface,
MIMO config : 3 * 3 450M,
2 * USB 2.0,
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Changes for v2:
- coding style cleanup
- remove ununsed flash chip in defconfig
- enable automatic icache / dcache size in defconfig
Changes for v3:
- add detailed information for qca956x in commit message
Changes for v4:
- remove pre-configured network settings in ap152.h
Changes for v5:
- coding style cleanup
See details in chapter 8.6.2 and 8.6.4 (page 140-141) of qca9563 datasheet,
NFRAC[17:0]
So the mask of [17:5] is 0x1fff not 0x3fff.
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Changes for v2-v3:
- add more information for this commit
Changes for v4-v5:
- coding style cleanup
Remove the function boot_reloc_ramdisk in the file arch/mips/lib/bootm
because it is relocating again the ramdisk. The function do_bootm_states()
already relocates the ramdisk even if it is a legacy uImage or a FIT image.
The relocation in the function do_bootm_states() was introduce in the
commit c2e7e72bb9 ("bootm: relocate ramdisk
if CONFIG_SYS_BOOT_RAMDISK_HIGH set")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch changes Gardena to the correct GARDENA spelling. Also the
platform name is "GARDENA smart Gateway". This patch changes the
incorrect occurrances.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
There is no reason not to use the Linux "jedec,spi-nor" binding in U-Boot
dts files. This compatible has been added in sf_probe, let use it.
This patch switches to jedec,spi-nor when spi-flash is used in the DTS
and DTSI files, and removed spi-flash when jedec,spi-nor is already
present.
The x86 dts are switched in a separate commit since it depends on a change
in fdtdec.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Evgeniy Paltsev <paltsev@synopsys.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Patrick Delaunay <Patrick.delaunay@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch moves all instances of static "watchdog_dev" declarations to
the "data" section. This may be needed, as the BSS may not be cleared
in the early U-Boot phase, where watchdog_reset() is already beeing
called. This may result in incorrect pointer access, as the check to
"!watchdog_dev" in watchdog_reset() may not be true and the function
may continue to run.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Since commit 27cb7300ff ("Ensure device tree DTS is compiled"),
build succeeds irrespective of the correctness of Makefile.
In fact, you can compile any defconfig without adding any entry in
arch/*/dts/Makefile.
I am going to revert that commit, so device tree must be explicitly
listed in Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than
CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the
same script for both SPL and TPL. Add logic to scripts/Makefile.spl to
pass in the right value when preprocessing the script.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add board support and configuration for Jaguar2 SoC family.
The detection of the board type is based on the phy ids.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
As Ocelot, Servalt, Luton and Jaguar2, this family of SoCs are
found in Microsemi Switches solution.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add board support, configuration and DTS for Servalt SoC
family. Currently there is one board in this family.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
As Ocelot, Luton and Jaguar2, this family of SoCs are found
in Microsemi Switches solution.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Set the correct power-up state (default-state) of the green power LED.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add board support and configuration for Jaguar2 SOC family.
The detection of the board type in this family is based on the phy ids.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
