Update serial boot DRAM's Internal RAM, vector table and DRAM in
start.S, serial flash's read status command over SPI and NOR
flash.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Now that we have 3 boards for the MPC512x it turns out that they all
use the very same fixed_sdram() code.
This patch factors out this common code into cpu/mpc512x/fixed_sdram.c
and adds a new header file, include/asm-ppc/mpc512x.h, with some
macros, inline functions and prototype definitions specific to MPC512x
systems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.
The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Current code only sets the PCI vendor id to 0x1014 and
leaved device id to 0x0000.
Ths patch ....
a) uses the correct PCI_VENDOR_ID_IBM macro for this
b) sets the default device ID as stated in the UM to 0x0156
by using PCI_DEVICE_ID_IBM_405GP for this.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves some basic PCI initialisation from the 4xx cpu_init_f()
to cpu/ppc4xx/4xx_pci.c.
The original cpu_init_f() function enabled the 405EP's internal arbiter
in all situations. Also the HCE bit in cpc0_pci is always set.
The first is not really wanted for PCI adapter designs and the latter
is a general bug for PCI adapter U-Boots. Because it enables
PCI configuration by the system CPU even when the PCI configuration has
not been setup by the 405EP. The one and only correct place is
in pci_405gp_init() (see "Set HCE bit" comment).
So for compatibility reasons the arbiter is still enabled in any case,
but from weak pci_pre_init() so that it can be replaced by board specific
code.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
It fixes the access to the 'ehci' struct elements for mpc83xx which
should have been taken care of in 4ef01010aa
Sorry about that.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch makes pll_write on PPC405EP boards
global and callable from C code.
pll_write can be used to dynamically modify the PLB:PCI divider
as it is required for 33/66 MHz pci adapters based on the 405EP.
board_early_init_f() is a good place to do that (check M66EN signal
and call pll_write() when it is required).
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch implements the is_pci_host() function in a similiar way
as it is used on 440 targets.
The former path with CONFIG_PCI_HOST == PCI_HOST_AUTO does not
build on 405EP targets because checking the PCI arbiter is different.
So putting the fixed code into a separate function makes the code
more readable.
Also using is_pci_host() on 405 brings 405 and 440 PCI code
a little bit closer.
In preparation for an upcoming 405EP based PMC module I made this
function weak so that it can be overwritten from board specific code.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a debug compilation error for PPC4xx platforms, all
other architectures are not affected by this change. The 'handler'
pointer was undefined. The fix is exercised and has effect only if
DEBUG is defined.
Signed-off-by: Alessio Centazzo acpatin@yahoo.com
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes printf format string compilation warnings in several
debug statements. It also fixes the dump of DDR controller MQ registers
found on some 44x and 46x platforms. The current register dump code
uses incorrect DCRs to access these registers.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>
all sh boards use the same cpu linker script so move it to cpu/$(CPU)
that could be overwrite in following order
SOC
BOARD
via the corresponding config.mk
tested on r2dplus
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites
timer code, which is now both correct and much smaller. Unused
functions like udelay_masked() have been removed as no driver uses
them, even the ones that are not currently active for this board.
mtu.h is copied literally from the kernel sources.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
There is only one public release of the Nomadik chip, so the ifdef
in reset code as well as a define in the config file are not needed
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
To enable CAN init, CONFIG_CAN has to be defined in the board config file
and at91_can_hw_init() has to be called in the board specific code.
CAN is available on AT91SAM9263 and AT91CAP9 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu>
Tested-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update 83xx architecture's CONFIG_ECC_INIT_VIA_DDRC references to
CONFIG_ECC_INIT_VIA_DDRCONTROLLER, which other Freescale architectures
use
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The calculate for rank density in compute_ranksize() for DDR3 used all
integers for the expression, so the result was also a 32-bit integer, even
though the 'bsize' variable is a u64. Fix the expression to calculate a
true 64-bit value.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also update dmacpy()'s argument order to match memcpy's and use
phys_addr_t/phy_size_t for address/size arguments
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DMA support is now enabled via the CONFIG_FSL_DMA define instead of the
previous CONFIG_DDR_ECC
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Unify with 83xx and 85xx and use CPU_TYPE_ENTRY. We are going to use
this to convey the # of cores and DDR width in the near future so its
good to keep in sync.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Because of the reset_cpu is soc specific, should be move to soc
And read reset value from SYS_ID register instead of hard code
this patch also supports s3c6410
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds the NAND SPL framework needed to boot i.MX31 boards
from NAND.
It has been tested on a i.MX31 PDK board with large page NAND. Small
page NANDs should work as well, but this has not been tested.
Note: The i.MX31 NFC uses a non-standard layout for large page NANDs,
whether this is compatible with a particular setup depends on how
the NAND device is programmed by the flash programmer (e.g. JTAG
debugger).
The patch is based on the work by Maxim Artamonov.
Signed-off-by: Maxim Artamonov <scn1874@yandex.ru>
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Currently CONFIG_ONENAND_IPL is used in a number of #ifdef's
in start.S. In preparation for adding support for NAND SPL
the macro CONFIG_PRELOADER is introducted and replaces the
CONFIG_ONENAND_IPL in start.S.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
The debug tools that interface with the other side of the JTAG console
got much slower when generalizing things, so bump up the default timeout
value on the U-Boot side to cope. Hopefully at some point we can improve
the debug tools to speed things back up.
Signed-off-by: Vivi Li <vivi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Added CONFIG_NET_MULTI to all Davinci boards
Removed all calls to Davinci network driver from board code
Added cpu_eth_init() to cpu/arm926ejs/cpu.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The following changes were made to sync up the DMA code between the 85xx
and 86xx architectures which will make it easier to break out common
8xxx DMA code:
85xx:
- Don't set STRANSINT and SPCIORDER fields in SATR register. These bits
only have an affect when the SBPATMU bit is set.
- Write 0xffffffff instead of 0xfffffff to clear errors in the DMA
status register. We may as well clear all 32 bits of the register...
86xx:
- Add CONFIG_SYS_MPC86xx_DMA_ADDR define to address DMA registers
- Add clearing of errors in the DMA status register when initializing
the controller
- Clear the channel start bit in the DMA mode register after a transfer
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Break out DMA structures for the Freescale MPC85xx and MPC86xx cpus to
reduce a large amount of code duplication
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The uec driver contains code to hard code configuration information for the uec
ethernet controllers. This patch creates an array of uec_info structures, which
are then parsed by the corresponding driver instance to determine configuration.
It also creates function uec_standard_init() to initialize all UEC interfaces
for 83xx and 85xx.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Acked-by: Timur Tabi <Timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Its reasonable that we may have ethernet devices but dont have drivers
or support enabled for them in u-boot and want the device tree fixed up.
Unconditionally calling the ethernet fixup is fine since if we dont have
ethernet nodes that match (or aliases) we will not attempt to do
anything.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Timur Tabi <timur@freescale.com>
This is needed for the upcoming esd MECP5123 board port which uses
I2C EEPROM for environment storage.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Acked-by: Heiko Schocher<hs@denx.de>
The following patch reorganizes/reworks the USB support for mpc83xx
as under:-
* Moves the 83xx USB clock init from drivers/usb/host/ehci-fsl.c to
cpu/mpx83xx/cpu_init.c
* Board specific usb_phy_type is read from the environment
* Adds USB EHCI specific structure in include/usb/ehci-fsl.h
* Copyrights revamped in most of the following files
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Use the standard lowercase "x" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Use the standard lowercase "xx" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch removes the duplicated code for baudrate generator configuration
in the PSC serial_init() implementation by calling serial_setbrg() instead
of duplicating the code.
Signed-off-by: Stefan Roese <sr@denx.de>
The wrong input frequency was used in serial_setbrg(). This patch fixes
this by using ips_clk as input frequency for the PSC baudrate generator.
Signed-off-by: Stefan Roese <sr@denx.de>
Move needed definitions (register descriptions etc.) from
include/mpc512x.h into include/asm-ppc/immap_512x.h.
Instead of using a #define'd register offset, use a function that
provides the PATA controller's base address.
All the rest of include/mpc512x.h are register offset definitions
which can be eliminated by proper use of C structures.
There are only a few register offsets remaining that are needed in
cpu/mpc512x/start.S; for these we provide cpu/mpc512x/asm-offsets.h
which is intended as a temporary workaround only. In a later patch
this file will be removed, too, and then auto-generated from the
respective C structs.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
This commit changes the MPC512x code to use I/O accessor calls (i.e.
out_*() and in_*()) instead of using deprecated pointer accesses.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
We will soon see several new MPC521x based boards added. This patch
moves files that are not board specific to a common directory so they
can be shared by all such ports. It also splits off common IDE code
into a new file, cpu/mpc512x/ide.c .
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Many of the help messages were not really helpful; for example, many
commands that take no arguments would not print a correct synopsis
line, but "No additional help available." which is not exactly wrong,
but not helpful either.
Commit ``Make "usage" messages more helpful.'' changed this
partially. But it also became clear that lots of "Usage" and "Help"
messages (fields "usage" and "help" in struct cmd_tbl_s respective)
were actually redundant.
This patch cleans this up - for example:
Before:
=> help dtt
dtt - Digital Thermometer and Thermostat
Usage:
dtt - Read temperature from digital thermometer and thermostat.
After:
=> help dtt
dtt - Read temperature from Digital Thermometer and Thermostat
Usage:
dtt
Signed-off-by: Wolfgang Denk <wd@denx.de>
The kernel stores address<->symbol names in it so things can be decoded at
runtime. Do it in U-Boot, and we get nice symbol decoding when crashing.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The function and interface clocks for each GPIO bank, except the first, must
be explicitly turned on. These are controlled by the config level defines
CONFIG_OMAP3_GPIO_n where n is from 2 to 6.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
all arm init the IRQ stack the same way
so unify it in lib_arm/interrupts.c and then call arch specific interrupt init
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
all arm boards except a few use the same cpu linker script
so move it to cpu/$(CPU)
that could be overwrite in following order
SOC
BOARD
via the corresponding config.mk
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Once the Davinci watchdog has been enabled, the timeout
value cannot be changed. If the timeout in use is long,
it can take a long time for card to reset. By writing
an invalid service key, we can trigger an immediate reset.
Signed-off-by: Thomas Lange <thomas@corelatus.se>
Port version 2.6.27 of the linux kernel's omap gpio interface to u-boot.
The orignal source is in linux/arch/arm/plat-omap/gpio.c
See doc/README.omap3 for instructions on use.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
The u-boot.lds is common for all DaVinci boards. The patch removes
multiple instances and moves the u-boot.lds to /cpu/arm926ejs/davinci
folder. This addresses one of the comments i received while submitting
patches for DM3xx
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The u-boot.lds file is common for all omap boards.
Move a cleaned up version to the cpu layer and add makefile logic to use it.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Move the clock-rate dumping code into the cpu/.../davinci area
where it should have been, enabled by CONFIG_DISPLAY_CPUINFO,
updating the format and showing the DSP clock (where relevant).
Switch boards to use the cpuinfo() hook for this stuff.
Remove a few now-obsolete PLL #defines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
actually the timer init use the interrupt_init as init callback
which make the interrupt and timer implementation difficult to follow
so now rename it as int timer_init(void) and use interrupt_init for interrupt
btw also remane the corresponding file to the functionnality implemented
as ixp arch implement two timer - one based on interrupt - so all the timer
related code is moved to timer.c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Remove duplicated interrupt code. Original, identical code can be found
in lib_arm/interrupts.c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Add some basic declarations for DaVinci DM355/DM350/DM335 support,
keyed on CONFIG_SOC_DM355. (DM35X isn't quite right because the
DM357 is very different; while the DM355 is like a DM355 without
the MPEG/JPEG coprocessor).
These have different peripherals than the DM6446, and some of
the peripherals are at different addresses. Notably for U-Boot,
there's no EMAC, and the NAND controller address is different
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fix two buglets in the dm644x support: don't set two must-be-zero
bits in the UART management register; and only include the I2C hooks
if the I2C driver is being included.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Split out DaVinci DM6446-specific bits from more generic bits:
- Add a CONFIG_SOC_DM644X. All current boards use DM6446 chips;
DM6443 and DM6441 chips differ in available peripherals.
- Move most DM644X-specific bits from psc.c to a new dm644x.c file,
which is conditionally built. It provides device-specific setup.
Plus minor coding style and comment updates with respect to the PSC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Update cpu/arm926ejs/davinci/Makefile to use COBJ-y type syntax.
Add the first conditional: for EMAC driver support. Not all
chips have an EMAC; and boards might not use it, anyway.
This doesn't touch PHY configuration; that should eventually
become conditional too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Move DaVinci PSC support from board/* to cpu/* where it belongs.
The PSC module manages clocks and resets for all DaVinci-family
SoCs, and isn't at all board-specific.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Don't needlessly include lowlevel init code; that's only really
needed with boot-from NOR (not boot-from-NAND). The 2nd stage
loader (UBL) handles that before it loads U-Boot.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch adds another build target for the AMCC Sequoia PPC440EPx
eval board. This RAM-booting version is targeted for boards without
NOR FLASH (NAND booting) which need a possibility to initially
program their NAND FLASH. Using a JTAG debugger (e.g. BDI2000/3000)
configured to setup the SDRAM, this debugger can load this RAM-
booting image to the target address in SDRAM (in this case 0x1000000)
and start it there. Then U-Boot's standard NAND commands can be
used to program the NAND FLASH (e.g. "nand write ...").
Here the commands to load and start this image from the BDI2000:
440EPX>reset halt
440EPX>load 0x1000000 /tftpboot/sequoia/u-boot.bin
440EPX>go 0x1000000
Please note that this image automatically scans for an already
initialized SDRAM TLB (detected by EPN=0). This TLB will not be
cleared. This TLB doesn't need to be TLB #0, this RAM-booting
version will detect it and preserve it. So booting via BDI2000
will work and booting with a complete different TLB init via
U-Boot works as well.
Signed-off-by: Stefan Roese <sr@denx.de>
New default, weak i2c_get_bus_speed() and i2c_set_bus_speed() functions
replace a number of architecture-specific implementations.
Also, providing default functions will allow all boards to enable
CONFIG_I2C_CMD_TREE. This was previously not possible since the
tree-form of the i2c command provides the ability to display and modify
the i2c bus speed which requires i2c_[set|get]_bus_speed() to be
present.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Many boards/controllers/drivers don't support an I2C slave interface,
however CONFIG_SYS_I2C_SLAVE is used in common code so provide a
default
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The ddr code computes most things as 64-bit quantities and had some places
in the middle that it was using phy_addr_t and phys_size_t.
Instead we use unsigned long long through out and only at the last stage of
setting the LAWs and reporting the amount of memory to the board code do we
truncate down to what we can cover via phys_size_t.
This has the added benefit that the DDR controller itself is always setup
the same way regardless of how much memory we have. Its only the LAW
setup that limits what is visible to the system.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MAXSIZE field in the TLB1CFG register is 4 bits, not 8 bits.
This made setup_ddr_tlbs() try to set up a TLB larger than the e500 maximum
(256 MB)
which made u-boot hang in board_init_f() when trying to create a new stack
in RAM.
I have an mpc8540 with one 1GB dimm.
Signed-off-by: Fredrik Arnerup <fredrik.arnerup@edgeware.tv>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
This patch now uses the correct ECC byte order (Smart Media - SMC)
to be used on the 4xx NAND FLASH driver. Without this patch we have
incompatible ECC byte ordering to the Linux kernel NDFC driver.
Please note that we also have to enable CONFIG_MTD_NAND_ECC_SMC in
drivers/mtd/nand/nand_ecc.c for correct operation. This is done with
a seperate patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
This patch moves the definition for the PPC4xx NAND FLASH controller
(NDFC) CONFIG_NAND_NDFC into include/ppc4xx.h. This is needed for the
upcoming fix for the ECC byte ordering of the NDFC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
The timer_init() function was not using the right csync instruction, nor
was it doing it right after disabling the core timer.
The timer_reset() function would reset the timestamp, but not the actual
timer, so there was a common edge case where get_timer() return a jump of
one timestamp (couple milliseconds) right after resetting. This caused
many functions to improperly timeout right away.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Implement ethernet halt() by putting MAC0 in reset.
If we do not do this, we will get memory corruption
when ethernet frames are received during early OS boot.
Signed-off-by: Thomas Lange <thomas@corelatus.se>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
This patch fixes a problem in the CPU frequency calculation. Without it
a 798MHz CPU is displayed as 368.503 MHz. And with it it's 798 MHz.
Signed-off-by: Stefan Roese <sr@denx.de>
cpu/mpc8260/cpu.c used to use do_fixup_by_path_u32() to update the
clock frequencies in the device tree, using a CPU path
"/cpus/OF_CPU", with OF_CPU beind defined in the board config file.
However, this does not work when one board config file (here:
MPC8260ADS.h) is intended to be used for several diffrent CPUs and
therefor contains a generic definition like "cpu@0", as the device
trees that will then be loaded will contain specific names like
"PowerPC,8272@0".
We switch to using do_fixup_by_prop_u32() instead, so we can search
for device_type="cpu", as it is done in other architectures, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
AFEB9260 uses PA10, PA11 for ETX2 and ETX3.
Also, due to extarnal pull-up on IRQ line, Micrel PHY ID is 1 after reset sequence,
not 0.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
When the clock functions were changed to use cached values (and thereby
avoiding expensive math functions), early serial debug broke because the
baud programming is called before external memory is available.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When dropping jump block support, the assumption was that all bootroms
supported entry point redirection via the EVT1 register. Unfortunately,
this turned out to be incorrect for the oldest Blackfin parts (BF533-0.2
and older and BF561). No one really noticed earlier because these parts
usually are booted by bypassing the bootrom entirely, and older BF533
parts are not supported at all (too many anomalies).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure we recurse through serial_putc() rather than bang on the UART
transmit register directly to avoid hardware overflows when using \n.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
lowlevel_init.S is not used any more so remove it.
As consequence, we also don't have to generate u-boot.lds
but can use a static version as before.
This also fixes the out-of-tree build problem introduced
with commit f0a2c7b4 "at91: add support for the PM9263 board"
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Let CONFIG_SYS_HZ to have value of 1000 effectively fixing all users of
get_timer.
Changes since original version:
* Set PTV=2 (divisor 8) for boards using 12MHz timer clock source to
improve timer resolution.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
The function display_board_info() displays incorrect
silicon revision - based on the return value from
function get_cpu_rev().
This patch fixes the problem.
Signed-off-by: Sanjeev Premi <premi@ti.com>
The board-types defined in struct omap3_sysinfo seem to be
unused. The function display_board_info() is passed
board type as an argument; which is ignored.
This patch removes all uses of board-type, related definitions
and functions.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Use the functions print_cpuinfo() and checkboard() to
display the cpu and board specific information.
These functions reuse content from the existing function
display_board_info() - which has been removed.
Also, updated the existig OMAP3 configurations to
define:
- CONFIG_DISPLAY_CPUINFO
- CONFIG_DISPLAY_BOARDINFO
Signed-off-by: Sanjeev Premi <premi@ti.com>
__asm__ follows gcc's documented syntax and is generally more common
than __asm. This change is only asthetic and should not affect
functionality.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
__attribute__ follows gcc's documented syntax and is generally more
common than __attribute. This change is only asthetic and should not
affect functionality.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
if using CONFIG_BOOTCOUNT_LIMIT feature on a MPC8360 CPU
in the muram-data node, the reg entry needs to be updated.
This is done in fdt_fixup_muram(), but we should use
the compatible "fsl,qe-muram-data" for searching the
node instead of searching the muram-data node with
an absolute path.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The timer has been rewrote with a precision at ~0,18%
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Sergey Lapin <slapin@ossfans.org>
Tested-by: Eric BENARD <ebenard@free.fr>
The PM9263 board is based on the AT91SAM9263-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9263.html
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This additional text in the bootup log helps to see if the board is
configured for NAND-booting. Especially helpful for boards that can
boot from NOR and NAND (e.g. most of the AMCC eval boards).
Signed-off-by: Stefan Roese <sr@denx.de>
There is no code change here, just new comments, but this keeps me from
having to do another audit from scratch in the future.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
DESCRIPTION:
The column address width settings for banks 2 and 3 are misconnected in
the SDRAM controller. Accesses to bank 2 will result in an error if the
Column Address Width for bank 3 (EB3CAW ) is not set to be the same as
that of bank 2.
WORKAROUND:
If using bank 2, make sure that banks 2 and 3 have the same column address
width settings in the EBIU_SDBCTL register. This must be the case
regardless of whether or not bank 3 is enabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
DESCRIPTION:
If the DF bit is set prior to a hardware reset, the PLL will continue to
divide CLKIN by 2 after the hardware reset, but the DF bit itself will be
cleared in the PLL_CTL register.
WORKAROUND:
Reprogram the PLL with DF cleared if the desire is to not divide CLKIN by
2 after reset.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
DESCRIPTION:
The Boot ROM is executed at power up/reset and changes the value of the
SICA_IWR registers from their default reset value of 0xFFFF, but does not
restore them.
WORKAROUND:
User code should not rely on the default value of these registers. Set
the desired values explicitly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The previous code waited 1000us before checking i2c
status. Measurement shows i2c is usually ready in
under 50us. Change the polling interval to 15us,
loop 6,667 times to keep the polling timeout constant
at 100ms.
Fixes this compile error:
board.c: In function 'do_switch_ecc':
board.c:339: error: 'cmd_tbl_t' has no member named 'help'
make[1]: *** [board.o] Error 1
make[1]: Leaving directory `/db/psp_git/users/a0756819/u-boot/cpu/arm_cortexa8/omap3'
make: *** [cpu/arm_cortexa8/omap3/libomap3.a] Error 2
This is due to the fact that current command uses long
help for the usage print even if the CONFIG_SYS_LONGHELP
is not enabled. (Thanks Jean-Christophe for explanation).
Signed-off-by: Sanjeev Premi <premi@ti.com>
Move machine specific code to smdk6400.
Some board use OneNAND instead of NAND.
Some register MP0_CS_CFG[5:0] are controled by both h/w and s/w.
So it's better to use macro instead of hard-coded value.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
