2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-12-24 20:13:39 +00:00
Commit graph

290 commits

Author SHA1 Message Date
Andre Przywara
beeace9ba1 sunxi: refactor serial base addresses to avoid asm/arch/cpu.h
At the moment we have each SoC's memory map defined in its own cpu.h,
which is included in include/configs/sunxi_common.h. This will be a
problem with the introduction of Allwinner RISC-V support.

Remove the inclusion of that header file from the common config header,
instead move the required serial base addresses (for the SPL) into a
separate header file. Then include the original cpu.h file only where
we really need it, which is only under arch/arm now.

This disentangles the architecture specific header files from the
generic code.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2023-10-22 23:41:52 +01:00
Andre Przywara
eb53e7743c sunxi: h616: lower SPL stack address to avoid BROM data
When using the USB OTG FEL mode on the Allwinner H616, the BootROM
stores some data at the end of SRAM C. This is also the location where
we place the initial SPL stack, so it will overwrite this data.
We still need the BROM code after running the SPL, so should leave that
area alone.
Interestingly this does not seem to have an adverse effect, I guess on
the "way out" (when we return to FEL after the SPL has run), this data
is not needed by the BROM, for just the trailing end of the USB operation.
However this is still wrong, and we should not clobber BROM data.

Lower the SPL stack address to be situated right below the swap buffers
we use in sunxi-fel: that should be out of the way of everyone else.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
2023-01-21 01:32:23 +00:00
Tom Rini
0478dac62a kbuild: Remove uncmd_spl logic
At this point in the conversion there should be no need to have logic to
disable some symbol during the SPL build as all symbols should have an
SPL counterpart.

The main real changes done here are that we now must make proper use of
CONFIG_IS_ENABLED(DM_SERIAL) rather than many of the odd tricks we
developed prior to CONFIG_IS_ENABLED() being available.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-23 10:15:13 -05:00
Tom Rini
0613c36a7a global: Migrate CONFIG_EXTRA_ENV_SETTINGS to CFG
Perform a simple rename of CONFIG_EXTRA_ENV_SETTINGS to CFG_EXTRA_ENV_SETTINGS

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-23 10:09:42 -05:00
Tom Rini
32b7e39db4 Convert CONFIG_STANDALONE_LOAD_ADDR to Kconfig
This converts the following to Kconfig:
   CONFIG_STANDALONE_LOAD_ADDR

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-22 10:31:48 -05:00
Tom Rini
14f43797d0 Prepare v2023.01-rc4
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAmOgaw0ACgkQFHw5/5Y0
 tyxIeQv8DfAAB8hN+wWeDhQAJBXBLvV+RrocGJ2lpuWN0DUgT955l0zSjP4eD5I/
 sSsT8iJ15obkbWHq61V9W81Velw5qR+gHW9IAzFKiQBfvdcdfgWFeme9fWp/gqxn
 vvPc2sULA9utkc+kQ+qJy2hmTM7I0ZbKzUwTXSv+Tp9on3vlc0quKSHiZ1EvHNww
 8tW13d1r+Be+CC+GVPrhJojfKBcYVJhW21rJMgb4JdfGNWKmpUpF6fUzHe0wiy2P
 HSnScr44E099t9RDZabw0V1fEgQqxIAmL1qQamXf9ddLZQM9Sq63lygTtGsqg61+
 qeHCZVjPg9cXayGfRVesH8sko3vW+IPuo0Q6Ox0vAyRSyzTpOcTuzn3RcMrq+mfu
 ZRF32aFJKVvAI3xesOj1aCBBYjl4POiHA8i3yeP9KcjqW3So0aphDtxp1idgwOZl
 kIxuC4ItWyF7xoyng/7RWwr2VjcKSyw58stRjfV+WNcByV4+ud1A59vsgZOqO49m
 0bLx5dGu
 =EX/F
 -----END PGP SIGNATURE-----

Merge tag 'v2023.01-rc4' into next

Prepare v2023.01-rc4

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-21 13:09:01 -05:00
Andre Przywara
ed82586c40 sunxi: remove unused CONFIG_MMC_SUNXI_SLOT
There is a CONFIG_MMC_SUNXI_SLOT definition in our sunxi_common.h config
header, which was used to note the first MMC controller to initialise.
The definition in that header was always set to 0, with no easy way of
overriding this, and certainly none of the existing boards made any use
of that (non-)feature.
Remove that definition and replace it with a constant 0 in the only
user, in board.c. It turns out that this is safe, as this is only used
in the SPL, and the BROM also unconditionally initialises MMC0.
This also removes the last legacy config symbol with SUN*I in it from
the whitelist.

Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-12-14 22:31:06 +00:00
Tom Rini
65cc0e2a65 global: Move remaining CONFIG_SYS_* to CFG_SYS_*
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-12-05 16:06:08 -05:00
Tom Rini
aa6e94deab global: Move remaining CONFIG_SYS_SDRAM_* to CFG_SYS_SDRAM_*
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-12-05 16:06:07 -05:00
Tom Rini
91092132ba global: Move remaining CONFIG_SYS_NS16550_* to CFG_SYS_NS16550_*
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NS16550
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-12-05 16:06:07 -05:00
Tom Rini
9591b63531 Convert CONFIG_SYS_NS16550_MEM32 et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_NS16550_MIN_FUNCTIONS
   CONFIG_SYS_NS16550_MEM32
   CONFIG_SYS_NS16550_PORT_MAPPED
   CONFIG_SYS_NS16550_REG_SIZE
   CONFIG_SYS_NS16550_SERIAL

To do this we also introduce CONFIG_SPL_SYS_NS16550_SERIAL so that
platforms can enable the legacy driver here for SPL.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-05 16:06:07 -05:00
Tom Rini
4d3495deb6 Convert CONFIG_SYS_NAND_MAX_OOBFREE et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_NAND_MAX_OOBFREE
   CONFIG_SYS_NAND_MAX_ECCPOS

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-12-05 16:05:38 -05:00
Tom Rini
08574ed339 Convert CONFIG_SYS_MONITOR_LEN to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_MONITOR_LEN

To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-11-10 10:08:55 -05:00
Tom Rini
9ba938e744 Convert CONFIG_SYS_MMC_MAX_DEVICE to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_MMC_MAX_DEVICE

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2022-11-10 10:08:55 -05:00
Tom Rini
a918df21f0 Convert CONFIG_SYS_MAX_NAND_DEVICE to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_MAX_NAND_DEVICE

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-11-10 10:08:54 -05:00
Simon Glass
b86986c7b3 video: Rename CONFIG_DM_VIDEO to CONFIG_VIDEO
Now that all the old code is gone, rename this option. Driver model
migration is now complete.

Signed-off-by: Simon Glass <sjg@chromium.org>
2022-10-30 20:07:17 +01:00
Andre Przywara
c8b9ba4bb2 sunxi: fix 32MB load address layout
The default load addresses for the various payloads (kernel, DT,
ramdisk) on systems with just 32MB of DRAM have some issues:
For a start the preceding comment doesn't match the actual values:
apparently they were copied from the 64MB S3 layout, then halved, but
since 0x5 is NOT the half of 0x10, they don't match up.
Also those projected maximum sizes are quite restrictive: it's not easy
to build a compressed kernel image with just 4MB. The only defconfig in
mainline Linux that supports the F1C100s (the only 32MB user so far)
creates a 6MB compressed / 15MB uncompressed kernel.
Rearrange the default load addresses to accommodate such a kernel: we
allow an 7MB/16MB kernel, and up to 5MB of ramdisk, stuffing the smaller
binaries like the DTB towards the end, just before the relocated U-Boot.
Shrink the size for DTB and scripts on the way, there is no need for
allowing up to 512K for them.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
2022-10-19 14:15:02 +01:00
Andre Przywara
1bf98bd4e2 sunxi: Kconfig: introduce SUNXI_MINIMUM_DRAM_MB
Traditionally we assumed that every Allwinner board would come with at
least 256 MB of DRAM, and set our DRAM layout accordingly. This affected
both the default load addresses, but also U-Boot's own address
expectations (like being loaded at 160 MB).

Some SoCs come with co-packaged DRAM, but only provide 32 or 64MB. So
far we special-cased those *chips*, as there was only one chip per DRAM
size. However new chips force us to take a more general approach.

Introduce a Kconfig symbol, which provides the minimum DRAM size of the
board. If nothing else is specified, we use 256 MB, and default to
smaller values for those co-packaged SoCs.
Then select the different DRAM maps according to this new symbol, so
that different SoCs with the same DRAM size can share those definitions.

Inspired by an idea from Icenowy.

This is just refactoring: compiled for all boards before and after this
patch: the binaries were identical.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
2022-10-19 14:15:02 +01:00
Tom Rini
c45568cc4e Convert CONFIG_SYS_BOOTM_LEN to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_BOOTM_LEN

As part of this, rework error handling in boot/bootm.c so that we pass
the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not
be available to host tools but we do know the size that we passed to
malloc().

Cc: Soeren Moch <smoch@web.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-07 14:01:09 -04:00
Tom Rini
cd6a45a41f Convert CONFIG_USB_OHCI_NEW et al to Kconfig
This converts the following to Kconfig:
    CONFIG_SYS_OHCI_SWAP_REG_ACCESS
    CONFIG_SYS_USB_OHCI_CPU_INIT
    CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS
    CONFIG_SYS_USB_OHCI_SLOT_NAME
    CONFIG_USB_ATMEL
    CONFIG_USB_ATMEL_CLK_SEL_PLLB
    CONFIG_USB_ATMEL_CLK_SEL_UPLL
    CONFIG_USB_OHCI_LPC32XX
    CONFIG_USB_OHCI_NEW

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-07 09:29:08 -04:00
Tom Rini
a331017c23 Complete migration of MTDPARTS_DEFAULT / MTDIDS_DEFAULT, include in environment
- Ensure that everyone setting mtdids= and mtdparts= is doing so via the
  CONFIG options.
- If the CONFIG options are set, ensure that the default environment
  sets mtdparts / mtdids.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-28 17:11:49 -04:00
Tom Rini
910feb50d4 Globally remove most CONFIG_SPL_BUILD tests from config headers
With the exception of how PowerPC handles SPL and TPL (which has its own
issues), we cannot safely hide options under CONFIG_SPL_BUILD.  Largely
remove the places that have this test today.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-28 17:11:48 -04:00
Tom Rini
aca1f6789a Convert CONFIG_LBA48 et al to Kconfig
This converts the following to Kconfig:
   CONFIG_LBA48
   CONFIG_SYS_64BIT_LBA

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-28 17:03:32 -04:00
Tom Rini
6600b355c7 Convert CONFIG_SPL_BSS_START_ADDR to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_BSS_START_ADDR

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:28 -04:00
Tom Rini
f113d7d303 Convert CONFIG_SPL_STACK to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_STACK

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:27 -04:00
Tom Rini
eaf6ea6a1d Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.h
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
  pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
  set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
  GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
  board config header files.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:19 -04:00
Tom Rini
9b5f9aeb3b Convert CONFIG_SPL_BSS_MAX_SIZE et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_BSS_MAX_SIZE
   CONFIG_SPL_MAX_FOOTPRINT

Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:10 -04:00
Tom Rini
ca8a329a1b Convert CONFIG_SPL_PAD_TO et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_PAD_TO
   CONFIG_SPL_MAX_SIZE
   CONFIG_TPL_PAD_TO
   CONFIG_TPL_MAX_SIZE

Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:06 -04:00
Tom Rini
d31466b382 Convert CONFIG_SYS_CBSIZE to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_CBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:00 -04:00
Tom Rini
d0ee7f295d Convert CONFIG_SYS_PBSIZE to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_PBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:00 -04:00
Peng Fan
c5b9bf5518 include/configs: drop COUNTER_FREQUENCY
Since we have CONFIG_COUNTER_FREQUENCY enabled, no need COUNTER_FREQUENCY

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-21 15:27:17 -04:00
Tom Rini
95b641756c Convert CONFIG_BOARD_SIZE_LIMIT to Kconfig
This converts the following to Kconfig:
   CONFIG_BOARD_SIZE_LIMIT

To do this, introduce CONFIG_HAS_BOARD_SIZE_LIMIT.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 09:05:19 -04:00
Tom Rini
b3fe015893 sunxi: Do not define CONFIG_SPL_STACK_ADDR_R
We cannot define a CONFIG value here to ensure that the Kconfig value
isn't set wrong.

Fixes: 2c699fe0d3 ("configs: sunxi: Add common SUNIV header")
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18 08:43:24 -04:00
Icenowy Zheng
2c699fe0d3 configs: sunxi: Add common SUNIV header
Adds support for SUNIV and the F1C100s.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-02-04 00:09:57 +00:00
Andre Przywara
f2c33699d1 sunxi-common.h: remove pointless #ifdefs
Remove some pointless #ifdefs from this file, as there are quite too
many of them already.

Some definitions don't really hurt to have in any case, so remove the
pointless CONFIG_MMC guard around CONFIG_MMC_SUNXI_SLOT.

The BOARD_SIZE_LIMIT applies regardless of ARM64 or not (now), so remove
that guard as well. The maximum number of MMC devices does not depend on
CONFIG_ENV_IS_IN_MMC, so move that out to simplify the file.

Last but not least CONFIG_SPL_BOARD_LOAD_IMAGE serves no real purpose
anymore: it's unconditionally defined for all sunxi boards, and protects
nothing applicable outside of sunxi code anymore. Just remove it.

Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-02-04 00:09:57 +00:00
Tom Rini
1616626417 Convert CONFIG_SPL_DRIVERS_MISC et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_DRIVERS_MISC
   CONFIG_SPL_ENV_SUPPORT
   CONFIG_SPL_GPIO
   CONFIG_SPL_I2C
   CONFIG_SPL_LDSCRIPT
   CONFIG_SPL_LIBCOMMON_SUPPORT
   CONFIG_SPL_LIBGENERIC_SUPPORT
   CONFIG_SPL_LOAD_FIT_ADDRESS
   CONFIG_SPL_MMC
   CONFIG_SPL_NAND_SUPPORT
   CONFIG_SPL_NO_CPU_SUPPORT
   CONFIG_SPL_OS_BOOT
   CONFIG_SPL_POWER
   CONFIG_SPL_STACK_R
   CONFIG_SPL_STACK_R_ADDR
   CONFIG_SPL_WATCHDOG
   CONFIG_SPL_TEXT_BASE

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-05 11:26:29 -04:00
Samuel Holland
2421497cb7 sunxi: video: Convert panel I2C to use DM_I2C
Two displays supported by the sunxi display driver (each one used by a
single board) require initialization over I2C. Both previously used
i2c_soft; replace this with the i2c-gpio instance that already exists in
those boards' device trees (sun5i-a13-utoo-p66 and sun6i-a31-colombus).

Since the i2c-gpio nodes are not referenced by any other node in the
device trees (the device trees have no panel node), the I2C bus is
selected by its node name.

This panel initialization code was the only i2c_soft user, so the
i2c_soft GPIO setup code can be removed now as well.

Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12 11:01:17 +01:00
Tom Rini
c0ad62c5f7 Convert CONFIG_SYS_NAND_ONFI_DETECTION to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_NAND_ONFI_DETECTION

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-06 09:16:23 -04:00
Tom Rini
5f588f831b arm: Finish migration of CONFIG_MACH_TYPE
As this is only useful when booting with ATAGs, which are now largely
disabled, remove this value for the remaining platforms.  We have a few
places in the code that had been testing for MACH_TYPE as a sort of
internal logic.  Update those to use different but still correct CONFIG
symbols.

Cc: Phil Sutter <phil@nwl.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-07 19:17:32 -04:00
Tom Rini
9774462e34 arm: Disable ATAGs support
With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support.  A large number of platforms had enabled
support but never supported a kernel so old as to require it.  Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years.  This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user.  When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts.  In other cases, these
functions were simply unused, so drop them.

Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-07 16:22:30 -04:00
Tom Rini
7cfbba36e9 Convert CONFIG_SYS_MALLOC_LEN to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_MALLOC_LEN

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
2021-08-31 17:47:49 -04:00
Tom Rini
49c8ef0e45 Convert CONFIG_SYS_LOAD_ADDR to Kconfig
Now that we have consistent usage, migrate this symbol to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
2021-08-31 17:46:37 -04:00
Tom Rini
a5752f8a25 Convert CONFIG_SYS_I2C_SPEED et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_I2C_SPEED
   CONFIG_SYS_I2C_SLAVE

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30 14:10:07 -04:00
Tom Rini
55dabcc8f2 Convert CONFIG_SYS_I2C_LEGACY to Kconfig and add CONFIG_[ST]PL_SYS_I2C_LEGACY
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig.  Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL.  Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support.  Convert all of the existing users to
one or more symbols.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30 14:10:07 -04:00
Tom Rini
2656145224 Convert CONFIG_SYS_I2C_MVTWSI to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_I2C_MVTWSI

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30 14:10:06 -04:00
Tom Rini
de69572569 Convert CONFIG_SYS_I2C_SOFT et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_I2C_SOFT
   CONFIG_SYS_I2C_SOFT_SPEED
   CONFIG_SYS_I2C_SOFT_SLAVE

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30 14:10:06 -04:00
Simon Glass
69d9eda4da i2c: Rename CONFIG_SYS_I2C to CONFIG_SYS_I2C_LEGACY
It is quite confusing that CONFIG_SYS_I2C selects the legacy I2C and
CONFIG_DM_I2C selects the current I2C. The deadline to migrate I2C is less
than a year away.

Also we want to have a CONFIG_I2C for U-Boot proper just like we have
CONFIG_SPL_I2C for SPL, so we can simplify the Makefile rules.

Rename this symbol so it is clear it is going away.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-28 14:29:37 -04:00
Arnaud Ferraris
747c2421c6 sunxi: arm64: Add addresses for compressed kernel load
The "booti" command to load arm64 Linux kernels supports automatic
decompression of zipped kernel images, but relies on some environment
variables to point to usable buffer RAM.

Add those variables and let them point to some default values, that
should cover most use-cases.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-04-16 01:12:59 +01:00
Jernej Skrabec
17d6eceab5 sunxi: add fdtoverlay_addr_r environment variable
Commit 69076dff22 ("cmd: pxe: add support for FDT overlays") added
support for loading DT overlay files to PXE boot. However, it needs
additional environment variable which points to memory location which
can be used to temporary store overlay data.

Add it and in the process unify alignment using spaces and fix comment.

Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-04-16 01:12:58 +01:00
Jagan Teki
5d235324ae video: sunxi_display: Convert to DM_VIDEO
DM_VIDEO migration deadline is already expired, but around
80 Allwinner boards are still using video in a legacy way:

===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Convert the legacy video driver over to the DM_VIDEO framework. This is
a minimal conversion: it doesn't use the DT for finding its resources,
nor does it use DM clocks or DM devices for the outputs (LCD, HDMI, CVBS).

Tested in Bananapi M1+ Plus 1920x1200 HDMI out. (Jagan)

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Andre: rebase and smaller fixes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-03-03 10:03:15 +01:00