Remove the recommended MAC address from the network card.
NanoPi R4S has a EEPROM attached to the 2nd I2C bus (U92), which stores the MAC address.
Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The host-index-min property is invalid,
so it inherits from the sdmmc definition in dtsi.
Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Correct the LEDS label name and remove the board type prefix,
which is actually unnecessary here, removes the redefined system status LED pin.
Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This enable hs400 and SDMA support for emmc on evb-rk3399.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds support for the RK3568 platform to this driver.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add clock, phy and other configuration, it is convenient to support
new controller. Here a short summary of the changes:
- Add mmc_of_parse to parse dts config.
- Remove OF_PLATDATA related code.
- Reorder header inclusion.
- Add phy ops.
- add ops set_ios_post to modify the parameters of phy when the
clock changes.
- Add execute tuning api for hs200 tuning.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Both rk3xxx.dtsi and rk3188.dtsi have recently
had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3188-radxarock-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Both rk3xxx.dtsi and rk3188.dtsi have recently
had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3188-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to update the DT for rk3188
sync the power domain dt-binding header.
This is the state as of v5.12 in Linux.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. This file has recently had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3xxx-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to update the DT for rk3066 and rk3188
sync the clock dt-binding header.
This is the state as of v5.12 in Linux.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Problem: board_spl_was_booted_from return wrong boot_devices[3] value
/spi@ff1d0000 and same-as-spl dont work properly for SPINOR flash
because arch/arm/mach-rockchip/spl-boot-order.c spl_node_to_boot_device
need parse SPINOR flash node as UCLASS_SPI_FLASH
spl-boot-order: same-as-spl > *** BOOT_SOURCE_ID 3 (2:emmc 3:spi 5:sd ...
/spi@ff1d0000 > board_boot_order: could not map node @618 to a boot-device
/sdhci@fe330000 > /mmc@fe320000
Solution: just change it to /spi@ff1d0000/flash@0
spl-boot-order: same-as-spl > *** BOOT_SOURCE_ID 3 (2:emmc 3:spi 5:sd ...
/spi@ff1d0000/flash@0 > /sdhci@fe330000 > /mmc@fe320000
Signed-off-by: Artem Lapkin <art@khadas.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Basically all, i.e. rk3036.dtsi, rk3128.dtsi, rk3xxx.dtsi, rk322x.dtsi,
rk3288.dtsi, rk3308-u-boot.dtsi, rk3328-u-boot.dtsi, rk3399-u-boot.dtsi
and px30-u-boot.dtsi Rockchip SoC devicetrees which have mmc indexes
are defining eMMC as mmc0 and sdmmc as mmc1.
This means that the rule to try to boot from the SD card first is ignored,
which as per comment is what we want and is important for distros, which
rely on that.
Fix this by setting the correct mmc index, i.e. first from mmc1 (SD card),
second from mmc0 (eMMC).
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable support to the 2 NOR flashes on the QEMU RISC-V virt machine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Those embers wrapped with CONFIG_SYS_FLASH_CFI in struct flash_info_t
are unconditionally used in the cfi_flash.c driver.
Drop the #ifdefs in the definition of flash_info_t.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The DM version CFI flash driver is in driver/mtd/cfi_flash.c, which
only gets built when FLASH_CFI_DRIVER is on. If CFI_FLASH is on but
FLASH_CFI_DRIVER is not, nothing is enabled at all.
Fix this dependency by selecting FLASH_CFI_DRIVER when CFI_FLASH is
enabled.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Change maintainer to me. Suriyan no longer has this board and wishes
to see someone maintaining it actively.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Change maintainer to me. Eric no longer has this board and wishes
to see someone maintaining it actively.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
If ddr3_init() fails then DDR was not initialized and we cannot load and
execute U-Boot. We cannot continue, we cannot do anything in this case, so
hang.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Returning fabricated CRS value (0xFFFF0001) by PCIe Root Complex to OS is
allowed only for 4-byte PCI_VENDOR_ID config read request and only when
CRSSVE bit in Root Port PCIe device is enabled. In all other error PCIe
Root Complex must return all-ones.
So implement this logic in pci-aardvark.c driver properly.
aardvark HW does not have Root Port PCIe device and U-Boot does not
implement emulation of this device. So expect that CRSSVE bit is set as
U-Boot can already handle CRS value for PCI_VENDOR_ID config read request.
More callers of pci_bus_read_config() function in U-Boot do not check for
return value, but check readback value. Therefore always fill readback
value in pcie_advk_read_config() function. On error fill all-ones of
correct size as it is required for PCIe Root Complex.
And also correctly propagates error from failed config write request to
return value of pcie_advk_write_config() function. Most U-Boot callers
ignores this return value, but it is a good idea to return correct value
from function.
These issues about return value of failed config read requests, including
special handling of CRS were reported by Lorenzo and Bjorn for Linux kernel
driver pci-aardvark together with quotes from PCIe r4.0 spec, see details:
https://lore.kernel.org/linux-pci/20210624213345.3617-1-pali@kernel.org/t/#u
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
During cold start, with some HDDs, mv_sata_identify() does not populate
the ID words on the 1st ATA ID command. In fact, the first ATA ID
command will only power up the drive, and then the ATA ID command
processing is lost in the process.
Tests with:
- Seagate ST9250320AS 250GB HDD and Seagate ST4000DM004-2CV104 4TB HDD.
- Zyxel NSA310S (Kirkwood 88F6702), Marvell Dreamplug (Kirkwood 88F6281),
Seagate GoFlex Home (Kirkwood 88F6281), Pogoplug V4 (Kirkwood 88F6192).
Observation:
- The Seagate ST9250320AS 250GB took about 3 seconds to spin up.
- The Seagate ST4000DM004-2CV104 4TB took about 8 seconds to spin up.
- mv_sata_identify() did not populate the ID words after the call to
mv_ata_exec_ata_cmd_nondma().
- Attempt to insert a long delay of 30 seconds, ie. mdelay(30_000), after
the call to ata_wait_register() inside mv_ata_exec_ata_cmd_nondma() did
not help with the 4TB drive. The ID words were still empty after that 30s
delay.
Patch Description:
- Added a second ATA ID command in mv_sata_identify(), which will be
executed if the 1st ATA ID command did not return with valid ID words.
- Use the HDD drive capacity in the ID words as a successful indicator of
ATA ID command.
- In the scenario where a box is rebooted, the 1st ATA ID command is always
successful, so there is no extra time wasted.
- In the scenario where a box is cold started, the 1st ATA command is the
power up command. The 2nd ATA ID command alleviates the uncertainty of
how long we have to wait for the ID words to be populated by the SATA
controller.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Config option CONFIG_SYS_TCLK is set by kw88f6281.h and kw88f6192.h files
to correct SOC/platform value. So do not overwrite it in board config
include files.
Kirkwood 88F6180 and 88F6192 uses 166 MHz TCLK and Kirkwood 88F6281 uses
200 MHz TCLK.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This mvebu axp platform always uses fixed 250 MHz TCLK. So specify this
CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of
manual configuration in every board file.
Now every #if-#else case of soc.h file defines CONFIG_SYS_TCLK, so remove
useless default CONFIG_SYS_TCLK value from the end of soc.h file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This mvebu msys platform always uses fixed 200 MHz TCLK. So specify this
CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of
manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Bit 20 in SAR register specifies if TCLK is running at 200 MHz or 166 MHz.
Use this information instead of manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Bit 15 in SAR register specifies if TCLK is running at 200 MHz or 250 MHz.
Use this information instead of manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
In DM Ethernet, the old "egiga0" name is no longer valid,
so replace these with Ethernet PHY names from device tree. Also, read
Ethernet PHY address from device tree.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add DM_ETH, SATA_MV and associated configs to goflexhome_defconfig.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Activate the following Kconfig options:
* AVB for Android Verified Boot support
* ADTIMG for merging DTBOs
* ABOOTIMG for extracting Android boot image
Also rework the partitioning tables:
- add a misc partition to handle BCB messages
- add a dtbo partition to store various DTBOs
- add a vbmeta partition for AVB hashes
- Merge vendor and system into the "super" partition
Note: avb support is disables by default. To activate it:
=> setenv force_avb 1;
=> saveenv;
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
doc/README.gpt states:
> The fields 'uuid' and 'uuid_disk' are optional if CONFIG_RANDOM_UUID is
> enabled. A random uuid will be used if omitted or they point to an empty/
> non-existent environment variable. The environment variable will be
> set to the generated UUID. The 'gpt guid' command reads the current
> value of the uuid_disk from the GPT.
Since we have CONFIG_RANDOM_UUID=y, remove the hard-coded uuids
and use meaningful variable names instead.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
There is a mix of spaces and tabs at the leading \. This makes updating
theses lines harder.
Add a single space before each \ for some consistency.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Since Android 10, we are required to use a "dtbo" partition which
includes the various device-tree overlays [1].
It's also possible to provide a "dtb" partition.
This is supported via the "abootimg" command.
On Yukawa, the assumption is that we have only a "dtbo" partition, which
includes all board dtbs and their dtbos [2]
[1] https://source.android.com/devices/architecture/dto/partitions
[2] https://android.googlesource.com/device/amlogic/yukawa/+/refs/heads/master/build/tasks/dtimages.mk#16
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
BOOT_CMD might be different based on CONFIG_CMD_ABOOTIMG.
To prepare for abootimg support, extract the boot command
to a dedicated macro.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Implement A/B slot selection using the U-Boot ab_select command.
Keep support for non A/B.
Not: We need to redefine the recovery partition label, as RecoveryOS
is included in the boot image for A/B systems [1]
[1] https://source.android.com/devices/tech/ota/ab/ab_implement#recovery
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
AVB (Android Verified Boot) is well supported in U-Boot already.
Add support for it in meson64_android.
This is controlled by the "force_avb" environment variable and the
CONFIG_CMD_AVB option.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
To prepare for AVB support, increase SYS_MALLOC_LEN to 128M.
This value has been found by testing the following on khadas vim3l:
=> avb init
=> avb verify
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Permit redefining SYS_MALLOC_LEN for board specific configs.
This is especially useful for Android with AVB, which requires a malloc
length of 128M.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The N2+ dtb is meson-g12b-odroid-n2-plus.dtb, not n2_plus, so
correct the suffix provided in the board file. Also align the
board ident string shown during boot to match.
Fixes: 8bc780106c ("board: amlogic: odroid: add runtime detection of the N2/N2+/C4/HC4 variants")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Various minor bug fixes
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmEQkwoRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZoZwgAxyaO+In1SDc7OlB8/ab/exhgSKxf2oHg
5FYmazygTde1oJNMyv6Xwzzj8AXLAiK5D9Drfom2jsI/gdRWSrMNIVkwR8oFhkO4
+30DEVNrVVrTEDnT1XQJh398fIa2h0uDF2n8KNyhaeacGtLAvNP+LSUdLSoPVHzO
Qc5uD9dDqRpPaVyU5DbzmZ+JS2YhvoWnd8g6zaJXKDexlHCxKr4dGNWlesVEym0q
z9OR6EEO2dZy3HIcLBFfsNLgKWJUoIzQztKuA2l1uEkpmEzOh3bSiLHMv3fOFHG4
aWPq4BTqVeCk4rkd9//krUi4UnN9gL0smKxdFYiWRQecy6jMG2WXjQ==
=IDJp
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-8aug21' of https://source.denx.de/u-boot/custodians/u-boot-dm
Use log subsystem for dm_warn()
Various minor bug fixes
Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART
Log as below: I would keep some debug info for now, and after we move
to be stable and production launch, we could drop that.
U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
Normal Boot
upower_init: soc_id=48
upower_init: version:11.11.6
upower_init: start uPower RAM service
user_upwr_rdy_callb: soc=b
user_upwr_rdy_callb: RAM version:12.6
Turn on switches ok
Turn on memories ok
Clear DDR retention ok
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F0 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
complete
De-Skew PLL is locked and ready
WDT: Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x3a800 by ROM_API
NOTICE: BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94
NOTICE: BL31: Built : 01:56:58, Jun 29 2021
NOTICE: upower_init: start uPower RAM service
NOTICE: user_upwr_rdy_callb: soc=b
NOTICE: user_upwr_rdy_callb: RAM version:12.6
U-Boot 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
CPU: Freescale i.MX8ULP rev1.0 at 744 MHz
Reset cause: POR
Boot mode: Single boot
Model: FSL i.MX8ULP EVK
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... ***
Warning - bad CRC, using default environment
In: serial@293a0000
Out: serial@293a0000
Err: serial@293a0000
Net:
Warning: ethernet@29950000 (eth0) using random MAC address -
96:35:88:62:e0:44
eth0: ethernet@29950000
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add iMX8ULP DDR initialization driver which loads the DDR timing
parameters and executes the training procedure.
When enabling IMX8ULP_DRAM_PHY_PLL_BYPASS, using PHY PLL bypass mode
to do DDR init
Signed-off-by: Ye Li <ye.li@nxp.com>
When booting from boot part1/2, the image offset should be 0, but
ROM has a bug to return 0x8000. Has to workaround the issue before
ROM fix it.
Use a ROM function to know boot from emmc boot part or user part
So we can set the image offset accordingly.
Signed-off-by: Ye Li <ye.li@nxp.com>
Since CMC1 MR0 only reflects high 16 bits boot cfg used for AP domian,
it does not connect to low 16 bits for RTD. So we can't get the correct
boot mode.
Change to use DGO_GP5 of SEC_SIM which is set by ROM.
Signed-off-by: Ye Li <ye.li@nxp.com>
