2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-12-13 23:02:59 +00:00
Commit graph

1975 commits

Author SHA1 Message Date
Jon Nettleton
199b27bb70 mvebu: neta: align DMA buffers
This makes sure the DMA buffers are properly aligned for the
hardware.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:17 -05:00
Kunihiko Hayashi
a8927795ef net: add Socionext AVE ethernet driver support
Add driver for Socionext AVE ethernet controller that includes MAC and
MDIO bus supporting RGMII/RMII modes.
The driver behaves the ethernet driver model (DM_ETH) with devicetree.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:17 -05:00
Radu Bulie
98017a1fb5 drivers/net/vsc9953: Initialize action RAM in VCAP complex
VCAP tables must be initialized even if no advanced classification
is used. If no initialization is performed, then ECC error will
be observed by the user when the first packet enters the l2switch.
The error is marked in MPIC_EISR0 -bit 29 which means - Internal RAM
multi-bit ECC error.
This patch fixes the aforementioned ECC error by performing the
initialization of VCAP tables.

Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:16 -05:00
Alex Kiernan
286bea2e85 net: cpsw: ti: Reap completed packets before stopping interface
If you send a final packet just before stopping the interface (e.g. a final
ACK as part of the UDP fastboot protocol), then that packet isn't reliably
delivered onto the wire.

Reap packets prior to stopping the interface to ensure any which are
in-flight make it out. Also remove buffer and len from the call to
cpdma_process() as we weren't using them on their return.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:16 -05:00
Vicentiu Galanopulo
552e7c57d0 net/phy/cortina: Add support for CS4223 PHY
Add support for Cortina CS4223 10G PHY
  - As per the CS4223 specs, an EEPROM module is
    connected to the PHY. At startup the PHY reads
    the firmware line and tries to load the firmware
    into the internal memory.
  - This driver reads the EEPROM status
    and checks if firmware has been loaded

Signed-off-by: Vicentiu Galanopulo <vicentiu.galanopulo@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:15 -05:00
Joe Hershberger
6e35686d89 net: sunxi: Correct MAC address register order
Put the enetaddr data in the same order as it was before the change in
commit ace1520cb5 ("net: sunxi-emac: Write HW address via function")

Reported-by: Udo Maslo <u.maslo@web.de>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:15 -05:00
Mario Six
5e9d9abe08 tsec: Fix reading phy registers from DT
Bus translations should be applied when reading the address of the sgmii
phy registers from the DT. Use ofnode_get_addr_index instead of the
plain ofnode_read_u32_default to fix this.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:15 -05:00
Vinitha V Pillai
2d91b53331 LS1012AFRWY: Add Secure Boot support
Added the following:
1. defconfig for LS1012AFRWY Secure boot
2. PfE Validation support

Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-11 12:34:45 -07:00
Tom Rini
040b2583c3 Merge branch 'master' of git://git.denx.de/u-boot-sh 2018-06-02 16:58:27 -04:00
Marek Vasut
34f1dba983 net: ravb: Add R8A77990 E3 compatible
Add new compatible to the Ethernet AVB driver for R8A77990 E3 SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-06-01 09:47:02 +02:00
Rick Chen
28b52a6fb7 net: ftmac100: Fix compiler warning
Fix warnings as below when compile in 64-bit.

warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]

Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
2018-05-29 14:45:03 +08:00
Tuomas Tynkkynen
ed9072c797 net: Drop CONFIG_TSI108_ETH
Last user of this driver went away in June 2015 in commit
d928664f41 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support")

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-05-23 17:30:03 -04:00
Chris Packham
f6e62ee04c net: MVGBE don't automatically select PHYLIB
When Kconfig support was added for MVGBE it included automatically
selected PHYLIB support. But MVGBE does not need PHYLIB it will build
fine without it. Commit ed52ea507f ("net: add Kconfig for MVGBE")
should have been a no-op in terms of build size but because of the
selecting PHYLIB the openrd configs increased in size.

Remove the automatic selection of PHYLIB, boards that need it will have
already enabled it in their config header file.

Fixes: commit ed52ea507f ("net: add Kconfig for MVGBE")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-17 17:38:31 +02:00
Chris Packham
ed52ea507f net: add Kconfig for MVGBE
Add Kconfig for MVGBE and update boards to select this.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2018-05-14 21:28:38 -04:00
Chris Packham
edcf7eacbd net: mvgbe: remove CONFIG_DOVE
Nothing defines CONFIG_DOVE so remove the code that uses it.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-05-14 21:28:38 -04:00
Marek Behún
cf2cf8510a net: mvneta: Fix fault when wrong device tree
The driver does not check id phy_connect failed (for example on wrong
property name in device tree). In such a case a fault occurs and the
CPU is restarted.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
Tom Rini
c590e62d3b Merge git://git.denx.de/u-boot-fsl-qoriq 2018-05-11 07:09:21 -04:00
Tom Rini
f739fcd831 SPDX: Convert a few files that were missed before
As part of the main conversion a few files were missed.  These files had
additional whitespace after the '*' and before the SPDX tag and my
previous regex was too strict.  This time I did a grep for all SPDX tags
and then filtered out anything that matched the correct styles.

Fixes: 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-10 20:38:35 -04:00
Yogesh Gaur
a6f2a6eafe driver: net: fsl-mc: updated copyright info
Updated copyright info for the issues reported after running
check-legal test.

Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-09 09:17:51 -05:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Tom Rini
b25f8e2112 Merge git://git.denx.de/u-boot-imx 2018-04-30 07:14:05 -04:00
Tom Rini
d024236e5a Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTR
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:48 -04:00
Adam Ford
f1b1f77060 Convert CONFIG_SPI to Kconfig
This converts the following to Kconfig:
   CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver.  For now, just update
the CONFIG tests.  This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:11 -04:00
Lukasz Majewski
948239ea16 dts: dm: fec: imx53: Provide proper compatible string for imx53 fec driver
After this change the DM FEC ETH driver can be also reused on some imx53
devices.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-04-26 09:28:49 +02:00
Lukasz Majewski
178d4f0099 eth: dm: fec: Change FEC PHY mask setting from CONFIG_PHYLIB to CONFIG_FEC_MXC_PHYADDR
Without this commit we do have an explicit dependency on CONFIG_PHYLIB
when one wants to set PHY ADDR on a iMX board (FEC + driver model).

This shall be changed to CONFIG_FEC_MXC_PHYADDR, as only when we do have
it set, we shall mask out other devices.

As a side effect, when CONFIG_FEC_MXC_PHYADDR is not set, we scan PHY bus
for connected PHY devices.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-04-26 09:27:22 +02:00
Joe Hershberger
16879cd25a net: phy: Don't limit phy addresses by default
Some boards expect to find more than one phy while other boards are old
and need to be limited to a specific phy address. Only limit the phy
address for boards that opt in.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-04-13 15:56:47 -05:00
Marek Vasut
b107fd5bab net: sh_eth: Add remaining Gen2 DT compatible
Add compatible strings for R8A7790, R8A7793 and R8A7794, since the
contemporary DTs use those don't have a generic match value.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:52 -05:00
Siva Durga Prasad Paladugu
69065e8ff4 net: zynq_gem: Use max-speed property from dt
Add support to use max-speed property from dt for
determining the supported speed. Use 1000Mbps as
default.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:48 -05:00
Ye Li
2087eac257 net: fec: Fix issue in DM probe timeout
Since the probe function has changed to reset FEC controller prior than
setup PHY. If reset FEC controller timeout, the priv->phydev is not
initialized, so can't free it.

Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:39 -05:00
Peng Fan
979e0fc862 net: fex_mxc: add i.MX6UL/SX/SL compatible
Add i.MX6UL/SX/SL compatible.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:39 -05:00
Peng Fan
fbada4855d net: fec: sharing MDIO for two enet controllers
On i.MX6SX, 6UL and 7D, there are two enet controllers each has a
MDIO port. But Some boards share one MDIO port for the two enets. So
introduce a configuration CONFIG_FEC_MXC_MDIO_BASE to indicate
the MDIO port for sharing.
In Kconfig, user needs enable CONFIG_FEC_MXC_SHARE_MDIO first to enter
the CONFIG_FEC_MXC_MDIO_BASE.

To i.MX28, adapt to use the new config

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-13 15:47:38 -05:00
Peng Fan
8b20386356 net: fec: set dev->seq to priv->dev_id
To platforms has two enet interface, using dev->seq could
avoid conflict.

i.MX6UL/ULL evk board net get the wrong MAC address from fuse,
eth1 get MAC0 address, eth0 get MAC1 address from fuse. Set the
priv->dev_id to device->seq as the real net interface alias id then
.fec_get_hwaddr() read the related MAC address from fuse.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:38 -05:00
Peng Fan
1bcabd7921 net: fec_mxc: simplify fec_get_miibus
No need to provide two prototype for this function.
Use ulong for the first parameter, then this function
could be shared for DM/non DM case.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:37 -05:00
Ye Li
07763ac928 net: fec_mxc: Fix DM driver issue in recv
When using ethernet DM driver, the recv interface has a
change with non-DM interface, that driver needs to set
the packet pointer and provide it to upper layer to process.

In fec driver, the fecmxc_recv functions does not handle the
packet pointer parameter. This may cause crash in upper layer
processing because the packet pointer is not set.

This patch allocates a buffer for the packet pointer and free it
through free_pkt interface.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:37 -05:00
Matt Pelland
0a85f024c5 net: mvneta: support setting hardware address
mvneta already supports setting the MAC address but this was only done
internally when some other part of U-Boot tries to actually use the
interface. This commit exposes this functionality to the ethernet core
code so that the MAC addresses of all interfaces are configured
correctly even if they are not used before loading Linux.

Signed-off-by: Matt Pelland <mpelland@starry.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13 15:47:31 -05:00
Tom Rini
2600df4f8e Xilinx changes for v2018.05-rc2
- Various DT changes and sync with mainline kernel
 - Various defconfig updates
 - Add SPL init for zcu102 revA
 - Add new zynqmp boards zcu100/zcu104/zcu106/zcu111/zc12XX
   and zc1751-dc3
 - Net fixes - xlnx,phy-type
 - 64bit axi ethernet support
 - arasan: Fix nand write issue
 - fpga fixes
 - Maintainer file updates
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iEYEABECAAYFAlrLeoUACgkQykllyylKDCEilwCgmdalBG7zVd9oekK142ILPdRf
 OgsAn2oWw69JhU3i4mv039lNgYpIzlRb
 =shae
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2018.05-rc2' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.05-rc2

- Various DT changes and sync with mainline kernel
- Various defconfig updates
- Add SPL init for zcu102 revA
- Add new zynqmp boards zcu100/zcu104/zcu106/zcu111/zc12XX
  and zc1751-dc3
- Net fixes - xlnx,phy-type
- 64bit axi ethernet support
- arasan: Fix nand write issue
- fpga fixes
- Maintainer file updates
2018-04-09 11:06:21 -04:00
Siva Durga Prasad Paladugu
c643c491b9 net: phy: xilinx_phy: Read phytype using property xlnx,phy-type
This patch reads phytype from property "xlnx,phy-type" instead
od simply looking for "phy-type". This is to be inline with
Linux and also fixes the issue of detecting it wrongly in
u-boot.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-09 12:14:51 +02:00
Vipul Kumar
047f3bf828 axi: ethernet: Added support for 64 bit addressing for axi-ethernet
This patch uses writeq() function to enable greater than 32 bit
addressing of axi-ethernet for the ZynqMP devices.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-09 12:14:50 +02:00
Alex Kiernan
9925f1dbc3 net: Move enetaddr env access code to env config instead of net config
In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.

This fixes failures such as:

  board/ti/am335x/built-in.o: In function `board_late_init':
  board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
  u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'

which caters for use cases such as:

commit f411b5cca4 ("board: am335x: Always set eth/eth1addr environment
variable")

when Ethernet is required in Linux, but not U-Boot.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-04-08 23:00:58 -04:00
Alex Kiernan
f02b8d1761 Migrate CONFIG_DRIVER_TI_CPSW to Kconfig
This converts CONFIG_DRIVER_TI_CPSW to Kconfig

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-08 23:00:58 -04:00
Mario Six
171510522e treewide: Migrate CONFIG_TSEC_ENET to Kconfig
Migrate the CONFIG_TSEC_ENET option to Kconfig.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08 15:12:53 -04:00
Christophe Leroy
18f8d4c60d powercp: mpc8xx: move commproc.h
include/commproc.h is dedicated to the 8xx, rename it cpm_8xx.h and
move it into arch/powerpc/include/asm

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2018-04-06 16:30:37 -04:00
Christophe Leroy
ee1e600c13 powerpc: mpc8xx: Change CONFIG_8xx to CONFIG_MPC8xx
CONFIG_8xx doesn't mean much outside of arch/powerpc/
This patch renames it CONFIG_MPC8xx just like CONFIG_MPC85xx etc ...
It also renames 8xx_immap.h to immap_8xx.h to be consistent with
other file names.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2018-04-06 16:30:37 -04:00
Tom Rini
e294ba0678 Merge git://git.denx.de/u-boot-sunxi
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-04 14:10:39 -04:00
Andre Przywara
ecd0cec04c net: sun8i-emac: remove support for old binding
The original DT binding used by U-Boot's sun8i-emac driver was not really
agreed upon, and deviated from the "official" binding now used by the
kernel. Since now all U-Boot users have been converted to the new
binding, we can remove support for the old DT nodes from the driver.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-04-04 11:31:35 +05:30
Andre Przywara
12afd95711 net: sun8i-emac: add support for new EMAC DT binding
The Ethernet MAC used in newer Allwinner SoCs (H3, A64, H5) got an
upstream Linux driver in v4.15.
This one uses a slightly different binding from the original one used
by the U-Boot driver.
The differences to the old binding are:
- The "syscon" address is held in a separate node, referenced via a
  phandle in the "syscon" property.
- The reference to the PHY is held in a property called "phy-handle",
  not "phy".
- The PHY register is at offset 0x30 in the syscon device, not at 0.
- The internal PHY is activated when the node, which phy-handle points
  to, is a child node of an "allwinner,sun8i-h3-mdio-internal" node.

Teach the U-Boot driver how to find its resources in a "new-style" DT,
so that we can use a Linux kernel compatible DT for U-Boot as well.
This keeps support for the old binding for now, to allow a smooth
transition.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-04-04 11:31:35 +05:30
Andre Przywara
c034117302 net: sun8i-emac: support new pinctrl DT bindings
The Linux kernel driver for the Allwinner pin controller gained support
for generic properties, which are now also used in the DTs.
The sun8i-emac Ethernet driver for new Allwinner MACs reads the pins from
the DT, but so far only supported the old binding.
Update the parsing routine to cope with both the old and new bindings,
so that the newer DTs can be used with U-Boot and its Ethernet driver.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-04-04 11:31:35 +05:30
Siva Durga Prasad Paladugu
d77081cf50 net: zynq_gem: Dont run any phy detection logic for GMII case
This patch bypasses phy detection logic for GMII interface
and just depend on phy address received from DT. This patch
is required as phy detection logic is different for some phys
like xilinx phy which can be connected over SGMII and GMII
interface.
This fixes the issue of ethernet failures when xilinx phy is
connected over GMII interface.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-23 09:34:42 +01:00
Tuomas Tynkkynen
d04791dfa5 net: Drop CONFIG_ENC28J60
Last user of this driver went away in October 2014 in
commit d58a9451e7 ("ppc/arm: zap EMK boards").

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:32 -05:00
Heinrich Schuchardt
6cdf072d9e net: macb: remove superfluous logical constraint
In

	if (a > =0) {...}
	else (a < 0) {...}

the second logical constraint is superfluous.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:32 -05:00
Heinrich Schuchardt
4b23d3c864 drivers: net: cpsw: remove superfluous assignment.
In

	int ret = A;
	ret = B;

the first assignment has not effect.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:32 -05:00
Priyanka Jain
b321c44ac9 net/phy/cortina: Add No firmware upload option
Current Cortina phy driver assumes that firmware upload
is required during initialization and is dependent
on presence of corresponding macros like CONFIG_CORTINA_FW_ADDR
for compilation.

But Cortina phy has provision to store phy firmware in
attached dedicated EEPROM. And boards designed with such
EEPROM does not require firmware upload.

Add CORTINA_NO_FW_UPLOAD option in cortina.c to support
such boards.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:31 -05:00
Priyanka Jain
af5484acb0 net/phy/cortina.c: Update get_phy_id implementation
Update get_phy_id() implementation in cortina.c to check
for Cortina_phy by comparing device phy_id with cortina phy_id
instead of relying on presence of CORTINA macros.

This will allow get_phy_id to work with non-cortina phy devices
which might have same phy address as Cortina device but on
different  bus.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:31 -05:00
Calvin Johnson
a802d1e268 configs: ls1012a: add pfe configuration for LS1012A
Add configurations for PFE.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:31 -05:00
Calvin Johnson
6281a769b3 drivers: net: pfe_eth: provide pfe commands
pfe_command provides command line support for several features that
support pfe, like starting or stopping the pfe, checking the health
of the processor engines and checking status of different units inside
pfe.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:28 -05:00
Calvin Johnson
a4a4043749 drivers: net: pfe_eth: LS1012A PFE driver introduction
This patch adds PFE driver to U-Boot

Following are the main driver files:-
pfe_hw.c: provides low level helper functions to initialize PFE
internal processor engines and other hardware blocks
pfe_driver.c: provides initialization functions
and packet send and receive functions
pfe_eth.c: provides high level gemac initialization functions
pfe_firmware.c: provides functions to load firmware into PFE
internal processor engines.
pfe_mdio.c: provides functions to initialize phy and mdio.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:28 -05:00
Calvin Johnson
365108ef52 drivers: net: phy: Fix aquantia compilation with DM
With CONFIG_DM_ETH enabled, aquantia driver compilation fails with
below error. This patch fixes the issue by including dm.h.

drivers/net/phy/aquantia.c: In function ‘aquantia_startup’:
drivers/net/phy/aquantia.c:73:21: error: dereferencing pointer to
incomplete
type ‘struct udevice’
          phydev->dev->name);
		     ^~

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:28 -05:00
Heinrich Schuchardt
b24b1e4b1d net: mvpp2x: add check after calloc
After allocating plat the pointer is checked.
Afterwards name is allocated and not checked.

Add the missing check to avoid a possible NULL dereference.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:28 -05:00
kevans@FreeBSD.org
66526e7038 net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys
Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off
on the PHY, as well as flipping some magical undocumented bits. The
magic number comes from the Pine64 engineering team, presumably as a
proxy from Realtek. This configuration fixes the throughput on some
Pine64 models. Packet loss of up to 60-70% has been observed without
this.

Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:27 -05:00
Stefan Mavrodiev
b30c419040 Move CONFIG_PHY_ADDR to Kconfig
CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).

Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.

After the implemention, moveconfig was run. The issues are:
	- edb9315a	- CONFIG_PHYLIB is not enabled. Entry is
			  deleted.

	- ds414		- CONFIG_PHYLIB is in incompatible format:
			  { 0x1, 0x0 }. This entry is also deleted.

	- devkit3250	- The PHY_ADDR is in hex format (0x1F).
			  Manually CONFIG_PHY_ADDR=31 is added in
			  the defconfig.

After the changes the suspicious defconfigs passes building.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-13 22:36:33 +05:30
Samuel Holland
2d53018a0e net: sun8i_emac: Fix PHY initialization
The previous code tried to update the PHY parameters without waiting for
autonegotiation to complete. This caused wrong values to be written to
the EMAC in sun8i_adjust_link(). As a result, any commands that called
eth_start() before autonegotiation completed would find the network
nonfunctional. Fix this by using the correct function to start up the
PHY.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-13 21:16:51 +05:30
Tom Rini
81f077f40f Merge git://git.denx.de/u-boot-sh 2018-03-05 20:24:17 -05:00
Masahiro Yamada
b08c8c4870 libfdt: move headers to <linux/libfdt.h> and <linux/libfdt_env.h>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.

This commit moves the header code:
  include/libfdt.h         -> include/linux/libfdt.h
  include/libfdt_env.h     -> include/linux/libfdt_env.h

and replaces include directives:
  #include <libfdt.h>      -> #include <linux/libfdt.h>
  #include <libfdt_env.h>  -> #include <linux/libfdt_env.h>

Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-05 10:16:28 -05:00
Marek Vasut
7a7081e6f3 net: ravb: Add R8A77965 M3N entries
Add entries for the R8A77965 M3N SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-03-05 10:59:37 +01:00
Arno Steffens
a0fd381fc6 net: phy: smsc: Add SMSC LAN8741 support
Signed-off-by: Arno Steffens <star@gmx.li>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-26 15:51:37 -06:00
Bernhard Messerklinger
8f5672ea9d net: e1000: Fix e1000_igb semaphore handling
Fix commit f1bcad22dd ("net: e1000: add support for writing to
EEPROM").

Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-26 15:51:36 -06:00
Eugeniy Paltsev
1693a577be NET: designware: fix clock enable
After commit ba1f966725 ("net: designware: add clock support")
we got NET broken on axs101 and axs103 platforms.

Some clock don't support gating so their clock drivers don't
implement .enable/.disable callbacks. In such case clk_enable
returns -ENOSYS.
Also some clock drivers implement .enable/.disable callbacks not for all
clock IDs and return -ENOSYS (or -ENOTSUPP) for others.

If we have such clock in 'clocks' list of designware ethernet controller
node we fail to probe designware ethernet.

Fix it.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-02-26 15:49:26 -06:00
Mario Six
8d6312032e phy: Fix style violations
Fix some style violations in the generic PHY management code.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-02-26 15:48:55 -06:00
Mario Six
431be621c6 net: phy: marvell 88e151x: Fix handling of bare RGMII interface type
Commit 68e6ecadc5 ("net: phy: marvell 88e151x: Fix handling of RGMII
interface types") fixed the initialization of 88e151x phys, but made it
so that interfaces of type PHY_INTERFACE_MODE_RGMII had both RX and TX
delay bits cleared. The default (like in m88e1111s_config) is to have
both bits set.

Hence, this patch changes the behavior in the PHY_INTERFACE_MODE_RGMII
case so that both bits are set.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-26 15:47:07 -06:00
Mario Six
76f11d3adf net: phy: marvell: Fix style violations
Fix some style violations (mostly wrong indentions) in the Marvell PHY
driver.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-02-26 15:46:09 -06:00
Mario Six
1313aaf031 net: tsec: Make live-tree compatible
Make the tsec ethernet driver compatible with a live device tree.

Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-02-26 15:45:56 -06:00
Mario Six
5775f00e12 net: tsec: Fix memory leak in error path
tsec_initialize allocates a private driver structure using malloc.
Should the memory allocation of this private structure fail, the
function execution is aborted with a return 0, but the previously
allocated device structure is never freed, hence leaked.

Free the device structure in the error case.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-26 15:28:43 -06:00
Mario Six
d38de3380d net: tsec: Fix style violations
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-26 15:28:39 -06:00
Michal Simek
744247de29 net: Remove Xilinx ll_temac driver
ll_temac driver was used by Xilinx Microblaze big endian and
Xilinx ppc405/ppc440 SoCs.

ppc support was removed by: "powerpc: remove 4xx support"
(sha1: 98f705c9ce)
and Microblaze BE is not tested for a long time that's why this driver
can be removed because none is going to updated it to DM anyway.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-23 10:40:51 -05:00
Marek Vasut
5abcbd7847 net: sh_eth: Fix DT base address fetching
Drop the whole map/unmap_physmem stuff and just use the address
already obtained from DT in ofdata_to_platdata(), instead of
repeating that, wrongly, in probe.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-02-18 11:20:18 +01:00
Marek Vasut
5262767ded net: sh_eth: Fix checkpatch warning
Fix minor checkpatch warning about udelay(3000) being too long
and should be replaced by mdelay(3).

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-02-18 11:20:18 +01:00
Marek Vasut
60279b5757 net: sh_eth: Return directly from sh_eth_recv_start
Drop the len variable, it's useless.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-02-18 11:20:18 +01:00
Marek Vasut
3c5a7b7547 net: sh_eth: Zap port variable
Inline this variable which is quite useless.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-02-18 11:20:17 +01:00
Marek Vasut
d64c789414 net: ravb: Initialize PHY in probe() once
Reset and initialize the PHY once in the probe() function rather than
doing it over and over again is start() function. This requires us to
keep the clock enabled while the driver is in use. This significantly
reduces the time between transfers as the PHY doesn't have to restart
autonegotiation between transfers, which takes forever.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-02-16 16:43:09 +01:00
Michal Simek
c946b0e9fd Kconfig: net: phylib: Phylib should depends on NET
There is no value to enable phylib without networking support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-08 12:48:10 -05:00
Hannu Lounento
8d9bde0dbb net: e1000: implement eth_write_hwaddr
Implement programming MAC address to the hardware, i.e. external flash
seen as EEPROM.

MAC address is only written if it differs from what is already stored in
flash or if reading the current MAC address fails.

Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-02-04 12:00:58 +01:00
Hannu Lounento
e0a75fed9e net: e1000: split e1000_read_mac_addr
Split the implementation of e1000_read_mac_addr into eeprom and register
versions called by e1000_read_mac_addr.

This allows for calling e1000_read_mac_addr when MAC address is needed
with no constraints where it is read from, and for calling the register
and, especially, the eeprom version directly in order to specify where
to read the address from.

Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-02-04 12:00:58 +01:00
Hannu Lounento
f1bcad22dd net: e1000: add support for writing to EEPROM
Port functions for writing to EEPROM, updating the checksum and
committing data to flash from the Linux kernel igb driver.

Functions were ported from Linux 4.8-rc2 (694d0d0bb20).

Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-02-04 12:00:58 +01:00
Ye Li
f24e482ae0 net: fec: fix build warnings for 64bits support
When building for 64bits system, we get some warnings about type
cast between pointer and integer. This patch eliminates the warnings
by using ulong/long type which is 32bits on 32bits system or 64bits on
64bits system.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-02-04 12:00:58 +01:00
Peng Fan
238a53c710 net: fec: do not access reserved register for i.MX8M
The MIB RAM and FIFO receive start register does not exist on
i.MX8M. Accessing these register will cause system hang.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2018-02-04 12:00:58 +01:00
Tom Rini
48f58a5973 Merge git://git.denx.de/u-boot-fsl-qoriq 2018-01-31 18:44:31 -05:00
Yogesh Gaur
f9747a5a5d driver: fsl-mc: Perform fsl-mc fdt fixup for lazyapply dpl
For for case of lazyapply method, API fdt_fixup_board_enet() gets
invoked before DPL being deployed. This leads to an issue that
fsl-mc fdt fixup status marked as fail and dprc driver didn't get
registered in linux boot.

Fixes this issue by calling fdt_fixup_board_enet() for case when
DPL is deployed successfully in lazyapply method.

Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-30 09:13:32 -08:00
Tom Rini
c5e6e9b3d6 mvpp2: Fix warning over 32bit vs 64bit targets
When we have a driver that is used on both 32bit and 64bit targets and
we are talking about address space we cannot use u64 nor u32 and instead
need to use phys_addr_t.

Fixes: 377883f16d ("net: mvpp2x: fix phy connected to wrong mdio issue")
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2018-01-29 12:48:34 -05:00
David Wu
d12d7c09eb net: gmac_rockchip: Add support for the RK3228 GMAC
The GMAC in the RK3228 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.

This adds the RK3368-specific logic necessary to reuse this driver.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-28 17:12:38 +01:00
David Wu
b3d2a6df30 net: gmac_rockchip: Add rk3328 gmac support
The GMAC2IO in the RK3328 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.

This adds the RK3328-specific logic necessary to reuse this driver.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-28 17:12:37 +01:00
David Wu
caf746172b net: gmac_rockchip: Add support for the RV1108 GMAC
The rv1108 GMAC only support rmii interface, so need to add the
set_rmii() ops. Use the phy current interface to set rmii or
rgmii ops. At the same time, need to set the mac clock rate of
rmii with 50M, the clock rate of rgmii with 125M.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-28 17:12:37 +01:00
Tom Rini
9c486e7cb0 Merge branch 'rmobile-mx' of git://git.denx.de/u-boot-sh 2018-01-27 18:25:00 -05:00
Marek Vasut
319202640a net: sh_eth: Add DM and DT support
Add DM capable code into the SH ethernet driver and support probing
both from DT and pdata. The legacy non-DM, non-DT support is retained
as there are still systems in the tree which are not DM or DT capable.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-01-27 20:38:53 +01:00
Marek Vasut
a220784b14 net: sh_eth: Clump legacy functions together
Move the legacy functions around, so that they can be wrapped in a
massive ifdef CONFIG_DM_ETH once DM support is added. No functional
change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-01-27 20:38:53 +01:00
Marek Vasut
013af64f8f net: sh_eth: Split sh_eth_init
Split sh_eth_init() function into smaller chunks, which can
be called from both DM and non-DM code while handling the
specifics of both configurations.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-01-27 20:38:53 +01:00
Marek Vasut
68ac92e937 net: sh_eth: Separate out MAC address programming
Pull out the code for writing MAC address into the NIC into a
separate function, so it can be reused by both DM and non-DM
code. This is done in preparation for DM support, which handles
MAC address programming separately.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-01-27 20:38:53 +01:00
Marek Vasut
52c15e220b net: sh_eth: Split sh_eth_recv
Split sh_eth_recv into two functions, one which checks whether
a packet was received and one which handles the received packet.
This is done in preparation for DM support, which handles these
two parts separately.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-01-27 20:38:53 +01:00
Marek Vasut
dca221bd92 net: sh_eth: Pass sh_eth_dev around
Pass sh_eth_dev structure around instead of eth_device, since the
later is specific to the legacy networking support. This change is
done in preparation for the DM addition.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-01-27 20:38:53 +01:00
Marek Vasut
effb79027e net: sh_eth: Unify CONFIG_R8A779[01234] as CONFIG_RCAR_GEN2
Use the common RCAR_GEN2 config option instead of enumerating
each SoC and having a lengthy ifdef clause. No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-01-27 20:38:53 +01:00
Marek Vasut
e3105eacf5 net: ravb: staticize ravb_start
Cosmetic fix, make ravb_start() static.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-01-27 20:38:53 +01:00