Many of the help messages were not really helpful; for example, many
commands that take no arguments would not print a correct synopsis
line, but "No additional help available." which is not exactly wrong,
but not helpful either.
Commit ``Make "usage" messages more helpful.'' changed this
partially. But it also became clear that lots of "Usage" and "Help"
messages (fields "usage" and "help" in struct cmd_tbl_s respective)
were actually redundant.
This patch cleans this up - for example:
Before:
=> help dtt
dtt - Digital Thermometer and Thermostat
Usage:
dtt - Read temperature from digital thermometer and thermostat.
After:
=> help dtt
dtt - Read temperature from Digital Thermometer and Thermostat
Usage:
dtt
Signed-off-by: Wolfgang Denk <wd@denx.de>
The boards that get converted here to use the environment for the mac
address rather than global data:
debris
mgcoge
mgsuvd
muas3001
netstal
pn62
sixnet
vcma9
xilinx (the ones that use xilinx_enet)
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Sangmoon Kim <dogoil@etinsys.com>
CC: Heiko Schocher <hs@denx.de>
CC: David Mueller <d.mueller@elsoft.ch>
CC: Niklaus Giger <niklaus.giger@netstal.com>
CC: Wolfgang Grandegger <wg@denx.de>
CC: Dave Ellis <DGE@sixnetio.com>
CC: Ricardo Ribalda <ricardo.ribalda@uam.es>
This patch adds support for the kmsupx4 board from Keymile,
based on a Freescale MPC852T CPU
- serial console on SMC1
- 32 MB SDRAM
- 32 MB NOR Flash
- Ethernet over SCC3
- I2C Bitbang
Signed-off-by: Heiko Schocher <hs@denx.de>
renaming the "mgsuvd" board port into "km8xx", because
there come more similar boards from keymile.
Compiling the mgsuvd board with "make mgsuvd_config"
remains.
Signed-off-by: Heiko Schocher <hs@denx.de>
old code implemented the QE_ENET10 errata only for Silicon
Revision 2.0. New code reads now the Silicon Revision
register and sets dependend on the Silicon Revision the
values as advised in the QE_ENET10 errata.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
it is possible that some board variants have different DDR II
RAM sizes. So we autodetect the size of the assembled RAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds I2C support for the Keymile kmeter1 board.
It uses the First I2C Controller from the CPU, for
accessing 4 temperature sensors, an eeprom with IVM data
and the booteeprom over a pca9547 mux.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- activate CS4 for accessing the FPGA
- activate Rx buf len > 1 on SMC
- pram activated
- MTDPARTS_DEFAULT defined
- update the size of the flashes in the DTS
before booting Linux
- MONITOR_LEN updated to 384k
- added CONFIG_HOSTNAME
- added CONFIG_ENV_BUFFER_PRINT
- Environment size reduced to 16k
Signed-off-by: Heiko Schocher <hs@denx.de>
- activate Rx buf len > 1 on SMC
- pram activated
- MTDPARTS_DEFAULT defined
- update the size of the flash in the DTS
before booting Linux
- MONITOR_LEN updated to 384k
- added CONFIG_HOSTNAME
- added CONFIG_ENV_BUFFER_PRINT
- Environment size reduced to 16k
Signed-off-by: Heiko Schocher <hs@denx.de>
Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Check the presence of the PIGGY on the keymile boards mgcoge,
mgsuvd and kmeter1. If the PIGGY is not present, dont register
this Ethernet device.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds support for the kmeter1 board from Keymile,
based on a Freescale MPC8360 CPU.
- serial console on UART 1
- 256 MB DDR2 RAM
- 64 MB NOR Flash
- Ethernet RMII Mode over UCC4
- PHY SMSC LAN8700
Signed-off-by: Heiko Schocher <hs@denx.de>
Most of the bss initialization loop increments 4 bytes
at a time. And the loop end is checked for an 'equal'
condition. Make the bss end address aligned by 4, so
that the loop will end as expected.
Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
in ft_blob_update () for both boards was an unneccessary
repetition of code, which this patch moves in a common
function for this boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
The EEprom contains some Manufacturerinformation,
which are read from u-boot at boot time, and saved
in same hush shell variables.
Signed-off-by: Heiko Schocher <hs@denx.de>
As documented in doc/I2C_Edge_Conditions, adding a
board specific deblocking mechanism via CFG_I2C_INIT_BOARD
for the mgcoge and mgsuvd board.
This code was originally written by Keymile in association
with Anatech and Atmel in 1998. The Code toggels the SCL
until the SCA line goes to HIGH (max. 16 times).
And after this, a start condition is sent.
This is another approach to deblock the I2C Bus. The
soft I2C driver actually sends 9 clocks with SDA High,
and then a stop at the end, to deblock the I2C Bus.
Maybe we should use the approach from Keymile as
the new standard?
Signed-off-by: Heiko Schocher <hs@denx.de>
There are some more extensions, which are for both boards
and some more boards from this manufacturer will follow soon.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
