It is possible to boot device using a micro SD or eMMC slots.
In this situation, boot device should be registered as a block
device 0 in the MMC framework, because CONFIG_SYS_MMC_ENV_DEV
is usually set to "0" in the most config cases.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The byte order of soc revision was inverted, now it is fixed.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The help message in board/ti/am335x/Kconfig says AM335x has
6 UARTs, so the valid number for CONFIG_CONS_INDEX is from 1 to 6.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
The QS Systems TQMa6 board support was added by commit cb07d74e
and lost by commit e82abaeb.
Commit e82abaeb merged the IMX branch based on pre-Kconfig
and the mainline based on post-Kconfig, simply deleting
the boards.cfg file. As a result, some boards added just before
the merge were lost.
This commit adds Kconfig, defconfig, MAINTAINERS for TQMa6 board
to work on the Kconfig infrastructure.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Stefano Babic <sbabic@denx.de>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Nomadik board select menu to nomadik/Kconfig.
Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="nomadik").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Orion5x board select menu to orion5x/Kconfig.
Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="orion5x").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Keystone board select menu to keystone/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="keystone").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP5 board select menu to omap5/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap5").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP4 board select menu to omap4/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap4").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP3 board select menu to omap3/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap3
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Davinci board select menu to davinci/Kconfig.
Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="davinci").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Exynos board select menu to exynos/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="exynos").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the KirkWood board select menu to kirkwood/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="kirkwood").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Prafulla Wadasdkar <prafulla@marvell.com>
Cc: Luka Perkov <luka@openwrt.org>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Rmobile board select menu to rmobile/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="rmobile").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Tegra board select menu to tegra/Kconfig.
Insert the Tegra SoC select menu between the arch select and the
board select.
Architecture select
|-- Tegra Platform (Tegra)
|- Tegra SoC select (Tegra20 / 30 / 114 / 124)
|- Board select
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows:
config TEGRA
bool
select SPL
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Zynq board select menu to zynq/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="zynq").
Refactor board/xilinx/zynq/MAINTAINERS too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Commit 41623c9 'arm: move exception handling out of start.S files' missed some
linker scripts. Hence, some boards no longer had exception handling linked since
this commit. Restore the original behavior by adding the .vectors section to
these linker scripts.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
The bcm_ep board configuration is used by a number of boards
including Cygnus and NSP.
Add builds for the bcm958300k and the bcm958622hr boards.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
The email address of Matt Waddel is no longer working.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alexei Fedorov <alexie.fedorov@arm.com>
To enable hypervisors utilizing the ARMv7 virtualization extension
on the Arndale board, add the simple SMP pen address writer function
and add the required configuration variables to switch all cores to
HYP mode before launching the OS.
This allows booting KVM and Xen directly from u-boot.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
However ep9315 don't use
interrupt vectors during startup, but _startup symbol is used inside uboot to
calculate actual monitor size.
Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
Enable initialization fo designware ethernet controller. With this
patch, ethernet works in my configuration, provided I set ethernet
address in the environment.
Signed-off-by: Pavel Machek <pavel@denx.de>
Though nios2-generic board meant to be a template, it is helpful
to be able to test on a real hardware. As the nios2 linux is
developed and tested on a 3c120 FPGA based Golden Hardware Reference
Design, it makes sense to rebase nios2-generic on this FPGA design.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
This patch changes the link script to base at CONFIG_SYS_MONITOR_BASE.
Then we can remove the text_base hook in nios2-generic board.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
To fix the build error when build for Altera dev kit, not
virtual target. At same time, set the build for Altera dev
kit as default instead virtual target. With that, U-Boot
is booting well and SPL still lack of few drivers.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Initialization of pointer from integer shall be designated by explicit
type cast.
Signed-off-by: Vasili Galka <vvv444@gmail.com>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
resync ubi subsystem with linux:
commit 455c6fdbd219161bd09b1165f11699d6d73de11c
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun Mar 30 20:40:15 2014 -0700
Linux 3.14
A nice side effect of this, is we introduce UBI Fastmap support
to U-Boot.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Joerg Krause <jkrause@posteo.de>
DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards,
and left unused on previous boards, so it is safe enough to enable gpio
on all DRA7 boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
- Drop CONFIG_SERIAL[1-6] and use CONFIG_CONS_INDEX tests instead
- Add choice and help text to board/ti/am335x/Kconfig
- Correct comment about IDK in board/ti/am335x/mux.c
- Remove am335x_evm_uart* defconfig files as they're just variations
on a config option now.
Signed-off-by: Tom Rini <trini@ti.com>
Boot from eMMC boot partition corresponds to BOOT_DEVICE_MMC2
omap_bootmode, while BOOT_DEVICE_MMC2_2 corresponds to the user
data partition boot.
Fix mmc_get_env_part() boot mode check to use a correct value.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Fix cl_eeprom_read_mac_addr() return value check.
Fix long line codding style issue in board_init().
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
This patch reads EFUSE_BOOTROM register to see the maximum supported
clock for CORE and TETRIS PLLs and configure them accordingly.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-select[0] and accessed
as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and
is CFI compatible.
As multiple devices are share GPMC pins on this board, so following board
settings are required to detect NOR device:
SW5.1 (NAND_BOOTn) = OFF (logic-1)
SW5.2 (NOR_BOOTn) = ON (logic-0) /* Active-low */
SW5.3 (eMMC_BOOTn) = OFF (logic-1)
SW5.4 (QSPI_BOOTn) = OFF (logic-1)
And also set appropriate SYSBOOT configurations:
SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */
SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */
SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */
SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */
SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */
SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */
Also, following changes are required to enable NOR Flash support in
dra7xx_evm board profile:
This patch adds support for NAND device connected to GPMC chip-select on
following AM43xx EVM boards.
am437x-gp-evm: On this board, NAND Flash signals are muxed with eMMC, thus at a
time either eMMC or NAND can be enabled. Selection between eMMC and NAND is
controlled by:
(a) Statically using Jumper on connecter (J89) present on board.
(a) If Jumper on J89 is NOT used, then selection can be dynamically controlled
by driving SPI2_CS0[MUX_MODE=GPIO] pin via software:
SPI2_CS0 == 0: NAND (default)
SPI2_CS0 == 1: eMMC
am43x-epos-evm: On this board, NAND Flash control lines are muxed with QSPI,
Thus only one of the two can be used at a time. Selection is controlled by:
(a) Dynamically driving following GPIO pin from software
GPMC_A0(GPIO) == 0 NAND is selected (default)
NAND device (MT29F4G08AB) on these boards has:
- data-width=8bits
- blocksize=256KB
- pagesize=4KB
- oobsize=224 bytes
For above NAND device, ROM code expects the boot-loader to be flashed in BCH16
ECC scheme for NAND boot, So by default BCH16 ECC is enabled for AM43xx EVMs.
Signed-off-by: Pekon Gupta <pekon@ti.com>
This patch adds support of NOR cape[1] for both Beaglebone (white) and
Beaglebone(Black) boards. NOR Flash on this cape is connected to GPMC
chip-select[0] and accesses as external memory-mapped device.
This cape has 128Mbits(16MBytes), x16, CFI compatible NOR Flash device.
As GPMC chip-select[0] can be shared by multiple capes so NOR profile is
not enabled by default in boards.cfg. Following changes are required to
enable NOR cape detection when building am335x_boneblack board profile.
Signed-off-by: Tom Rini <trini@ti.com>
Beaglebone Board can be connected to expansion boards to add devices to them.
These expansion boards are called 'capes'. This patch adds support for
following versions of Beaglebone(AM335x) NAND capes
(a) NAND Device with bus-width=16, block-size=128k, page-size=2k, oob-size=64
(b) NAND Device with bus-width=16, block-size=256k, page-size=4k, oob-size=224
Further information and datasheets can be found at [1] and [2]
* How to boot from NAND using Memory Expander + NAND Cape ? *
- Important: As BOOTSEL values are sampled only at POR, so after changing any
setting on SW2 (DIP switch), disconnect and reconnect all board power supply
(including mini-USB console port) to POR the beaglebone.
- Selection of ECC scheme
for NAND cape(a), ROM code expects BCH8_HW ecc-scheme
for NAND cape(b), ROM code expects BCH16_HW ecc-scheme
- Selction of boot modes can be controlled via DIP switch(SW2) present on
Memory Expander cape.
SW2[SWITCH_BOOT] == OFF follow default boot order MMC-> SPI -> UART -> USB
SW2[SWITCH_BOOT] == ON boot mode selected via DIP switch(SW2)
So to flash NAND, first boot via MMC or other sources and then switch to
SW2[SWITCH_BOOT]=ON to boot from NAND Cape.
- For NAND boot following switch settings need to be followed
SW2[ 1] = OFF (SYSBOOT[ 0]==1: NAND boot mode selected )
SW2[ 2] = OFF (SYSBOOT[ 1]==1: -- do -- )
SW2[ 3] = ON (SYSBOOT[ 2]==0: -- do -- )
SW2[ 4] = ON (SYSBOOT[ 3]==0: -- do -- )
SW2[ 5] = OFF (SYSBOOT[ 4]==1: -- do -- )
SW2[ 6] = OFF (SYSBOOT[ 8]==1: 0:x8 device, 1:x16 device )
SW2[ 7] = ON (SYSBOOT[ 9]==0: ECC done by ROM )
SW2[ 8] = ON (SYSBOOT[10]==0: Non Muxed device )
SW2[ 9] = ON (SYSBOOT[11]==0: -- do -- )
[1] http://beagleboardtoys.info/index.php?title=BeagleBone_Memory_Expansion
[2] http://beagleboardtoys.info/index.php?title=BeagleBone_4Gb_16-Bit_NAND_Module
*IMPORTANT NOTE*
As Beaglebone board shares the same config as AM335x EVM, so following
changes are required in addition to this patch for Beaglebone NAND cape.
(1) Enable NAND in am335x_beaglebone board profile
(2) Add CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config because:
- AM335x EVM has NAND device with datawidth=8, whereas
- Beaglebone NAND cape has NAND device with data-width=16
Emails to Sandeep Paulraj <s-paulraj@ti.com>
have been bouncing.
Please assign new maintainer(s) to get these boards
back to Maintained.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Emails to the board maintainer
"Rishi Bhattacharya <rishi@ti.com>"
have been bouncing.
Tom suggested to remove this board.
Remove also omap1510_udc.c because this is the last board
to enable it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
There is the requirement on the chassis's backplane that when the clocks
have been enabled, they then should not disappear.
Resetting the Zarlink clocking chips at unit reset violates this
requirement because the backplane clocks are not supplied during the
reset time.
To avoid this side effect, both the Zarlink clocking chips are reset
only at power up.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
XFI is supported on T4QDS-XFI board, which removed slot3, and four LANEs
of serdes2 are routed to a SFP+ cages, which to house fiber cable or
direct attach cable(copper), the copper cable is used to emulate the
10GBASE-KR scenario.
So, for XFI usage, there are two scenarios, one will use fiber cable,
another will use copper cable. For fiber cable, there is NO PHY, while
for copper cable, we need to use internal PHY which exist in Serdes to
do auto-negotiation and link training, which implemented in kernel.
We use hwconfig to define cable type for XFI, and fixup dtb based on the
cable type.
For copper cable, set below env in hwconfig:
fsl_10gkr_copper:<10g_mac_name>
the <10g_mac_name> can be fm1_10g1, fm1_10g2, fm2_10g1, fm2_10g2. The
four <10g_mac_name>s do not have to be coexist in hwconfig. For XFI ports,
if a given 10G port will use the copper cable for 10GBASE-KR, set the
<10g_mac_name> of the port in hwconfig, otherwise, fiber cable will be
assumed to be used for the port.
For ex. if four XFI ports will both use copper cable, the hwconfig
should contain:
fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm2_10g1,fm2_10g2
For fiber cable:
1. give PHY address to a XFI port, otherwise, the XFI ports will not be
available in U-boot, there is no PHY physically for XFI when using fiber
cable, this is just to make U-boot happy and we can use the XFI ports
in U-boot.
2. fixup dtb to use fixed-link in case of fiber cable which has no PHY.
Kernel requests that a MAC must have a PHY or fixed-link.
When using XFI protocol, the MAC 9/10 on FM1 should init as 10G interface.
Change serdes 2 protocol 56 to 55 which has same feature as 56 since 56
is not valid any longer.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
mx6sxsabresd board has 2 FEC ports, each one connected to a AR8031.
Add support for one FEC port initially.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx6sxsabresd was not in the master branch when the conversion to the new Kconfig
style happened, so convert it now so that it can build again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
It is necessary to provide the same Vendor and Product IDs as the one in
the original Linux kernel code.
Without this change the USB mass storage gadget is not working with Windows7.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
The Gateworks Ventana EEPROM contains a set of configuration bits that
affect the removal of device-tree nodes that support peripherals that do not
exist on sub-loaded boards. This patch adds:
- a structure to define a config bit name, dt node alias, bit position
- an array of supported configuration items
- an econfig command to get/set/list configuration bits
- use of the array when adjusting the FDT prior to boot
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The PCISKT_WDIS# gpio allows for asserting WDIS# going to the various PCIe
sockets on the Ventana board.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The i2c_dis# pinmux/padconf was missing for the GW53xx (this feature was
added to the GW53xx on revB PCB's). Additionally, remove the duplicate
config for GW54xx.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks System Controller EEPROM config is flash based. Add a delay
following writes to avoid errors on back-to-back writes.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
NAND devices have differing layouts with respect to page size and pages per
block. These parameters affect the parameters that need to be passed to
mkfs.ubifs and ubinize used to create UBI images. The various NAND chips
supported by Gateworks Ventana fall into two different layouts which we
refer to as 'normal' and 'large'. This layout is useful when referencing
ubi files to download and flash so we create a dynamic env variable for it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the latest DDR initialization values suggested by the FSL hardware team.
While at it, add some comments for clarification.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Currently I don't have access to a mx31pdk board.
Magnus was the original maintainer of the board and accepted to take back
this role.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Now that Kconfig has a per-board option, we can use that directly rather
than inventing a custom define for the AS3722 code to determine which
board it's being built for.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds board support for the Toradex Colibri T30 module.
Working functions:
- SD card boot
- eMMC environment and boot
- USB host/USB client (on the dual role port)
- Network (via ASIX USB)
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On MarS usdhc3 is eMMC, on RIoT usdhc3 is uSD and eMMC is usdhc4.
Don't run the MarS specific eMMC reset code on usdhc3 when
board_type == BOARD_IS_RIOTBOARD
Signed-off-by: Iain Paton <ipaton0@gmail.com>
aristainetos board was merged in u-boot-imx before
Kconfig was integrated, but it is not yet
mainline.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Add deep sleep support in SPI/SD boot. The destination address
second stage uboot image is loaded to is changed because
currently this address will be used by kernel which means
we can't reserve it for resume.
Entry point to kernel is still placed in second stage uboot.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1042 has internal display interface unit (DIU) for driving video.
T1042RDB supports video mode via
-LCD using TI enconder
-HDMI type interface via HDMI encoder
Chrontel, CH7301C encoder which is I2C programmable is used
as HDMI connector on T1042RDB.
This patch add support to
-enable Video interface for T1042RDB
-route qixis multiplexing to enable DIU-HDMI interface on board
-program DIU pixel clock gerenartor for T1042
-program HDMI encoder via I2C on board
This patch refer to the upstream diu patch
(337b0c52b3) for T1040qds.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
[York Sun: resolve conflict and move changes to T104xRDB.h]
Reviewed-by: York Sun <yorksun@freescale.com>
The ch7301 encoder not only used in t1040qds platform, so we split
it for t1042rdb and LSx platform.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Automatic booting using an extlinux.conf file requires various environment
variables to be set.
Also modify CONFIG_SYS_LOAD_ADDR and CONFIG_STANDALONE_LOAD_ADDR to match
the value chosen for kernel_addr_r, see the added comment for why the new
value is chosen.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
SYS_CPU, SYS_BOARD and SYS_SOC are identical for all sunxi boards, move
them to a shared code block.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
It is redundant to use 'PFUZE100_PMIC' as the PMIC name because we already
know it is a PMIC.
Call it simply 'PFUZE100' instead.
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch configures the qrio to trigger a core reset on
a CPU reset request.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
To acheive this, the qrio_uprstreq() function that sets the UPRSTREQN
flag in the qrio RESCNF reg is added.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Check the core timer status register (TSR) for watchdog reset,
and and set the QRIO's reset reason flag REASON1[0] accordingly.
This allows the appliction SW to identify the cpu watchdog as a
reset reason, by setting the REASON1[0] flag in the QRIO.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
To achieve this, the qrio_cpuwd_flag() function that sets the CPU watchdog
flag in the REASON1 reg is added.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Banana Pi is an A20 based development board using Raspberry Pi compatible
IO headers. It comes with 1 GB RAM, 1 Gb ethernet, 2x USB host, sata, hdmi
and stereo audio out + various expansion headers:
http://www.lemaker.org/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for boards which I own and which already have a dts file in the
upstream kernel.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for boards which I own and which already have a dts file in the
upstream kernel.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for boards which I own and which already have a dts file in the
upstream kernel.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done
for sun7i only since I don't have access to any other sunxi platforms
with sata included.
The PHY setup is derived from the Alwinner releases and Linux, but is mostly
undocumented.
The Allwinner AHCI controller also requires some magic (and, again,
undocumented) DMA initialisation when starting a port. This is added under a
suitable ifdef.
This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on
contents of Linux DTS files, including SATA power pin config taken from the
DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.
The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.
After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.
TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
It's convenient to hold configurations for DDR3 PHY and EMIF in
separate common place. This patch moves K2HK DDR3 PHY and EMIF
configuration data with different rates and memory size to a common
ddr3_cfg.c file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch moves K2HK board directory to a common Keystone II board
directory. The Board related common functions are moved to a common
keystone board file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
With latest v3.13 kernel, unitrd dt fixup is not needed. However for
older kernel versions such as v3.8/v3.10, it is needed. So to work
with both, add a u-boot env variable that can be set to do dt fixup
for older kernels.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Use KS2_ prefix in all definitions, for that replace K2HK_ prefix and
add KS2_ prefix where it's needed. It requires to change names also
in places where they're used. Align lines and remove redundant
definitions in kardware-k2hk.h at the same time.
Using common KS2_ prefix helps resolve redundant redefinitions and
adds opportunity to use KS2_ definition across a project not thinking about
what SoC should be used. It's more convenient and we don't need to worry
about the SoC type in common files, hardware.h will think about that.
The hardware.h decides definitions of what SoC to use.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The SoC related common functions in board.c should be placed to
a common keystone.c arch file.
Acked-by: Murali Karicheri <m-maricheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
It's convinient to hold ddr3 function definitions in separate file
such as ddr3.h. So move this from hardware.h to ddr3.h.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
As noted by clang, we have been shifting certain values out of 32bit
range when setting some DDR registers. Upon further inspection these
had been touching reserved fields (and having no impact). These came in
from historical bring-up code and can be discarded. Similarly, we had
been declaring some fields as 0 when they will be initialized that way.
Tested on Beaglebone White.
Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-By: Ash Charles <ashcharles@gmail.com>
Add script to automate NAND flash process. As for now the board has
two burn scripts - burn to boot from SPI NOR flash and burn to boot
from AEMIF NAND flash, rename burn_uboot script to burn_uboot_spi.
Also update README to contain NAND burn U-boot process description.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Add in an init function for the drivers/power framework so we can dump
and read the registers via i2c.
Cc: Łukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
The alt board has R8A7794, 1GB DDR3-SDRAM, USB, Ethernet, QSPI,
MMC, SDHI and more.
This commit supports the following functions:
- DDR3-SDRAM
- SCIF
- I2C
- Ethernet
- QSPI
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The files ps7_init.c and ps7_init.h are supposed to be generated by
hw projects such as Vivado, PlanAhead and then to be copied into
board/xilinx/zynq directory.
But some prototypes in them cause annoying warning messages:
CC spl/board/xilinx/zynq/ps7_init.o
In file included from board/xilinx/zynq/ps7_init.c:50:0:
board/xilinx/zynq/ps7_init.h:137:1: warning: function declaration isn't a prototype [-Wstrict-prototypes]
board/xilinx/zynq/ps7_init.h:138:1: warning: function declaration isn't a prototype [-Wstrict-prototypes]
board/xilinx/zynq/ps7_init.h:139:1: warning: function declaration isn't a prototype [-Wstrict-prototypes]
board/xilinx/zynq/ps7_init.h:145:1: warning: function declaration isn't a prototype [-Wstrict-prototypes]
board/xilinx/zynq/ps7_init.c:12602:1: warning: function declaration isn't a prototype [-Wstrict-prototypes]
board/xilinx/zynq/ps7_init.c:12723:1: warning: function declaration isn't a prototype [-Wstrict-prototypes]
board/xilinx/zynq/ps7_init.c:12742:1: warning: function declaration isn't a prototype [-Wstrict-prototypes]
board/xilinx/zynq/ps7_init.c:12761:1: warning: function declaration isn't a prototype [-Wstrict-prototypes]
board/xilinx/zynq/ps7_init.c:12854:6: warning: function declaration isn't a prototype [-Wstrict-prototypes]
The prototypes should be
int ps7_init(void);
int ps7_post_config(void);
int ps7_debug(void);
rather than
int ps7_init();
int ps7_post_config();
int ps7_debug();
We do not want to be bothered because of automatically generated files.
But we cannot touch the external projects for now.
What we can do is to disable -Wstrict-prototypes for ps7_init.c
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At present stdio device functions do not get any clue as to which stdio
device is being acted on. Some implementations go to great lengths to work
around this, such as defining a whole separate set of functions for each
possible device.
For driver model we need to associate a stdio_dev with a device. It doesn't
seem possible to continue with this work-around approach.
Instead, add a stdio_dev pointer to each of the stdio member functions.
Note: The serial drivers have the same problem, but it is not strictly
necessary to fix that to get driver model running. Also, if we convert
serial over to driver model the problem will go away.
Code size increases by 244 bytes for Thumb2 and 428 for PowerPC.
22: stdio: Pass device pointer to stdio methods
arm: (for 2/2 boards) all +244.0 bss -4.0 text +248.0
powerpc: (for 1/1 boards) all +428.0 text +428.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
There is no point in setting a structure's memory to NULL when it has
already been zeroed with memset().
Also, there is no need to create a stub function for stdio to call - if the
function is NULL it will not be called.
This is a clean-up, with no change in functionality.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
This patch adds the changes to boards.cfg and the board directory
under board/tqc.
TQMa6 is a family of modules based on Freescale i.MX6. It consists of
TQMa6Q (i.MX6 Quad), TQMa6D (i.MX6 Dual) featuring eMMC, and 1 GiB DDR3
TQMa6S (i.MX6 Solo) featuring eMMC and 512 MiB DDR3
The modules need a baseboard. Initially the MBa6x starterkit mainboard is
supported. To easy support for other mainboards the functionality is splitted
in one file for the module (tqma6.c) and one file for the baseboard (tqma6_
mba6).
The modules can be boot from eMMC (on USDHC3) and SPI flash.
The following features are supported:
- MMC: eMMC on module (on USDHC3) and SD-card (on MBa6x mainboard)
- Ethernet: RGMII using micrel KSZ9031 phy on MBa6x mainboard for TQMa6<x> module.
The phy needs special configurations for the pad skew registers to adjust for
the signal routing.
Also support for standard ethernet commands and uppdate via tftp.
- SPI: ECSPI1 with bootable serial flash on module and two additional
chip selects on MBa6x
- I2C: This patch adds support for the I2C busses on the TQMa6<x> modules (I2C3)
and MBa6x baseboards (I2C1). The LM75 temperature sensors on TQMa6<x> and MBa6x
are also configured.
- USB: high speed host 1 on MBa6x and support for USB storage
- PMIC: support for pfuze 100 on TQMa6<x>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
There is no need to keep iomuxc_base_regs structure as it serves the exact same
purpose of the iomuxc structure, which is to provide access to the GPR
registers.
The additional fields of iomuxc_base_regs are not used. Other advantage of
'iomuxc' is that it has a shorter name and the variable declarations can fit
into a single line.
So remove iomuxc_base_regs structure and use iomuxc instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
T4240 has 4 serdes, each serdes has 4k memory space, two PLLs.
We use PLL1CR0 to check the serdes reference clock.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
find_tlb_idx() is called in board_early_init_r() on multiple boards.
The return value is not checked before being used to disable a TLB.
In normal case the return value wouldn't be -1. In case of a mis-
configuration during porting to a new board, checking the return value
may be helpful to reveal some user errors.
Signed-off-by: York Sun <yorksun@freescale.com>
Since P1023RDS is no longer supported/manufactured by Freescale,
we clean up P1023RDS related code.
Since P1023RDB is still supported by Freescale,
we keep P1023RDB releated code.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The latest GCC is so clever that it reports more warnings
than old ones did:
------------------------------>8------------------------------
board/freescale/m5253demo/flash.c: In function 'flash_get_offsets':
board/freescale/m5253demo/flash.c:65:23: warning: iteration 2047u
invokes undefined behavior [-Waggressive-loop-optimizations]
info->start[k + 1] = info->start[k] + CONFIG_SYS_SST_SECTSZ;
^
board/freescale/m5253demo/flash.c:64:3: note: containing loop
for (k = 0, j = 0; j < CONFIG_SYS_SST_SECT; j++, k++) {
^
------------------------------8<------------------------------
The cause of the warning is like this:
The for statement iterates 2048 times in flash_get_offsets() func.
(Notice CONFIG_SYS_SST_SECT is defined as 2048)
The last iteration does
info->start[2048] = info->start[2047] + CONFIG_SYS_SST_SECTSZ;
causing an undefined behavior.
(Please note the array size of info->start is 2048.
CONFIG_SYS_MAX_FLASH_SECT is defined as 2048 for this board.)
This commit fixes that so as not to overrun the info->start array.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jason Jin <Jason.jin@freescale.com>
There is only one line diff between LEON2 and LEON3 linker scripts:
- arch/sparc/cpu/leon2/start.o (.text)
+ arch/sparc/cpu/leon3/start.o (.text)
They can be written in the same way:
*/start.o (.text)
So, board/gaisler/grsim_leon2/u-boot.lds
and arch/sparc/cpu/leon3/u-boot.lds
can be merged into arch/sparc/cpu/u-boot.lds.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
The linker scripts of LEON3
- board/gaisler/grsim/u-boot.lds
- board/gaisler/gr_cpci_ax2000/u-boot.lds
- board/gaisler/gr_ep2s60/u-boot.lds
- board/gaisler/gr_xc3s_1500/u-boot.lds
are the same (except cosmetic differences such as indentation).
This commit merges them into arch/sparc/cpu/leon3/u-boot.lds.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Rather than calling do_source directly (which is not officially exported
from cmd_source.c) call 'source' which is exported and requires a little
less code to do so as well.
Signed-off-by: Tom Rini <trini@ti.com>
This is a sun7i (A20) based followup to the sun4i (A10)
Cubieboard. It has GMAC using MII mode.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Similar to the USB NIC found on OMAP5uEVM, PandaBoard and BeagleBoard-XM
boards, the sunxi SoCs have a NIC onboard without an embedded MAC address.
Just like the omap used on these boards, the sunxi SoCs do have a unique chip
id, in the form of the 128 bit SID register:
http://linux-sunxi.org/SID_Register_Guide
So mimick the BeagleBoard-XM board code (commit 548a64d8) and use the chip id
to generate a unique fixed MAC address.
We check for the SID not being all 0, since some early A20 batches
shipped without having there SID programmed.
Note we use specific parts of the 128 bits, since some parts indicate the
SoC family / revision, and thus are fixed. The algorithm for this was taken
from the linux-sunxi.org kernels.
Signed-off-by: Jonathan Liu <net147@gmail.com>
[hdegoede@redhat.com: Expanded the commit message with some more info]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the x-powers axp152 pmic which is found on most A10s boards
and enable it for the r7-tv-dongle board.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the x-powers axp209 pmic which is found on most A10, A13 and
A20 boards.
And enable AXP209 support for the Cubietruck and Cubieboard boards.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the i2c controller found on all Allwinner sunxi SoCs,
this is the same controller as found on the Marvell orion5x and kirkwood
SoC families, with a slightly different register layout, so this patch uses
the existing mvtwsi code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
[ ijc -- updated u-boot-spl-fel.lds ]
For proper displayport performance, scrambling has to be enabled, but
is turned off on DP501 by default.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
The I2C bridge on DP501 supports EDID, MCCS and HDCP by default.
Allow EDID only to avoid I2C address conflicts.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
readl was called with values instead of pointers to these values.
Why this ever did work is a mystery...
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
* Boot failures have been discovered due to a combination of routing issues and
non optimal ddr3 timings in the EMIF
* Since ddr3 timings are different after significant board layout changes
different timings are required for alpha, beta and production boards.
Signed-off-by: Franklin S. Cooper Jr <fcooper@ti.com>
J6 EVM can be built with UART3 as console, but currently
there's nothing muxing UART3 correctly. Likely this only
works because, based on commit log, author was only testing
with UART3 boot and - I assume - ROM code leave UART3 correctly
muxed in that case.
If we want to boot from MMC and still use UART3 as console,
then we need to mux those signals correctly.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Many A20 boards (ie Cubieboard2, A20-OLinuXino_MICRO) use an 100 Mbit MII
phy together with the GMAC nic found in the A20 SoC, add support for this
(this will get used when we add these boards in a later patch).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the Allwinner A13 and A10s SoCs also know as the Allwinner
sun5i family, and the A13-OLinuXinoM A13 based and r7-tv-dongle A10s based
boards.
The only differences compared to the already supported sun4i and sun7i
families are all in the DRAM controller initialization:
-Different hcpr values
-Different MBUS settings
-Some other small initialization changes
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the Allwinner A10 SoC also known as the Allwinner sun4i family,
and add the Cubieboard board which uses the A10 SoC.
Compared to sun7 only the DRAM controller is a bit different:
-Controller reset bits are inverted, but only for Rev. A
-Different hpcr values
-No MBUS on sun4i
-Various other initialization changes
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
To move the arch common function away from board folder to
arch/arm/cpu/armv7/socfpga folder. Its to avoid code duplication
for other non Altera dev kit which is using socfpga device.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Scan Manager driver will be called to configure the IOCSR
scan chain. This configuration will setup the IO buffer settings
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
This patch returns back support for old ep93xx processors family
Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
LS2085A is an ARMv8 implementation. This adds board support for emulator
and simulator:
Two DDR controllers
UART2 is used as the console
IFC timing is tightened for speedy booting
Support DDR3 and DDR4 as separated targets
Management Complex (MC) is enabled
Support for GIC 500 (based on GICv3 arch)
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
The armv8 ARM Trusted Firmware (ATF) can be used to load various ATF
images and u-boot, and does this for virtual platforms by using
semihosting. This commit extends this idea by allowing u-boot to also
use semihosting to load the kernel/ramdisk/dtb. This eliminates the need
for a bootwrapper and produces a more realistic boot sequence with
virtual models.
Though the semihosting code is quite generic, support for armv7 in
fastmodel is less useful due to the wide range of available silicon
and the lack of a free armv7 fastmodel, so this change contains an
untested armv7 placeholder for the service trap opcode.
Please refer to doc/README.semihosting for a more detailed description
of semihosting and how it is used with the armv8 virtual platforms.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Cc: trini@ti.com
Cc: fenghua@phytium.com.cn
Cc: bhupesh.sharma@freescale.com
The u-boot Overo board actually supports both Overo (OMAP35xx)
and Overo Storm (AM/DM37xx) COMs with a range of different expansion
boards. This provides a mechanism to select the an appropriate device
tree file based on the processor version and, if available, the
expansion board ID written on the expansion board EEPROM. To match the
3.15+ kernels, fdtfile names have this format:
"omap3-overo[-storm]-<expansion board name>.dtb"
By default, we use "omap3-overo-storm-tobi.dtb".
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Conflicts:
include/configs/omap3_overo.h
AM437x Starter Kit has a qspi flash and gbit ethernet
support. By muxing those signals, we can use those
interfaces from u-boot.
Signed-off-by: Felipe Balbi <balbi@ti.com>
AM43xx Starter Kit is a new board based on
AM437x line of SoCs. Being a low-cost EVM and
small size EVM are intended to provide an entry
level development platform on a full fledged
Hardware System.
Signed-off-by: Felipe Balbi <balbi@ti.com>
when porting u-boot to a new am43xx board, it
helps to know the name of the current unsupported
board so we don't have to hunt for design documents
to figure out what's written in the EEPROM.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF
definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>
nios-32 arch was removed back in 2010 (1117cbf). Code depending on
its headers (nios.h, nios-io.h) can't possibly compile since then.
As it wasn't fixed till now it is safe to remove.
Signed-off-by: Vasili Galka <vvv444@gmail.com>
commit 18b06652cd "tools: include u-boot version of sha256.h"
unconditionally forced the sha256.h from u-boot to be used
for tools instead of the host version. This is fragile though
as it will also include the host version. Therefore move it
to include/u-boot to join u-boot/md5.h etc which were renamed
for the same reason.
cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Fix the following warning messages:
In function 'flash_erase': 180:21:
warning: variable 'last' set but not used [-Wunused-but-set-variable]
In function 'write_buff': 322:10:
warning: variable 'port_width' set but not used [-Wunused-but-set-variable]
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
From comparison of current logic and the logic that was prior to commit
aba27ac, we see that first parameter of FPGA_GET_REG() shall be the
FPGA index and not channel number. The re-factoring in commit aba27ac
accidentally changed that.
Cc: Stefan Roese <sr@denx.de>
Acked-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Vasili Galka <vvv444@gmail.com>
Generic board support is now enabled for Exynos 4, and if any
init function returns an error then the init process is stopped.
This makes a boot issue on the Trats and Trats2 devices. If the device
is supplied by USB cable or an external power supply then it can't boot
because function exynos_power_init returns an error. Now this function
returns 0 if battery is not connected.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Piotr Wilczek <p.wilczek@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Explain the necessary steps in order to boot from SPI NOR.
Based on a earlier submission from Mårten Wikman.
Signed-off-by: Mårten Wikman <marten.wikman@novia.fi>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Clang interpretes an if condition like "if ((a = b) == NULL)
as it tries to assign a value in a statement. Hence if you do
"if ((something)) it warns you that you might be confused.
Hence drop the double braces for plane if statements.
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Most of the warnings seem to be related to using 'int' for size_t. Change
this and fix up the remaining warnings and problems. For bootm, the warning
was masked by others, and there is an actual bug in the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
run_command() returns 0 for success, 1 for failure. Fix places which
assume that failure is indicated by a negative return code.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Stefan Roese <sr@denx.de>
This should include the hash so that image_binary_size is really at the
end of the image, and not some 300 bytes earlier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add QSPI support for VF610TWR, such as clock and iomux.
Signed-off-by: Alison Wang <Huan.Wang@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>
