STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
-----BEGIN PGP SIGNATURE-----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=s7xn
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
This patch series adds support for ZFS listing and load to u-boot.
To Enable zfs ls and load commands, modify the board specific config file with
#define CONFIG_CMD_ZFS
Steps to test:
1. After applying the patch, zfs specific commands can be seen
in the boot loader prompt using
UBOOT #help
zfsload- load binary file from a ZFS file system
zfsls - list files in a directory (default /)
2. To list the files in zfs pool, device or partition, execute
zfsls <interface> <dev[:part]> [POOL/@/dir/file]
For example:
UBOOT #zfsls mmc 0:5 /rpool/@/usr/bin/
3. To read and load a file from an ZFS formatted partition to RAM, execute
zfsload <interface> <dev[:part]> [addr] [filename] [bytes]
For example:
UBOOT #zfsload mmc 2:2 0x30007fc0 /rpool/@/boot/uImage
References :
-- ZFS GRUB sources from Solaris GRUB-0.97
-- GRUB Bazaar repository
Jorgen Lundman <lundman at lundman.net> 2012.
21e25992c8