- New PX30 board: Engicam PX30.Core;
- Fix USB HID support for rock960;
- Remove host endianness dependency for rockchip mkimage;
- dts update for rk3288-tinker;
- Enable console MUX for some ROCKPi boards;
- Add config-based ddr selection for px30;
Like, rk3399 the rk3288 also supports 4K resolution.
So, enable it for rk3288 with HDMI platforms.
Right now, rockchip video drivers are supporting for rk3288,
rk3399 SoC families, so mark the 4K resolution by default
if it's an HDMI video out.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Found this by comparing it to the coreboot driver, a form of this call
was introduced there in their commit b9a7877568cf ("rockchip/*: refactor
edp driver"). This is copy-pasted from U-Boot's link_train_cr() slightly
above it.
Without this on a gru-kevin chromebook, I have:
clock recovery at voltage 0 pre-emphasis 0
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
channel eq failed, ret=-5
link train failed!
rk_vop_probe() Device failed: ret=-5
With this, it looks like training succeeds:
clock recovery at voltage 0 pre-emphasis 0
requested signal parameters: lane 0 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 3.5dB
using signal parameters: voltage 0.4V pre_emph 3.5dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 6dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 6dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 6dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 6dB
using signal parameters: voltage 0.4V pre_emph 6dB
requested signal parameters: lane 0 voltage 0.4V pre_emph 0dB
requested signal parameters: lane 1 voltage 0.4V pre_emph 0dB
requested signal parameters: lane 2 voltage 0.4V pre_emph 0dB
requested signal parameters: lane 3 voltage 0.4V pre_emph 0dB
using signal parameters: voltage 0.4V pre_emph 0dB
channel eq at voltage 0 pre-emphasis 0
config video failed
rk_vop_probe() Device failed: ret=-110
The "config video failed" error also goes away when I disable higher
log levels, and it claims to have successfully probed the device.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Done with:
./tools/moveconfig.py VIDEO_BMP_GZIP
The 3 suspicious migration because CMD_BMP and SPLASH_SCREEN
are not activated in these defconfigs:
- trats_defconfig
- s5pc210_universal_defconfig
- trats2_defconfig
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For levels equal to the maximum value, the duty cycle must be equal to
the period.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Amlogic D-PHY in the Amlogic AXG SoC Family does support a frequency
higher than 10MHz for the TX Escape Clock, thus make the target rate
configurable.
This is based on the Linux commit [1] and adapted to the U-Boot driver.
[1] a328ca7e4af3 ("drm/bridge: dw-mipi-dsi: permit configuring the escape clock rate")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The timing values for dw-dsi are often dependent on the used display and
according to Philippe Cornu will most likely also depend on the used phy
technology in the soc-specific implementation.
To solve this and allow specific implementations to define them as needed
add a new get_timing callback to phy_ops and call this from the dphy_timing
function to retrieve the necessary values for the specific mode.
This is based on the Linux commit [1] and adapted to the U-Boot driver.
[1] 25ed8aeb9c39 ("drm/bridge/synopsys: dsi: driver-specific configuration of phy timings")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Yannick Fertré <yannick.fertre@st.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
There is no member `dev` in dw_mipi_dsi, but there is one in mipi_dsi_host,
so use that.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
All platforms support bi_dram[] since quite some time. Lets remove the
and bi_memsize values completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SPLASH_SCREEN
CONFIG_SPLASH_SCREEN_ALIGN
CONFIG_SPLASHIMAGE_GUARD
CONFIG_SPLASH_SOURCE
Signed-off-by: Simon Glass <sjg@chromium.org>
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXykjtQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76a1WQCcD+objdS+90mDdT0yTpW3jHS4YiwAn2V2rTTo
4hKj5yxRg3cvb/pBAmbQ
=TyRs
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200804' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2020.10
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
Since commit 7812bbdc37 ("video: Correctly handle multiple
framebuffers") the vidconsole output is missing on the primary
display on boards with two IPU units (all i.MX6Q/D based boards).
The base address of the allocated framebuffer is not correctly
programmed in the display controller. Fix it.
Reported-by: Soeren Moch <smoch@web.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Soeren Moch <smoch@web.de>
Continuing with the approach in commit <addf358bac1d2bd0> rename
additional drivers to allow the OF_PLATDATA support.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- nexell_display.c: Changed to DM, CONFIG_FB_ADDR can not be used
anymore because framebuffer is allocated by video_reserve() in
video-uclass.c. Therefore code changed appropriately.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
possible (and similar).
- livetree API (dev_read_...) is used instead of fdt one (fdt...).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Low level functions for DPC (Display Controller) and Makefile for all
nexell video low level functions.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
When using OF_PLATDATA, the bind process between devices and drivers
is performed trying to match compatible string with driver names.
However driver names are not strictly defined, and also there are different
names used when declaring a driver with U_BOOT_DRIVER, the name of the
symbol used in the linker list and the used in the struct driver_info.
In order to make things a bit more clear, rename the drivers names. This
will also help for further OF_PLATDATA improvements, such as checking
for valid driver names.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a fix for sandbox of-platdata to avoid using an invalid ANSI colour:
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the video driver to support this feature and enable it on
minnowmax to speed up the display.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from over 13 seconds to
300ms, at 1280x1024.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update the video driver to support this feature and enable it on link.
Also remove the multi-line scrolling since normal scrolling is fast enough
now.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from about 930ms to 29ms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update the video driver to support this feature and enable it on samus.
Also remove the multi-line scrolling since normal scrolling is fast enough
now.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from about 430ms to 12ms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For PCI video devices that are not mentioned in the devicetree, U-Boot
does not bind a driver before relocation, since PCI is not fully probed
at that point. Furthermore it is possible for the video device to be on
a secondary bus which is not even scanned.
This is fine if the framebuffer is allocated in fixed memory, as it
normally is on x86. But when using this as a copy framebuffer, we also
need U-Boot to allocate its own cached framebuffer for working in. Since
the video driver is never bound before relocation, the framebuffer size
is never set and U-Boot does no allocation.
Add a new CONFIG option to reserve 16MB of memory for this eventuality.
This allows vesa devices to use the copy framebuffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present video_bottom is set to the bottom of each framebuffer when it
is allocated. This is not correct, since it should hold the bottom of the
entire area available for framebuffers.
Fix this by adding a private address in the uclass which keeps track of
the next available spot for a framebuffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Enable this feature on sandbox by updating the SDL driver to have two
framebuffers.
Update the video tests to check that the copy framebuffer is kept in sync.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Adjust the bitmap code to sync to the copy framebuffer when done.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update the implementation to keep a track of what it changes in the frame
buffer and then tell the copy buffer about it. Use the special
vidconsole_memmove() helper so that memmove() operations are also
reflected in the copy buffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update the implementation to keep a track of what it changes in the frame
buffer and then tell the copy buffer about it. Use the special
vidconsole_memmove() helper so that memmove() operations are also
reflected in the copy buffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update the implementation to keep a track of what it changes in the frame
buffer and then tell the copy buffer about it. Use the special
vidconsole_memmove() helper so that memmove() operations are also
reflected in the copy buffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add a convenience function to call video_sync_copy() for a vidconsole.
Also add a memmove() helper, which does the memmove() as well as the sync.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update video_clear() to also sync to the copy framebuffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This framebuffer is separately mapped. Update the video post-probe
function to set this up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Some architectures use a cached framebuffer and flush the cache as needed
so that changes are visible. This is supported by U-Boot.
However x86 uses an uncached framebuffer with a 'write-combining' feature
to speed up writes. Reads are permitted but they are extremely expensive.
Unfortunately, reading from the frame buffer is quite common, e.g. to
scroll it. This makes scrolling very slow.
Add a new feature which supports copying modified parts of the frame
buffer to the uncached hardware buffer. This speeds up scrolling by at
least 10x on x86 so the extra complexity cost seems worth it.
As a starting point, add the Kconfig, update the video structures to keep
track of the buffer and add a function to do the copy.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present when the console is rotated 180 degrees it starts almost a
whole character to the left of the right edge (typically 7 pixels with
an 8-pixel-wide font). On a display which aligns with the font width,
this just wastes space. On a display that does not this can result in
x_frac going negative for the final character (the one on the left
side) and the overflow -EAGAIN check at the start of the function
failing.
Change the function to start at the rightmost pixel to fix these
problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
