It seems that the time can change in between getting it and reading the
offset. Check for this and try again if this happens.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since resetting the RTC on sandbox causes it to read the base time from
the system, we cannot rely on this being unchanged since it was last read.
Allow for a one-second delay.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Fixes: https://source.denx.de/u-boot/u-boot/-/issues/4
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Reported-by: Tom Rini <trini@konsulko.com>
Suggested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Simon Glass <sjg@chromium.org>
Some tests can have race conditions which are hard to detect on a single
one. Add a way to run tests more than once, to help with this.
Each individual test is run the requested number of times before moving
to the next test. If any runs failed, a message is shown.
This is most useful when running a single test, since running all tests
multiple times can take a while.
Signed-off-by: Simon Glass <sjg@chromium.org>
LTO (Link-Time Optimisation) is an very useful feature which can
significantly reduce the size of U-Boot binaries. So far it has been
made available for selected ARM boards and sandbox.
However, incremental builds are much slower when LTO is used. For example,
an incremental build of sandbox takes 2.1 seconds on my machine, but 6.7
seconds with LTO enabled.
Add a NO_LTO parameter to the build, similar to NO_SDL, so it can be
disabled during development if needed, for faster builds.
Add some documentation about LTO while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is currently a problem that U-Boot can not work on ARMv4
because assembly imlementations of memcpy() and some other functions
use "bx lr" instruction that is not available on ARMv4 ("mov pc, lr"
should be used instead).
A working preprocessor-based solution to this problem is found in
arch/arm/lib/relocate.S. Move it to the "ret" macro in
arch/arm/include/asm/assembler.h and change all "bx lr" code
to "ret lr" in functions that may run on ARMv4. Linux source code
deals with this problem in the same manner.
v1 -> v2:
Comment update. Pointed out by Andre Przywara.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
CC: Samuel Holland <samuel@sholland.org>
CC: Ye Li <ye.li@nxp.com>
CC: Simon Glass <sjg@chromium.org>
CC: Andre Przywara <andre.przywara@arm.com>
CC: Marek Vasut <marex@denx.de>
CC: Sean Anderson <sean.anderson@seco.com>
CC: Tom Rini <trini@konsulko.com>
This command is being introduced with the goal of allowing user-friendly
"generic use case" U-Boot builds to pause until user input under some
situations.
The main use case would be when a boot failure happens, to pause until
the user has had time to acknowledge the current state.
Tested using:
make && ./u-boot -v -T -c 'ut lib lib_test_hush_pause'
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Cc: Simon Glass <sjg@chromium.org>
Try to load required DTB overlays if the board supports extensions and
CONFIG_CMD_EXTENSION is enabled.
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Enable d-cache early in SPL right after DRAM is started up.
This reduces U-Boot proper load time by 650ms when loaded
from SPI NOR.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Introduce the new Kconfig symbol CONFIG_SPL_SYS_L2_PL310 to allow the
SPL to build cache-pl310.c.
Before this commit, the SPL could enable the PL310 L2 cache [1], but the
cache maintenance functions from cache-pl310.c were only useable for
non-SPL builds.
After enabling the cache one must be able to flush it, too. Thus this
commit allows cache-pl310.c to be included in the SPL build.
[1] See for example arch/arm/mach-imx/cache.c: v7_outer_cache_enable()
Signed-off-by: Philip Oberfichtner <pro@denx.de>
This converts CONFIG_SYS_L2_PL310 to Kconfig.
For omap2 and mvebu the 'select SYS_L2_PL310' locations were
determined using ./tools/moveconfig -i CONFIG_SYS_L2_PL310.
For mx6 I manually chose ARCH_MX6 as 'select' location. The
correctness has been verified using
$ ./tools/moveconfig.py -f ARCH_MX6 ~SYS_L2_PL310 ~SYS_L2CACHE_OFF
0 matches
That means whenever an ARCH_MX6 board had SYS_L2_PL310 disabled, this
was correctly reflected in SYS_L2CACHE_OFF. Thus it's safe to insert
the 'select' statement under ARCH_MX6.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
This removes the following symbols:
CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS
CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS
CONFIG_SYS_I2C_LDI_ADDR
CONFIG_SYS_I2C_DVI_ADDR
CONFIG_SYS_I2C_DVI_BUS_NUM
They are unused by any code in tree at this time.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_I2C_EEPROM_CCID
CONFIG_SYS_I2C_EEPROM_NXID
CONFIG_SYS_EEPROM_BUS_NUM
Signed-off-by: Tom Rini <trini@konsulko.com>
We can check if the message was acknowledged in the common
ti_sci_do_xfer() which lets us remove it from after each call to this
function. This simplifies the code and reduces binary size.
Signed-off-by: Andrew Davis <afd@ti.com>
The inline hint is not needed here, the compiler will do the right thing
based on if we are compiling for speed or for code size. In this case the
inline causes this function to be placed inside each callsite which is
not the right thing to do for either speed nor size. There is no
performance benefit to this due to the larger function size reducing
cache locality, but there is a huge size penalty. Remove inline keyword.
Signed-off-by: Andrew Davis <afd@ti.com>
We don't need to print the same message in every location, just
print it in the function that fails and remove all the extra
message printouts.
Signed-off-by: Andrew Davis <afd@ti.com>
This ti_sci_do_xfer() function already prints out the reason for the
failure, and the caller of each of these functions should also notify
the user of the failed task. Remove this extra level of error message.
Signed-off-by: Andrew Davis <afd@ti.com>
Currently for all Qcom SoCs/boards there are separate compatibles for
GPIO and pinctrl. But this is inconsistent with official (upstream) Linux
bindings which requires only a single compatible "qcom,<SoC name>-pinctrl"
and there is no such compatible property as "qcom,tlmm-<SoC name>".
So fix this inconsistency for Qcom SoCs in order to comply with upstream
DT bindings. This is done via removing compatibles from "msm_gpio" driver
and via binding to "msm_gpio" driver from pinctrl driver in case
"gpio-controller" property is specified for pinctrl node.
Suggested-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
DT compatible is sufficient to make platform specific differentiation,
so remove redundant CONFIG_SDM845 check.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Enable USB config options along with its dependencies like PHY, RESET,
PMIC GPIO etc. config options.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
For USB3 host controller to detect devices on the bus it is required to
enable a PMIC GPIO: usb_vbus_boost_pin. So enable that during board
specific initialization.
And since this PMIC GPIO parsing is quite u-boot specific, so add a
DT override to qcs404-evb-uboot.dtsi to represent usb_vbus_boost_pin.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
GPIO LV (low voltage)/MV (medium voltage) subtypes have different
features and register mappings than 4CH/8CH subtypes. Add support
for LV and MV subtypes.
With GPIO LV/MV subtype available, add "qcom,pms405-gpio" compatible
which requires support for GPIO MV subtype.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Since both pm8916.c and pm8916_gpio.c are already supporting multiple
Qcom SoCs, it makes sense to rename these drivers to pmic_qcom.c and
qcom_pmic_gpio.c respectively. Also, these driver can be extended to
support additional functionality if required for other Qcom SoCs.
Along with this import latest DT binding: qcom,spmi-pmic.txt from Linux
kernel and thereby remove pm8916.txt.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
QCS404 SoC provides support for two USB controllers: one USB3 and the
other one being USB2. The USB3 controller supports further 2 PHY: one high
speed PHY and the other super speed PHY. The USB2 controller supports a
single high speed PHY. So add corresponding DT nodes.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Drivers like USB, ethernet etc. uses ".enable" hook to enable clocks.
So add corresponding support for Qcom clock drivers.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Since the base functionality remains the same for a reset driver on Qcom
SoCs, so leverage that to convert ipq4019 specific reset driver to a
generic Qcom reset driver. With that one just need to provide SoC specific
reset table.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
QCS404 SoC supports two types of PHY, one supports high speed mode or
USB2 PHY and the other supports super speed mode or USB3 PHY. So add
corresponding PHY drivers.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Remove the main_cpsw0_qsgmii_phyinit variable from the boot
command as there is no ethernet firmware in j721s2.
Fixes: 8886341aa6 ('configs: j721s2_evm_a72_defconfig: Add A72 specific defconfig')
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Re-sync again on some linux part, add some fixes for fsl_elbc from
Pali and switch
imx8mn bsh to use nand base ident
For nand subsystem tested on:
- imx8mn Macronix MX30LF4G18AC
- P2020 based board Turris 1.1 for fsl_elbc
- kirkwood: pogo_v4 & nsa310s: Add distro boot (Tony)
- kirkwood: add DM timer support and use it on lsxl boards (Michael)
- kirkwood: convert the Buffalo Linkstation LS-CHLv2 and XHL boards
to DM (Michael)
- mvebu: turris_mox/omnia: misc improments (Pali)
- mvebu: mbus: Fix mbus driver to work also after U-Boot relocation (Pali)
The board has only one network interface. The linux kernel will
gracefully skip a the ethernet interface if no connected PHY could be
probed. u-boot on the other hand will throw an error message. The kernel
device tree is about to be fixed. For now, just disable the ethernet
interface in our -u-boot.dtsi.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
DM_SERIAL needs early malloc. The on-chip RAM is pretty tight, it's only
2kiB, with DM_SERIAL enabled, this doesn't work anymore. Fortunately for
us, we don't need the on-chip RAM because the DRAM is already
initialized before u-boot starts. Just put the early malloc area there
and use the default early malloc size.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Just enabling the Kconfig option for DM_ETH and DM_MDIO is enough.
Additionally, we can remove the old hardcoded config.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the new mvebu GPIO driver and convert all the function calls to the
former kirkwood GPIO driver. This means that we are now using the LED
uclass and the regulator uclass. Unfortunately, the GPIO LED doesn't
offer a blinking method. Thus we are now stuck with solid on and off
states, which makes debugging a bit harder. Also, there is no GPIO fan
driver for now.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
If something is wrong with the environment, we cannot rely on a proper
u-boot operation anymore. In fact, it is possible, that we never reach
misc_init_r() with a broken environment.
Also don't enable the netconsole by environment settings. This way the
user don't have to reconfigure the environment. Instead the network
console is only enabled when the push button is pressed during boot.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
We still need to be able to boot legacy images. Esp. the debian
installer will have a kernel with an appended DTB.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the common kernel_addr_r, ramdisk_addr_r and fdt_addr_r variable
names.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
We can load the ramdisk as the last step. This way we don't have to set
the intermediate variable 'ramdisk_len' and can remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
